Some of traced MMIO registers are a large continuous section. These
stuffed the MMIO lookup hash table and so waste lots of memory and
get much lower lookup performance.

Here we picked out these sections by special handling. These sections
include:
  o Display pipe registers, total 768.
  o The PVINFO page, total 1024.
  o MCHBAR_MIRROR, total 65536.
  o CSR_MMIO, total 3072.

So we removed 70,400 items from the hash table, and speed up guest
boot time by ~500ms.

v2:
  o add a local function find_mmio_block().
  o fix comments.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

add gtt_invalidate API to handle the GTT TLB flush instead of
hiding in write_pte64 function. This can avoid overkill when using
write_pte64
Suggested-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

In some cases, GVT-g is accessing MMIO without holding runtime_pm
and this patch can add the inline API for doing the runtime_pm get/put
to make sure when accessing HW MMIO the i915 HW is really powered on.
Suggested-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

This flag is already set in the top level Makefile of the kernel.

Also, by having set CONFIG_DRM_I915_GVT, thereby appending -Wall to
ccflags, you undo all the -Wno-* cflags previously set in the Make
variable KBUILD_CFLAGS.

For example:

cc foo.c -Wall -Wno-format -Wall

resets -Wformat.
Signed-off-by: Nick Desaulniers <nick.desaulniers@gmail.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

remove all the legacy pre-BDW mmio handlers and the corresponding
usage/definition since pre-BDW platforms are not supported in GVT
environment.

v2:
- clean up all the left dirty code before BDW, e.g
  all D_HSW usage and itself, D_IVB, D_PRE_BDW. (Zhenyu)
v3:
- change is based on gvt-staging. (Zhenyu)
Signed-off-by: fred gao <fred.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

The time based scheduler poll context busy status at every
micro-second during vGPU switch, it will make GPU idle for a while
when the context is very small and completed before the next
micro-second arrival. Trigger scheduling immediately after context
complete will eliminate GPU idle and improve performance.

Create two vGPU with same type, run Heaven simultaneously:
Before this patch:
 +---------+----------+----------+
 |         |  vGPU1   |   vGPU2  |
 +---------+----------+----------+
 |  Heaven |  357     |    354   |
 +-------------------------------+

After this patch:
 +---------+----------+----------+
 |         |  vGPU1   |   vGPU2  |
 +---------+----------+----------+
 |  Heaven |  397     |    398   |
 +-------------------------------+

v2: Let need_reschedule protect by gvt-lock.
Signed-off-by: Ping Gao <ping.a.gao@intel.com>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

This patch decouple the time slice calculation and scheduler, let
other event be able to trigger scheduling without impact the
calculation for QoS.

v2: add only one new enum definition.
v3: fix typo.
Signed-off-by: Ping Gao <ping.a.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

Since cmd message have been recorded in trace, gvt_dbg_cmd isn't
necessary. This will reduce much of dmesg as gvt_dbg_cmd is repeated
on each workload.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

Currently gvt dmesg is so heavy at drm.debug=0x2 that guest and
host almost couldn't run on xengt.

This patch transfer these repeated messages into trace, so dmesg
is light at drm.debug=0x2, and user could get the target message through
trace event and trace filter.
Suggested-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

Clean up it as it is not used now.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

kernel hangcheck needs to check RING_INSTDONE and SC_INSTDONE registers'
state to know if hardware is still running. In GVT-g environment, we need
to emulate these registers changing for all the guests although they are
not render owner. Here we return the physical state for all the guests,
then if INSTDONE is changing guest can know hardware is still running
although its workload is pending.

Read INSTDONE isn't one correct way to know if guest trigger gfx reset,
especially with Linux guest, it will read ACTH first, then check INSTDONE
and SUBSLICE registers to check if hardware is still running, at last
trigger gfx reset when it finds all the registers is frozen. In Windows
guest, read INSTDONE usually happens when OS detect TDR.

With the difference between Windows and Linux guest, "disable_warn_untrack"
may let debug log run into wrong state(Linux guest trigger hangcheck
with no ACTHD changed, then check INSTDONE), but actually there is no TDR
happened.

The new policy is always WARN with untrack MMIO r/w. Bad effect is many
noisy untrack mmio warning logs exist when real TDR happen. Even so you can
control the log output or not by setting the debug mask bit.

v2: remove log in instdone_mmio_read
Suggested-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

Commit ab9da627906a ("drm/i915: make context status notifier head be
per engine") gives us a chance to inspect every single request. Then
we can eliminate unnecessary mmio switching for same vGPU. We only
need mmio switching for different VMs (including host).

This patch introduced a new general API intel_gvt_switch_mmio() to
replace the old intel_gvt_load/restore_render_mmio(). This function
can be further optimized for vGPU to vGPU switching.

To support individual ring switch, we track the owner who occupy
each ring. When another VM or host request a ring we do the mmio
context switching. Otherwise no need to switch the ring.

This optimization is very useful if only one guest has plenty of
workloads and the host is mostly idle. The best case is no mmio
switching will happen.

v2:
  o fix missing ring switch issue. (chuanxiao)
  o support individual ring switch.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Reviewed-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

The function intel_vgpu_submit_execlist could be more simpler. It
actually does:
  1) validate the submission. The first context must be valid,
     and all two must be privilege_access.
  2) submit valid contexts. The first one need emulate schedule_in.

We do not need a bitmap, valid desc copy valid_desc. Local variable
emulate_schedule_in also can be optimized out.

v2: dump desc content in err msg (Zhi Wang)
Signed-off-by: Changbin Du <changbin.du@intel.com>
Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

The gvt:gvt_command trace involve unnecessary overhead even this trace is
not enabled. We need improve it.

The kernel trace infrastructure provide a full api to define a trace event.
We should leverage them if possible. And one important thing is that a trace
point should store raw data but not format string.

This patch include two part work:
1) Refactor the gvt_command trace definition, including:
  o only store raw trace data.
  o use __dynamic_array() to declare a variable size buffer.
  o use __print_array() to format raw cmd data.
  o rename vm_id as vgpu_id.

2) Improve the trace invoking, including:
  o remove the cycles calculation for handler. We can get this data
    by any perf tool.
  o do not make a backup for raw cmd data which just doesn't make sense.

With this patch, this trace has no overhead if it is not enabled. And we are
trace style now.

The final output example:
  gvt workload 0-211   [000] ...1   120.555964: gvt_command: vgpu1 ring 0: buf_type 0, ip_gma e161e880, raw cmd {0x4000000}
  gvt workload 0-211   [000] ...1   120.556014: gvt_command: vgpu1 ring 0: buf_type 0, ip_gma e161e884, raw cmd {0x7a000004,0x1004000,0xe1511018,0x0,0x7d,0x0}
  gvt workload 0-211   [000] ...1   120.556062: gvt_command: vgpu1 ring 0: buf_type 0, ip_gma e161e89c, raw cmd {0x7a000004,0x140000,0x0,0x0,0x0,0x0}
  gvt workload 0-211   [000] ...1   120.556110: gvt_command: vgpu1 ring 0: buf_type 0, ip_gma e161e8b4, raw cmd {0x10400002,0xe1511018,0x0,0x7d}
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Currently the timer is armed for 1ms after the first use and is killed
immediately, dropping the forcewake as early as possible. However, for
very frequent operations the forcewake dance has a large impact on
latency and keeping the timer alive until we are idle is preferred. To
achieve this, if we call intel_uncore_forcewake_get whilst the timer is
alive (repeated use), then set a flag to restart the timer on expiry
rather than drop the forcewake usage count. The timer is racy, the
consequence of the race is to expire the timer earlier than is now
desired but does not impact on correct behaviour. The offset the race
slightly, we set the active flag again on intel_uncore_forcewake_put.

The effect should be to reduce the jitter of reacquiring the fw every
1ms on a busy system. However, the cost is to keep the timer alive for
an extra 1ms on a nearly idle system. We chose to incur the jitter
previously to keep the timer off for as much as possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526132209.14640-1-chris@chris-wilson.co.uk

We're currently deleting the GuC logs if the FW fails to load, but those
are still useful to understand why the loading failed. Keeping the
object around allows us to access them after driver load is completed.

v2: keep the object around instead of using kernel memory (chris)
    don't store the logs in the gpu_error struct (Chris)
    add a check on guc_log_level to avoid snapshotting empty logs

v3: use separate debugfs for error log (Chris)

v4: rebased

v5: clean up obj selection, move err_load inside guc_log, move err_load
    cleanup, rename functions (Michal)

v6: move obj back to intel_guc, move functions to intel_uc.c, don't
    clear obj on new GuC load, free object only if enable_guc_loading
    is set (Michal)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495475428-19295-1-git-send-email-daniele.ceraolospurio@intel.comReviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Tested-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Buffer based command transport can replace MMIO based mechanism.
It may be used to perform host-2-guc and guc-to-host communication.

Portions of this patch are based on work by:
 Michel Thierry <michel.thierry@intel.com>
 Robert Beckett <robert.beckett@intel.com>
 Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>

v2: use gem_object_pin_map (Chris)
    don't use DEBUG_RATELIMITED (Chris)
    don't track action stats (Chris)
    simplify next fence (Chris)
    use READ_ONCE (Chris)
    move blob allocation to new function (Chris)

v3: use static owner id (Daniele)
v4: but keep channel initialization generic (Daniele)
    and introduce owner_sub_id (Daniele)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526111326.87280-3-michal.wajdeczko@intel.com

In earlier patch 789a6251 we were enabling send function only
after successful init. For completeness, we should make sure
that we disable it on fini.

v2: don't group steps by submission flag (Chris)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526111326.87280-2-michal.wajdeczko@intel.com

This patch adds the following definition
- Bit mask for EDP_PWMGEN_BIT_COUNT and min/max cap
  register which only use bit 0:4
- Base frequency (27 MHz) for backlight PWM frequency
  generator.
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523223805.46372-5-puthik@chromium.org

There are some panel that
(1) does not support display backlight enable via AUX
(2) support display backlight adjustment via AUX
(3) support display backlight enable via eDP BL_ENABLE pin

The current driver required that (1) must be support to enable (2).
This patch drops that requirement.
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523223805.46372-2-puthik@chromium.org

We depend on intel_iommu_gfx_mapped for various workarounds, but that is
only available under an #ifdef CONFIG_INTEL_IOMMU. Refactor all the
cut-and-paste ifdefs to a common routine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170525121612.2190-1-chris@chris-wilson.co.ukReviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

As only GGTT vma may be permanently pinned and are always at the head of
the object's vma list, as soon as we seen a ppGTT vma we can stop
searching for any_vma_pinned().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170525072528.11185-1-chris@chris-wilson.co.ukReviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

BXT has a H/W issue with IOMMU which can lead to system hangs when
Aperture accesses are queued within the GAM behind GTT Accesses.

This patch avoids the condition by wrapping all GTT updates in stop_machine
and using a flushing read prior to restarting the machine.

The stop_machine guarantees no new Aperture accesses can begin while
the PTE writes are being emmitted. The flushing read ensures that
any following Aperture accesses cannot begin until the PTE writes
have been cleared out of the GAM's fifo.

Only FOLLOWING Aperture accesses need to be separated from in flight
PTE updates. PTE Writes may follow tightly behind already in flight
Aperture accesses, so no flushing read is required at the start of
a PTE update sequence.

This issue was reproduced by running
	igt/gem_readwrite and
	igt/gem_render_copy
simultaneously from different processes, each in a tight loop,
with INTEL_IOMMU enabled.

This patch was originally published as:
	drm/i915: Serialize GTT Updates on BXT

v2: Move bxt/iommu detection into static function
    Remove #ifdef CONFIG_INTEL_IOMMU protection
    Make function names more reflective of purpose
    Move flushing read into static function

v3: Tidy up for checkpatch.pl

Testcase: igt/gem_concurrent_blit
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: John Harrison <john.C.Harrison@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495641251-30022-1-git-send-email-jon.bloomfield@intel.comReviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Having just watched someone add a new value, 0x3, without realising that
the flags were bit values, I have come to appreciate the value in using
BIT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523103116.32239-1-chris@chris-wilson.co.ukReviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

The compiler doesn't always spot the guard that object is allocated on
the first pass, leading to:

drivers/gpu/drm/i915/selftests/i915_gem_context.c: warning: 'obj' may be used uninitialized in this function [-Wuninitialized]:  => 370:8

v2: Make it more obvious by setting obj to NULL on the first pass and
any later pass where we need to reallocate.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 791ff39a ("drm/i915: Live testing for context execution")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
c: <drm-intel-fixes@lists.freedesktop.org> # v4.12-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170523194412.1195-1-chris@chris-wilson.co.ukReviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

If port[0] is occupied and we're trying to dequeue request from
different context, we will inevitably hit BUG_ON in port_assign.
Let's skip it - similar to what we're doing in execlists counterpart.

Fixes: 77f0d0e9 ("drm/i915/execlists: Pack the count into the low bits of the port.request")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Wajdeczko <michal.wajdeczko@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523102400.9614-2-michal.winiarski@intel.comSigned-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Passing NULL ctx to request_alloc would lead to null-ptr-deref.

v2: Let's not replace the comment with a BUG_ON
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523102400.9614-1-michal.winiarski@intel.comSigned-off-by: Chris Wilson <chris@chris-wilson.co.uk>

We improved the reset reliablity on gen4 with
stopping all engines before commencing reset, in
commit 2c80353f ("drm/i915/g4x: Improve gpu reset reliability")

Evidence indicates that this same trick works with g33.

v2: proper gen naming, comment readability (Chris)

Testcase: igt/gem_busy/*-hang #blb-e6850
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170522090244.2557-1-mika.kuoppala@intel.com

This reverts commit bc5ca47c.

Gabriel put this back into generic code with

commit 75f6dfe3
Author: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Date:   Wed Dec 28 12:32:11 2016 -0200

    drm: Deduplicate driver initialization message

but somehow he missed Chris' patch to add the message meanwhile.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101025
Fixes: 75f6dfe3 ("drm: Deduplicate driver initialization message")
Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v4.11+
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517131557.7836-1-daniel.vetter@ffwll.ch

Update version of HuC from 01.07.1748 to the
version 02.00.1748

Cc: Ander Conselvan <ander.conselvan.de.oliveira@intel.com>
Cc: John Spotswood <john.a.spotswood@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495129631-2930-1-git-send-email-anusha.srivatsa@intel.com

The memory allocation for C is not being null checked and hence we
could end up with a null pointer dereference. Fix this with a null
pointer check. (I really should have noticed this when I was fixing an
earlier issue.)

Detected by CoverityScan, CID#1436406 ("Dereference null return")

Fixes: 47624cc3 ("drm/i915: Import the kfence selftests for i915_sw_fence")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519175617.7036-1-colin.king@canonical.comReviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Usefulness of these stats was over-advertised.

v2: remove duplicated engine stats (Chris)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170515170610.35528-1-michal.wajdeczko@intel.comAcked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

ELK seems to very picky about the preconditions to reset.
Evidence on Eaglelake (8086:2e12 (rev 03)) shows that it does
not like if reset occurs when there is active ring.

Ville found out that there is workaround with name
'WaMediaResetMainRingCleanup' which suggests that we need to
cleanup rings before resetting. It is unclear what cleanup
exactly means but evidence shows that stopping the ring
does have an effect on reset reliability. This patch makes
reset successful on hangs induced by chained batches (the igt ones).
Note that if the hang is inside a shader, it is possible
that our attempts to stop the ring achieves anything.

v2: zero ctl,head,tail also. bug ref. use driver debugs (Chris)
v3: specify platform on testcases, comment tidyup (Chris)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100942
Testcase: igt/gem_busy/*-hang #elk
Testcase: igt/gem_ringfill/hang-* #elk
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519091340.21439-1-mika.kuoppala@intel.com

Debugfs does not seems to be a right place to display transient data.
If we want to capture errors, we should log them.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170518113104.54400-3-michal.wajdeczko@intel.comReviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

This stat is almost always zero unless fatal error occurs,
which should be reported by other means anyway.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170518113104.54400-2-michal.wajdeczko@intel.comReviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

This member was dropped long time ago.

Fixes: 774439e1 ("drm/i915/guc: re-optimise i915_guc_client layout")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170518113104.54400-1-michal.wajdeczko@intel.comReviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Ville found a reference to WaMediaResetBeforeFullReset which we presume
means that we should simply do the media reset first.

References: https://bugs.freedesktop.org/show_bug.cgi?id=100942Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170518204811.7408-2-chris@chris-wilson.co.uk

Repeat the reset a couple of times if at first we do not succeed.

v2: differentiate which path/engine failed with a debug message
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170513083726.502-1-chris@chris-wilson.co.ukReviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170518204811.7408-1-chris@chris-wilson.co.uk

Set the class on our mock pci device to GFX. This should be useful for
utilities like intel-iommu that special case gfx devices.

References: https://bugs.freedesktop.org/show_bug.cgi?id=101080Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170518094638.5469-1-chris@chris-wilson.co.ukReviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>