twl4030_codec_audio and twl4030_codec_vibra_data has unused field.
In order to remove it, corresponding settings needs to be removed
from board files.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for vibra
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Added the KIM (Kernel initialization module for the
Shared Transport driver) device entry in the board file

Only the Blutooth enable GPIO is set for now
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On the OMAP3430LDP board, the ads7846 touchscreen controller
is powered by VAUX1 regulator (supplying 3.0v).
Fix this mapping in the board file, and hence prevent
the ads7846 driver init to fail with the below error..

ads7846 spi1.0: unable to get regulator: -19
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We should only call init_common_infrastructure and
init_common_devices from init_early.
Signed-off-by: Tony Lindgren <tony@atomide.com>

init_early hook runs too early for omap3_mux_init(), so the board
won't boot. Moved to init_machine, then it works just fine.
Signed-off-by: Radek Pilar <mrkva@mrkva.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add SI4713 FM transmitter supplies, platform data and setup to RX-51/N900.
It is connected to line output signals of TLV320AIC34 codec A part.
Driver can be either built-in or a module. It can be tuned with v4l2-ctl
from ivtv-utils. Following examples illustrate the use of it:

	v4l2-ctl -d /dev/radio0 --set-ctrl=mute=0 (power up)
	v4l2-ctl -d /dev/radio0 -f 107900 (tune 107.9 MHz)

	v4l2-ctl -d /dev/radio0 --set-ctrl=mute=1 (power down)
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix compile if MTD_NAND_OMAP2 is not selected
Signed-off-by: Tony Lindgren <tony@atomide.com>

We should only call init_common_infrastructure and
init_common_devices from init_early.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Conflicts:
	arch/arm/mach-omap2/board-3430sdp.c

This patch updated board files to replace platform_device_register or
platform_add_devices of DSS with omap_display_init(). This moves away
registration of DSS from board files into a common place.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

A new file display.c is introduced for display driver init, which adds a function
omap_display_init to do the DSS driver registration. This is the first step in moving
away registration of DSS from board files into a common place.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use driver name in regulator inits needed for display instead of using device
structure name.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for Display Sub System applicable for OMAP3430 and
OMAP36xx.  DSS is also considered as an IP as DISPC, RFBI and named as dss_core.
For all the IP modules in DSS, same clock is needed for enabling. Hwmod sees
DSS IPs as independent IPs, so same clock has to be repeated for .main_clk in
each IP.

This patch defines separate hwmod databases for OMAP3430ES1 and (OMAP3430ES2 and
OMAP36xx) as OMAP3430ES1 does not have IDLEST bit to poll on for dss IP, and also
the firewall regions are different between 3430es1 and later.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for OMAP2430 Display Sub System. Since DSS is also considered as an
IP as DISPC, RFBI, name it as dss_core.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for OMAP2420 Display Sub System,. Since DSS is also considered as an
IP as DISPC, RFBI, name it as dss_core.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Conflicts:
	arch/arm/mach-omap2/omap_hwmod_2430_data.c
	arch/arm/mach-omap2/omap_hwmod_3xxx_data.c

Since the timer1 is now started before the hwmod_init, we cannot
reset it and idle it anymore.

Add the appropriate flags to prevent the hwmod framework to do that.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP4 supports up to 5 MMC controllers, but only 3 of these were
initialized. MMC5 is used by wl12xx chip. So initialize MMC4 and MMC5.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add MMC5 support on PANDA, which has the wl1271 device hardwired to.

The wl1271 is a 4-wire, 1.8V, embedded SDIO WLAN device with an
external IRQ line, and power-controlled by a GPIO-based fixed regulator.

Based on the patch for mmc3/wl1271 device support for zoom by Ohad
Ben-Cohen <ohad@wizery.com>
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add a fixed regulator vmmc device to enable power control
of the wl1271 wlan device.

Based on the patch for zoom by Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Power to the wl12xx wlan device is controlled by a fixed regulator.
Boards that have the wl12xx should select REGULATOR_FIXED_VOLTAGE.
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc5 (fifth mmc controller) on the PANDA.

Based on the wlan board muxing for zoom3 by Ohad Ben-Cohen
<ohadb@ti.com>
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fixed regulators in twl6030 do not have set_voltage hook.
Regulator core returns -22 if set_voltage is NULL and apply_uV is set
while applying the constraint to set voltage resulting in failure during probe
of these regulators.
Do not set apply_uV for fixed regulators which don't have set_voltage.

machine_constraints_voltage: VANA: failed to apply 2100000uV constraint
twl_reg twl_reg.43: can't register VANA, -22
twl_reg: probe of twl_reg.43 failed with error -22
machine_constraints_voltage: VCXIO: failed to apply 1800000uV constraint
twl_reg twl_reg.44: can't register VCXIO, -22
twl_reg: probe of twl_reg.44 failed with error -22
machine_constraints_voltage: VDAC: failed to apply 1800000uV constraint
twl_reg twl_reg.45: can't register VDAC, -22
twl_reg: probe of twl_reg.45 failed with error -22
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

clean the regulator supply mapping data in the 3430sdp
board file (which is spread all over) by moving all
of them together.
Also use the REGULATOR_SUPPLY macro and remove instances
of mapping dev pointers at run time.
Additonally define all regulator_consumer_supply as
array's and use ARRAY_SIZE macro to define
num_consumer_supplies.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

- Add a rev attribute to identify various McSPI IP version.
- Add a dev_attr structure to provide the number of chipselect
  supported by the instance.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Allow OMAP4 ES2.1 and ES2.2 revisions to be recognized in the
omap4_check_revision() function.

Mainly, ES2.1 has fixes that allow LPDDR to be used at 100% OPP (400MHz).
ES2.2 additionally has a couple of power management fixes (to reduce
leakage), an I2C1 SDA line state fix, and a floating point write
corruption fix (cortex erratum).

Even though the current mainline support doesn't need to distinguish
between ES2.X versions, it's still useful to know the correct silicon
rev when issues are reported. Moreover, these id checks can be used by
power management code that selects suitable OPPs considering the
memory speed limitation on ES2.0.

For details about the silicon errata on OMAP4430, refer
http://focus.ti.com/pdfs/wtbu/SWPZ009A_OMAP4430_Errata_Public_vA.pdfSigned-off-by: Nishant Kamat <nskamat@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Change all occurences of printf() to pr_err().
Includes minor formatting changes as result of
this change.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes typos that were remaining after
the file and functions were renamed.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Declaration of exported function 'iopgtable_lookup_entry' is missing from
header file. Currently we have a sparse warning as it's not being used
externally. Adding its declaration to avoid such warning and allow its usage
in future.
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The current multiblock erase verify read timeout 100us is the maximum
for none-error case. If errors happen during multibock erase then
the specification recommends to run multiblock erase verify command
with maximum timeout 10ms (see specs. for KFM4G16Q2A and KFN8G16Q2A).

For the most common non-error case we wait 100us in udelay polling
loop. In case of timeout the interrupt mode is used to wait for the
command end.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OneNAND version ID may not give the highest frequency
supported and some OneNAND's have setup times that are
clock dependent.  Let the board provide that information.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OneNAND frequency is determined when calculating
GPMC timings.  Return that value instead of determining it
again in the OMAP OneNAND driver.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

104MHz needs a latency of 8 clock cycles and the VHF
flag must be set.  Also t_rdyo is specified as
"not applicable" so pick a lower value, and force at
least 1 clk between AVD High to OE Low.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On the OMAP3430SDP board, the ads7846 touchscreen controller
is powered by VAUX3 regulator (supplying 2.8v).
Fix this mapping in the board file, and hence prevent
the ads7846 driver init to fail with the below error..

ads7846 spi1.0: unable to get regulator: -19
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch overrides nand ecc layout and bad block descriptor (for 8-bit
device) to support hw ecc in romcode layout. So as to have in sync with ecc
layout throughout; i.e. x-loader, u-boot and kernel.

This enables to flash x-loader, u-boot, kernel, FS images from kernel itself
and compatiable with other tools.

This patch does not enables this feature by default and need to pass from
board file to enable for any board.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch makes it possible to select sw or hw (different layout options)
ecc scheme supported by omap nand driver.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Configure the FIFO THREASHOLD value different for read and write to keep busy
both filling and to drain out of FIFO at reading and writing.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>