If dump is active during system reboot, shutdown or halt then invalidate
the fadump registration as it does not get invalidated automatically.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch introduces an sysfs interface '/sys/kernel/fadump_release_mem' to
invalidate the last fadump registration, invalidate '/proc/vmcore', release
the reserved memory for general use and re-register for future kernel dump.
Once the dump is copied to the disk, unlike phyp dump, the userspace tool
can release all the memory reserved for dump with one single operation of
echo 1 to '/sys/kernel/fadump_release_mem'.

Release the reserved memory region excluding the size of the memory required
for future kernel dump registration. And therefore, unlike kdump, Fadump
doesn't need a 2nd reboot to get back the system to the production
configuration.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

With the firmware-assisted dump support we don't require a reboot when we
are in second kernel after crash. The second kernel after crash is a normal
kernel boot and has knowledge about entire system RAM with the page tables
initialized for entire system RAM. Hence once the dump is saved to disk, we
can just release the reserved memory area for general use and continue
with second kernel as production kernel.

Hence when we release the reserved memory that contains dump data, the
'/proc/vmcore' will not be valid anymore. Hence this patch introduces
a cleanup routine that invalidates and removes the /proc/vmcore file. This
routine will be invoked before we release the reserved dump memory area.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Introduce a PT_NOTE program header that points to physical address of
vmcoreinfo_note buffer declared in kernel/kexec.c. The vmcoreinfo
note buffer is populated during crash_fadump() at the time of system
crash.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

When registered for firmware assisted dump on powerpc, firmware preserves
the registers for the active CPUs during a system crash. This patch reads
the cpu register data stored in Firmware-assisted dump format (except for
crashing cpu) and converts it into elf notes and updates the PT_NOTE program
header accordingly. The exact register state for crashing cpu is saved to
fadump crash info structure in scratch area during crash_fadump() and read
during second kernel boot.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Build the crash memory range list by traversing through system memory during
the first kernel before we register for firmware-assisted dump. After the
successful dump registration, initialize the elfcore header and populate
PT_LOAD program headers with crash memory ranges. The elfcore header is
saved in the scratch area within the reserved memory. The scratch area starts
at the end of the memory reserved for saving RMR region contents. The
scratch area contains fadump crash info structure that contains magic number
for fadump validation and physical address where the eflcore header can be
found. This structure will also be used to pass some important crash info
data to the second kernel which will help second kernel to populate ELF core
header with correct data before it gets exported through /proc/vmcore. Since
the firmware preserves the entire partition memory at the time of crash the
contents of the scratch area will be preserved till second kernel boot.

Since the memory dump exported through /proc/vmcore is in ELF format similar
to kdump, it will help us to reuse the kdump infrastructure for dump capture
and filtering. Unlike phyp dump, userspace tool does not need to refer any
sysfs interface while reading /proc/vmcore.

NOTE: The current design implementation does not address a possibility of
introducing additional fields (in future) to this structure without affecting
compatibility. It's on TODO list to come up with better approach to
address this.

Reserved dump area start => +-------------------------------------+
                            |  CPU state dump data                |
                            +-------------------------------------+
                            |  HPTE region data                   |
                            +-------------------------------------+
                            |  RMR region data                    |
Scratch area start       => +-------------------------------------+
                            |  fadump crash info structure {      |
                            |     magic nummber                   |
                     +------|---- elfcorehdr_addr                 |
                     |      |  }                                  |
                     +----> +-------------------------------------+
                            |  ELF core header                    |
Reserved dump area end   => +-------------------------------------+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

On 2012-02-20 11:02:51 Mon, Paul Mackerras wrote:
> On Thu, Feb 16, 2012 at 04:44:30PM +0530, Mahesh J Salgaonkar wrote:
>
> If I have read the code correctly, we are going to get this printk on
> non-pSeries machines or on older pSeries machines, even if the user
> has not put the fadump=on option on the kernel command line.  The
> printk will be annoying since there is no actual error condition.  It
> seems to me that the condition for the printk should include
> fw_dump.fadump_enabled.  In other words you should probably add
>
> 	if (!fw_dump.fadump_enabled)
> 		return 0;
>
> at the beginning of the function.

Hi Paul,

Thanks for pointing it out. Please find the updated patch below.

The existing patches above this (4/10 through 10/10) cleanly applies
on this update.

Thanks,
-Mahesh.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Reserve the memory during early boot to preserve CPU state data, HPTE region
and RMA (real mode area) region data in case of kernel crash. At the time of
crash, powerpc firmware will store CPU state data, HPTE region data and move
RMA region data to the reserved memory area.

If the firmware-assisted dump fails to reserve the memory, then fallback
to existing kexec-based kdump.

Most of the code implementation to reserve memory has been
adapted from phyp assisted dump implementation written by Linas Vepstas
and Manish Ahuja

This patch also introduces a config option CONFIG_FA_DUMP for firmware
assisted dump feature on Powerpc (ppc64) architecture.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Documentation for firmware-assisted dump. This document is based on the
original documentation written for phyp assisted dump by Linas Vepstas
and Manish Ahuja, with few changes to reflect the current implementation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

There are two separate flags controlling whether or not the MPIC is
reset during initialization, which is completely unnecessary, and only
one of them can be specified in the device tree.

Also, most platforms in-tree right now do actually want to reset the
MPIC during initialization anyways, which means lots of duplicate code
passing the MPIC_WANTS_RESET flag.

Fix all of the callers which currently do not pass the MPIC_WANTS_RESET
flag to pass the MPIC_NO_RESET flag, then remove the MPIC_WANTS_RESET
flag and make the code reset the MPIC by default.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The FreeScale PowerQUICC-III-compatible (mpc85xx/mpc86xx) MPICs do not
correctly report the number of hardware interrupt sources, so software
needs to override the detected value with "256".

To avoid needing to write custom board-specific code to detect that
scenario, allow it to be easily overridden in the device-tree.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The mpic->irq_count variable is only used as a software error-checking
limit to determine whether or not an IRQ number is valid.  In board code
which does not manually specify an IRQ count to mpic_alloc(), i.e. 0, it
is automatically detected from the number of ISUs and the ISU size.

In practice, all hardware ends up with irq_count == num_sources, so all
of the runtime checks on mpic->irq_count should just check the value of
mpic->num_sources instead.

When platform hardware does not correctly report the number of IRQs,
which only happens on the MPC85xx/MPC86xx, the MPIC_BROKEN_FRR_NIRQS
flag is used to override the detected value of num_sources with the
manual irq_count parameter.  Since there's no need to manually specify
the number of IRQs except in this case, the extra flag can be eliminated
and the test changed to "irq_count != 0".
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The Freescale MPIC (and perhaps others in the future) is incapable of
routing non-IPI interrupts to more than once CPU at a time.  Currently
all of the Freescale boards msut pass the MPIC_SINGLE_DEST_CPU flag to
mpic_alloc(), but that information should really be present in the
device-tree.

Older board code can't rely on the device-tree having the property set,
but newer platforms won't need it manually specified in the code.

[BenH: Remove unrelated changes, folded in a different patch]
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The MPIC code checks for a "big-endian" property and sets the flag
MPIC_BIG_ENDIAN if one is present, although prior to the "mpic->flags"
fixup that would never have worked anways.

Unfortunately, even now that it works properly, the Freescale mpic
device-node (the "PowerQUICC-III"-compatible one) does not specify it,
so all of the board ports need to manually pass it to mpic_alloc().

Document the flag and add it to the pq3 device tree.  Existing code will
still need to pass the MPIC_BIG_ENDIAN flag because their dtb may not
have this property, but new platforms shouldn't need to do so.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The mpic_alloc() function takes a "flags" parameter and assigns it into
the mpic->flags variable fairly early on, but several later pieces of
code detect various device-tree properties and save them into the
"mpic->flags" variable (EG: "big-endian" => MPIC_BIG_ENDIAN).

Unfortunately, a number of codepaths (including several which test the
flag MPIC_BIG_ENDIAN!) test "flags" instead of "mpic->flags", and get
wrong answers as a result.

Consolidate the device-tree flag tests early in mpic_alloc() and change
all of the checks after "mpic->flags" is init'ed to use "mpic->flags".

[BenH: Fixed up use of mpic->node before it's initialized]
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

(And define it properly for x86-32, which had its 'current_task'
declaration in separate from x86-64)

Bitten by my dislike for modules on the machines I use, and the fact
that apparently nobody else actually wanted to test the patches I sent
out.

Snif. Nobody else cares.

Anyway, we probably should uninline the 'kernel_fpu_begin()' function
that is what modules actually use and that references this, but this is
the minimal fix for now.
Reported-by: Josh Boyer <jwboyer@gmail.com>
Reported-and-tested-by: Jongman Heo <jongman.heo@samsung.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Assorted fixes, sat in -next for a week or so...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ocfs2: deal with wraparounds of i_nlink in ocfs2_rename()
  vfs: fix compat_sys_stat() handling of overflows in st_nlink
  quota: Fix deadlock with suspend and quotas
  vfs: Provide function to get superblock and wait for it to thaw
  vfs: fix panic in __d_lookup() with high dentry hashtable counts
  autofs4 - fix lockdep splat in autofs
  vfs: fix d_inode_lookup() dentry ref leak

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  [S390] correct ktime to tod clock comparator conversion
  [S390] 3215 deadlock with tty_wakeup
  [S390] incorrect PageTables counter for kvm page tables
  [S390] idle: avoid RCU usage in extended quiescent state

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  digsig: changed type of the timestamp

This makes us recognize when we try to restore FPU state that matches
what we already have in the FPU on this CPU, and avoids the restore
entirely if so.

To do this, we add two new data fields:

 - a percpu 'fpu_owner_task' variable that gets written any time we
   update the "has_fpu" field, and thus acts as a kind of back-pointer
   to the task that owns the CPU.  The exception is when we save the FPU
   state as part of a context switch - if the save can keep the FPU
   state around, we leave the 'fpu_owner_task' variable pointing at the
   task whose FP state still remains on the CPU.

 - a per-thread 'last_cpu' field, that indicates which CPU that thread
   used its FPU on last.  We update this on every context switch
   (writing an invalid CPU number if the last context switch didn't
   leave the FPU in a lazily usable state), so we know that *that*
   thread has done nothing else with the FPU since.

These two fields together can be used when next switching back to the
task to see if the CPU still matches: if 'fpu_owner_task' matches the
task we are switching to, we know that no other task (or kernel FPU
usage) touched the FPU on this CPU in the meantime, and if the current
CPU number matches the 'last_cpu' field, we know that this thread did no
other FP work on any other CPU, so the FPU state on the CPU must match
what was saved on last context switch.

In that case, we can avoid the 'f[x]rstor' entirely, and just clear the
CR0.TS bit.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This inlines what is usually just a couple of instructions, but more
importantly it also fixes the theoretical error case (can that FPU
restore really ever fail? Maybe we should remove the checking).

We can't start sending signals from within the scheduler, we're much too
deep in the kernel and are holding the runqueue lock etc.  So don't
bother even trying.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This makes sure we clear the FPU usage counter for newly created tasks,
just so that we start off in a known state (for example, don't try to
preload the FPU state on the first task switch etc).

It also fixes a thinko in when we increment the fpu_counter at task
switch time, introduced by commit 34ddc81a ("i387: re-introduce FPU
state preloading at context switch time").  We should increment the
*new* task fpu_counter, not the old task, and only if we decide to use
that state (whether lazily or preloaded).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

time_t was used in the signature and key packet headers,
which is typedef of long and is different on 32 and 64 bit architectures.
Signature and key format should be independent of architecture.
Similar to GPG, I have changed the type to uint32_t.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: James Morris <jmorris@namei.org>

These are the bug fixes that have accumulated since 3.3-rc3 in arm-soc.
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.

The notable ones are:

* The at91 ata drivers both broke because of an earlier cleanup patch that
  some other patches were based on. Jean-Christophe decided to remove
  the legacy at91_ide driver and fix the new-style at91-pata driver while
  keeping the cleanup patch. I almost rejected the patches for being too
  late and too big but in the end decided to accept them because they
  fix a regression.

* A patch fixing build breakage from the sysdev-to-device conversion
  colliding with other changes touches a number of mach-s3c files.

* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
  is a mechanical change that unfortunately touches a lot of lines
  that should up in the diffstat.

* tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
  ARM: at91: drop ide driver in favor of the pata one
  pata/at91: use newly introduced SMC accessors
  ARM: at91: add accessor to manage SMC
  ARM: at91:rtc/rtc-at91sam9: ioremap register bank
  ARM: at91: USB AT91 gadget registration for module
  ep93xx: fix build of vision_ep93xx.c
  ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
  ARM: orion: Fix USB phy for orion5x.
  ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
  ARM: EXYNOS: Add cpu-offset property in gic device tree node
  ARM: EXYNOS: Bring exynos4-dt up to date
  ARM: OMAP3: cm-t35: fix section mismatch warning
  ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
  ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
  ARM: tegra: paz00: fix wrong SD1 power gpio
  i2c: tegra: Add devexit_p() for remove
  ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
  ARM: EXYNOS: Correct framebuffer window size on Nuri board
  ARM: SAMSUNG: Fix missing api-change from subsys_interface change
  ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
  ...

1) VETH_INFO_PEER netlink attribute needs to have it's size validated,
   from Thomas Graf.

2) 'poll' module option of bnx2x driver crashes the machine, just remove
   it.  From Michal Schmidt.

3) ks8851_mll driver reads the irq number from two places, but only
   initializes one of them, oops.  Use only one location and fix this
   problem, from Jan Weitzel.

4) Fix buffer overrun and unicast sterring bugs in mellanox mlx4 driver,
   from Eugenia Emantayev.

5) Swapped kcalloc() args in RxRPC and mlx4, from Axel Lin.

6) PHY MDIO device name regression fixes from Florian Fainelli.

7) If the wake event IRQ line is different from the netdevice one, we
   have to properly route it to the stmmac interrupt handler.  From
   Francesco Virlinzi.

8) Fix rwlock lock initialization ordering bug in mac80211, from
   Mohammed Shafi Shajakhan.

9) TCP lost_cnt can get out of sync, and in fact go negative, in certain
   circumstances.  Fix the way we specify what sequence range to operate
   on in tcp_sacktag_one() to fix this bug.  From Neal Cardwell.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
  net/ethernet: ks8851_mll fix irq handling
  veth: Enforce minimum size of VETH_INFO_PEER
  stmmac: update the driver version to Feb 2012 (v2)
  stmmac: move hw init in the probe (v2)
  stmmac: request_irq when use an ext wake irq line (v2)
  stmmac: do not discard frame on dribbling bit assert
  ipheth: Add iPhone 4S
  mlx4: add unicast steering entries to resource_tracker
  mlx4: fix QP tree trashing
  mlx4: fix buffer overrun
  3c59x: shorten timer period for slave devices
  netpoll: netpoll_poll_dev() should access dev->flags
  RxRPC: Fix kcalloc parameters swapped
  bnx2x: remove the 'poll' module option
  tcp: fix tcp_shifted_skb() adjustment of lost_cnt_hint for FACK
  ks8851: Fix NOHZ local_softirq_pending 08 warning
  bnx2x: fix bnx2x_storm_stats_update() on big endian
  ixp4xx-eth: fix PHY name to match MDIO bus name
  octeon: fix PHY name to match MDIO bus name
  fec: fix PHY name to match fixed MDIO bus name
  ...

Fixes a bootstrapping issue for some registers when a less commonly used
method for register cache initialisation is used.  Only affects a fairly
small proportion of users that both don't use explicit register defaults
and do use the cache.

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Fix cache defaults initialization from raw cache defaults

Merge tag 'ecryptfs-3.3-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Fixes maximum filename length and filesystem type reporting in statfs() calls
and also fixes stale inode mode bits on eCryptfs inodes after a POSIX ACL was
set on the lower filesystem's inode.

* tag 'ecryptfs-3.3-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  ecryptfs: remove the second argument of k[un]map_atomic()
  eCryptfs: Copy up lower inode attrs after setting lower xattr
  eCryptfs: Improve statfs reporting

pinctrl fixes for v3.3

* tag 'pinctrl-for-torvalds-20120216' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: restore pin naming

Here are a few more fixes for powerpc.  Some are regressions, the rest
is simple/obvious/nasty enough that I deemed it good to go now.

Here's also step one of deprecating legacy iSeries support: we are
removing it from the main defconfig.

Nobody seems to be using it anymore and the code is nasty to maintain,
(involves horrible hacks in various low level areas of the kernel) so we
plan to actually rip it out at some point.  For now let's just avoid
building it by default.  Stephen will proceed to do the actual removal
later (probably 3.4 or 3.5).

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/perf: power_pmu_start restores incorrect values, breaking frequency events
  powerpc/adb: Use set_current_state()
  powerpc: Disable interrupts early in Program Check
  powerpc: Remove legacy iSeries from ppc64_defconfig
  powerpc/fsl/pci: Fix PCIe fixup regression
  powerpc: Fix kernel log of oops/panic instruction dump

One regression fix for SR-IOV on PPC and a couple of misc fixes from
Yinghai.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
  PCI: Fix pci cardbus removal
  PCI: set pci sriov page size before reading SRIOV BAR
  PCI: workaround hard-wired bus number V2

3 radeon fixes, I have some exynos fixes to push later but I'll queue
them separately once I've looked them over a bit.

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms: fix MSI re-arm on rv370+
  drm/radeon/kms/atom: bios scratch reg handling updates
  drm/radeon/kms: drop lock in return path of radeon_fence_count_emitted.

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: sha512 - use standard ror64()

After all the FPU state cleanups and finally finding the problem that
caused all our FPU save/restore problems, this re-introduces the
preloading of FPU state that was removed in commit b3b0870e ("i387:
do not preload FPU state at task switch time").

However, instead of simply reverting the removal, this reimplements
preloading with several fixes, most notably

 - properly abstracted as a true FPU state switch, rather than as
   open-coded save and restore with various hacks.

   In particular, implementing it as a proper FPU state switch allows us
   to optimize the CR0.TS flag accesses: there is no reason to set the
   TS bit only to then almost immediately clear it again.  CR0 accesses
   are quite slow and expensive, don't flip the bit back and forth for
   no good reason.

 - Make sure that the same model works for both x86-32 and x86-64, so
   that there are no gratuitous differences between the two due to the
   way they save and restore segment state differently due to
   architectural differences that really don't matter to the FPU state.

 - Avoid exposing the "preload" state to the context switch routines,
   and in particular allow the concept of lazy state restore: if nothing
   else has used the FPU in the meantime, and the process is still on
   the same CPU, we can avoid restoring state from memory entirely, just
   re-expose the state that is still in the FPU unit.

   That optimized lazy restore isn't actually implemented here, but the
   infrastructure is set up for it.  Of course, older CPU's that use
   'fnsave' to save the state cannot take advantage of this, since the
   state saving also trashes the state.

In other words, there is now an actual _design_ to the FPU state saving,
rather than just random historical baggage.  Hopefully it's easier to
follow as a result.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This moves the bit that indicates whether a thread has ownership of the
FPU from the TS_USEDFPU bit in thread_info->status to a word of its own
(called 'has_fpu') in task_struct->thread.has_fpu.

This fixes two independent bugs at the same time:

 - changing 'thread_info->status' from the scheduler causes nasty
   problems for the other users of that variable, since it is defined to
   be thread-synchronous (that's what the "TS_" part of the naming was
   supposed to indicate).

   So perfectly valid code could (and did) do

	ti->status |= TS_RESTORE_SIGMASK;

   and the compiler was free to do that as separate load, or and store
   instructions.  Which can cause problems with preemption, since a task
   switch could happen in between, and change the TS_USEDFPU bit. The
   change to TS_USEDFPU would be overwritten by the final store.

   In practice, this seldom happened, though, because the 'status' field
   was seldom used more than once, so gcc would generally tend to
   generate code that used a read-modify-write instruction and thus
   happened to avoid this problem - RMW instructions are naturally low
   fat and preemption-safe.

 - On x86-32, the current_thread_info() pointer would, during interrupts
   and softirqs, point to a *copy* of the real thread_info, because
   x86-32 uses %esp to calculate the thread_info address, and thus the
   separate irq (and softirq) stacks would cause these kinds of odd
   thread_info copy aliases.

   This is normally not a problem, since interrupts aren't supposed to
   look at thread information anyway (what thread is running at
   interrupt time really isn't very well-defined), but it confused the
   heck out of irq_fpu_usable() and the code that tried to squirrel
   away the FPU state.

   (It also caused untold confusion for us poor kernel developers).

It also turns out that using 'task_struct' is actually much more natural
for most of the call sites that care about the FPU state, since they
tend to work with the task struct for other reasons anyway (ie
scheduling).  And the FPU data that we are going to save/restore is
found there too.

Thanks to Arjan Van De Ven <arjan@linux.intel.com> for pointing us to
the %esp issue.

Cc: Arjan van de Ven <arjan@linux.intel.com>
Reported-and-tested-by: Raphael Prevost <raphael@buro.asia>
Acked-and-tested-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The conversion of the ktime to a value suitable for the clock comparator
does not take changes to wall_to_monotonic into account. In fact the
conversion just needs the boot clock (sched_clock_base_cc) and the
total_sleep_time.

This is applicable to 3.2+ kernels.

CC: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The 3215 driver calls tty_wakeup from irq context while holding the
device spinlock. If printk is called by any function on the callchain
starting from tty_wakeup the system deadlocks on the device spinlock.
Using a tasklet to call tty_wakup solves the problem.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The page_table_free_pgste function is used for kvm processes to free page
tables that have the pgste extension. It calls pgtable_page_ctor instead of
pgtable_page_dtor which increases NR_PAGETABLE instead of decreasing it.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Avoid calling wake_up() from our NMI "bottom halve" from RCU extended
quiescent state in idle. wake_up() has RCU read-side critical sections
but this will be completely ignored by RCU if the cpu is in extended
quiescent state.
Which means that whatever object is being accessed from within the
read-side critical section can be freed concurrently from a different
cpu.
So make sure we leave extended quiescent state before calling wake_up().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is
pending.  In order to not leak FIP state from one process to another, we
need to do a floating point load after the fxsave of the old process,
and before the fxrstor of the new FPU state.  That resets the state to
the (uninteresting) kernel load, rather than some potentially sensitive
user information.

We used to do this directly after the FPU state save, but that is
actually very inconvenient, since it

 (a) corrupts what is potentially perfectly good FPU state that we might
     want to lazy avoid restoring later and

 (b) on x86-64 it resulted in a very annoying ordering constraint, where
     "__unlazy_fpu()" in the task switch needs to be delayed until after
     the DS segment has been reloaded just to get the new DS value.

Coupling it to the fxrstor instead of the fxsave automatically avoids
both of these issues, and also ensures that we only do it when actually
necessary (the FP state after a save may never actually get used).  It's
simply a much more natural place for the leaked state cleanup.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>