- 05 May, 2015 40 commits
-
-
Ido Shamay authored
[ Upstream commit e5eda89d ] Netdevice registration should be performed a the end of the driver initialization flow. If we don't do that, after calling register_netdevice, device callbacks may be issued by higher layers of the stack before final configuration of the device is done. For example (VXLAN configuration race), mlx4_SET_PORT_VXLAN was issued after the register_netdev command. System network scripts may configure the interface (UP) right after the registration, which also attach unicast VXLAN steering rule, before mlx4_SET_PORT_VXLAN was called, causing the firmware to fail the rule attachment. Fixes: 837052d0 ("net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling") Signed-off-by:
Ido Shamay <idos@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Mike Christie authored
commit b815fc12 upstream. This fixes a oops due to a double list add when adding a reject PDU for iscsit_allocate_iovecs allocation failures. The cmd has already been added to the conn_cmd_list in iscsit_setup_scsi_cmd, so this has us call iscsit_reject_cmd. Note that for ERL0 the reject PDU is not actually sent, so this patch is not completely tested. Just verified we do not oops. The problem is the add reject functions return -1 which is returned all the way up to iscsi_target_rx_thread which for ERL0 will drop the connection. Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Dmitry M. Fedin authored
commit 3dc8523f upstream. Adds an entry for Creative USB X-Fi to the rc_config array in mixer_quirks.c to allow use of volume knob on the device. Adds support for newer X-Fi Pro card, known as "Model No. SB1095" with USB ID "041e:3237" Signed-off-by:
Dmitry M. Fedin <dmitry.fedin@gmail.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Al Viro authored
commit 64b4e252 upstream. "ocfs2 syncs the wrong range" had been broken; prior to it the code was doing the wrong thing in case of O_APPEND, all right, but _after_ it we were syncing the wrong range in 100% cases. *ppos, aka iocb->ki_pos is incremented prior to that point, so we are always doing sync on the area _after_ the one we'd written to. Spotted by Joseph Qi <joseph.qi@huawei.com> back in January; unfortunately, I'd missed his mail back then ;-/ Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Takashi Iwai authored
commit cc7016ab upstream. Some BIOS version of Fujitsu Lifebook T731 seems to set up the headphone pin (0x21) without the assoc number 0x0f while it's set only to the output on the docking port (0x1a). With the recent commit [03ad6a8c: ALSA: hda - Fix "PCM" name being used on one DAC when there are two DACs], this resulted in the weird mixer element mapping where the headphone on the laptop is assigned as a shared volume with the speaker and the docking port is assigned as an individual headphone. This patch improves the situation by correcting the headphone pin config to the more appropriate value. Reported-and-tested-by:
Taylor Smock <smocktaylor@gmail.com> Signed-off-by:
-
Bart Van Assche authored
commit bba0bdd7 upstream. SCSI transport drivers and SCSI LLDs block a SCSI device if the transport layer is not operational. This means that in this state no requests should be processed, even if the REQ_PREEMPT flag has been set. This patch avoids that a rescan shortly after a cable pull sporadically triggers the following kernel oops: BUG: unable to handle kernel paging request at ffffc9001a6bc084 IP: [<ffffffffa04e08f2>] mlx4_ib_post_send+0xd2/0xb30 [mlx4_ib] Process rescan-scsi-bus (pid: 9241, threadinfo ffff88053484a000, task ffff880534aae100) Call Trace: [<ffffffffa0718135>] srp_post_send+0x65/0x70 [ib_srp] [<ffffffffa071b9df>] srp_queuecommand+0x1cf/0x3e0 [ib_srp] [<ffffffffa0001ff1>] scsi_dispatch_cmd+0x101/0x280 [scsi_mod] [<ffffffffa0009ad1>] scsi_request_fn+0x411/0x4d0 [scsi_mod] [<ffffffff81223b37>] __blk_run_queue+0x27/0x30 [<ffffffff8122a8d2>] blk_execute_rq_nowait+0x82/0x110 [<ffffffff8122a9c2>] blk_execute_rq+0x62/0xf0 [<ffffffffa000b0e8>] scsi_execute+0xe8/0x190 [scsi_mod] [<ffffffffa000b2f3>] scsi_execute_req+0xa3/0x130 [scsi_mod] [<ffffffffa000c1aa>] scsi_probe_lun+0x17a/0x450 [scsi_mod] [<ffffffffa000ce86>] scsi_probe_and_add_lun+0x156/0x480 [scsi_mod] [<ffffffffa000dc2f>] __scsi_scan_target+0xdf/0x1f0 [scsi_mod] [<ffffffffa000dfa3>] scsi_scan_host_selected+0x183/0x1c0 [scsi_mod] [<ffffffffa000edfb>] scsi_scan+0xdb/0xe0 [scsi_mod] [<ffffffffa000ee13>] store_scan+0x13/0x20 [scsi_mod] [<ffffffff811c8d9b>] sysfs_write_file+0xcb/0x160 [<ffffffff811589de>] vfs_write+0xce/0x140 [<ffffffff81158b53>] sys_write+0x53/0xa0 [<ffffffff81464592>] system_call_fastpath+0x16/0x1b [<00007f611c9d9300>] 0x7f611c9d92ff Reported-by:
Max Gurtuvoy <maxg@mellanox.com> Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
John Soni Jose authored
commit 2e7cee02 upstream. Kernel panic was happening as iscsi_host_remove() was called on a host which was not yet added. Signed-off-by:
John Soni Jose <sony.john-n@emulex.com> Reviewed-by:
-
Kailang Yang authored
commit a59d7199 upstream. Pin sense will active when power pin is wake up. Power pin will not wake up immediately during resume state. Add some delay to wait for power pin activated. Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
-
Al Viro authored
commit deeb8525 upstream. If we fail past the aio_setup_ring(), we need to destroy the mapping. We don't need to care about anybody having found ctx, or added requests to it, since the last failure exit is exactly the failure to make ctx visible to lookups. Reproducer (based on one by Joe Mario <jmario@redhat.com>): void count(char *p) { char s[80]; printf("%s: ", p); fflush(stdout); sprintf(s, "/bin/cat /proc/%d/maps|/bin/fgrep -c '/[aio] (deleted)'", getpid()); system(s); } int main() { io_context_t *ctx; int created, limit, i, destroyed; FILE *f; count("before"); if ((f = fopen("/proc/sys/fs/aio-max-nr", "r")) == NULL) perror("opening aio-max-nr"); else if (fscanf(f, "%d", &limit) != 1) fprintf(stderr, "can't parse aio-max-nr\n"); else if ((ctx = calloc(limit, sizeof(io_context_t))) == NULL) perror("allocating aio_context_t array"); else { for (i = 0, created = 0; i < limit; i++) { if (io_setup(1000, ctx + created) == 0) created++; } for (i = 0, destroyed = 0; i < created; i++) if (io_destroy(ctx[i]) == 0) destroyed++; printf("created %d, failed %d, destroyed %d\n", created, limit - created, destroyed); count("after"); } } Found-by:
Joe Mario <jmario@redhat.com> Signed-off-by:
-
Thomas Schlichter authored
commit c7e8bdf5 upstream. Fix a bug that leads to showing the name and description of C-state C0 as "<null>" in sysfs after the ACPI C-states changed (e.g. after AC->DC or DC->AC transition). The function poll_idle_init() in drivers/cpuidle/driver.c initializes the state 0 during cpuidle_register_driver(), so we better do not overwrite it again with '\0' during acpi_processor_cst_has_changed(). Signed-off-by:
Thomas Schlichter <thomas.schlichter@web.de> Reviewed-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Marek Szyprowski authored
commit 05b676ab upstream. TASK_SIZE is depends on the systems architecture (32 or 64 bits) and it should not be used for defining offset boundary for mmaping buffers for CAPTURE and OUTPUT queues. This patch fixes support for MMAP calls on the CAPTURE queue on 64bit architectures (like ARM64). Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Kamil Debski <k.debski@samsung.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Hans Verkuil authored
commit ab312030 upstream. The v4l2_dev field of struct video_device must be set correctly. This was never done for this driver, so no video nodes were created anymore. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Dan Carpenter authored
commit bc3b5b47 upstream. I don't have this hardware but it looks like we weren't adding bridge devices as intended. Maybe the bridge is always the last device? Fixes: 05b12500 ("PCI: cpcihp: Iterate over all devices in slot, not functions 0-7") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Yijing Wang <wangyijing@huawei.com> Signed-off-by:
-
Neal Cardwell authored
[ Upstream commit 666b8051 ] On processing cumulative ACKs, the FRTO code was not checking the SACKed bit, meaning that there could be a spurious FRTO undo on a cumulative ACK of a previously SACKed skb. The FRTO code should only consider a cumulative ACK to indicate that an original/unretransmitted skb is newly ACKed if the skb was not yet SACKed. The effect of the spurious FRTO undo would typically be to make the connection think that all previously-sent packets were in flight when they really weren't, leading to a stall and an RTO. Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Yuchung Cheng <ycheng@google.com> Fixes: e33099f9 ("tcp: implement RFC5682 F-RTO") Signed-off-by:
-
Jonathan Davies authored
commit 0c36820e upstream. xen-netfront limits transmitted skbs to be at most 44 segments in size. However, GSO permits up to 65536 bytes, which means a maximum of 45 segments of 1448 bytes each. This slight reduction in the size of packets means a slight loss in efficiency. Since c/s 9ecd1a75, xen-netfront sets gso_max_size to XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER, where XEN_NETIF_MAX_TX_SIZE is 65535 bytes. The calculation used by tcp_tso_autosize (and also tcp_xmit_size_goal since c/s 6c09fa09) in determining when to split an skb into two is sk->sk_gso_max_size - 1 - MAX_TCP_HEADER. So the maximum permitted size of an skb is calculated to be (XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER) - 1 - MAX_TCP_HEADER. Intuitively, this looks like the wrong formula -- we don't need two TCP headers. Instead, there is no need to deviate from the default gso_max_size of 65536 as this already accommodates the size of the header. Currently, the largest skb transmitted by netfront is 63712 bytes (44 segments of 1448 bytes each), as observed via tcpdump. This patch makes netfront send skbs of up to 65160 bytes (45 segments of 1448 bytes each). Similarly, the maximum allowable mtu does not need to subtract MAX_TCP_HEADER as it relates to the size of the whole packet, including the header. Fixes: 9ecd1a75 ("xen-netfront: reduce gso_max_size to account for max TCP header") Signed-off-by:
Jonathan Davies <jonathan.davies@citrix.com> Signed-off-by:
-
WANG Cong authored
commit d079535d upstream. In case we move the whole dev group to another netns, we should call for_each_netdev_safe(), otherwise we get a soft lockup: NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [ip:798] irq event stamp: 255424 hardirqs last enabled at (255423): [<ffffffff81a2aa95>] restore_args+0x0/0x30 hardirqs last disabled at (255424): [<ffffffff81a2ad5a>] apic_timer_interrupt+0x6a/0x80 softirqs last enabled at (255422): [<ffffffff81079ebc>] __do_softirq+0x2c1/0x3a9 softirqs last disabled at (255417): [<ffffffff8107a190>] irq_exit+0x41/0x95 CPU: 0 PID: 798 Comm: ip Not tainted 4.0.0-rc4+ #881 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 task: ffff8800d1b88000 ti: ffff880119530000 task.ti: ffff880119530000 RIP: 0010:[<ffffffff810cad11>] [<ffffffff810cad11>] debug_lockdep_rcu_enabled+0x28/0x30 RSP: 0018:ffff880119533778 EFLAGS: 00000246 RAX: ffff8800d1b88000 RBX: 0000000000000002 RCX: 0000000000000038 RDX: 0000000000000000 RSI: ffff8800d1b888c8 RDI: ffff8800d1b888c8 RBP: ffff880119533778 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 000000000000b5c2 R12: 0000000000000246 R13: ffff880119533708 R14: 00000000001d5a40 R15: ffff88011a7d5a40 FS: 00007fc01315f740(0000) GS:ffff88011a600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00007f367a120988 CR3: 000000011849c000 CR4: 00000000000007f0 Stack: ffff880119533798 ffffffff811ac868 ffffffff811ac831 ffffffff811ac828 ffff8801195337c8 ffffffff811ac8c9 ffff8801195339b0 ffff8801197633e0 0000000000000000 ffff8801195339b0 ffff8801195337d8 ffffffff811ad2d7 Call Trace: [<ffffffff811ac868>] rcu_read_lock+0x37/0x6e [<ffffffff811ac831>] ? rcu_read_unlock+0x5f/0x5f [<ffffffff811ac828>] ? rcu_read_unlock+0x56/0x5f [<ffffffff811ac8c9>] __fget+0x2a/0x7a [<ffffffff811ad2d7>] fget+0x13/0x15 [<ffffffff811be732>] proc_ns_fget+0xe/0x38 [<ffffffff817c7714>] get_net_ns_by_fd+0x11/0x59 [<ffffffff817df359>] rtnl_link_get_net+0x33/0x3e [<ffffffff817df3d7>] do_setlink+0x73/0x87b [<ffffffff810b28ce>] ? trace_hardirqs_off+0xd/0xf [<ffffffff81a2aa95>] ? retint_restore_args+0xe/0xe [<ffffffff817e0301>] rtnl_newlink+0x40c/0x699 [<ffffffff817dffe0>] ? rtnl_newlink+0xeb/0x699 [<ffffffff81a29246>] ? _raw_spin_unlock+0x28/0x33 [<ffffffff8143ed1e>] ? security_capable+0x18/0x1a [<ffffffff8107da51>] ? ns_capable+0x4d/0x65 [<ffffffff817de5ce>] rtnetlink_rcv_msg+0x181/0x194 [<ffffffff817de407>] ? rtnl_lock+0x17/0x19 [<ffffffff817de407>] ? rtnl_lock+0x17/0x19 [<ffffffff817de44d>] ? __rtnl_unlock+0x17/0x17 [<ffffffff818327c6>] netlink_rcv_skb+0x4d/0x93 [<ffffffff817de42f>] rtnetlink_rcv+0x26/0x2d [<ffffffff81830f18>] netlink_unicast+0xcb/0x150 [<ffffffff8183198e>] netlink_sendmsg+0x501/0x523 [<ffffffff8115cba9>] ? might_fault+0x59/0xa9 [<ffffffff817b5398>] ? copy_from_user+0x2a/0x2c [<ffffffff817b7b74>] sock_sendmsg+0x34/0x3c [<ffffffff817b7f6d>] ___sys_sendmsg+0x1b8/0x255 [<ffffffff8115c5eb>] ? handle_pte_fault+0xbd5/0xd4a [<ffffffff8100a2b0>] ? native_sched_clock+0x35/0x37 [<ffffffff8109e94b>] ? sched_clock_local+0x12/0x72 [<ffffffff8109eb9c>] ? sched_clock_cpu+0x9e/0xb7 [<ffffffff810cadbf>] ? rcu_read_lock_held+0x3b/0x3d [<ffffffff811ac1d8>] ? __fcheck_files+0x4c/0x58 [<ffffffff811ac946>] ? __fget_light+0x2d/0x52 [<ffffffff817b8adc>] __sys_sendmsg+0x42/0x60 [<ffffffff817b8b0c>] SyS_sendmsg+0x12/0x1c [<ffffffff81a29e32>] system_call_fastpath+0x12/0x17 Fixes: e7ed828f ("netlink: support setting devgroup parameters") Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Michal Kubeček authored
[ Upstream commit d0c294c5 ] On s390x, gcc 4.8 compiles this part of tcp_v6_early_demux() struct dst_entry *dst = sk->sk_rx_dst; if (dst) dst = dst_check(dst, inet6_sk(sk)->rx_dst_cookie); to code reading sk->sk_rx_dst twice, once for the test and once for the argument of ip6_dst_check() (dst_check() is inline). This allows ip6_dst_check() to be called with null first argument, causing a crash. Protect sk->sk_rx_dst access by ACCESS_ONCE() both in IPv4 and IPv6 TCP early demux code. Fixes: 41063e9d ("ipv4: Early TCP socket demux.") Fixes: c7109986 ("ipv6: Early TCP socket demux") Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Shachar Raindel authored
commit 8494057a upstream. Properly verify that the resulting page aligned end address is larger than both the start address and the length of the memory area requested. Both the start and length arguments for ib_umem_get are controlled by the user. A misbehaving user can provide values which will cause an integer overflow when calculating the page aligned end address. This overflow can cause also miscalculation of the number of pages mapped, and additional logic issues. Addresses: CVE-2014-8159 Signed-off-by:
Shachar Raindel <raindel@mellanox.com> Signed-off-by:
Jack Morgenstein <jackm@mellanox.com> Signed-off-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
-
Johannes Berg authored
commit 788211d8 upstream. There's an issue with the way the RX A-MPDU reorder timer is deleted that can cause a kernel crash like this: * tid_rx is removed - call_rcu(ieee80211_free_tid_rx) * station is destroyed * reorder timer fires before ieee80211_free_tid_rx() runs, accessing the station, thus potentially crashing due to the use-after-free The station deletion is protected by synchronize_net(), but that isn't enough -- ieee80211_free_tid_rx() need not have run when that returns (it deletes the timer.) We could use rcu_barrier() instead of synchronize_net(), but that's much more expensive. Instead, to fix this, add a field tracking that the session is being deleted. In this case, the only re-arming of the timer happens with the reorder spinlock held, so make that code not rearm it if the session is being deleted and also delete the timer after setting that field. This ensures the timer cannot fire after ___ieee80211_stop_rx_ba_session() returns, which fixes the problem. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
Stefan Lippers-Hollmann authored
commit 80313b30 upstream. The ASRock Q1900DC-ITX mainboard (Baytrail-D) hangs randomly in both BIOS and UEFI mode while rebooting unless reboot=pci is used. Add a quirk to reboot via the pci method. The problem is very intermittent and hard to debug, it might succeed rebooting just fine 40 times in a row - but fails half a dozen times the next day. It seems to be slightly less common in BIOS CSM mode than native UEFI (with the CSM disabled), but it does happen in either mode. Since I've started testing this patch in late january, rebooting has been 100% reliable. Most of the time it already hangs during POST, but occasionally it might even make it through the bootloader and the kernel might even start booting, but then hangs before the mode switch. The same symptoms occur with grub-efi, gummiboot and grub-pc, just as well as (at least) kernel 3.16-3.19 and 4.0-rc6 (I haven't tried older kernels than 3.16). Upgrading to the most current mainboard firmware of the ASRock Q1900DC-ITX, version 1.20, does not improve the situation. ( Searching the web seems to suggest that other Bay Trail-D mainboards might be affected as well. ) -- Signed-off-by:
Stefan Lippers-Hollmann <s.l-h@gmx.de> Cc: Matt Fleming <matt.fleming@intel.com> Link: http://lkml.kernel.org/r/20150330224427.0fb58e42@mirSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Peter Ujfalusi authored
commit 02d88b73 upstream. In omap_dma_start_desc the vdesc->node is removed from the virt-dma framework managed lists (to be precise from the desc_issued list). If a terminate_all comes before the transfer finishes the omap_desc will not be freed up because it is not in any of the lists and we stopped the DMA channel so the transfer will not going to complete. There is no special sequence for leaking memory when using cyclic (audio) transfer: with every start and stop of a cyclic transfer the driver leaks struct omap_desc worth of memory. Free up the allocated memory directly in omap_dma_terminate_all() since the framework will not going to do that for us. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> CC: <linux-omap@vger.kernel.org> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Petr Kulhavy authored
commit 5ca9e7ce upstream. If edma_terminate_all() was called while a transfer was running (i.e. after edma_execute() but before edma_callback()) the echan->edesc was not freed. This was due to the fact that a running transfer is on none of the vchan lists: desc_submitted, desc_issued, desc_completed (edma_execute() removes it from the desc_issued list), so the vchan_dma_desc_free_list() called at the end of edma_terminate_all() didn't find it and didn't free it. This bug was found on an AM1808 based hardware (very similar to da850evm, however using the second MMC/SD controller), where intense operations on the SD card wasted the device 128MB RAM within a couple of days. Peter Ujfalusi: The issue is even more severe since it affects cyclic (audio) transfers as well. In this case starting/stopping audio will results memory leak. Signed-off-by:
Petr Kulhavy <petr@barix.com> Signed-off-by:
-
Darshana Padmadas authored
commit 4ce7ca89 upstream. This patch uses iio_trigger_get to increment the reference count of trigger device, to avoid incorrect assignment. Can result in a null pointer dereference during removal if the trigger has been changed before removal. This patch refers to a similar situation encountered through the following discussion: http://www.spinics.net/lists/linux-iio/msg13669.htmlSigned-off-by:
Darshana Padmadas <darshanapadmadas@gmail.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
David Miller authored
commit f2c9e560 upstream. Use readb() and memcpy_fromio() accessors instead. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Stefan Agner authored
commit 8e4934c6 upstream. When the receiver was enabled during startup, a character could have been in the FIFO when the UART get initially used. The driver configures the (receive) watermark level, and flushes the FIFO. However, the receive flag (RDRF) could still be set at that stage (as mentioned in the register description of UARTx_RWFIFO). This leads to an interrupt which won't be handled properly in interrupt mode: The receive interrupt function lpuart_rxint checks the FIFO count, which is 0 at that point (due to the flush during initialization). The problem does not manifest when using DMA to receive characters. Fix this situation by explicitly read the status register, which leads to clearing of the RDRF flag. Due to the flush just after the status flag read, a explicit data read is not to required. Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Doug Goldstein authored
commit b229a0f8 upstream. This patch uses the existing CALAO Systems ftdi_8u2232c_probe in order to avoid attaching a TTY to the JTAG port as this board is based on the CALAO Systems reference design and needs the same fix up. Signed-off-by:
Doug Goldstein <cardoe@cardoe.com> [johan: clean up probe logic ] Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Lu Baolu authored
commit 227a4fd8 upstream. When a device with an isochronous endpoint is plugged into the Intel xHCI host controller, and the driver submits multiple frames per URB, the xHCI driver will set the Block Event Interrupt (BEI) flag on all but the last TD for the URB. This causes the host controller to place an event on the event ring, but not send an interrupt. When the last TD for the URB completes, BEI is cleared, and we get an interrupt for the whole URB. However, under Intel xHCI host controllers, if the event ring is full of events from transfers with BEI set, an "Event Ring is Full" event will be posted to the last entry of the event ring, but no interrupt is generated. Host will cease all transfer and command executions and wait until software completes handling the pending events in the event ring. That means xHC stops, but event of "event ring is full" is not notified. As the result, the xHC looks like dead to user. This patch is to apply XHCI_AVOID_BEI quirk to Intel xHC devices. And it should be backported to kernels as old as 3.0, that contains the commit 69e848c2 ("Intel xhci: Support EHCI/xHCI port switching."). Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Tested-by:
Alistair Grant <akgrant0710@gmail.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Lu Baolu authored
commit 9425183d upstream. Linux xHCI driver doesn't report and handle port cofig error change. If Port Configure Error for root hub port occurs, CEC bit in PORTSC would be set by xHC and remains 1. This happends when the root port fails to configure its link partner, e.g. the port fails to exchange port capabilities information using Port Capability LMPs. Then the Port Status Change Events will be blocked until all status change bits(CEC is one of the change bits) are cleared('0') (refer to xHCI spec 4.19.2). Otherwise, the port status change event for this root port will not be generated anymore, then root port would look like dead for user and can't be recovered until a Host Controller Reset(HCRST). This patch is to check CEC bit in PORTSC in xhci_get_port_status() and set a Config Error in the return status if CEC is set. This will cause a ClearPortFeature request, where CEC bit is cleared in xhci_clear_port_change_bit(). [The commit log is based on initial Marvell patch posted at http://marc.info/?l=linux-kernel&m=142323612321434&w=2] Reported-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Andreas Werner authored
commit 555828ef upstream. Return EPROBE_DEFER if Regulator returns EPROBE_DEFER If the Flexcan driver is built into kernel and a regulator is used to enable the CAN transceiver, the Flexcan driver may not use the regulator. When initializing the Flexcan device with a regulator defined in the device tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence the Flexcan init fails. The solution for this is to return EPROBE_DEFER if regulator is not initialized and wait until the regulator is initialized. Signed-off-by:
Andreas Werner <kernel@andy89.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
David Disseldorp authored
commit e1e9bda2 upstream. Under intermittent network outages, find_writable_file() is susceptible to the following race condition, which results in a user-after-free in the cifs_writepages code-path: Thread 1 Thread 2 ======== ======== inv_file = NULL refind = 0 spin_lock(&cifs_file_list_lock) // invalidHandle found on openFileList inv_file = open_file // inv_file->count currently 1 cifsFileInfo_get(inv_file) // inv_file->count = 2 spin_unlock(&cifs_file_list_lock); cifs_reopen_file() cifs_close() // fails (rc != 0) ->cifsFileInfo_put() spin_lock(&cifs_file_list_lock) // inv_file->count = 1 spin_unlock(&cifs_file_list_lock) spin_lock(&cifs_file_list_lock); list_move_tail(&inv_file->flist, &cifs_inode->openFileList); spin_unlock(&cifs_file_list_lock); cifsFileInfo_put(inv_file); ->spin_lock(&cifs_file_list_lock) // inv_file->count = 0 list_del(&cifs_file->flist); // cleanup!! kfree(cifs_file); spin_unlock(&cifs_file_list_lock); spin_lock(&cifs_file_list_lock); ++refind; // refind = 1 goto refind_writable; At this point we loop back through with an invalid inv_file pointer and a refind value of 1. On second pass, inv_file is not overwritten on openFileList traversal, and is subsequently dereferenced. Signed-off-by:
David Disseldorp <ddiss@suse.de> Reviewed-by:
Jeff Layton <jlayton@samba.org> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Sachin Prabhu authored
commit 2477bc58 upstream. While attempting to clone a file on a samba server, we receive a STATUS_INVALID_DEVICE_REQUEST. This is mapped to -EOPNOTSUPP which isn't handled in smb2_clone_range(). We end up looping in the while loop making same call to the samba server over and over again. The proposed fix is to exit and return the error value when encountered with an unhandled error. Signed-off-by:
Sachin Prabhu <sprabhu@redhat.com> Signed-off-by:
Steve French <steve.french@primarydata.com> Signed-off-by:
-
Nathaniel W Filardo authored
commit 5e71fc86 upstream. Add USB VID/PID for Xircom PGMFHUB USB/serial component. (The hub and SCSI bridge on that hardware are recognized out of the box by existing drivers.) Tested VID/PID using new_id and loopback connection and was met with success, but that's all the testing done. Signed-off-by:
Nathaniel Wesley Filardo <nwf@cs.jhu.edu> Signed-off-by:
-
Emmanuel Grumbach authored
commit 9c8928f5 upstream. The assumption before this patch was that we don't need to run again the INIT firmware after the system booted. The INIT firmware runs calibrations which impact the physical layer's behavior. Users reported that it may be helpful to run these calibrations again every time the interface is brought up. The penatly is minimal, since the calibrations run fast. This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=94341Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Doug Goldstein authored
commit 4899c054 upstream. Synapse Wireless uses the FTDI VID with a custom PID of 0x9090 for their SNAP Stick 200 product. Signed-off-by:
-
Martin Fuzzey authored
commit c1b03ab5 upstream. When an error occurred during event registration memory was freed twice resulting in kernel memory corruption and a crash in unrelated code. The problem was caused by iio_device_unregister_eventset() iio_device_unregister_sysfs() being called twice, once on the error path and then again via iio_dev_release(). Fix this by making these two functions idempotent so they may be called multiple times. The problem was observed before applying 78b33216 iio:core: Handle error when mask type is not separate Signed-off-by:
Martin Fuzzey <mfuzzey@parkeon.com> Signed-off-by:
-
Viorel Suman authored
commit 4dac0a8e upstream. A hardware fifo reset always imply an invalidation of the existing timestamps, so we'll clear timestamps fifo on successfull hardware fifo reset. Signed-off-by:
Viorel Suman <viorel.suman@gmail.com> Signed-off-by:
-
Octavian Purdila authored
commit 70dddeee upstream. If the in-kernel push interface is used we may have a different masks on the device buffer and the kernel buffer and in this case the device should generate data for the reunion of the buffers, which is available at indio_dev->active_scan_mask. Compiled tested only except for bmc150-accel which was tested at runtime with the hardware. Signed-off-by:
Octavian Purdila <octavian.purdila@intel.com> Signed-off-by:
-
Tejun Heo authored
commit c72efb65 upstream. From 1ebf33901ecc75d9496862dceb1ef0377980587c Mon Sep 17 00:00:00 2001 From: Tejun Heo <tj@kernel.org> Date: Mon, 23 Mar 2015 00:08:19 -0400 2f800fbd ("writeback: fix dirtied pages accounting on redirty") introduced account_page_redirty() which reverts stat updates for a redirtied page, making BDI_DIRTIED no longer monotonically increasing. bdi_update_write_bandwidth() uses the delta in BDI_DIRTIED as the basis for bandwidth calculation. While unlikely, since the above patch, the newer value may be lower than the recorded past value and underflow the bandwidth calculation leading to a wild result. Fix it by subtracing min of the old and new values when calculating delta. AFAIK, there hasn't been any report of it happening but the resulting erratic behavior would be non-critical and temporary, so it's possible that the issue is happening without being reported. The risk of the fix is very low, so tagged for -stable. Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jan Kara <jack@suse.cz> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Greg Thelen <gthelen@google.com> Fixes: 2f800fbd ("writeback: fix dirtied pages accounting on redirty") Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Vineet Gupta authored
commit 6914e1e3 upstream. The regfile provided to SA_SIGINFO signal handler as ucontext was off by one due to pt_regs gutter cleanups in 2013. Before handling signal, user pt_regs are copied onto user_regs_struct and copied back later. Both structs are binary compatible. This was all fine until commit 2fa91904 (ARC: pt_regs update #2) which removed the empty stack slot at top of pt_regs (corresponding to first pad) and made the corresponding fixup in struct user_regs_struct (the pad in there was moved out of @scratch - not removed altogether as it is part of ptrace ABI) struct user_regs_struct { + long pad; struct { - long pad; long bta, lp_start, lp_end,.... } scratch; ... } This meant that now user_regs_struct was off by 1 reg w.r.t pt_regs and signal code needs to user_regs_struct.scratch to reflect it as pt_regs, which is what this commit does. This problem was hidden for 2 years, because both save/restore, despite using wrong location, were using the same location. Only an interim inspection (reproducer below) exposed the issue. void handle_segv(int signo, siginfo_t *info, void *context) { ucontext_t *uc = context; struct user_regs_struct *regs = &(uc->uc_mcontext.regs); printf("regs %x %x\n", <=== prints 7 8 (vs. 8 9) regs->scratch.r8, regs->scratch.r9); } int main() { struct sigaction sa; sa.sa_sigaction = handle_segv; sa.sa_flags = SA_SIGINFO; sigemptyset(&sa.sa_mask); sigaction(SIGSEGV, &sa, NULL); asm volatile( "mov r7, 7 \n" "mov r8, 8 \n" "mov r9, 9 \n" "mov r10, 10 \n" :::"r7","r8","r9","r10"); *((unsigned int*)0x10) = 0; } Fixes: 2fa91904 "ARC: pt_regs update #2: Remove unused gutter at start of pt_regs" Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Sergei Antonov authored
commit 98cf21c6 upstream. Fix B-tree corruption when a new record is inserted at position 0 in the node in hfs_brec_insert(). In this case a hfs_brec_update_parent() is called to update the parent index node (if exists) and it is passed hfs_find_data with a search_key containing a newly inserted key instead of the key to be updated. This results in an inconsistent index node. The bug reproduces on my machine after an extents overflow record for the catalog file (CNID=4) is inserted into the extents overflow B-tree. Because of a low (reserved) value of CNID=4, it has to become the first record in the first leaf node. The resulting first leaf node is correct: ---------------------------------------------------- | key0.CNID=4 | key1.CNID=123 | key2.CNID=456, ... | ---------------------------------------------------- But the parent index key0 still contains the previous key CNID=123: ----------------------- | key0.CNID=123 | ... | ----------------------- A change in hfs_brec_insert() makes hfs_brec_update_parent() work correctly by preventing it from getting fd->record=-1 value from __hfs_brec_find(). Along the way, I removed duplicate code with unification of the if condition. The resulting code is equivalent to the original code because node is never 0. Also hfs_brec_update_parent() will now return an error after getting a negative fd->record value. However, the return value of hfs_brec_update_parent() is not checked anywhere in the file and I'm leaving it unchanged by this patch. brec.c lacks error checking after some other calls too, but this issue is of less importance than the one being fixed by this patch. Signed-off-by:
Sergei Antonov <saproj@gmail.com> Cc: Joe Perches <joe@perches.com> Reviewed-by:
Vyacheslav Dubeyko <slava@dubeyko.com> Acked-by:
Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Anton Altaparmakov <aia21@cam.ac.uk> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
