Fix an error introduced resolving conflicts with camnoc_virt node.

Fixes: 0c9dde0d ("arm64: dts: qcom: sm8150: Add secondary USB and PHY nodes")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20201124041003.3600-1-jonathan@marek.caSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

The uart2 node has been renamed, apply the change to sm8250-hdk dts too so
that serial output works.

Fixes: 91ed0e90 ("arm64: dts: qcom: add sm8250 hdk dts")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20201123143538.14198-1-jonathan@marek.caSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Commit 22337b91 ("arm64: dts: qcom: sc7180: Changed polling mode
in Thermal-zones node") sets both 'polling-delay' and
'polling-delay-passive' to zero with the rationale that TSENS interrupts
are enabled. A TSENS interrupt fires when the temperature of a thermal
zone reaches a trip point, which makes regular polling below the passive
trip point temperature unnecessary. However the situation is different
when passive cooling is active, regular polling is still needed to
trigger a periodic evaluation of the thermal zone by the thermal governor.

Change 'polling-delay-passive' back to the original value of 250 ms.
Commit 2315ae70 ("arm64: dts: qcom: sc7180: Add gpu cooling
support") recently changed the value for the GPU thermal zones from
zero to 100 ms, also set it to 250 ms for uniformity. If some zones
really need different values these can be changed in dedicated patches.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: 22337b91 ("arm64: dts: qcom: sc7180: Changed polling mode in Thermal-zones node")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20201111120334.1.Ifc04ea235c3c370e3b21ec3b4d5dead83cc403b4@changeidSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Some versions of the firmware leave i2c gpios in a wrong state.
Add pinctrl that disables pin bias since external pull-up resistors
are present.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Fixes: 1329c1ab ("arm64: dts: qcom: Add device tree for Samsung Galaxy A3U/A5U")
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-6-nikitos.tr@gmail.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

L8150 uses aw2013 LED contriller for notification LED on the front
of the device. Add it to the device tree
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-5-nikitos.tr@gmail.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

L8150 uses SGM3785 Flash LED driver. It is similar to SGM3140 but
can also be controlled with PWM. Since SoC doesn't have PWM, add
led to the device tree using sgm3140 driver.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-4-nikitos.tr@gmail.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

L8150 has:
 - BMC156 accelerometer and magnetic sensor
 - BMG160 gyroscope sensor
Add them to the device tree.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-3-nikitos.tr@gmail.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

L8150 has RMI4 compatible Synaptics touchscreen on
blsp_i2c5. It is powered by fixed regulator. Add
both to the device tree.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-2-nikitos.tr@gmail.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

L8150 has a vibrator connected to PM8916. Add it to the device tree.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-1-nikitos.tr@gmail.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This patch wires up touchscreen support on Samsung Galaxy A3 2015.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Link: https://lore.kernel.org/r/20201115195058.27097-1-michael.srba@seznam.czSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

There's a proximity sensor on Lazor devices, but only for LTE SKUs.
Enable it only on the Lazor LTE SKUs and also configure it properly so
it works.

Cc: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201120183825.547310-1-swboyd@chromium.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This interrupt has an external pull-up so we don't need to pull it up
again. Drop the internal pull here. Note I don't think this really
changes anything, just noticed while looking at this irq pin.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201120200913.618274-1-swboyd@chromium.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add fastrpc nodes for sDSP, cDSP, and aDSP.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200908131500.19891-1-jonathan@marek.caSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

RB5 makes use of the two USB controllers onboard. USB0 is connected
to the Type C port and USB1 is connected to USB3.1 HUB which exposes
following downstream ports:

* 2 Type A ports
* 2 HS/SS ports on the expansion connector
* USB to LAN device

Hence, enable these two controllers with the required PHYs.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200917082622.6823-4-manivannan.sadhasivam@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

RNG (Random Number Generator) in SM8250 features PRNG EE (Execution
Environment), hence add devicetree support for it.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200921065806.10928-1-manivannan.sadhasivam@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Qualcomm boards should define two compatible strings: one for board,
anoter one for SoC family. sm8250-mtp.dts lists just the board
compatible, which makes it incompatible with qcom.yaml schema.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 60378f1a ("arm64: dts: qcom: sm8250: Add sm8250 dts file")
Link: https://lore.kernel.org/r/20200930112133.2091505-1-dmitry.baryshkov@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Enable IOMMUs configuration for QUP nodes to stop SM8250 boards from
rebooting when using I2C DMA transfers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201010132125.416064-1-dmitry.baryshkov@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add support for uSD card on RB5 using the SDHC2 interface.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[DB: disabled 1.8V support to get SDHC to work]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201028190955.1264526-2-dmitry.baryshkov@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add support for SDC2 which can be used to interface uSD card.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[DB: minor fixes: clocks, iommus, opps]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201028190955.1264526-1-dmitry.baryshkov@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add initial HDK865 dts, based on sm8250-mtp, with a few changes.
Notably, regulator configs are changed a bit.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200609194030.17756-9-jonathan@marek.caSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add initial HDK855 dts, based on sm8150-mtp, with a few changes.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200609194030.17756-8-jonathan@marek.caSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add device nodes for the USB3 controller, QMP SS PHY and
SNPS HS PHY.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200609194030.17756-7-jonathan@marek.caSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add dts nodes for the secondary USB controller and related PHY nodes.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200609194030.17756-6-jonathan@marek.caSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add the apps_smmu node for sm8250.

For UFS, now that the kernel initializes the iommu, the stream mappings
set by the bootloader are cleared. Adding the iommus property is required
so that new mappings are created for UFS.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200609194030.17756-5-jonathan@marek.caSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add the apps_smmu node for sm8150.

For UFS, now that the kernel initializes the iommu, the stream mappings
set by the bootloader are cleared. Adding the iommus property is required
so that new mappings are created for UFS.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/20200609194030.17756-4-jonathan@marek.caSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add LLCC system cache controller entry for sm8150 to support sm8150
for LLCC.
Signed-off-by: Souradeep Chowdhury <schowdhu@codeaurora.org>
Link: https://lore.kernel.org/r/8f0e818485941076d62a8dc9f711b0fb868ba080.1601452132.git.schowdhu@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

After many years of struggle, commit fa2d0aa9 ("mmc: core: Allow
setting slot index via device tree alias") finally allows the use of
aliases to number SD/MMC slots.  Let's do that for sc7180 SoCs so that
if eMMC and SD are both used they have consistent numbers across boots
and kernel changes.

Picking numbers can be tricky.  Do we call these "1" and "2" to match
the name in documentation or "0" and "1" with the assertion that we
should always start at 0 and count up?

While the "start counting at 0" makes sense if there are not already
well-defined numbers for all sd/mmc controllers, in the case of sc7180
there _are_ well defined numbers.  IMO it is less confusing to use
those and match the docs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201111073652.1.Ia5bccd9eab7d74ea1ea9a7780e3cdbf662f5a464@changeidSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-10-vkoul@kernel.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-9-vkoul@kernel.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-8-vkoul@kernel.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-7-vkoul@kernel.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-6-vkoul@kernel.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-5-vkoul@kernel.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-4-vkoul@kernel.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-3-vkoul@kernel.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-2-vkoul@kernel.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add device tree support for Microsoft Lumia 950 XL smartphone.
It is based on the msm8994 chipset and is able to boot Linux
using a custom EDK2 implementation. EL2 core startup is possible
with spin-table, but for now, we'll stick with PSCI.

The board currently supports:
* Screen console via EFIFB
* SDHCI
* I2C
* UART
* PSCI core bringup
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20201005150313.149754-12-konradybcio@gmail.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This is a very basic dwc3 configuration (no PHYs yet),
but it works.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20201005150313.149754-11-konradybcio@gmail.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This is a very basic dwc3 configuration (no PHYs yet),
but it works.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20201005150313.149754-10-konradybcio@gmail.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This adds touchscreen capabilities to the Lumia 950.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20201005150313.149754-9-konradybcio@gmail.comSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>