Add device-tree for Acer Iconia Tab A500, which is NVIDIA Tegra20-based
tablet device.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The SOR controller needs the AVDD I/O and VDD HDMI PLL supplies in order
to operate correctly. Make sure to specify them for Nyan boards.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tegra30 has a DSI controller, although it is never used on any of the
devices supported by the upstream Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The DPAUX controller device tree bindings require the bus to have an
i2c-bus subnode to distinguish between I2C clients and pinmux groups.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The SDHCI on Tegra30 is in fact not backwards-compatible with the
instantiation found on earlier SoCs. Drop the misleading compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The display controller on Tegra30 is in fact not backwards-compatible
with the instantiation found on earlier SoCs. Drop the misleading
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>

This was probably left there by mistake or perhaps was a typo in the
first place. Remove it.

Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The DSI output needs to specify a parent clock that will be used to
drive both the output and the display controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>

SRAM nodes should be named sram@<unit-address> to match the bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Seaboard uses a non-existing, possibly obsoleted, binding for the
battery. Move to the standard binding which seems to be a super-
set of the odl binding.
Signed-off-by: Thierry Reding <treding@nvidia.com>

LED nodes should be named led-* to match the bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Unit-addresses should be numeric. This fixes a validation failure seen
using the json-schema tooling.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Simple panels can only have a single power supply. The second listed
supply is not needed because it is also the input supply of the first
supply and therefore will always be on at the same time.

In retrospect the panel probably doesn't qualify as simple since it
apparently does need both of these supplies, even if in the case of the
Medcom Wide it isn't necessary to explicitly hook them up.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Use commas rather than underscores to separate the various parts of the
unit-address in CPU OPPs to make them properly validate under the json-
schema bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The Tegra SDHCI controllers need to have a clock-names property
according to the bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>

This is purely to make the json-schema validation tools happy because
they cannot deal with string arrays that may be in arbitrary order.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The memory controller exposes a set of memory client resets and needs to
specify the #reset-cells property in order to advertise the number of
cells needed to describe each of the resets.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Both Nyan boards as well as Venice2 are missing panel power supplies.
Add them.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Run the micro-USB A/B port on Jetson TK1 in host mode by default.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tuple boundaries should be marked by < and > to make it clear which
cells are part of the same tuple. This also helps the json-schema based
validation tooling to properly parse this data.

While at it, also remove the "immovable" bit from PCI addresses. All of
these addresses are in fact "movable".

Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Ethernet device should be named "ethernet@<unit-address>".

Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Audio codecs need a #sound-dai-cells property, so add one to the audio
codecs on various Tegra-based boards that don't have one.

Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

USB PHYs must have a #phy-cells property, so add one to the Tegra USB
PHYs which don't have one.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The SDHCI controller instantiated on Tegra114 is not backwards-
compatible with the version on Tegra30, so remove the corresponding
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The new json-schema based validation tools require SD/MMC controller
nodes to be named mmc. Rename all references to them.

Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The parent clocks are determined by the output that will be used, not by
the display controller that drives the output. On previous generations a
simple RGB output used to be part of the display controller and hence an
explicit parent clock needed to be assigned to the display controller to
drive the RGB output. Starting with Tegra124, that RGB output has been
dropped and the parent clock can therefore be removed from the display
controller device tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The display controller on Tegra114 is in fact not backwards-compatible
with the instantiation found on earlier SoCs. Drop the misleading
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The instantiation of gr3d in Tegra114 is not backwards-compatible with
the version found on earlier chips. Remove the misleading compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The instantiation of gr2d in Tegra114 is not backwards-compatible with
the version found on earlier chips. While the hardware IP is identical,
the compatible string also describes the integration of the IP, which
in the case of Tegra114 is slightly different in that it's part of the
HEG power partition, whereas it wasn't previously.

Drop the misleading compatible string so that drivers that support the
older integrations cannot match on it. Since they wouldn't be able to
control the power partition, such driver wouldn't be able to access any
of the registers of the IP.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The host1x device tree bindings require the clock- and interrupt-names
properties to be present, so add them where missing.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The host1x is not a simple bus, so drop the corresponding compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The correct DSI/CSI supply property is called vdd-dsi-csi-supply, so use
that instead of the wrong vdd-supply property.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The correct DSI/CSI supply property is called vdd-dsi-csi-supply, so use
that instead of the wrong vdd-supply property.
Signed-off-by: Thierry Reding <treding@nvidia.com>

This property is not documented and will cause a validation failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The standard way to do this is to list out the regulators at the top
level. Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The standard way to do this is to list out the clocks at the top-level.
Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The Tegra SDHCI controller bindings state that the clock-names property
is required, so add the missing properties on Tegra114.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Pull SafeSetID update from Micah Morton:
 "Add additional LSM hooks for SafeSetID

  SafeSetID is capable of making allow/deny decisions for set*uid calls
  on a system, and we want to add similar functionality for set*gid
  calls.

  The work to do that is not yet complete, so probably won't make it in
  for v5.8, but we are looking to get this simple patch in for v5.8
  since we have it ready.

  We are planning on the rest of the work for extending the SafeSetID
  LSM being merged during the v5.9 merge window"

* tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux:
  security: Add LSM hooks to set*gid syscalls

The SafeSetID LSM uses the security_task_fix_setuid hook to filter
set*uid() syscalls according to its configured security policy. In
preparation for adding analagous support in the LSM for set*gid()
syscalls, we add the requisite hook here. Tested by putting print
statements in the security_task_fix_setgid hook and seeing them get hit
during kernel boot.
Signed-off-by: Thomas Cedeno <thomascedeno@google.com>
Signed-off-by: Micah Morton <mortonm@chromium.org>