This helps align resets / RX enable & disable / TX stop / start.
Locking around the PCU is important to ensure the hardware doesn't
get stale data when working with DMA'able data.

This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2Tested-by: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The PCU lock should be used to contend TX DMA as well,
this will be done next.

This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2Tested-by: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The new PCU lock is better placed so we can just contend
against that when trying to reset hardware.

This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2Tested-by: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This takes care that boolean types are properly assigned
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No need to inform about monitor interface changes to
firmware. Set the HW mode to monitor type based on mac80211
indication flag is sufficient.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use the new PCI PM and let the PCI core code handle the PCI-specific
details of power transitions.

Based on similarly titled ath9k patch posted by Rafael J. Wysocki.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>

This code seems to have been cut-n-pasted from alloc_ringmemory?
Anyway, it is useless.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1) Upload 5 GHz values when needed.
2) Do not upload all values on first init. Follow wl.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently we are canceling scan when changing BSSID. Behave the same
when changing association and beacon enablement, to avoid committing
rxon during scan in iwl_set_no_assoc().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Do not set power mode when scanning, and defer that when scan finish.
We still set power mode in force case i.e. when device is overheated.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Avoid sending commands to firmware (including commit_rxon) when scan
is pending and we are calling iwlagn_bt_traffic_change_work simultaneously.

Also comment some innocent race conditions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Almost anywhere in the code we avoid committing rxon while performing
scan, and make rxon commit when scan complete. However in some places
in the code we do not follow that rule. This patch fix that problem in
iwlagn_configure_filter().

Since we do not commit directly in iwl3945_configure_filter, we can
also do the same for agn, so I just remove iwlcore_commit_rxon()
function and add a comment. Also change comment for iwl3945.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

According to comment in iwl_bg_scan_completed, setting tx power should
be deferred during pending scan, but we are not doing this.

This patch change code to really defer setting tx power after scan
complete. Additionally refactor iwl_set_tx_power code and call
lib->send_tx_power() directly from iwlagn_commit_rxon.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On 5xxx and 6xxx change to send tx_power_cmd command synchronously,
to do not start other commands when setting tx power is pending.
We currently do the same for 4956 and 3945.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add WARN_ONCE when scanning is pending. Use STATUS_SCAN_HW bit since we
can have scan canceled or completed but STATUS_SCANNING bit still set.

v1 -> v2: replace EIO to EAGAIN
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

- reduce the number of retransmission attempts for sample rates
- sample lower rates less often
- do not use RTS/CTS for sampling frames
- increase the time between sampling attempts
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

According to documentation, AR_ExcessiveRetries, AR_Filtered and
AR_FIFOUnderrun are only valid if AR_FrmXmitOK is clear.

Not checking this might result in suboptimal FIFO settings, unnecessary
retransmissions, or other connectivity issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We have seen several DMA races when we race against
stopping and starting the PCU. I suspect that when
we cannot stop the PCU we may hit some of these same
races so warn against them for now but only when
debugging (CONFIG_ATH_DEBUG) is enabled.

If you run into this warning and are a developer,
please fix the cause of the warning. The potential
here, although I cannot prove yet, is that the DMA
engine can be confused and start writing to a buffer
that was already DMA'd before and at least the kernel
assumes is not being accessed by hardware anymore.

Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To be used to throw out warnings only for developers.
This can be used by some corner cases that developers
already know can be hit but developers want to address
so to avoid spewing out a warning this can only be
enabled with CONFIG_ATH_DEBUG enabled.

Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Everyone's doing it, its the cool thing.

Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the worst case you are seeing really odd things you want
more information than what is provided right now, for those
that insist and want debug info through CONFIG_CFG80211_REG_DEBUG
provide a print of when we are processing a channel and with what
regulatory rule.

Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This can help with debugging issues. You will only see
these with CONFIG_CFG80211_REG_DEBUG enabled.

Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After a module loads you will have loaded the world roaming regulatory
domain or a custom regulatory domain. Further regulatory hints are
welcomed and should be respected unless the regulatory hint is coming
from a country IE as the IEEE spec allows for a country IE to be a subset
of what is allowed by the local regulatory agencies.

So disable all channels that do not fit a regulatory domain sent
from a unless the hint is from a country IE and the country IE had
no information about the band we are currently processing.

This fixes a few regulatory issues, for example for drivers that depend
on CRDA and had no 5 GHz freqencies allowed were not properly disabling
5 GHz at all, furthermore it also allows users to restrict devices
further as was intended.

If you recieve a country IE upon association we will also disable the
channels that are not allowed if the country IE had at least one
channel on the respective band we are procesing.

This was the original intention behind this design but it was
completely overlooked...

Cc: David Quan <david.quan@atheros.com>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We should be enabling country IE hints for WIPHY_FLAG_STRICT_REGULATORY
even if we haven't yet recieved regulatory domain hint for the driver
if it needed one. Without this Country IEs are not passed on to drivers
that have set WIPHY_FLAG_STRICT_REGULATORY, today this is just all
Atheros chipset drivers: ath5k, ath9k, ar9170, carl9170.

This was part of the original design, however it was completely
overlooked...

Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is required later.

Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The following code is defined but never used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MMIO log traces obtained using the Broadcom wl hybrid driver show that
the RETRY_TIMEOUT register (0x41) in PCI configuration space is cleared
if non-zero. Similar code found in other drivers such as ipw2100 show
this operation is needed to keep PCI Tx retries from interfering with
C3 CPU state. There are no known cases where omission of this code has
caused a problem, but this patch is offered just in case such a situation
occurs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes this sparse warning:

  CHECK   drivers/net/wireless/ath/ath5k/base.c
drivers/net/wireless/ath/ath5k/base.c:569:6: warning: symbol
'ath5k_update_bssid_mask_and_opmode' was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes this sparse warning:

  CHECK   drivers/net/wireless/ath/key.c
drivers/net/wireless/ath/key.c:110:6: warning: symbol
'ath_hw_set_keycache_entry' was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes this sparse warning:

  CHECK   drivers/net/wireless/ath/key.c
drivers/net/wireless/ath/key.c:70:6: warning: symbol 'ath_hw_keysetmac' was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw_set_txpowerlimit gets an extra boolean parameter that - if set -
causes the rate txpower table and the regulatory limit to be calculated
and stored, without changing hardware registers.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The same is done for the older chip families as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Include the channel utilization (busy, rx, tx) in the survey results.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>