- 24 Feb, 2022 4 commits
-
-
Venkateswara Naralasetty authored
Target copies spectral report and CFR report through dbring to host for further processing. This mechanism involves ring and buffer management in the Host, FW, and uCode, where improper tail pointer update issues are seen. This dbring debug support help to debug such issues by tracking head and tail pointer movement along with the timestamp at which each buffer is received and replenished. Provide a debugfs interface to enalbe/disable dbring debug support and dump the dbring debug entries. Also introduced a new hardware param to add dbring debugfs support for few hardwares which are using dbings. Usage: echo <dbr_id> <val> > /sys/kernel/debug/ath11k/ipq8074_2/ mac0/enable_dbr_debug dbr_id: 0 for spectral and 1 for CFR val: 0 - disable, 1 - enable. Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Venkateswara Naralasetty <quic_vnaralas@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/1645366059-11798-1-git-send-email-quic_vnaralas@quicinc.com
-
Pradeep Kumar Chitrapu authored
Translate HE status to radiotap format. This uses HE radiotap definitions from include/net/ieee80211_radiotap.h. Co-developed-by:
Miles Hu <milehu@codeaurora.org> Signed-off-by:
Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by:
Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by:
-
Pradeep Kumar Chitrapu authored
Add new bitmasks and macro definitions required for parsing HE status tlvs. Decode HE status tlvs, which will used in dumping ppdu stats as well as updating radiotap headers. Co-developed-by:
-
Pradeep Kumar Chitrapu authored
This allows us to pass HE rates down into the stack. Co-developed-by:
John Crispin <john@phrozen.org> Signed-off-by:
-
- 21 Feb, 2022 11 commits
-
-
Baochen Qiang authored
We are seeing below warnings: kernel: [25393.301506] ath11k_pci 0000:01:00.0: failed to flush mgmt transmit queue 0 kernel: [25398.421509] ath11k_pci 0000:01:00.0: failed to flush mgmt transmit queue 0 kernel: [25398.421831] ath11k_pci 0000:01:00.0: dropping mgmt frame for vdev 0, is_started 0 this means ath11k fails to flush mgmt. frames because wmi_mgmt_tx_work has no chance to run in 5 seconds. By setting /proc/sys/kernel/hung_task_timeout_secs to 20 and increasing ATH11K_FLUSH_TIMEOUT to 50 we get below warnings: kernel: [ 120.763160] INFO: task wpa_supplicant:924 blocked for more than 20 seconds. kernel: [ 120.763169] Not tainted 5.10.90 #12 kernel: [ 120.763177] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kernel: [ 120.763186] task:wpa_supplicant state:D stack: 0 pid: 924 ppid: 1 flags:0x000043a0 kernel: [ 120.763201] Call Trace: kernel: [ 120.763214] __schedule+0x785/0x12fa kernel: [ 120.763224] ? lockdep_hardirqs_on_prepare+0xe2/0x1bb kernel: [ 120.763242] schedule+0x7e/0xa1 kernel: [ 120.763253] schedule_timeout+0x98/0xfe kernel: [ 120.763266] ? run_local_timers+0x4a/0x4a kernel: [ 120.763291] ath11k_mac_flush_tx_complete+0x197/0x2b1 [ath11k 13c3a9bf37790f4ac8103b3decf7ab4008ac314a] kernel: [ 120.763306] ? init_wait_entry+0x2e/0x2e kernel: [ 120.763343] __ieee80211_flush_queues+0x167/0x21f [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763378] __ieee80211_recalc_idle+0x105/0x125 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763411] ieee80211_recalc_idle+0x14/0x27 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763441] ieee80211_free_chanctx+0x77/0xa2 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763473] __ieee80211_vif_release_channel+0x100/0x131 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763540] ieee80211_vif_release_channel+0x66/0x81 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763572] ieee80211_destroy_auth_data+0xa3/0xe6 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763612] ieee80211_mgd_deauth+0x178/0x29b [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.763654] cfg80211_mlme_deauth+0x1a8/0x22c [cfg80211 8945aa5bc2af5f6972336665d8ad6f9c191ad5be] kernel: [ 120.763697] nl80211_deauthenticate+0xfa/0x123 [cfg80211 8945aa5bc2af5f6972336665d8ad6f9c191ad5be] kernel: [ 120.763715] genl_rcv_msg+0x392/0x3c2 kernel: [ 120.763750] ? nl80211_associate+0x432/0x432 [cfg80211 8945aa5bc2af5f6972336665d8ad6f9c191ad5be] kernel: [ 120.763782] ? nl80211_associate+0x432/0x432 [cfg80211 8945aa5bc2af5f6972336665d8ad6f9c191ad5be] kernel: [ 120.763802] ? genl_rcv+0x36/0x36 kernel: [ 120.763814] netlink_rcv_skb+0x89/0xf7 kernel: [ 120.763829] genl_rcv+0x28/0x36 kernel: [ 120.763840] netlink_unicast+0x179/0x24b kernel: [ 120.763854] netlink_sendmsg+0x393/0x401 kernel: [ 120.763872] sock_sendmsg+0x72/0x76 kernel: [ 120.763886] ____sys_sendmsg+0x170/0x1e6 kernel: [ 120.763897] ? copy_msghdr_from_user+0x7a/0xa2 kernel: [ 120.763914] ___sys_sendmsg+0x95/0xd1 kernel: [ 120.763940] __sys_sendmsg+0x85/0xbf kernel: [ 120.763956] do_syscall_64+0x43/0x55 kernel: [ 120.763966] entry_SYSCALL_64_after_hwframe+0x44/0xa9 kernel: [ 120.763977] RIP: 0033:0x79089f3fcc83 kernel: [ 120.763986] RSP: 002b:00007ffe604f0508 EFLAGS: 00000246 ORIG_RAX: 000000000000002e kernel: [ 120.763997] RAX: ffffffffffffffda RBX: 000059b40e987690 RCX: 000079089f3fcc83 kernel: [ 120.764006] RDX: 0000000000000000 RSI: 00007ffe604f0558 RDI: 0000000000000009 kernel: [ 120.764014] RBP: 00007ffe604f0540 R08: 0000000000000004 R09: 0000000000400000 kernel: [ 120.764023] R10: 00007ffe604f0638 R11: 0000000000000246 R12: 000059b40ea04980 kernel: [ 120.764032] R13: 00007ffe604f0638 R14: 000059b40e98c360 R15: 00007ffe604f0558 ... kernel: [ 120.765230] INFO: task kworker/u32:26:4239 blocked for more than 20 seconds. kernel: [ 120.765238] Not tainted 5.10.90 #12 kernel: [ 120.765245] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kernel: [ 120.765253] task:kworker/u32:26 state:D stack: 0 pid: 4239 ppid: 2 flags:0x00004080 kernel: [ 120.765284] Workqueue: phy0 ieee80211_iface_work [mac80211] kernel: [ 120.765295] Call Trace: kernel: [ 120.765306] __schedule+0x785/0x12fa kernel: [ 120.765316] ? find_held_lock+0x3d/0xb2 kernel: [ 120.765331] schedule+0x7e/0xa1 kernel: [ 120.765340] schedule_preempt_disabled+0x15/0x1e kernel: [ 120.765349] __mutex_lock_common+0x561/0xc0d kernel: [ 120.765375] ? ieee80211_sta_work+0x3e/0x1232 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.765390] mutex_lock_nested+0x20/0x26 kernel: [ 120.765416] ieee80211_sta_work+0x3e/0x1232 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.765430] ? skb_dequeue+0x54/0x5e kernel: [ 120.765456] ? ieee80211_iface_work+0x7b/0x339 [mac80211 335da900954f1c5ea7f1613d92088ce83342042c] kernel: [ 120.765485] process_one_work+0x270/0x504 kernel: [ 120.765501] worker_thread+0x215/0x376 kernel: [ 120.765514] kthread+0x159/0x168 kernel: [ 120.765526] ? pr_cont_work+0x5b/0x5b kernel: [ 120.765536] ? kthread_blkcg+0x31/0x31 kernel: [ 120.765550] ret_from_fork+0x22/0x30 ... kernel: [ 120.765867] Showing all locks held in the system: ... kernel: [ 120.766164] 5 locks held by wpa_supplicant/924: kernel: [ 120.766172] #0: ffffffffb1e63eb0 (cb_lock){++++}-{3:3}, at: genl_rcv+0x19/0x36 kernel: [ 120.766197] #1: ffffffffb1e5b1c8 (rtnl_mutex){+.+.}-{3:3}, at: nl80211_pre_doit+0x2a/0x15c [cfg80211] kernel: [ 120.766238] #2: ffff99f08347cd08 (&wdev->mtx){+.+.}-{3:3}, at: nl80211_deauthenticate+0xde/0x123 [cfg80211] kernel: [ 120.766279] #3: ffff99f09df12a48 (&local->mtx){+.+.}-{3:3}, at: ieee80211_destroy_auth_data+0x9b/0xe6 [mac80211] kernel: [ 120.766321] #4: ffff99f09df12ce0 (&local->chanctx_mtx){+.+.}-{3:3}, at: ieee80211_vif_release_channel+0x5e/0x81 [mac80211] ... kernel: [ 120.766585] 3 locks held by kworker/u32:26/4239: kernel: [ 120.766593] #0: ffff99f04458f948 ((wq_completion)phy0){+.+.}-{0:0}, at: process_one_work+0x19a/0x504 kernel: [ 120.766621] #1: ffffbad54b3cfe50 ((work_completion)(&sdata->work)){+.+.}-{0:0}, at: process_one_work+0x1c0/0x504 kernel: [ 120.766649] #2: ffff99f08347cd08 (&wdev->mtx){+.+.}-{3:3}, at: ieee80211_sta_work+0x3e/0x1232 [mac80211] With above info the issue is clear: First wmi_mgmt_tx_work is inserted to local->workqueue after sdata->work inserted, then wpa_supplicant acquires wdev->mtx in nl80211_deauthenticate and finally calls ath11k_mac_op_flush where it waits all mgmt. frames to be sent out by wmi_mgmt_tx_work. Meanwhile, sdata->work is blocked by wdev->mtx in ieee80211_sta_work, as a result wmi_mgmt_tx_work has no chance to run. Change to use ab->workqueue instead of local->workqueue to fix this issue. Signed-off-by:Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by:
-
Seevalamuthu Mariappan authored
In some scenarios like firmware crashes during init time and hardware gets restarted after qmi firmware ready event. During restart, ath11k_core_qmi_firmware_ready() returns timeout. But, this failure is not handled and ATH11K_FLAG_REGISTERED is set. When hardware restart completed, firmware sends firmware ready event again. Since ATH11K_FLAG_REGISTERED is already set, ath11k handles this as core restart. Inits are not done because of previous timeout. But ath11k_core_restart does deinit's which causes NULL pointer crash. Fix this by handling failure from ath11k_core_qmi_firmware_ready(). Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-00881-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Seevalamuthu Mariappan <quic_seevalam@quicinc.com> Signed-off-by:
-
Rameshkumar Sundaram authored
REO2SW ring descriptor is currently allocated in cacheable memory. While reaping reo ring entries on second trial after updating head pointer, first entry is not invalidated before accessing it. This results in host reaping and using cached descriptor which is already overwritten in memory by DMA device (HW). Since the contents of descriptor(buffer id, peer info and other information bits) are outdated host throws errors like below while parsing corresponding MSDU's and drops them. [347712.048904] ath11k_pci 0004:01:00.0: msdu_done bit in attention is not set [349173.355503] ath11k_pci 0004:01:00.0: frame rx with invalid buf_id 962 Move the try_again: label above ath11k_hal_srng_access_begin() so that first entry will be invalidated and prefetched. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Fixes: 6452f0a3 ("ath11k: allocate dst ring descriptors from cacheable memory") Signed-off-by:
Rameshkumar Sundaram <quic_ramess@quicinc.com> Signed-off-by:
-
Gustavo A. R. Silva authored
There is a regular need in the kernel to provide a way to declare having a dynamically sized set of trailing elements in a structure. Kernel code should always use “flexible array members”[1] for these cases. The older style of one-element or zero-length arrays should no longer be used[2]. [1] https://en.wikipedia.org/wiki/Flexible_array_member [2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays Link: https://github.com/KSPP/linux/issues/78Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Gustavo A. R. Silva authored
There is a regular need in the kernel to provide a way to declare having a dynamically sized set of trailing elements in a structure. Kernel code should always use “flexible array members”[1] for these cases. The older style of one-element or zero-length arrays should no longer be used[2]. [1] https://en.wikipedia.org/wiki/Flexible_array_member [2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays Link: https://github.com/KSPP/linux/issues/78Signed-off-by:
-
Gustavo A. R. Silva authored
There is a regular need in the kernel to provide a way to declare having a dynamically sized set of trailing elements in a structure. Kernel code should always use “flexible array members”[1] for these cases. The older style of one-element or zero-length arrays should no longer be used[2]. [1] https://en.wikipedia.org/wiki/Flexible_array_member [2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays Link: https://github.com/KSPP/linux/issues/78Signed-off-by:
-
Gustavo A. R. Silva authored
There is a regular need in the kernel to provide a way to declare having a dynamically sized set of trailing elements in a structure. Kernel code should always use “flexible array members”[1] for these cases. The older style of one-element or zero-length arrays should no longer be used[2]. [1] https://en.wikipedia.org/wiki/Flexible_array_member [2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays Link: https://github.com/KSPP/linux/issues/78Signed-off-by:
-
Jason A. Donenfeld authored
Hardware random number generators are supposed to use the hw_random framework. This commit turns ath9k's kthread-based design into a proper hw_random driver. Cc: Toke Høiland-Jørgensen <toke@redhat.com> Cc: Kalle Valo <kvalo@kernel.org> Cc: Rui Salvaterra <rsalvaterra@gmail.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com> Tested-by:
Rui Salvaterra <rsalvaterra@gmail.com> Acked-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
-
Wen Gong authored
The rddm_size is needed by firmware while mhi enter RDDM state, add it to support recovery when ath11k receive MHI_CB_EE_RDDM message. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by:
Wen Gong <quic_wgong@quicinc.com> Signed-off-by:
-
Carl Huang authored
This is to fix m3 buffer reuse issue as m3_mem->size isn't set to ZERO in free function, which leads invalid m3 downloading to firmware and firmware crashed. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by:
Carl Huang <quic_cjhuang@quicinc.com> Signed-off-by:
-
Wen Gong authored
ath11k_qmi_free_target_mem_chunk() and ath11k_qmi_m3_free() is static in qmi.c, they are needed for recovery, export them in a new function. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by:
-
- 14 Feb, 2022 5 commits
-
-
Minghao Chi (CGEL ZTE) authored
Replace zero-length array with flexible-array member and make use of the struct_size() helper in kmalloc(). For example: struct wcn36xx_hal_ind_msg { struct list_head list; size_t msg_len; u8 msg[]; }; Make use of the struct_size() helper instead of an open-coded version in order to avoid any potential type mistakes. Reported-by:Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn> Signed-off-by:
-
Karthikeyan Kathirvel authored
More than 20000 PPDU id jumping causing status ring and destination ring processing not sync. The status ring is processed and the destination ring is not processed. Since destination is not reaped for so long, backpressure occurs at the destination ring. To address this issue update the PPDU id with the latest PPDU, this will allow the destination ring to be reaped and will prevent the rings from getting out of sync. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2 Signed-off-by:
Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by:
-
Venkateswara Naralasetty authored
Radar detection fails in the secondary 80 MHz when the the AP's primary 80 MHz is in non-DFS region in 160 MHz. This is due to WMI channel flag WMI_CHAN_INFO_DFS_FREQ2 is not set properly in case of the primary 80 MHz is in non-DFS region. HALPHY detects the radar pulses in the secondary 80 MHz only when WMI_CHAN_INFO_DFS_FREQ2 is set. Fix this issue by setting WMI channel flag WMI_CHAN_INFO_DFS_FREQ2 based on the radar_enabled flag from the channel context. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Venkateswara Naralasetty authored
Fix WARN_ON() from ath11k_mac_update_vif_chan() if vdev is not up. Since change_chanctx can be called even before vdev_up from ieee80211_start_ap->ieee80211_vif_use_channel-> ieee80211_recalc_radar_chanctx. Do vdev stop followed by a vdev start in case of vdev is down. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Wen Gong authored
The rate_idx which passed to ath11k_debugfs_sta_add_tx_stats() by ath11k_dp_tx_update_txcompl() is not initialized, add initialization for it. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Fixes: 1b8bb94c ("ath11k: report tx bitrate for iw wlan station dump") Signed-off-by:
-
- 10 Feb, 2022 1 commit
-
-
Dan Carpenter authored
This code needs "channel" to be initialized to NULL for it to work correctly. Fixes: d6f27466 ("wcn36xx: Track the band and channel we are tuned to") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Bryan O'Donoghue <bryan.odonghue@linaro.org> Signed-off-by:
-
- 03 Feb, 2022 1 commit
-
-
Yang Li authored
Eliminate the follow smatch warnings: drivers/net/wireless/ath/wcn36xx/main.c:1394 wcn36xx_get_survey() warn: inconsistent indenting drivers/net/wireless/ath/wcn36xx/txrx.c:379 wcn36xx_rx_skb() warn: inconsistent indenting Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Signed-off-by:
-
- 01 Feb, 2022 3 commits
-
-
John Crispin authored
New debugfs files to manually add/delete/pause/resume TWT dialogs for test/debug purposes. The debugfs files expect the following parameters - Add dialog echo '<Peer_MAC> <Dialog_ID> <Wake_Interval_Usec> <Wake_Interval_Mantis> <Wake_Duration_Usec> <First_SP_Offset> <TWT_Command> <1:Broadcast /0:Individual> <1:Triggered / 0:Untriggered> <1:Unannounced /0:Announced> <1:Protected / 0:Unprotected>' > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/twt/add_dialog Example (Non-triggered and un-announced): echo '00:03:7F:20:13:52 1 102400 100 30720 20480 4 0 0 1 0' > /sys/kernel/debug/ieee80211/phy0/netdev:wlan0/twt/add_dialog - Delete dialog echo '<Peer_MAC> <Dialog_ID>' > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/twt/del_dialog - Pause dialog echo '<Peer_MAC> <Dialog_ID>' > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/twt/pause_dialog - Resume dialog echo '<Peer_MAC> <Dialog_ID> <SP_Offset_Usec> <Next_TWT_Size>' > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/twt/resume_dialog Example: echo '00:03:7F:20:13:52 1 2000000 3' > /sys/kernel/debug/ieee80211/phy0/netdev:wlan0/twt/resume_dialog Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01179-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Aloka Dixit <alokad@codeaurora.org> Signed-off-by:
-
John Crispin authored
These calls are used for debugging and will be required for WFA certification tests. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01179-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Seevalamuthu Mariappan authored
Add debugfs interface "fw_dbglog_config" to configure firmware log level. Configuration is done via WMI command WMI_DBGLOG_CFG_CMDID. Command to configure, echo "<dbglog_param> <values>" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config where dbglog_param can be, 1) WMI_DEBUG_LOG_PARAM_LOG_LEVEL - configure log level for a given module here, <values> = <0xaaaa00bb>, 'aaaa' - module id and 'bb' - loglevel 2) WMI_DEBUG_LOG_PARAM_VDEV_ENABLE - enable debug log for a given vdev here, <values> = vdev_id 3) WMI_DEBUG_LOG_PARAM_VDEV_DISABLE - disable debug log for a given vdev except ERROR logs here, <values> = vdev_id 4) WMI_DEBUG_LOG_PARAM_VDEV_ENABLE_BITMAP - set vdev enable bitmap here, <values> = vdev_enable_bitmap 5) WMI_DEBUG_LOG_PARAM_MOD_ENABLE_BITMAP - set a given log level to all the modules specified in the module bitmap. Command to configure for this log param, $ echo "5 <values> <module_id_index> <is_end>" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config here, <values> = <0xaaaaaaaa000000bb>, 'aaaaaaaa' - module bitmap and 'bb' - loglevel <module_id_index> = index of module bitmap. Max module id is 512. So, module_id_index is 0-15. <is_end> = to indicate if more configuration to follow. 6) WMI_DEBUG_LOG_PARAM_WOW_MOD_ENABLE_BITMAP - Wow mode specific logging enable. Command to configure for this log param, $ echo "6 <values> <module_id_index> <is_end>" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config here, <values> = <0xaaaaaaaa000000bb>, 'aaaaaaaa' - module bitmap and 'bb' - loglevel <module_id_index> = index of module bitmap. Max module id is 512. So, module_id_index is 0-15. <is_end> = to indicate if more configuration to follow. Sample command usage, To enable module WLAN_MODULE_WMI and log level ATH11K_FW_DBGLOG_VERBOSE, echo "1 0x10001" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config To enable module bit map from 32 to 63 and log level ATH11K_FW_DBGLOG_VERBOSE, echo "5 0xffffffff00000001 1 1" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
- 31 Jan, 2022 8 commits
-
-
Colin Ian King authored
Currently tx_params is being re-assigned with a new value and the previous setting IEEE80211_HT_MCS_TX_RX_DIFF is being overwritten. The assignment operator is incorrect, the original intent was to bit-wise or the value in. Fix this by replacing the = operator with |= instead. Kudos to Christian Lamparter for suggesting the correct fix. Fixes: fe8ee9ad ("carl9170: mac80211 glue and command interface") Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Cc: <Stable@vger.kernel.org> Acked-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Bryan O'Donoghue authored
The spread of capability between the three WiFi silicon parts wcn36xx supports is: wcn3620 - 802.11 a/b/g wcn3660 - 802.11 a/b/g/n wcn3680 - 802.11 a/b/g/n/ac We currently treat wcn3660 as wcn3620 thus limiting it to 2GHz channels. Fix this regression by ensuring we differentiate between all three parts. Fixes: 8490987b ("wcn36xx: Hook and identify RF_IRIS_WCN3680") Cc: stable@vger.kernel.org Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
-
Kalle Valo authored
If amss.bin was missing ath11k would crash during 'rmmod ath11k_pci'. The reason for that was that we were using mhi_async_power_up() which does not check any errors. But mhi_sync_power_up() on the other hand does check for errors so let's use that to fix the crash. I was not able to find a reason why an async version was used. ath11k_mhi_start() (which enables state ATH11K_MHI_POWER_ON) is called from ath11k_hif_power_up(), which can sleep. So sync version should be safe to use here. [ 145.569731] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN PTI [ 145.569789] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] [ 145.569843] CPU: 2 PID: 1628 Comm: rmmod Kdump: loaded Tainted: G W 5.16.0-wt-ath+ #567 [ 145.569898] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0067.2021.0528.1339 05/28/2021 [ 145.569956] RIP: 0010:ath11k_hal_srng_access_begin+0xb5/0x2b0 [ath11k] [ 145.570028] Code: df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 ec 01 00 00 48 8b ab a8 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 ea 48 c1 ea 03 <0f> b6 14 02 48 89 e8 83 e0 07 83 c0 03 45 85 ed 75 48 38 d0 7c 08 [ 145.570089] RSP: 0018:ffffc900025d7ac0 EFLAGS: 00010246 [ 145.570144] RAX: dffffc0000000000 RBX: ffff88814fca2dd8 RCX: 1ffffffff50cb455 [ 145.570196] RDX: 0000000000000000 RSI: ffff88814fca2dd8 RDI: ffff88814fca2e80 [ 145.570252] RBP: 0000000000000000 R08: 0000000000000000 R09: ffffffffa8659497 [ 145.570329] R10: fffffbfff50cb292 R11: 0000000000000001 R12: ffff88814fca0000 [ 145.570410] R13: 0000000000000000 R14: ffff88814fca2798 R15: ffff88814fca2dd8 [ 145.570465] FS: 00007fa399988540(0000) GS:ffff888233e00000(0000) knlGS:0000000000000000 [ 145.570519] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 145.570571] CR2: 00007fa399b51421 CR3: 0000000137898002 CR4: 00000000003706e0 [ 145.570623] Call Trace: [ 145.570675] <TASK> [ 145.570727] ? ath11k_ce_tx_process_cb+0x34b/0x860 [ath11k] [ 145.570797] ath11k_ce_tx_process_cb+0x356/0x860 [ath11k] [ 145.570864] ? tasklet_init+0x150/0x150 [ 145.570919] ? ath11k_ce_alloc_pipes+0x280/0x280 [ath11k] [ 145.570986] ? tasklet_clear_sched+0x42/0xe0 [ 145.571042] ? tasklet_kill+0xe9/0x1b0 [ 145.571095] ? tasklet_clear_sched+0xe0/0xe0 [ 145.571148] ? irq_has_action+0x120/0x120 [ 145.571202] ath11k_ce_cleanup_pipes+0x45a/0x580 [ath11k] [ 145.571270] ? ath11k_pci_stop+0x10e/0x170 [ath11k_pci] [ 145.571345] ath11k_core_stop+0x8a/0xc0 [ath11k] [ 145.571434] ath11k_core_deinit+0x9e/0x150 [ath11k] [ 145.571499] ath11k_pci_remove+0xd2/0x260 [ath11k_pci] [ 145.571553] pci_device_remove+0x9a/0x1c0 [ 145.571605] __device_release_driver+0x332/0x660 [ 145.571659] driver_detach+0x1e7/0x2c0 [ 145.571712] bus_remove_driver+0xe2/0x2d0 [ 145.571772] pci_unregister_driver+0x21/0x250 [ 145.571826] __do_sys_delete_module+0x30a/0x4b0 [ 145.571879] ? free_module+0xac0/0xac0 [ 145.571933] ? lockdep_hardirqs_on_prepare.part.0+0x18c/0x370 [ 145.571986] ? syscall_enter_from_user_mode+0x1d/0x50 [ 145.572039] ? lockdep_hardirqs_on+0x79/0x100 [ 145.572097] do_syscall_64+0x3b/0x90 [ 145.572153] entry_SYSCALL_64_after_hwframe+0x44/0xae Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by:
-
Kalle Valo authored
Mario reported that the kernel was crashing on suspend if ath11k was not able to find a board file: [ 473.693286] PM: Suspending system (s2idle) [ 473.693291] printk: Suspending console(s) (use no_console_suspend to debug) [ 474.407787] BUG: unable to handle page fault for address: 0000000000002070 [ 474.407791] #PF: supervisor read access in kernel mode [ 474.407794] #PF: error_code(0x0000) - not-present page [ 474.407798] PGD 0 P4D 0 [ 474.407801] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 474.407805] CPU: 2 PID: 2350 Comm: kworker/u32:14 Tainted: G W 5.16.0 #248 [...] [ 474.407868] Call Trace: [ 474.407870] <TASK> [ 474.407874] ? _raw_spin_lock_irqsave+0x2a/0x60 [ 474.407882] ? lock_timer_base+0x72/0xa0 [ 474.407889] ? _raw_spin_unlock_irqrestore+0x29/0x3d [ 474.407892] ? try_to_del_timer_sync+0x54/0x80 [ 474.407896] ath11k_dp_rx_pktlog_stop+0x49/0xc0 [ath11k] [ 474.407912] ath11k_core_suspend+0x34/0x130 [ath11k] [ 474.407923] ath11k_pci_pm_suspend+0x1b/0x50 [ath11k_pci] [ 474.407928] pci_pm_suspend+0x7e/0x170 [ 474.407935] ? pci_pm_freeze+0xc0/0xc0 [ 474.407939] dpm_run_callback+0x4e/0x150 [ 474.407947] __device_suspend+0x148/0x4c0 [ 474.407951] async_suspend+0x20/0x90 dmesg-efi-164255130401001: Oops#1 Part1 [ 474.407955] async_run_entry_fn+0x33/0x120 [ 474.407959] process_one_work+0x220/0x3f0 [ 474.407966] worker_thread+0x4a/0x3d0 [ 474.407971] kthread+0x17a/0x1a0 [ 474.407975] ? process_one_work+0x3f0/0x3f0 [ 474.407979] ? set_kthread_struct+0x40/0x40 [ 474.407983] ret_from_fork+0x22/0x30 [ 474.407991] </TASK> The issue here is that board file loading happens after ath11k_pci_probe() succesfully returns (ath11k initialisation happends asynchronously) and the suspend handler is still enabled, of course failing as ath11k is not properly initialised. Fix this by checking ATH11K_FLAG_QMI_FAIL during both suspend and resume. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Reported-by:
Mario Limonciello <mario.limonciello@amd.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=215504Signed-off-by:
-
Baochen Qiang authored
rx_desc_get_ldpc_support is missing in wcn6855_ops, resulting on WCN6855 a kernel crash after connecting to an AP and waiting for few minutes. Fix it by implementing WCN6855's version of this field and adding it to wcn6855_ops. Crash stack: [ 184.862605] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 184.862615] #PF: supervisor instruction fetch in kernel mode [ 184.862620] #PF: error_code(0x0010) - not-present page [ 184.862626] PGD 0 P4D 0 [ 184.862634] Oops: 0010 [#1] PREEMPT SMP PTI [ 184.862642] CPU: 1 PID: 0 Comm: swapper/1 Kdump: loaded Not tainted 5.16.0-wt-ath+ #1 [ 184.862651] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0059.2019.1112.1124 11/12/2019 [ 184.862656] RIP: 0010:0x0 [ 184.862669] Code: Unable to access opcode bytes at RIP 0xffffffffffffffd6. [ 184.862673] RSP: 0018:ffff9eedc003cca8 EFLAGS: 00010202 [ 184.862680] RAX: 0000000000000000 RBX: ffff9eedc003cd30 RCX: 0000000000000002 [ 184.862686] RDX: 0000000000000002 RSI: ffffffffc1773458 RDI: ffff8eb5843de240 [ 184.862692] RBP: ffff8eb59685a0e0 R08: 0000000000000001 R09: ffff8eb6fef2b000 [ 184.862700] R10: ffff9eedc003cd70 R11: ffff8eb5880a9ff0 R12: ffff8eb5843de240 [ 184.862707] R13: 0000000000000000 R14: 0000000000000008 R15: 0000000000000003 [ 184.862714] FS: 0000000000000000(0000) GS:ffff8eb6f6c40000(0000) knlGS:0000000000000000 [ 184.862723] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 184.862733] CR2: ffffffffffffffd6 CR3: 000000002f60a001 CR4: 00000000003706e0 [ 184.862743] Call Trace: [ 184.862751] <IRQ> [ 184.862759] ath11k_dp_rx_h_ppdu+0x210/0x350 [ath11k] [ 184.862841] ath11k_dp_rx_process_received_packets+0x1e6/0x6b0 [ath11k] [ 184.862891] ath11k_dp_process_rx+0x32d/0x3e0 [ath11k] Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Fixes: b3febdcc ("ath11k: add LDPC FEC type in 802.11 radiotap header") Signed-off-by:
-
Anilkumar Kolli authored
Add missing else statement in ath11k_dp_rx_process_mon_status() to fix below smatch warnings, drivers/net/wireless/ath/ath11k/dp_rx.c:3105 ath11k_dp_rx_process_mon_status() error: uninitialized symbol 'rx_buf_sz'. Fixes: ab18e3bc ("ath11k: Fix pktlog lite rx events") Reported-by:Anilkumar Kolli <quic_akolli@quicinc.com> Signed-off-by:
-
Venkateswara Naralasetty authored
Call netif_napi_del() from ath11k_ahb_free_ext_irq() to fix the following kernel panic when unload/load ath11k modules for few iterations. [ 971.201365] Unable to handle kernel paging request at virtual address 6d97a208 [ 971.204227] pgd = 594c2919 [ 971.211478] [6d97a208] *pgd=00000000 [ 971.214120] Internal error: Oops: 5 [#1] PREEMPT SMP ARM [ 971.412024] CPU: 2 PID: 4435 Comm: insmod Not tainted 5.4.89 #0 [ 971.434256] Hardware name: Generic DT based system [ 971.440165] PC is at napi_by_id+0x10/0x40 [ 971.445019] LR is at netif_napi_add+0x160/0x1dc [ 971.743127] (napi_by_id) from [<807d89a0>] (netif_napi_add+0x160/0x1dc) [ 971.751295] (netif_napi_add) from [<7f1209ac>] (ath11k_ahb_config_irq+0xf8/0x414 [ath11k_ahb]) [ 971.759164] (ath11k_ahb_config_irq [ath11k_ahb]) from [<7f12135c>] (ath11k_ahb_probe+0x40c/0x51c [ath11k_ahb]) [ 971.768567] (ath11k_ahb_probe [ath11k_ahb]) from [<80666864>] (platform_drv_probe+0x48/0x94) [ 971.779670] (platform_drv_probe) from [<80664718>] (really_probe+0x1c8/0x450) [ 971.789389] (really_probe) from [<80664cc4>] (driver_probe_device+0x15c/0x1b8) [ 971.797547] (driver_probe_device) from [<80664f60>] (device_driver_attach+0x44/0x60) [ 971.805795] (device_driver_attach) from [<806650a0>] (__driver_attach+0x124/0x140) [ 971.814822] (__driver_attach) from [<80662adc>] (bus_for_each_dev+0x58/0xa4) [ 971.823328] (bus_for_each_dev) from [<80663a2c>] (bus_add_driver+0xf0/0x1e8) [ 971.831662] (bus_add_driver) from [<806658a4>] (driver_register+0xa8/0xf0) [ 971.839822] (driver_register) from [<8030269c>] (do_one_initcall+0x78/0x1ac) [ 971.847638] (do_one_initcall) from [<80392524>] (do_init_module+0x54/0x200) [ 971.855968] (do_init_module) from [<803945b0>] (load_module+0x1e30/0x1ffc) [ 971.864126] (load_module) from [<803948b0>] (sys_init_module+0x134/0x17c) [ 971.871852] (sys_init_module) from [<80301000>] (ret_fast_syscall+0x0/0x50) Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.6.0.1-00760-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Venkateswara Naralasetty authored
Rename ath11k_ahb_ext_irq_config() to ath11k_ahb_config_ext_irq() for just symmetry with ath11k_ahb_free_ext_irq(). Signed-off-by:
-
- 28 Jan, 2022 7 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.18. Major changes: ath11k * add LDPC FEC type in 802.11 radiotap header * enable RX PPDU stats in monitor co-exist mode wcn36xx * implement survey reporting
-
Wen Gong authored
For the NL80211_REGDOM_SET_BY_USER hint from cfg80211, it set the new alpha2 code to ath11k, then ath11k send WMI_SET_INIT_COUNTRY_CMDID to firmware for all chips currently. When test with WCN6855/QCA6390 chips, this WMI CMD leads firmware crash. For AP based chips(ipq8074/qcn9074), WMI_SET_INIT_COUNTRY_CMDID is used to send to firmware, for STATION based chips(WCN6855/QCA6390), it need to use another WMI CMD WMI_SET_CURRENT_COUNTRY_CMDID. Add flag current_cc_support in hardware parameters, it is used to distinguish AP/STA platform. After that, the firmware will work normal and the regulatory feature works well for QCA6390/WCN6855. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by:
-
Wen Gong authored
When station connect to AP of 6 GHz with 40 MHz bandwidth, the TX is always stay 20 MHz, it is because the flag WMI_PEER_40MHZ is not set while peer assoc. Add the flag if remote peer is 40 MHz bandwidth. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Fixes: c3a7d7eb ("ath11k: add 6 GHz params in peer assoc command") Signed-off-by:
-
Pavel Skripkin authored
Syzbot reported 2 KMSAN bugs in ath9k. All of them are caused by missing field initialization. In htc_connect_service() svc_meta_len and pad are not initialized. Based on code it looks like in current skb there is no service data, so simply initialize svc_meta_len to 0. htc_issue_send() does not initialize htc_frame_hdr::control array. Based on firmware code, it will initialize it by itself, so simply zero whole array to make KMSAN happy Fail logs: BUG: KMSAN: kernel-usb-infoleak in usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430 usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430 hif_usb_send_regout drivers/net/wireless/ath/ath9k/hif_usb.c:127 [inline] hif_usb_send+0x5f0/0x16f0 drivers/net/wireless/ath/ath9k/hif_usb.c:479 htc_issue_send drivers/net/wireless/ath/ath9k/htc_hst.c:34 [inline] htc_connect_service+0x143e/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:275 ... Uninit was created at: slab_post_alloc_hook mm/slab.h:524 [inline] slab_alloc_node mm/slub.c:3251 [inline] __kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974 kmalloc_reserve net/core/skbuff.c:354 [inline] __alloc_skb+0x545/0xf90 net/core/skbuff.c:426 alloc_skb include/linux/skbuff.h:1126 [inline] htc_connect_service+0x1029/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:258 ... Bytes 4-7 of 18 are uninitialized Memory access of size 18 starts at ffff888027377e00 BUG: KMSAN: kernel-usb-infoleak in usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430 usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430 hif_usb_send_regout drivers/net/wireless/ath/ath9k/hif_usb.c:127 [inline] hif_usb_send+0x5f0/0x16f0 drivers/net/wireless/ath/ath9k/hif_usb.c:479 htc_issue_send drivers/net/wireless/ath/ath9k/htc_hst.c:34 [inline] htc_connect_service+0x143e/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:275 ... Uninit was created at: slab_post_alloc_hook mm/slab.h:524 [inline] slab_alloc_node mm/slub.c:3251 [inline] __kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974 kmalloc_reserve net/core/skbuff.c:354 [inline] __alloc_skb+0x545/0xf90 net/core/skbuff.c:426 alloc_skb include/linux/skbuff.h:1126 [inline] htc_connect_service+0x1029/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:258 ... Bytes 16-17 of 18 are uninitialized Memory access of size 18 starts at ffff888027377e00 Fixes: fb9987d0 ("ath9k_htc: Support for AR9271 chipset.") Reported-by: syzbot+f83a1df1ed4f67e8d8ad@syzkaller.appspotmail.com Signed-off-by:
Pavel Skripkin <paskripkin@gmail.com> Signed-off-by:
-
Jakub Kicinski authored
Pavel Begunkov says: ==================== udp/ipv6 optimisations Shed some weight from udp/ipv6. Zerocopy benchmarks over dummy showed ~5% tx/s improvement, should be similar for small payload non-zc cases. The performance comes from killing 4 atomics and a couple of big struct memcpy/memset. 1/10 removes a pair of atomics on dst refcounting for cork->skb setup, 9/10 saves another pair on cork init. 5/10 and 8/10 kill extra 88B memset and memcpy respectively. ==================== Link: https://lore.kernel.org/r/cover.1643243772.git.asml.silence@gmail.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Pavel Begunkov authored
Inline a part of ipv6_fixup_options() to avoid extra overhead on function call if opt is NULL. Signed-off-by:
Pavel Begunkov <asml.silence@gmail.com> Reviewed-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Pavel Begunkov authored
udpv6_sendmsg() doesn't need dst after calling ip6_make_skb(), so instead of taking an additional reference inside ip6_setup_cork() and releasing the initial one afterwards, we can hand over a reference into ip6_make_skb() saving two atomics. The only other user of ip6_setup_cork() is ip6_append_data() and it requires an extra dst_hold(). Signed-off-by:
-
