- 16 Aug, 2017 12 commits
-
-
Sandeep Singh authored
commit e788787e upstream. Certain HP keyboards would keep inputting a character automatically which is the wake-up key after S3 resume On some AMD platforms USB host fails to respond (by holding resume-K) to USB device (an HP keyboard) resume request within 1ms (TURSM) and ensures that resume is signaled for at least 20 ms (TDRSMDN), which is defined in USB 2.0 spec. The result is that the keyboard is out of function. In SNPS USB design, the host responds to the resume request only after system gets back to S0 and the host gets to functional after the internal HW restore operation that is more than 1 second after the initial resume request from the USB device. As a workaround for specific keyboard ID(HP Keyboards), applying port reset after resume when the keyboard is plugged in. Signed-off-by:
Sandeep Singh <Sandeep.Singh@amd.com> Signed-off-by:
Shyam Sundar S K <Shyam-sundar.S-k@amd.com> cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Reviewed-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Kai-Heng Feng authored
commit 7496cfe5 upstream. Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to connect to Realtek r8153. The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk can make it work. Since another r8153 dongle at my hand does not have the issue, so add the quirk to the Genesys Logic hub instead. Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
-
Alan Stern authored
commit 94c43b98 upstream. Some buggy USB disk adapters disconnect and reconnect multiple times during the enumeration procedure. This may lead to a device connecting at full speed instead of high speed, because when the USB stack sees that a device isn't able to enumerate at high speed, it tries to hand the connection over to a full-speed companion controller. The logic for doing this is careful to check that the device is still connected. But this check is inadequate if the device disconnects and reconnects before the check is done. The symptom is that a device works, but much more slowly than it is capable of operating. The situation was made worse recently by commit 22547c4c ("usb: hub: Wait for connection to be reestablished after port reset"), which increases the delay following a reset before a disconnect is recognized, thus giving the device more time to reconnect. This patch makes the check more robust. If the device was disconnected at any time during enumeration, we will now skip the full-speed handover. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by:
Zdenek Kabelac <zkabelac@redhat.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Alan Swanson authored
commit 89f23d51 upstream. Similar to commit d595259f ("usb-storage: Add ignore-residue quirk for Initio INIC-3619") for INIC-3169 in unusual_devs.h but INIC-3069 already present in unusual_uas.h. Both in same controller IC family. Issue is that MakeMKV fails during key exchange with installed bluray drive with following error: 002004:0000 Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED' occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:0' Signed-off-by:
Alan Swanson <reiver@improbability.net> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Akinobu Mita authored
commit a3507e48 upstream. The TSL2563 driver provides three iio channels, two of which are raw ADC channels (channel 0 and channel 1) in the device and the remaining one is calculated by the two. The ADC channel 0 only supports programmable interrupt with threshold settings and this driver supports the event but the generated event code does not contain the corresponding iio channel type. This is going to change userspace ABI. Hopefully fixing this to be what it should always have been won't break any userspace code. Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Arnd Bergmann authored
commit 105967ad upstream. gcc-7 points out an older regression: drivers/staging/iio/resolver/ad2s1210.c: In function 'ad2s1210_read_raw': drivers/staging/iio/resolver/ad2s1210.c:515:42: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context] The original code had 'unsigned short' here, but incorrectly got converted to 'bool'. This reverts the regression and uses a normal type instead. Fixes: 29148543 ("staging:iio:resolver:ad2s1210 minimal chan spec conversion.") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit cd5a6a4f upstream. Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for the primary one. Among other thigs, this prevents check_root_hub_suspended() from returning -EBUSY for dead HCDs which helps to work around system suspend issues in some situations. This actually fixes occasional suspend failures on one of my test machines. Suggested-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by:
-
Bin Liu authored
commit 45d73860 upstream. commit 68fe05e2 ("usb: musb: fix tx fifo flush handling") drops the 1ms delay trying to solve the long disconnect time issue when application queued many tx urbs. However, the 1ms delay is needed for some use cases, for example, without the delay, reconnecting AR9271 WIFI dongle no longer works if the connection is dropped from the AP. So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the long disconnect time problem with a separate patch for usb_hcd_flush_endpoint(). Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
Stefan Triller authored
commit 9585e340 upstream. The German Telekom offers a ZigBee USB Stick under the brand name Qivicon for their SmartHome Home Base in its 1. Generation. The productId is not known by the according kernel module, this patch adds support for it. Signed-off-by:
Stefan Triller <github@stefantriller.de> Reviewed-by:
Frans Klaver <fransklaver@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Hector Martin authored
commit fd1b8668 upstream. Add device id for D-Link DWM-222. Signed-off-by:
Hector Martin <marcan@marcan.st> Signed-off-by:
-
Mateusz Jurczyk authored
commit 68227c03 upstream. Before the patch, the flock flag could remain uninitialized for the lifespan of the fuse_file allocation. Unless set to true in fuse_file_flock(), it would remain in an indeterminate state until read in an if statement in fuse_release_common(). This could consequently lead to taking an unexpected branch in the code. The bug was discovered by a runtime instrumentation designed to detect use of uninitialized memory in the kernel. Signed-off-by:
Mateusz Jurczyk <mjurczyk@google.com> Fixes: 37fb3a30 ("fuse: fix flock") Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Jonathan Toppins authored
commit 75dddef3 upstream. The RDMA subsystem can generate several thousand of these messages per second eventually leading to a kernel crash. Ratelimit these messages to prevent this crash. Doug said: "I've been carrying a version of this for several kernel versions. I don't remember when they started, but we have one (and only one) class of machines: Dell PE R730xd, that generate these errors. When it happens, without a rate limit, we get rcu timeouts and kernel oopses. With the rate limit, we just get a lot of annoying kernel messages but the machine continues on, recovers, and eventually the memory operations all succeed" And: "> Well... why are all these EBUSY's occurring? It sounds inefficient > (at least) but if it is expected, normal and unavoidable then > perhaps we should just remove that message altogether? I don't have an answer to that question. To be honest, I haven't looked real hard. We never had this at all, then it started out of the blue, but only on our Dell 730xd machines (and it hits all of them), but no other classes or brands of machines. And we have our 730xd machines loaded up with different brands and models of cards (for instance one dedicated to mlx4 hardware, one for qib, one for mlx5, an ocrdma/cxgb4 combo, etc), so the fact that it hit all of the machines meant it wasn't tied to any particular brand/model of RDMA hardware. To me, it always smelled of a hardware oddity specific to maybe the CPUs or mainboard chipsets in these machines, so given that I'm not an mm expert anyway, I never chased it down. A few other relevant details: it showed up somewhere around 4.8/4.9 or thereabouts. It never happened before, but the prinkt has been there since the 3.18 days, so possibly the test to trigger this message was changed, or something else in the allocator changed such that the situation started happening on these machines? And, like I said, it is specific to our 730xd machines (but they are all identical, so that could mean it's something like their specific ram configuration is causing the allocator to hit this on these machine but not on other machines in the cluster, I don't want to say it's necessarily the model of chipset or CPU, there are other bits of identicalness between these machines)" Link: http://lkml.kernel.org/r/499c0f6cc10d6eb829a67f2a4d75b4228a9b356e.1501695897.git.jtoppins@redhat.comSigned-off-by:
Jonathan Toppins <jtoppins@redhat.com> Reviewed-by:
Doug Ledford <dledford@redhat.com> Tested-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
- 13 Aug, 2017 10 commits
-
-
Greg Kroah-Hartman authored
-
zheng li authored
ipv4: Should use consistent conditional judgement for ip fragment in __ip_append_data and ip_finish_output commit 0a28cfd5 upstream. There is an inconsistent conditional judgement in __ip_append_data and ip_finish_output functions, the variable length in __ip_append_data just include the length of application's payload and udp header, don't include the length of ip header, but in ip_finish_output use (skb->len > ip_skb_dst_mtu(skb)) as judgement, and skb->len include the length of ip header. That causes some particular application's udp payload whose length is between (MTU - IP Header) and MTU were fragmented by ip_fragment even though the rst->dev support UFO feature. Add the length of ip header to length in __ip_append_data to keep consistent conditional judgement as ip_finish_output for ip fragment. Signed-off-by:
Zheng Li <james.z.li@ericsson.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit 85f1bd9a ] When iteratively building a UDP datagram with MSG_MORE and that datagram exceeds MTU, consistently choose UFO or fragmentation. Once skb_is_gso, always apply ufo. Conversely, once a datagram is split across multiple skbs, do not consider ufo. Sendpage already maintains the first invariant, only add the second. IPv6 does not have a sendpage implementation to modify. A gso skb must have a partial checksum, do not follow sk_no_check_tx in udp_send_skb. Found by syzkaller. [gregkh - tweaks for 3.18 for ipv6, hopefully they are correct...] Fixes: e89e9cf5 ("[IPv4/IPv6]: UFO Scatter-gather approach") Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Greg Kroah-Hartman authored
revert "ipv4: Should use consistent conditional judgement for ip fragment in __ip_append_data and ip_finish_output" This reverts commit f102bb71 which is commit 0a28cfd5 upstream as there is another patch that needs to be applied instead of this one. Cc: Zheng Li <james.z.li@ericsson.com> Cc: David S. Miller <davem@davemloft.net> Cc: Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit c27927e3 ] Updates to tp_reserve can race with reads of the field in packet_set_ring. Avoid this by holding the socket lock during updates in setsockopt PACKET_RESERVE. This bug was discovered by syzkaller. Fixes: 8913336a ("packet: add PACKET_RESERVE sockopt") Reported-by:
-
Willem de Bruijn authored
[ Upstream commit 8d63bee6 ] skb_warn_bad_offload triggers a warning when an skb enters the GSO stack at __skb_gso_segment that does not have CHECKSUM_PARTIAL checksum offload set. Commit b2504a5d ("net: reduce skb_warn_bad_offload() noise") observed that SKB_GSO_DODGY producers can trigger the check and that passing those packets through the GSO handlers will fix it up. But, the software UFO handler will set ip_summed to CHECKSUM_NONE. When __skb_gso_segment is called from the receive path, this triggers the warning again. Make UFO set CHECKSUM_UNNECESSARY instead of CHECKSUM_NONE. On Tx these two are equivalent. On Rx, this better matches the skb state (checksum computed), as CHECKSUM_NONE here means no checksum computed. See also this thread for context: http://patchwork.ozlabs.org/patch/799015/ Fixes: b2504a5d ("net: reduce skb_warn_bad_offload() noise") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 8ba60924 ] With new TCP_FASTOPEN_CONNECT socket option, there is a possibility to call tcp_connect() while socket sk_dst_cache is either NULL or invalid. +0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 4 +0 fcntl(4, F_SETFL, O_RDWR|O_NONBLOCK) = 0 +0 setsockopt(4, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0 +0 connect(4, ..., ...) = 0 << sk->sk_dst_cache becomes obsolete, or even set to NULL >> +1 sendto(4, ..., 1000, MSG_FASTOPEN, ..., ...) = 1000 We need to refresh the route otherwise bad things can happen, especially when syzkaller is running on the host :/ Fixes: 19f6d3f3 ("net/tcp-fastopen: Add new API support") Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Wei Wang <weiwan@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by:
Wei Wang <weiwan@google.com> Acked-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 96d97030 ] Commit 55917a21 ("netfilter: x_tables: add context to know if extension runs from nft_compat") introduced a member nft_compat to xt_tgchk_param structure. But it didn't set it's value for ipt_init_target. With unexpected value in par.nft_compat, it may return unexpected result in some target's checkentry. This patch is to set all it's fields as 0 and only initialize the non-zero fields in ipt_init_target. v1->v2: As Wang Cong's suggestion, fix it by setting all it's fields as 0 and only initializing the non-zero fields. Fixes: 55917a21 ("netfilter: x_tables: add context to know if extension runs from nft_compat") Suggested-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 2dda6400 ] syzkaller was able to trigger a divide by 0 in TCP stack [1] Issue here is that keepalive timer needs to be updated to not attempt to send a probe if the connection setup was deferred using TCP_FASTOPEN_CONNECT socket option added in linux-4.11 [1] divide error: 0000 [#1] SMP CPU: 18 PID: 0 Comm: swapper/18 Not tainted task: ffff986f62f4b040 ti: ffff986f62fa2000 task.ti: ffff986f62fa2000 RIP: 0010:[<ffffffff8409cc0d>] [<ffffffff8409cc0d>] __tcp_select_window+0x8d/0x160 Call Trace: <IRQ> [<ffffffff8409d951>] tcp_transmit_skb+0x11/0x20 [<ffffffff8409da21>] tcp_xmit_probe_skb+0xc1/0xe0 [<ffffffff840a0ee8>] tcp_write_wakeup+0x68/0x160 [<ffffffff840a151b>] tcp_keepalive_timer+0x17b/0x230 [<ffffffff83b3f799>] call_timer_fn+0x39/0xf0 [<ffffffff83b40797>] run_timer_softirq+0x1d7/0x280 [<ffffffff83a04ddb>] __do_softirq+0xcb/0x257 [<ffffffff83ae03ac>] irq_exit+0x9c/0xb0 [<ffffffff83a04c1a>] smp_apic_timer_interrupt+0x6a/0x80 [<ffffffff83a03eaf>] apic_timer_interrupt+0x7f/0x90 <EOI> [<ffffffff83fed2ea>] ? cpuidle_enter_state+0x13a/0x3b0 [<ffffffff83fed2cd>] ? cpuidle_enter_state+0x11d/0x3b0 Tested: Following packetdrill no longer crashes the kernel `echo 0 >/proc/sys/net/ipv4/tcp_timestamps` // Cache warmup: send a Fast Open cookie request 0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3 +0 fcntl(3, F_SETFL, O_RDWR|O_NONBLOCK) = 0 +0 setsockopt(3, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0 +0 connect(3, ..., ...) = -1 EINPROGRESS (Operation is now in progress) +0 > S 0:0(0) <mss 1460,nop,nop,sackOK,nop,wscale 8,FO,nop,nop> +.01 < S. 123:123(0) ack 1 win 14600 <mss 1460,nop,nop,sackOK,nop,wscale 6,FO abcd1234,nop,nop> +0 > . 1:1(0) ack 1 +0 close(3) = 0 +0 > F. 1:1(0) ack 1 +0 < F. 1:1(0) ack 2 win 92 +0 > . 2:2(0) ack 2 +0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 4 +0 fcntl(4, F_SETFL, O_RDWR|O_NONBLOCK) = 0 +0 setsockopt(4, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0 +0 setsockopt(4, SOL_SOCKET, SO_KEEPALIVE, [1], 4) = 0 +.01 connect(4, ..., ...) = 0 +0 setsockopt(4, SOL_TCP, TCP_KEEPIDLE, [5], 4) = 0 +10 close(4) = 0 `echo 1 >/proc/sys/net/ipv4/tcp_timestamps` Fixes: 19f6d3f3 ("net/tcp-fastopen: Add new API support") Signed-off-by:
-
Yuchung Cheng authored
[ Upstream commit ed254971 ] If the sender switches the congestion control during ECN-triggered cwnd-reduction state (CA_CWR), upon exiting recovery cwnd is set to the ssthresh value calculated by the previous congestion control. If the previous congestion control is BBR that always keep ssthresh to TCP_INIFINITE_SSTHRESH, cwnd ends up being infinite. The safe step is to avoid assigning invalid ssthresh value when recovery ends. Signed-off-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
-
- 11 Aug, 2017 18 commits
-
-
Greg Kroah-Hartman authored
-
Tejun Heo authored
commit 0a94efb5 upstream. 5c0338c6 ("workqueue: restore WQ_UNBOUND/max_active==1 to be ordered") automatically enabled ordered attribute for unbound workqueues w/ max_active == 1. Because ordered workqueues reject max_active and some attribute changes, this implicit ordered mode broke cases where the user creates an unbound workqueue w/ max_active == 1 and later explicitly changes the related attributes. This patch distinguishes explicit and implicit ordered setting and overrides from attribute changes if implict. Signed-off-by:
Tejun Heo <tj@kernel.org> Fixes: 5c0338c6 ("workqueue: restore WQ_UNBOUND/max_active==1 to be ordered") Cc: Holger Hoffstätte <holger@applied-asynchrony.com> Signed-off-by:
-
Florian Fainelli authored
commit 7b9a88a3 upstream. The PHY library does not deal very well with bind and unbind events. The first thing we would see is that we were not properly canceling the PHY state machine workqueue, so we would be crashing while dereferencing phydev->drv since there is no driver attached anymore. Suggested-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
zheng li authored
ipv4: Should use consistent conditional judgement for ip fragment in __ip_append_data and ip_finish_output [ Upstream commit 0a28cfd5 ] There is an inconsistent conditional judgement in __ip_append_data and ip_finish_output functions, the variable length in __ip_append_data just include the length of application's payload and udp header, don't include the length of ip header, but in ip_finish_output use (skb->len > ip_skb_dst_mtu(skb)) as judgement, and skb->len include the length of ip header. That causes some particular application's udp payload whose length is between (MTU - IP Header) and MTU were fragmented by ip_fragment even though the rst->dev support UFO feature. Add the length of ip header to length in __ip_append_data to keep consistent conditional judgement as ip_finish_output for ip fragment. Signed-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
-
Ard Biesheuvel authored
[ Upstream commit f073bdc5 ] The VM_BUG_ON() check in move_freepages() checks whether the node id of a page matches the node id of its zone. However, it does this before having checked whether the struct page pointer refers to a valid struct page to begin with. This is guaranteed in most cases, but may not be the case if CONFIG_HOLES_IN_ZONE=y. So reorder the VM_BUG_ON() with the pfn_valid_within() check. Link: http://lkml.kernel.org/r/1481706707-6211-2-git-send-email-ard.biesheuvel@linaro.orgSigned-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by:
Will Deacon <will.deacon@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Hanjun Guo <hanjun.guo@linaro.org> Cc: Yisheng Xie <xieyisheng1@huawei.com> Cc: Robert Richter <rrichter@cavium.com> Cc: James Morse <james.morse@arm.com> Signed-off-by:
-
Jamie Iles authored
[ Upstream commit 2d39b3cd ] Since commit 00cd5c37 ("ptrace: permit ptracing of /sbin/init") we can now trace init processes. init is initially protected with SIGNAL_UNKILLABLE which will prevent fatal signals such as SIGSTOP, but there are a number of paths during tracing where SIGNAL_UNKILLABLE can be implicitly cleared. This can result in init becoming stoppable/killable after tracing. For example, running: while true; do kill -STOP 1; done & strace -p 1 and then stopping strace and the kill loop will result in init being left in state TASK_STOPPED. Sending SIGCONT to init will resume it, but init will now respond to future SIGSTOP signals rather than ignoring them. Make sure that when setting SIGNAL_STOP_CONTINUED/SIGNAL_STOP_STOPPED that we don't clear SIGNAL_UNKILLABLE. Link: http://lkml.kernel.org/r/20170104122017.25047-1-jamie.iles@oracle.comSigned-off-by:
Jamie Iles <jamie.iles@oracle.com> Acked-by:
Oleg Nesterov <oleg@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by:
-
Sudip Mukherjee authored
[ Upstream commit da0510c4 ] The build of frv allmodconfig was failing with the errors like: /tmp/cc0JSPc3.s: Assembler messages: /tmp/cc0JSPc3.s:1839: Error: symbol `.LSLT0' is already defined /tmp/cc0JSPc3.s:1842: Error: symbol `.LASLTP0' is already defined /tmp/cc0JSPc3.s:1969: Error: symbol `.LELTP0' is already defined /tmp/cc0JSPc3.s:1970: Error: symbol `.LELT0' is already defined Commit 866ced95 ("kbuild: Support split debug info v4") introduced splitting the debug info and keeping that in a separate file. Somehow, the frv-linux gcc did not like that and I am guessing that instead of splitting it started copying. The first report about this is at: https://lists.01.org/pipermail/kbuild-all/2015-July/010527.html. I will try and see if this can work with frv and if still fails I will open a bug report with gcc. But meanwhile this is the easiest option to solve build failure of frv. Fixes: 866ced95 ("kbuild: Support split debug info v4") Link: http://lkml.kernel.org/r/1482062348-5352-1-git-send-email-sudipm.mukherjee@gmail.comSigned-off-by:
Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: David Howells <dhowells@redhat.com> Signed-off-by:
-
Michal Hocko authored
[ Upstream commit bb1107f7 ] Andrey Konovalov has reported the following warning triggered by the syzkaller fuzzer. WARNING: CPU: 1 PID: 9935 at mm/page_alloc.c:3511 __alloc_pages_nodemask+0x159c/0x1e20 Kernel panic - not syncing: panic_on_warn set ... CPU: 1 PID: 9935 Comm: syz-executor0 Not tainted 4.9.0-rc7+ #34 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __alloc_pages_slowpath mm/page_alloc.c:3511 __alloc_pages_nodemask+0x159c/0x1e20 mm/page_alloc.c:3781 alloc_pages_current+0x1c7/0x6b0 mm/mempolicy.c:2072 alloc_pages include/linux/gfp.h:469 kmalloc_order+0x1f/0x70 mm/slab_common.c:1015 kmalloc_order_trace+0x1f/0x160 mm/slab_common.c:1026 kmalloc_large include/linux/slab.h:422 __kmalloc+0x210/0x2d0 mm/slub.c:3723 kmalloc include/linux/slab.h:495 ep_write_iter+0x167/0xb50 drivers/usb/gadget/legacy/inode.c:664 new_sync_write fs/read_write.c:499 __vfs_write+0x483/0x760 fs/read_write.c:512 vfs_write+0x170/0x4e0 fs/read_write.c:560 SYSC_write fs/read_write.c:607 SyS_write+0xfb/0x230 fs/read_write.c:599 entry_SYSCALL_64_fastpath+0x1f/0xc2 The issue is caused by a lack of size check for the request size in ep_write_iter which should be fixed. It, however, points to another problem, that SLUB defines KMALLOC_MAX_SIZE too large because the its KMALLOC_SHIFT_MAX is (MAX_ORDER + PAGE_SHIFT) which means that the resulting page allocator request might be MAX_ORDER which is too large (see __alloc_pages_slowpath). The same applies to the SLOB allocator which allows even larger sizes. Make sure that they are capped properly and never request more than MAX_ORDER order. Link: http://lkml.kernel.org/r/20161220130659.16461-2-mhocko@kernel.orgSigned-off-by:
Michal Hocko <mhocko@suse.com> Reported-by:
Christoph Lameter <cl@linux.com> Cc: Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Rabin Vincent authored
[ Upstream commit 270c8cf1 ] ARM has a few system calls (most notably mmap) for which the names of the functions which are referenced in the syscall table do not match the names of the syscall tracepoints. As a consequence of this, these tracepoints are not made available. Implement arch_syscall_match_sym_name to fix this and allow tracing even these system calls. Signed-off-by:
Rabin Vincent <rabinv@axis.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Milan P. Gandhi authored
[ Upstream commit c7702b8c ] There is a race condition with qla2xxx optrom functions where one thread might modify optrom buffer, optrom_state while other thread is still reading from it. In couple of crashes, it was found that we had successfully passed the following 'if' check where we confirm optrom_state to be QLA_SREADING. But by the time we acquired mutex lock to proceed with memory_read_from_buffer function, some other thread/process had already modified that option rom buffer and optrom_state from QLA_SREADING to QLA_SWAITING. Then we got ha->optrom_buffer 0x0 and crashed the system: if (ha->optrom_state != QLA_SREADING) return 0; mutex_lock(&ha->optrom_mutex); rval = memory_read_from_buffer(buf, count, &off, ha->optrom_buffer, ha->optrom_region_size); mutex_unlock(&ha->optrom_mutex); With current optrom function we get following crash due to a race condition: [ 1479.466679] BUG: unable to handle kernel NULL pointer dereference at (null) [ 1479.466707] IP: [<ffffffff81326756>] memcpy+0x6/0x110 [...] [ 1479.473673] Call Trace: [ 1479.474296] [<ffffffff81225cbc>] ? memory_read_from_buffer+0x3c/0x60 [ 1479.474941] [<ffffffffa01574dc>] qla2x00_sysfs_read_optrom+0x9c/0xc0 [qla2xxx] [ 1479.475571] [<ffffffff8127e76b>] read+0xdb/0x1f0 [ 1479.476206] [<ffffffff811fdf9e>] vfs_read+0x9e/0x170 [ 1479.476839] [<ffffffff811feb6f>] SyS_read+0x7f/0xe0 [ 1479.477466] [<ffffffff816964c9>] system_call_fastpath+0x16/0x1b Below patch modifies qla2x00_sysfs_read_optrom, qla2x00_sysfs_write_optrom functions to get the mutex_lock before checking ha->optrom_state to avoid similar crashes. The patch was applied and tested and same crashes were no longer observed again. Tested-by:
Milan P. Gandhi <mgandhi@redhat.com> Signed-off-by:
Laurence Oberman <loberman@redhat.com> Acked-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Nicholas Mc Guire authored
[ Upstream commit fac69d0e ] Add the missing declarations of basic string functions to string.h to allow a clean build. Fixes: 5be86566 ("String-handling functions for the new x86 setup code.") Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Link: http://lkml.kernel.org/r/1483781911-21399-1-git-send-email-hofrat@osadl.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Michael Chan authored
[ Upstream commit f5992b72 ] The driver's ndo_get_stats64() method is not always called under RTNL. So it can race with driver close or ethtool reconfigurations. Fix the race condition by taking tp->lock spinlock in tg3_free_consistent() when freeing the tp->hw_stats memory block. tg3_get_stats64() is already taking tp->lock. Reported-by:
Wang Yufen <wangyufen@huawei.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Sergei Shtylyov authored
[ Upstream commit 0f1f9cbc ] The R8A7740 GEther controller supports the packet checksum offloading but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740 data, thus CSMR isn't cleared... Fixes: 73a0d907 ("net: sh_eth: add support R8A7740") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Arnd Bergmann authored
commit 93be2b74 upstream. gcc-7 complains that wl3501_cs passes NULL into a function that then uses the argument as the input for memcpy: drivers/net/wireless/wl3501_cs.c: In function 'wl3501_get_scan': include/net/iw_handler.h:559:3: error: argument 2 null where non-null expected [-Werror=nonnull] memcpy(stream + point_len, extra, iwe->u.data.length); This works fine here because iwe->u.data.length is guaranteed to be 0 and the memcpy doesn't actually have an effect. Making the length check explicit avoids the warning and should have no other effect here. Also check the pointer itself, since otherwise we get warnings elsewhere in the code. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Wei Liu authored
[ Upstream commit dfa523ae ] Add a flag to indicate if a queue is rate-limited. Test the flag in NAPI poll handler and avoid rescheduling the queue if true, otherwise we risk locking up the host. The rescheduling will be done in the timer callback function. Reported-by:
Jean-Louis Dupond <jean-louis@dupond.be> Signed-off-by:
Wei Liu <wei.liu2@citrix.com> Tested-by:
Paul Durrant <paul.durrant@citrix.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 7ad813f2 ] Marc reported that he was not getting the PHY library adjust_link() callback function to run when calling phy_stop() + phy_disconnect() which does not indeed happen because we set the state machine to PHY_HALTED but we don't get to run it to process this state past that point. Fix this with a synchronous call to phy_state_machine() in order to have the state machine actually act on PHY_HALTED, set the PHY device's link down, turn the network device's carrier off and finally call the adjust_link() function. Reported-by:
Marc Gonzalez <marc_gonzalez@sigmadesigns.com> Fixes: a390d1f3 ("phylib: convert state_queue work to delayed_work") Signed-off-by:
-
Xin Long authored
[ Upstream commit 6b84202c ] Commit b1f5bfc2 ("sctp: don't dereference ptr before leaving _sctp_walk_{params, errors}()") tried to fix the issue that it may overstep the chunk end for _sctp_walk_{params, errors} with 'chunk_end > offset(length) + sizeof(length)'. But it introduced a side effect: When processing INIT, it verifies the chunks with 'param.v == chunk_end' after iterating all params by sctp_walk_params(). With the check 'chunk_end > offset(length) + sizeof(length)', it would return when the last param is not yet accessed. Because the last param usually is fwdtsn supported param whose size is 4 and 'chunk_end == offset(length) + sizeof(length)' This is a badly issue even causing sctp couldn't process 4-shakes. Client would always get abort when connecting to server, due to the failure of INIT chunk verification on server. The patch is to use 'chunk_end <= offset(length) + sizeof(length)' instead of 'chunk_end < offset(length) + sizeof(length)' for both _sctp_walk_params and _sctp_walk_errors. Fixes: b1f5bfc2 ("sctp: don't dereference ptr before leaving _sctp_walk_{params, errors}()") Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Alexander Potapenko authored
[ Upstream commit b1f5bfc2 ] If the length field of the iterator (|pos.p| or |err|) is past the end of the chunk, we shouldn't access it. This bug has been detected by KMSAN. For the following pair of system calls: socket(PF_INET6, SOCK_STREAM, 0x84 /* IPPROTO_??? */) = 3 sendto(3, "A", 1, MSG_OOB, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = 1 the tool has reported a use of uninitialized memory: ================================================================== BUG: KMSAN: use of uninitialized memory in sctp_rcv+0x17b8/0x43b0 CPU: 1 PID: 2940 Comm: probe Not tainted 4.11.0-rc5+ #2926 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:16 dump_stack+0x172/0x1c0 lib/dump_stack.c:52 kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:927 __msan_warning_32+0x61/0xb0 mm/kmsan/kmsan_instr.c:469 __sctp_rcv_init_lookup net/sctp/input.c:1074 __sctp_rcv_lookup_harder net/sctp/input.c:1233 __sctp_rcv_lookup net/sctp/input.c:1255 sctp_rcv+0x17b8/0x43b0 net/sctp/input.c:170 sctp6_rcv+0x32/0x70 net/sctp/ipv6.c:984 ip6_input_finish+0x82f/0x1ee0 net/ipv6/ip6_input.c:279 NF_HOOK ./include/linux/netfilter.h:257 ip6_input+0x239/0x290 net/ipv6/ip6_input.c:322 dst_input ./include/net/dst.h:492 ip6_rcv_finish net/ipv6/ip6_input.c:69 NF_HOOK ./include/linux/netfilter.h:257 ipv6_rcv+0x1dbd/0x22e0 net/ipv6/ip6_input.c:203 __netif_receive_skb_core+0x2f6f/0x3a20 net/core/dev.c:4208 __netif_receive_skb net/core/dev.c:4246 process_backlog+0x667/0xba0 net/core/dev.c:4866 napi_poll net/core/dev.c:5268 net_rx_action+0xc95/0x1590 net/core/dev.c:5333 __do_softirq+0x485/0x942 kernel/softirq.c:284 do_softirq_own_stack+0x1c/0x30 arch/x86/entry/entry_64.S:902 </IRQ> do_softirq kernel/softirq.c:328 __local_bh_enable_ip+0x25b/0x290 kernel/softirq.c:181 local_bh_enable+0x37/0x40 ./include/linux/bottom_half.h:31 rcu_read_unlock_bh ./include/linux/rcupdate.h:931 ip6_finish_output2+0x19b2/0x1cf0 net/ipv6/ip6_output.c:124 ip6_finish_output+0x764/0x970 net/ipv6/ip6_output.c:149 NF_HOOK_COND ./include/linux/netfilter.h:246 ip6_output+0x456/0x520 net/ipv6/ip6_output.c:163 dst_output ./include/net/dst.h:486 NF_HOOK ./include/linux/netfilter.h:257 ip6_xmit+0x1841/0x1c00 net/ipv6/ip6_output.c:261 sctp_v6_xmit+0x3b7/0x470 net/sctp/ipv6.c:225 sctp_packet_transmit+0x38cb/0x3a20 net/sctp/output.c:632 sctp_outq_flush+0xeb3/0x46e0 net/sctp/outqueue.c:885 sctp_outq_uncork+0xb2/0xd0 net/sctp/outqueue.c:750 sctp_side_effects net/sctp/sm_sideeffect.c:1773 sctp_do_sm+0x6962/0x6ec0 net/sctp/sm_sideeffect.c:1147 sctp_primitive_ASSOCIATE+0x12c/0x160 net/sctp/primitive.c:88 sctp_sendmsg+0x43e5/0x4f90 net/sctp/socket.c:1954 inet_sendmsg+0x498/0x670 net/ipv4/af_inet.c:762 sock_sendmsg_nosec net/socket.c:633 sock_sendmsg net/socket.c:643 SYSC_sendto+0x608/0x710 net/socket.c:1696 SyS_sendto+0x8a/0xb0 net/socket.c:1664 do_syscall_64+0xe6/0x130 arch/x86/entry/common.c:285 entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.S:246 RIP: 0033:0x401133 RSP: 002b:00007fff6d99cd38 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00000000004002b0 RCX: 0000000000401133 RDX: 0000000000000001 RSI: 0000000000494088 RDI: 0000000000000003 RBP: 00007fff6d99cd90 R08: 00007fff6d99cd50 R09: 000000000000001c R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000000 R13: 00000000004063d0 R14: 0000000000406460 R15: 0000000000000000 origin: save_stack_trace+0x37/0x40 arch/x86/kernel/stacktrace.c:59 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:302 kmsan_internal_poison_shadow+0xb1/0x1a0 mm/kmsan/kmsan.c:198 kmsan_poison_shadow+0x6d/0xc0 mm/kmsan/kmsan.c:211 slab_alloc_node mm/slub.c:2743 __kmalloc_node_track_caller+0x200/0x360 mm/slub.c:4351 __kmalloc_reserve net/core/skbuff.c:138 __alloc_skb+0x26b/0x840 net/core/skbuff.c:231 alloc_skb ./include/linux/skbuff.h:933 sctp_packet_transmit+0x31e/0x3a20 net/sctp/output.c:570 sctp_outq_flush+0xeb3/0x46e0 net/sctp/outqueue.c:885 sctp_outq_uncork+0xb2/0xd0 net/sctp/outqueue.c:750 sctp_side_effects net/sctp/sm_sideeffect.c:1773 sctp_do_sm+0x6962/0x6ec0 net/sctp/sm_sideeffect.c:1147 sctp_primitive_ASSOCIATE+0x12c/0x160 net/sctp/primitive.c:88 sctp_sendmsg+0x43e5/0x4f90 net/sctp/socket.c:1954 inet_sendmsg+0x498/0x670 net/ipv4/af_inet.c:762 sock_sendmsg_nosec net/socket.c:633 sock_sendmsg net/socket.c:643 SYSC_sendto+0x608/0x710 net/socket.c:1696 SyS_sendto+0x8a/0xb0 net/socket.c:1664 do_syscall_64+0xe6/0x130 arch/x86/entry/common.c:285 return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.S:246 ================================================================== Signed-off-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
-
