- 14 Sep, 2022 8 commits
-
-
Douglas Anderson authored
There have been a few changes since the patch ("arm64: dts: qcom: Add LTE SKUs for sc7280-villager family") * New firmware reports LTE boards as "SKU 512" now. Old firmware will still report "SKU 0", but that's all pre-production and everyone will update. * It's been relaized that no "-rev0" boards were ever built that were WiFi-only. Thus we don't two entries for -rev0. Adjust the organization a bit. Signed-off-by:Douglas Anderson <dianders@chromium.org> Signed-off-by:
Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220829084732.2.I22e256d1ebac577a91fac44d1d12919be7111cd4@changeid
-
Douglas Anderson authored
There have been a few changes since the patch ("dt-bindings: arm: qcom: document sc7280 and villager board"). * New firmware reports LTE boards as "SKU 512" now. Old firmware will still report "SKU 0", but that's all pre-production and everyone will update. * It's been relaized that no "-rev0" boards were ever built that were WiFi-only. Thus we don't two entries for -rev0. Signed-off-by: -
Matthias Kaehlcke authored
Add nodes for the onboard USB hub on herobrine devices. Remove the 'always-on' property from the hub regulator, since the regulator is now managed by the onboard_usb_hub driver. This requires "CONFIG_USB_ONBOARD_HUB=y". Signed-off-by:
Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
-
Matthias Kaehlcke authored
Add nodes for the onboard USB hub on trogdor devices. Remove the 'always-on' property from the hub regulator, since the regulator is now managed by the onboard_usb_hub driver. For anyone using trogdor-based devices on Linux, it should be noted that this requires "CONFIG_USB_ONBOARD_HUB=y". Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema requires SDHCI reg names to be hc/core without "_mem" suffix, just like TXT bindings were expecting before the conversion. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by:
-
Dmitry Baryshkov authored
On SM8250 each group of MSI interrupts is mapped to the separate host interrupt. Describe each of interrupts in the device tree for PCIe0 host. Tested on Qualcomm RB5 platform with first group of MSI interrupts being used by the PME and attached ath11k WiFi chip using second group of MSI interrupts. Reviewed-by:
Johan Hovold <johan+linaro@kernel.org> Reviewed-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by:
-
Dmitry Baryshkov authored
Add #clock-cells property to the HDMI PHY device node to let other nodes resolve the hdmipll clock. While we are at it, also add the XO clock to the device node. Acked-by:
-
Yassine Oudjana authored
Replace DAI indices in codec nodes with definitions from the WCD9335 DT bindings for devices that use WCD9335. Signed-off-by:
Yassine Oudjana <y.oudjana@protonmail.com> Acked-by:
-
- 13 Sep, 2022 32 commits
-
-
Krzysztof Kozlowski authored
The TCSR mutex bindings allow device to be described only with address space (so it uses MMIO, not syscon regmap). This seems reasonable as TCSR mutex is actually a dedicated IO address space and it also fixes DT schema checks: qcom/msm8994-sony-xperia-kitakami-suzuran.dtb: hwlock: 'reg' is a required property qcom/msm8994-sony-xperia-kitakami-suzuran.dtb: hwlock: 'syscon' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
The TCSR mutex bindings allow device to be described only with address space (so it uses MMIO, not syscon regmap). This seems reasonable as TCSR mutex is actually a dedicated IO address space and it also fixes DT schema checks: qcom/ipq6018-cp01-c1.dtb: hwlock: 'reg' is a required property qcom/ipq6018-cp01-c1.dtb: hwlock: 'syscon' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
TCSR syscon node should come with dedicated compatible. Signed-off-by:
-
Krzysztof Kozlowski authored
TCSR syscon node should come with dedicated compatible. Signed-off-by:
-
Krzysztof Kozlowski authored
TCSR syscon node should come with dedicated compatible. Signed-off-by:
-
Krzysztof Kozlowski authored
TCSR syscon node should come with dedicated compatible. Signed-off-by:
-
Krzysztof Kozlowski authored
There are 174 GPIOs in SC7280. Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Krzysztof Kozlowski authored
The pin configuration is selected with "pins", not "pin" property. Fixes: 1209e924 ("arm64: dts: qcom: sm8350-sagami: Enable and populate I2C/SPI nodes") Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Judy Hsiao authored
Fix the DMIC no sound issue of villager-r1 by using "PP1800_L2C" as the DMIC power source to match the hardware schematic. This patch: 1. set vdd-micb-supply to PP1800_L2C as the MIC Bias voltage regulator. 2. In audio-routing, set VA DMIC01~VA DMIC03 to use the vdd-micb-supply setting. Co-developed-by:Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com> Signed-off-by:
Judy Hsiao <judyhsiao@chromium.org> Reviewed-by:
-
Srinivasa Rao Mandadapu authored
Add dt nodes for sound card support on rev5+ (aka CRD 3.0/3.1) boards, which is using WCD9385 headset playback, capture, I2S speaker playback and DMICs via VA macro. Signed-off-by:
Venkata Prasad Potturu <quic_potturu@quicinc.com> Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add dt nodes for sound card support on revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards, which is using WCD9385 headset playback, capture, I2S speaker playback and DMICs via VA macro. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Enable lpass cpu node and add pin control and dai-links for audio on sc7280 based platforms of rev5+ (aka CRD 3.0/3.1) boards. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Enable lpass cpu node and add pin control and dai-links for audio on sc7280 based platforms of revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add lpass cpu node for audio on sc7280 based platforms. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add max98360a codec node for audio use case on all herobrine boards. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add max98360a codec node for audio use case on revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards. Add amp_en node for max98360a codec pin control. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add wcd9385 codec node for audio use case on CRD rev5+ (aka CRD 3.0/3.1) boards. Add tlmm gpio property for switching CTIA/OMTP Headset. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add wcd9385 codec node for audio use case on sc7280 based platforms of revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards. Add tlmm gpio property for switching CTIA/OMTP Headset. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Enable rx, tx and va macro codecs and soundwire nodes for CRD rev5+ (aka CRD 3.0/3.1) boards. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Enable rx, tx and va macro codecs and soundwire nodes on revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
SC7280 has VA, TX and RX macros with SoundWire Controllers to attach with external codecs using soundwire masters. Add these nodes for sc7280 based platforms audio use case. Signed-off-by:
-
Taniya Das authored
Support external mclk to interface external MI2S clocks for SC7280. Fixes: 4185b27b ("dt-bindings: clock: Add YAML schemas for LPASS clocks on SC7280") Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Taniya Das <quic_tdas@quicinc.com> Reviewed-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Taniya Das authored
Add support for LPASS audio clock gating for RX/TX/SWA core bus clocks for SC7280. Update reg property min/max items in YAML schema. Fixes: 4185b27b ("dt-bindings: clock: Add YAML schemas for LPASS clocks on SC7280") Acked-by:
-
Taniya Das authored
When this property is set, the remoteproc is used to boot the LPASS and therefore lpass_q6ss_ahbm_clk and lpass_q6ss_ahbs_clk clocks would be used to bring LPASS out of reset and the rest of the lpass clocks would be controlled directly by the remoteproc. This is a cleanup done to handle overlap of regmap of lpasscc and lpass_aon blocks. Signed-off-by:
Satya Priya <quic_c_skakit@quicinc.com> Reviewed-by:
-
Jimmy Chen authored
This adds LTE skus for villager device tree files. Signed-off-by:
Jimmy Chen <jinghung.chen3@hotmail.com> Reviewed-by:
Sibi Sankar <quic_sibis@quicinc.com> Signed-off-by:
-
Jimmy Chen authored
This adds sc7280-herobrine-villager-r1.dts for villager device tree files. Herobrine-r1 is exactly the same as -r0 except that it uses a different audio solution (it uses the same one as the CRD). Signed-off-by:
-
Jimmy Chen authored
This adds a LTE skus for Chromebook Villager to the yaml. Signed-off-by:
-
