This patch enables usb3_peri0 that uses usb3_phy0 to enable VBUS
detection for the USB3.0 peripheral.

The Salvator-X[S] has USB3.0 type-A connector and supplies VBUS
if USB3.0 host runs. So, you need a special cable for it, and
to stop the VBUS supplies from the board, after you installs
a gadget driver, you should run the following command to avoid
conflict VBUS supply:

	# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch enables usb3_phy0 node for Salvator-X[S].
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds USB3.0 PHY node for r8a7796.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds USB3.0 PHY node for r8a7795.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add reg properties to pciec[01] placeholder nodes

This is to stop the compiler complaining as follows:
$ make
...
  DTC     arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
  DTC     arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
  DTC     arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
  DTC     arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Move pmu_a5[73], timer and thermal-zones nodes from soc node to root node.
The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.

This problem is flagged by the compiler as follows:
$ make
...
  DTC     arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb
...
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pmu_a57 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
...
  DTC     arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb
...
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pmu_a57 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
...
  DTC     arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb
...
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pmu_a57 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
...
  DTC     arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb
...
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/pmu_a57 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
...
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Sort root sub-nodes alphabetically for allow for easier maintenance
of this file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Sort root sub-nodes alphabetically for allow for easier maintenance
of this file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Describe the GPIO used to reset the Ethernet PHY for EthernetAVB.
This allows the driver to reset the PHY during probe and after system
resume.

On ULCB, the enable pin of the regulator providing PHY power is always
pulled high, but the driver may still need to reset the PHY if this
wasn't done by the bootloader before.

Inspired by patches in the BSP for the individual Salvator-X/XS boards
by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the GPIO used to reset the Ethernet PHY for EthernetAVB.
This allows the driver to reset the PHY during probe and after system
resume.

This fixes Ethernet operation after resume from s2ram on Salvator-XS,
where the enable pin of the regulator providing PHY power is connected
to PRESETn, and PSCI powers down the SoC during system suspend.

On Salvator-X, the enable pin is always pulled high, but the driver may
still need to reset the PHY if this wasn't done by the bootloader
before.

Inspired by patches in the BSP for the individual Salvator-X/XS boards
by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Move pmu_a5[73], timer and thermal-zones nodes from soc node to root node.
The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.

This problem is flagged by the compiler as follows:
$ make
...
  DTC     arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pmu_a57 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
  DTC     arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dtb
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pmu_a57 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
  DTC     arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-kf.dtb
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pmu_a57 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
  DTC     arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/pmu_a57 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
  DTC     arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pmu_a57 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
  DTC     arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dtb
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pmu_a57 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
  DTC     arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb-kf.dtb
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pmu_a57 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Now that the commit 833bdb47 ("dt-bindings: power: add R8A77970 SYSC
power domain definitions") has hit Linus' tree, we can replace the  bare
numbers  (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Now that the commit ecadea00 ("dt-bindings: clock: Add R8A77970 CPG
core clock definitions") has hit Linus' tree, we  can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the V3M Starter Kit board dependent part of the EtherAVB
device node.

Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the initial device  tree for the V3M Starter Kit board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.

Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add IPMMU-RT to the Ethernet-AVB device node.

Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add r8a77995 IPMMU nodes and keep all disabled by default.

Based on work for the r8a7795 and r8a7796 by Magnus Damm
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Enable the r8a77970 device nodes for IPMMU-DS1, IPMMU-RT
and the shared IPMMU-MM device.

Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add IPMMU-RT to the Ethernet-AVB device node.

Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Hook up r8a77970 DMAC nodes to the IPMMU. In particular
SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.

Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add r8a77970 IPMMU nodes and keep all disabled by default.

Based on work for the r8a7796 by Magnus Damm
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Tested on Draak.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Sort includes used in r8a77970 DTS to improve maintainability
and for consistency with other R-Car DTS files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

This patch changes the number of GPIO bank 1 ports to 29 because GP-1-28
port pin of R8A7795 ES2.0 SoC support was added.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 291e0c49 ("arm64: dts: r8a7795: Add support for R-Car H3 ES2.0")
[geert: Keep 28 GPIOs on H3 ES1.x after r8a7795.dtsi sharing]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Adds CAN FD controller node for r8a77995.

Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Adds CAN controller nodes for r8a77995.

Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Adds external CAN clock node for r8a77995. This clock can be used as
fCAN clock of CAN and CAN FD controller.

Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Document clearly which SoC this DTS applies to, to distinguish from
Salvator-XS boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the ROHM BD9571MWV PMIC.

This was based on the example in the DT binding documentation, but using
IRQ0 instead of a GPIO interrupt, as that matches the schematics, and
because INTC-EX is a simpler block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable the r8a7795 device nodes for IPMMU-VI0, IPMMU-VP1, IPMMU-DS0,
IPMMU-DS1 and the shared IPMMU-MM device.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Enable the r8a7795 ES1.x device node for IPMMU-MP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add IPMMU-HC to the SATA device node.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add IPMMU-DS0 to the Ethernet-AVB device node.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Hook up the FCPVI devices to allow use of VSPI with IPMMU-VP.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Hook up the FCPVI devices to allow use of VSPI with
IPMMU-VP0 and IPMMU-VP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Hook up the FCPVB devices to allow use of VSPBC/VSPBD with
IPMMU-VP0 and IPMMU-VP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Hook up the FCPF devices to allow use of FDP1 with IPMMU-VP0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>