- 31 Jul, 2013 4 commits
-
-
David S. Miller authored
Jiri Pirko says: ==================== This patchset is based on patch by Narendra_K@Dell.com Once device which can change phys port id during its lifetime adopts this, NETDEV_CHANGEPHYSPORTID event will be added and driver will call call_netdevice_notifiers(NETDEV_NETDEV_CHANGEPHYSPORTID, dev) to propagate the change to userspace. v1->v2: as suggested by Ben, handle -EOPNOTSUPP in rtnl code (wrapped up ndo call) v2->v3: adjusted patch 1 commit message v3->v4: used "%phN" for sysfs printf as suggested by DaveM added igb/igbvf implementation as requested by Or Gerlitz v4->v5: used prandom_u32 to generate id in igb_probe removed duplicate code in ibgvf_probe pushed dev_err string into one line in igbvf_refresh_ppid v5->v6: use uuid_le_gen for generating 16-byte phys port id for igb/igbvf as suggested by BenH 1) Why do we need this, and why do existing facilities fail to provide a way to accomplish this? Currenty there's very hard to tell if two netdevs are using the same physical port. For sr-iov this can be get by sysfs. For other mechanisms, like NPAR there's very hard to do it (one must learn it from NIC BIOS). But even for sr-iov there's no way to say if two netdevs are using the same phys port when these are passed through to virtual guests. This patchset provides the generic way of letting this information know to userspace. This info can be used by apps like NetworkManager, teamd, Wicked, ovs daemon, etc, to do smarter bonding decisions. 2) Why is the physical port ID defined as a 32 byte opaque cookie? What formats and layouts need to be accomodated, and which influenced the design of the ID? For user to distinguish if two netdevs are using the same port, he only needs to compare their phys port ids. Nothing else is needed. This id has no structure for security reasons. VF should not know anything about PF. 3) Are IDs globally unique? Why or why not? If IDs should be globally unique, but only in certain cases, what exactly are those cases. Most of the time only uniqueness needed is in scope of single machine. There might be case when the id should be unique between couple of machines in virtualization environment. Given that for example for igb/igbvf 16B uuid is used, there is no problem for this case as well. But each driver can implement this differently focusing the hw capabilities and needs. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Acked-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
Narendra K <narendra_k@dell.com> Signed-off-by:
-
Jiri Pirko authored
Signed-off-by:
-
Jiri Pirko authored
This patch adds a ndo for getting physical port of the device. Driver which is aware of being virtual function of some physical port should implement this ndo. This is applicable not only for IOV, but for other solutions (NPAR, multichannel) as well. Basically if there is possible to have multiple netdevs on the single hw port. Signed-off-by:
-
- 30 Jul, 2013 20 commits
-
-
Thomas Petazzoni authored
Use the "swap descriptor" feature of the hardware to properly swap the descriptors when running in big endian mode. Since the swapping occurs on 64 bits words, we also need to provide a separate structure layout for the DMA descriptors between little endian and big endian mode, like is done in the mv643xx_eth driver. Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
-
Thomas Petazzoni authored
The macros used for the various fields of the RX and TX descriptions are currently declared next to those fields within the structure definitions of the RX and TX descriptors. However, in order to support big endian, we'll have to use the "swap descriptors" features of the hardware, which swaps every byte within each 64 bits word of the descriptors. This requires a separate definition of the RX and TX descriptor structures for little and big endian, as is done in the mv643xx_eth. Those macros can therefore no longer be defined inside those structures. Signed-off-by:
-
Thomas Graf authored
Unlike for IPv6, the IPv4 checksum functions are only available if CONFIG_INET is set. Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
Hannes Frederic Sowa authored
| If you want to test which effects syncookies have to your | network connections you can set this knob to 2 to enable | unconditionally generation of syncookies. Original idea and first implementation by Eric Dumazet. Cc: Florian Westphal <fw@strlen.de> Cc: David Miller <davem@davemloft.net> Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Mugunthan V N authored
Adding support for setting MAC address to cpsw device via ndo_set_mac_address Signed-off-by:
Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by:
-
Chris Metcalf authored
Signed-off-by:
Chris Metcalf <cmetcalf@tilera.com> Signed-off-by:
-
Andi Shyti authored
This patch reverts commit 80b45261 which was implementing a 'cancelled' functionality to notify that a cancelled request will not be replied. This implementation was not used anywhere and therefore removed. Signed-off-by:
Andi Shyti <andi@etezian.org> Signed-off-by:
-
Ivan Vecera authored
The driver uses dev_err when enabling of AER fails (e.g. PCIe AER is not supported). The dev_info is more appropriate to avoid console pollution. Cc: sathya.perla@emulex.com Cc: subbu.seetharaman@emulex.com Cc: ajit.khaparde@emulex.com Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Signed-off-by:
-
Nithin Sujir authored
Signed-off-by:
Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Nithin Sujir authored
The 5762 devices sometimes incorrectly treat udp fragments as RMCP packets and route to the APE. This patch sets the RX_MODE_IPV4_FRAG_FIX bit for these devices which enables the proper behaviour. Signed-off-by:
-
Nithin Sujir authored
The PTP_CAPABLE tg3 devices have a gpio output that is toggled when the free running counter matches a watchdog value. This patch adds support to set the watchdog and enable this feature. Since the output is controlled via bits in the EAV_REF_CLCK_CTL register, we have to read-modify-write it when we stop/resume. Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Nithin Sujir authored
Also remove the call to tg3_power_down_prepare() in tg3_power_down() since tg3_close() calls it. Signed-off-by:
-
Nithin Sujir authored
Previously, when the interface was brought down, the driver would set the power state to D3hot. In D3hot, we don't have access to the NVRAM. This patch removes the call to set the power state to PCI_D3hot in close. A following patch will implement the shutdown handler to properly set the D3hot state when the system is going down. Doing the above means that the TG3_PHYFLG_IS_LOW_POWER should not be checked to validate access to the NVRAM. Signed-off-by:
-
Nithin Sujir authored
During probe, the driver is incorrectly switching the power to Vaux on the 5717 and later devices. At this point, we are in D0 state and drawing maximum power. We also definitely have Vmain available. It doesn't make sense to switch to Vaux since it has a lesser maximum power draw and we might go over the limit. On a new system, we observe that not all ports are recognized in some of the slots with this call in place. Signed-off-by:
-
Michael Chan authored
Signed-off-by:
-
Eddie Wai authored
Completion status field should also be checked for non-zero error condition. Signed-off-by:
Eddie Wai <eddie.wai@broadcom.com> Signed-off-by:
-
Eddie Wai authored
Update TCP delayed ACK and timestamp options setup to match latest bnx2x firmware. Signed-off-by:
-
Eddie Wai authored
Without resetting it, the bnx2i driver cannot use different options for different iSCSI connections. Signed-off-by:
-
Michael Chan authored
Since unregister_netdevice_notifier() will replay the NETDEV_DOWN and NETDEV_UNREGISTER_EVENTS, the cnic_dev_list will be cleaned up automatically. The loop to cleanup the cnic_dev_list can be removed in cnic_release(). Signed-off-by:
-
Michael Chan authored
After this earlier commit to simplify probing: commit 4bd9b0ff cnic, bnx2x, bnx2: Simplify cnic probing. we can now reliably receive netdev events and we can simplify the handling of these events. We now remove the logic that tries to handle missed NETDEV_REGISTER events. This change will allow cleanup to be simplified in the next patch. We can now rely on the play back of netdev events during unregister_netdevice_notifier() to cleanup the structures. Signed-off-by:
-
- 29 Jul, 2013 3 commits
-
-
Yevgeny Petrilin authored
This commit adds new firmware command and new firmware event. The firmware raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ command. At the moment the supported operation is adding/removing multicast entries which are used by the firmware for handling NCSI traffic in B0 steering mode. Also, had to swap the order of mlx4_init_mcg_table() and mlx4_init_eq_table() to make sure that driver will get events only after resources are initialized to handle it. Signed-off-by:
Yevgeny Petrilin <yevgenyp@mellanox.com> Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.com> Signed-off-by:
Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by:
Amir Vadai <amirv@mellanox.com> Signed-off-by:
-
Eugenia Emantayev authored
Fix a race between BlueFlame flow and stamping in post send flow. Example: SW: Build WQE 0 on the TX buffer, except the ownership bit SW: Set ownership for WQE 0 on the TX buffer SW: Ring doorbell for WQE 0 SW: Build WQE 1 on the TX buffer, except the ownership bit SW: Set ownership for WQE 1 on the TX buffer HW: Read WQE 0 and then WQE 1, before doorbell was rung/BF was done for WQE 1 HW: Produce CQEs for WQE 0 and WQE 1 SW: Process the CQEs, and stamp WQE 0 and WQE 1 accordingly (on the TX buffer) SW: Copy WQE 1 from the TX buffer to the BF register - ALREADY STAMPED! HW: CQE error with index 0xFFFF - the BF WQE's control segment is STAMPED, so the BF index is 0xFFFF. Error: Invalid Opcode. As a result QP enters the error state and no traffic can be sent. Solution: When stamping - do not stamp last completed wqe. Signed-off-by:
-
Stephen Rothwell authored
Fixes this on PowerPC (at least): net/core/pktgen.c: In function 'fill_packet_ipv6': net/core/pktgen.c:2906:3: error: implicit declaration of function 'csum_ipv6_magic' [-Werror=implicit-function-declaration] udph->check = ~csum_ipv6_magic(&iph->saddr, &iph->daddr, udplen, IPPROTO_UDP, 0); ^ Signed-off-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
- 28 Jul, 2013 13 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-nextDavid S. Miller authored
Jeff Kirsher says: ==================== This series contains updates to e100 and e1000e. The e100 patch from Andy simply updates the netif_printk() to use %*ph to dump small buffers. The changes to e1000e include a fix from Dean Nelson to resolve a issue where a pci_clear_master() was accidentally dropped during a conflict resolution. Wei Young provides 2 patches, one removes an assignment of the default ring size because it was a duplicate. The second changes the packet split receive structure to use PS_PAGE_BUFFERS macro for the length so that problems won't occur when the length is changed. The remaining patches for e1000e are from Bruce Allan, where he provides a number of fixes and updates for I218. In addition, a fix for 82583 which can disappear off the PCIe bus, to resolve this, disable ASPM L1. Bruce also provides a fix to a previous commit (commit e60b22c5 e1000e: fix accessing to suspended device) so that devices are only taken out of runtime power management for those ethtool operations that must access device registers. ==================== Signed-off-by:
-
Hannes Frederic Sowa authored
v2: a) Also send ipv4 igmp messages with TC_PRIO_CONTROL Cc: William Manley <william.manley@youview.com> Cc: Lukas Tribus <luky-37@hotmail.com> Acked-by:
Benjamin LaHaise <bcrl@kvack.org> Signed-off-by:
-
Bruce Allan authored
The initialization of the PHY on I217/I218, while similar to 82579, must also check to see if the MAC and PHY are in the same mode (PCIe vs. SMBus) otherwise the PHY will be inaccessible by the MAC. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Tested-by:
Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
When the device is runtime suspended (e.g. when there is no link), do not wake it from D3 to read the PHY status; just set the values to typical power-on defaults as is done when runtime PM is not enabled and there is no link. Signed-off-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
-
Bruce Allan authored
The device IDs 0x15a0 and 0x15a1 are new SKUs that contain the same MAC as I217 and same PHY as I218. The device IDs 0x15a2 and 0x15a3 are the same as existing I218 SKUs. Signed-off-by:
-
Bruce Allan authored
A previous patch (commit e60b22c5 e1000e: fix accessing to suspended device) added .begin and .complete ethtool driver callbacks so that the device was resumed from Runtime Power Management (RPM) suspend state for all ethtool operations. This is overkill for operations which do not need to access any registers in the device. This patch makes it so that the device is taken out of RPM suspend only for those ethtool operations that must access device registers. Signed-off-by:
-
Bruce Allan authored
Tx hang is an unintended consequence of another workaround that is in the EEPROM for an issue with the firmware at 10Mbps when K1 (a power mode of the MAC-PHY interconnect) is enabled. The issue is resolved by setting appropriate Tx re-transmission timeouts in the PHY and associated K1 entry times in the MAC to allow enough transmissions to occur without triggering a Tx hang. A similar change is needed when linked at 10Mbps to improve latency. Signed-off-by:
-
Bruce Allan authored
Alter the packet buffer allocation accordingly. Signed-off-by:
-
Bruce Allan authored
The jumbo frame configuration in the MAC/PHY should be reverted on 82579 and newer parts when the interface is brought down (not just when the MTU is changed back to standard frame size) otherwise iAMT connections (e.g. SoL, IDE-R) will be dropped and cannot be re-acquired until the MTU is changed again. Signed-off-by:
-
Bruce Allan authored
The 82583 can disappear off the PCIe bus. This device is a modified 82574 which had the same problem which was fixed by disabling ASPM L1; disabling it on 82583 fixes the issue on this device. Signed-off-by:
-
Wei Yang authored
In structure e1000_rx_desc_packet_split, the size of wb.upper.length is defined by a digit. This may introduce some problem when the length is changed. This patch use the macro PS_PAGE_BUFFERS for the definition. And move the definition to hw.h. Signed-off-by:
Wei Yang <weiyang@linux.vnet.ibm.com> Tested-by:
-
Wei Yang authored
tx_ring/rx_ring size is assigned in function e1000_alloc_queues(), which is called by e1000_sw_init() in the early stage of e1000_probe(). This patch just remove the duplicate assignment of this default ring size value. Signed-off-by:
Gavin Shan <shangw@linux.vnet.ibm.com> Reviewed-by:
Da Yu Qiu <qiudayu@cn.ibm.com> Tested-by:
-
Dean Nelson authored
In attempting to resolve a minor merge conflict, commit e5f2ef7a (Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net) accidentally dropped a call to pci_clear_master() that was intended to remain in place. Commit 4e0855df (e1000e: fix pci-device enable-counter balance) replaced a call to pci_disable_device() by one to pci_clear_master(). And then commit 66148bab (e1000e: fix runtime power management transitions) deleted a number of lines starting two lines following that call. This patch restores the call to pci_clear_master() in __e1000_shutdown(). v2: added summary lines (enclosed in parens) following commit IDs Signed-off-by:
Dean Nelson <dnelson@redhat.com> Tested-by:
-
