Add ACPI IDs for thermal drivers for Alder Lake support.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201117194802.503337-1-srinivas.pandruvada@linux.intel.com

Prevent build failure if the option CONFIG_ENERGY_MODEL is not set. The
devfreq cooling is able to operate without the Energy Model.
Don't use dev->em_pd directly and use local pointer.

Fixes: 615510fe ("thermal: devfreq_cooling: remove old power model and use EM")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201215154221.8828-1-lukasz.luba@arm.com

The ops is only showing a trace telling a critical trip point is
crossed. The same information is given by the thermal framework.

This is redundant, remove the code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20201210121514.25760-4-daniel.lezcano@linaro.org

Currently there is no way to the sensors to directly call an ops in
interrupt mode without calling thermal_zone_device_update assuming all
the trip points are defined.

A sensor may want to do something special if a trip point is hot or
critical.

This patch adds the critical and hot ops to the thermal zone device,
so a sensor can directly invoke them or let the thermal framework to
call the sensor specific ones.
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20201210121514.25760-2-daniel.lezcano@linaro.org

The actual code is silently ignoring a thermal zone update when a
driver is requesting it without a get_temp ops set.

That looks not correct, as the caller should not have called this
function if the thermal zone is unable to read the temperature.

That makes the code less robust as the check won't detect the driver
is inconsistently using the thermal API and that does not help to
improve the framework as these circumvolutions hide the problem at the
source.

In order to detect the situation when it happens, let's add a warning
when the update is requested without the get_temp() ops set.

Any warning emitted will have to be fixed at the source of the
problem: the caller must not call thermal_zone_device_update if there
is not get_temp callback set.

Cc: Thara Gopinath <thara.gopinath@linaro.org>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20201210121514.25760-1-daniel.lezcano@linaro.org

Register devfreq cooling device and attempt to register Energy Model. This
will add the devfreq device to the Energy Model framework. It will create
a dedicated and unified data structures used i.e. in thermal framework.
It uses simplified Energy Model, created based on voltage, frequency
and DT 'dynamic-power-coefficient'.
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-6-lukasz.luba@arm.com

Remove old power model and use new Energy Model to calculate the power
budget. It drops static + dynamic power calculations and power table
in order to use Energy Model performance domain data. This model
should be easy to use and could find more users. It is also less
complicated to setup the needed structures.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-5-lukasz.luba@arm.com

The Energy Model (EM) framework supports devices such as Devfreq. Create
new registration function which automatically register EM for the thermal
devfreq_cooling devices. This patch prepares the code for coming changes
which are going to replace old power model with the new EM.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-4-lukasz.luba@arm.com

Devfreq cooling needs to now the correct status of the device in order
to operate. Devfreq framework can change the device status in the
background. To mitigate issues make a copy of the status structure and use
it for internal calculations.

In addition this patch adds normalization function, which also makes sure
that whatever data comes from the device, the load will be in range from 1
to 1024.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-3-lukasz.luba@arm.com

Prepare for deleting the static and dynamic power calculation and clean
the trace function. These two fields are going to be removed in the next
changes.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> # for tracing code
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-2-lukasz.luba@arm.com

Change "Burusty" to "bursty".
Reported-by: Michael Larabel <Michael@phoronix.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210213324.2113041-1-srinivas.pandruvada@linux.intel.com

Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210135432.1249-1-zhengyongjun3@huawei.com

Use macro for temperature calculation
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210124801.13850-1-sumeet.r.pawnikar@intel.com

Added processor thermal device mail box interface for workload hints
setting. These hints will give indication to hardware to better manage
power and thermals. The supported hints are:
idle
semi_active
burusty
sustained
battery_life

For example when the system is on battery, the hardware can be less
aggressive in power ramp up.

This will create an attribute group at
/sys/bus/pci/devices/0000:00:04.0/workload_request

This folder contains two attributes:
workload_available_types : (RO):  This shows available workload types
workload_type: (RW) : Allows to set and get current workload type
setting
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-4-srinivas.pandruvada@linux.intel.com

Add support for RFIM (Radio Frequency Interference Mitigation) support
via processor thermal PCI device. This drivers allows adjustment of
FIVR (Fully Integrated Voltage Regulator) and DDR (Double Data Rate)
frequencies to avoid RF interference with WiFi and 5G.

Switching voltage regulators (VR) generate radiated EMI or RFI at the
fundamental frequency and its harmonics. Some harmonics may interfere
with very sensitive wireless receivers such as Wi-Fi and cellular that
are integrated into host systems like notebook PCs.  One of mitigation
methods is requesting SOC integrated VR (IVR) switching frequency to a
small % and shift away the switching noise harmonic interference from
radio channels.  OEM or ODMs can use the driver to control SOC IVR
operation within the range where it does not impact IVR performance.

DRAM devices of DDR IO interface and their power plane can generate EMI
at the data rates. Similar to IVR control mechanism, Intel offers a
mechanism by which DDR data rates can be changed if several conditions
are met: there is strong RFI interference because of DDR; CPU power
management has no other restriction in changing DDR data rates;
PC ODMs enable this feature (real time DDR RFI Mitigation referred to as
DDR-RFIM) for Wi-Fi from BIOS.

This change exports two folders under /sys/bus/pci/devices/0000:00:04.0.
One folder "fivr" contains all attributes exposed for controling FIVR
features. The other folder "dvfs" contains all attributes for DDR
features.

Changes done to implement:
- New module for rfim interfaces
- Two new per processor features for DDR and FIVR
- Enable feature for Tiger Lake (FIVR only) and Alder Lake

The attributes exposed and explanation:

FIVR attributes

vco_ref_code_lo (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 3-bit LSB field.

vco_ref_code_hi (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 8-bit MSB field.

spread_spectrum_pct (RW): Set the FIVR spread spectrum clocking
percentage

spread_spectrum_clk_enable (RW): Enable/disable of the FIVR spread
spectrum clocking feature

rfi_vco_ref_code (RW): This field is a read only status register which
reflects the current FIVR switching frequency

fivr_fffc_rev (RW): This field indicated the revision of the FIVR HW.

DVFS attributes

rfi_restriction_run_busy (RW): Request the restriction of specific DDR
data rate and set this value 1. Self reset to 0 after operation.

rfi_restriction_err_code (RW): Values:  0 :Request is accepted, 1:Feature
disabled, 2: the request restricts more points than it is allowed

rfi_restriction_data_rate_Delta (RW): Restricted DDR data rate for RFI
protection: Lower Limit

rfi_restriction_data_rate_Base (RW): Restricted DDR data rate for RFI
protection: Upper Limit

ddr_data_rate_point_0 (RO): DDR data rate selection 1st point

ddr_data_rate_point_1 (RO): DDR data rate selection 2nd point

ddr_data_rate_point_2 (RO): DDR data rate selection 3rd point

ddr_data_rate_point_3 (RO): DDR data rate selection 4th point

rfi_disable (RW): Disable DDR rate change feature
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-3-srinivas.pandruvada@linux.intel.com

Added AlderLake PCI device id to support processor thermal driver. Reuse
the feature set (just includes RAPL) from previous generations.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-2-srinivas.pandruvada@linux.intel.com

The Processor Thermal PCI device supports multiple features. Currently
we export only RAPL. But we need more features from this device exposed
for Tiger Lake and Alder Lake based platforms. So re-structure the
current MMIO interface, so that more features can be added cleanly.

No functional changes are expected with this change.

Changes done in this patch:
- Using PCI_DEVICE_DATA(), hence names of defines changed
- Move RAPL MMIO code to its own module
- Move the RAPL MMIO offsets to RAPL MMIO module
- Adjust Kconfig dependency of PROC_THERMAL_MMIO_RAPL
- Per processor driver data now contains the supported features
- Moved all the common data structures and defines to a common header
  file
- This new header file contains all the processor_thermal_* interfaces
- Based on the features supported the module interface is called
- Each module atleast provides one add and one remove function
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-1-srinivas.pandruvada@linux.intel.com

Add support for R-Car V3U. The new THCODE values are taken from the
example in the datasheet.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126223028.3119044-4-niklas.soderlund+renesas@ragnatech.se

Add support for R-Car V3U. The V3U IP differs a bit from its siblings in
such way that it have 4 TSC nodes and the interrupts are not routed to
the INTC-AP but to the ECM.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126223028.3119044-2-niklas.soderlund+renesas@ragnatech.se

Currently the code checks the interval value when the temperature is
read which is bad for two reasons:

 - checking and setting the interval in the get_temp callback is
   inaccurate and awful, that can be done when changing the value.

 - Changing the thermal zone structure internals is an abuse of the
   exported structure, moreover no lock is taken here.

The goal of this patch is to solve the first item by using the 'set'
function called when changing the interval. The check is done there
and removed from the get_temp function. If the thermal zone was not
initialized yet, the interval is not updated in this case as that will
happen in the init function when registering the thermal zone device.

I don't have any hardware to test the changes.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Peter Kaestle <peter@piie.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201203071738.2363701-2-daniel.lezcano@linaro.org

The module parameter can be set by using ops to get and set the
values. The change will allow to check the correctness of the interval
value everytime it is changed instead of checking in the get_temp
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Peter Kaestle <peter@piie.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201203071738.2363701-1-daniel.lezcano@linaro.org

Prior to returning an error in probe, disable the previously
enabled clock.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201202232448.2692-2-festevam@gmail.com

Currently the error message does not print the correct error code.

Fix it by initializing 'ret' to the proper error code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201202232448.2692-1-festevam@gmail.com

Remove the usage of interrupts for the normal temperature operation and
depend on the polling performed by the thermal core. This is done to
prepare to use the interrupts as they are intended to trigger once
specific trip points are passed and not to react to temperature changes
in the normal operational range.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126220923.3107213-1-niklas.soderlund+renesas@ragnatech.se

The only usage of these structs is to assign their address to the
thermal_zone_attribute_groups array, which consists of pointers to
const, so make them const to allow the compiler to put them in read-only
memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201128234342.36684-1-rikard.falkeborn@gmail.com

The PID coefficients should be estimated again when there was a change to
sustainable power value made by user. This change removes unused argument
'force' and makes the function ready for such updates.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-4-lukasz.luba@arm.com

The sustainable power value might come from the Device Tree or can be
estimated in run time. The sustainable power might be updated by the user
via sysfs interface, which should trigger new estimation of PID
coefficients. There is no need to estimate it every time when the
governor is called and temperature is high. Instead, store the estimated
value and make it available via standard sysfs interface, so it can be
checked from the user-space.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-3-lukasz.luba@arm.com

Intelligent Power Allocation (IPA) is built around the PID controller
concept. The initialization code tries to setup the environment based on
the information available in DT or estimate the value based on minimum
power reported by each of the cooling device. The estimation will have an
impact on the PID controller behaviour via the related 'k_po', 'k_pu',
'k_i' coefficients and also on the power budget calculation.

This change prevents the situation when 'k_i' is relatively big compared
to 'k_po' and 'k_pu' values. This might happen when the estimation for
'sustainable_power' returned small value, thus 'k_po' and 'k_pu' are
small.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-2-lukasz.luba@arm.com

The reference to acpi_gbl_FADT causes a build error when ACPI is not
enabled. Fix by making that conditional on CONFIG_ACPI.

../drivers/thermal/intel/intel_pch_thermal.c: In function 'pch_wpt_suspend':
../drivers/thermal/intel/intel_pch_thermal.c:217:8: error: 'acpi_gbl_FADT' undeclared (first use in this function); did you mean 'acpi_get_type'?
  if (!(acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0))
        ^~~~~~~~~~~~~

Fixes: ef63b043 ("thermal: intel: pch: fix S0ix failure due to PCH temperature above threshold")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201117023807.8266-1-rdunlap@infradead.org

Many monitoring tools read the CPU temperature using the hwmon
interface. Expose the thermal sensors on Amlogic boards as hwmon
devices.

Without this lm_sensors' "sensors" tool does not find any temperature
sensors. Now it prints:
  cpu_thermal-virtual-0
  Adapter: Virtual device
  temp1:        +44.7 C  (crit = +110.0 C)

  ddr_thermal-virtual-0
  Adapter: Virtual device
  temp1:        +45.9 C  (crit = +110.0 C)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201115190658.631578-1-martin.blumenstingl@googlemail.com

I noticed that I couldn't read the PCH temperature on my workstation
(C620 series chipset, w/ 2x Xeon Gold 5215 CPUs) directly, but had to go
through IPMI. Looking at the data sheet, it looks to me like the
existing intel PCH thermal driver should work without changes for
Lewisburg.

I suspect there's some other PCI IDs missing. But I hope somebody at
Intel would have an easier time figuring that out than I...

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/lkml/20200115184415.1726953-1-andres@anarazel.de/Signed-off-by: Andres Freund <andres@anarazel.de>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201113204916.1144907-1-andres@anarazel.de

The sysfs stats for cooling devices shows the time_in_state in msec,
remove the unwanted usertime comment.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/d5461bdf9ab6b6fee7f28f538582edbb426aa077.1605004905.git.viresh.kumar@linaro.org

- Factor out common required properties,
  - "interrupts", "clocks", and "power-domains" are required on R-Mobile
    APE6, too,
  - Invert logic to simplify descriptions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201028153541.1736279-1-geert+renesas@glider.be

If state has not changed successfully and we updated cpufreq_state,
next time when the new state is equal to cpufreq_state (not changed
successfully last time), we will return directly and miss a
freq_qos_update_request() that should have been.

Fixes: 5130802d ("thermal: cpu_cooling: Switch to QoS requests for freq limits")
Cc: v5.4+ <stable@vger.kernel.org> # v5.4+
Signed-off-by: Zhuguangqing <zhuguangqing@xiaomi.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106092243.15574-1-zhuguangqing83@gmail.com

Function thermal_add_hwmon_sysfs, hwmon will be NULL when
new_hwmon_device = 0, so there is no need to check, kfree will
handle NULL point.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201102023121.3312-1-bernard@vivo.com

The bitmap_* API is the standard way to access data in the bitfield.
So convert irq_ack to return an unsigned long, and make things to use
bitmap API.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201109114624.23035-1-frank@allwinnertech.com

When system tries to enter S0ix suspend state, just after active load
scenarios, it fails due to PCH current temperature is higher than set
threshold.
This patch introduces delay loop mechanism that allows PCH temperature
to go down below threshold during suspend so it won't fail to enter S0ix.
Add delay loop timeout and count as module parameters for user to tune it,
if required based on system design. This change notifies the different
warning messages like when PCH temperature above the threshold and
executing delay loop. Also, notify the messages when it success or
failure for S0ix entry.
Previously out of 1000 runs around 3 to 5 times it might fail to enter
S0ix just after heavy workload. With this change, S0ix failures reduced
as PCH cools down below threshold.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106170633.20838-1-sumeet.r.pawnikar@intel.com

MT8516 does not support thermal reset. Use device_reset_optional
instead of device_reset.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201021164231.3029956-3-fparent@baylibre.com

Add binding documentation for the MediaTek MT8516 SoC.
The SoC thermal IP is similar to MT2701.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201021164231.3029956-2-fparent@baylibre.com

MT8516 Thermal IP does not support reset. Make the resets property
optional in order to be able to support MT8516 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201021164231.3029956-1-fparent@baylibre.com