Adds a new CONFIG_PPC_64K_PAGES which, when enabled, changes the kernel
base page size to 64K.  The resulting kernel still boots on any
hardware.  On current machines with 4K pages support only, the kernel
will maintain 16 "subpages" for each 64K page transparently.

Note that while real 64K capable HW has been tested, the current patch
will not enable it yet as such hardware is not released yet, and I'm
still verifying with the firmware architects the proper to get the
information from the newer hypervisors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

glibc expects to count lines beginning with "processor" to determine
the number of processors, not lines beginning with "Processor".  So,
give glibc the format it expects.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We don't want to call dump_cpu_info() from cpu_init() after boot since
it produces a lot of unnecessary noise - since cpu_init() gets called
on resume and hotplug cpu insertion events.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

// disagrees with ld's script parsing ability.  Don't use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Richard Purdie

Update the PXA pm.c file to allow machines (such as the Sharp
Zaurus) to override the standard pm functions but reuse/wrap them
where needed.

The init call is made slightly earlier to give machine code an init
level to override them in removing any race.

Signed-off-by: Richard Purdie
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

Since we know the value of cpsr on entry, we can replace the bic+orr with
a single eor.  Also remove a possible result delay (at least on XScale).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Make the uengine loader use ixp2000_reg_wrb in the right places.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Alessandro Zummo

  This patch fixes AHB/PCI endianness problems when the
 processor is in little-endian mode.

 The patch configures the CSR register closely following the directives
 in [1], paragraph 4.1, page 19.

 According to the considerations in [1], page 11, while the AHB bus
 supports both endian modes, on the IXP4XX it always uses big-endian.

 The PCI bus is connected to the South AHB. A wrong setting in the CSR
 register will thus cause a malfunctional PCI bus.

 A schematic diagram of the bus interconnections on the IXP4XX
 can be found in [1], page 18.

 The patch has been verified to work on the NSLU2 in
 both LE and BE modes.

 The author is Peter Korsgaard.

 [1] Intel® IXP4XX Product Line of Network Processors and IXC1100
 Control Plane Processor:
 Understanding Big Endian and Little Endian Modes

 http://www.intel.com/design/network/applnots/25423701.pdfSigned-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Dirk Opfer

This patch adds basic machine support for the Sharp SL-6000x (Tosa) PDAs.

Signed-off-by: Dirk Opfer
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The offsets of the registers are in a different place, and
some parts cannot handle a full set of modem control signals.
Signed-off-by: Pantelis Antoniou <pantelis@embeddedalley.ocm>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

my patch "x86: initialise tss->io_bitmap_owner to something" (commit ID
d5cd4aad) introduced a problem with a
program (DOSEMU) that called ioperm after already doing some port i/o.

The problem is that a process switch return causes tss->io_bitmap_base
to be set to IO_BITMAP_OFFSET so that the fault (that *really* sets the
io bitmap) never triggers.

This fixes that regression.
Signed-off-by: Bart Oldeman <bartoldeman@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Some visually impaired people use hardware devices which directly read
the vga screen. When newt for instance asks to hide the cursor for
better visual aspect, the kernel puts the vga cursor out of the screen,
so that the cursor position can't be read by the hardware device. This
is a great loss for such people.

Here is a patch which uses the same technique as CUR_NONE for hiding the
cursor while still moving it.

Mario, you should apply it to the speakup kernel for access floppies
asap. I'll submit a 2.4 patch too.

Signed-off-by: samuel.thibault@ens-lyon.org
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Statically allocated devices in module data is a potential cause
of oopsen.  The device may be in use by a userspace process, which
will keep a reference to the device.  If the module is unloaded,
the module data will be freed.  Subsequent use of the platform
device will cause a kernel oops.

Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>

Statically allocated devices in module data is a potential cause
of oopsen.  The device may be in use by a userspace process, which
will keep a reference to the device.  If the module is unloaded,
the module data will be freed.  Subsequent use of the platform
device will cause a kernel oops.

Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>

Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device.  If the module is unloaded, the module
text will be freed.  Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.

Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>

Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device.  If the module is unloaded, the module
text will be freed.  Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.

Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>

Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device.  If the module is unloaded, the module
text will be freed.  Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.

Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>

Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device.  If the module is unloaded, the module
text will be freed.  Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.

Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>

Re-jig the simple platform device support to allow private data
to be attached to a platform device, as well as allowing the
parent device to be set.

Example usage:

	pdev = platform_device_alloc("mydev", id);
	if (pdev) {
		err = platform_device_add_resources(pdev, &resources,
						    ARRAY_SIZE(resources));
		if (err == 0)
			err = platform_device_add_data(pdev, &platform_data,
						       sizeof(platform_data));
		if (err == 0)
			err = platform_device_add(pdev);
	} else {
		err = -ENOMEM;
	}
	if (err)
		platform_device_put(pdev);
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>

Adds a phy_mask field to struct mii_bus and uses it.  This field
indicates each phy address to be ignored when probing the mdio bus.

This support is needed for the fs_enet and ibm_emac drivers to be
converted to the generic phy layer among other drivers. Many systems
lock up on probing certain phy addresses or probing doesn't return
0xffff when nothing is found at the address. A new driver I'm
working on also makes use of this mask.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Some boards using the 79c976 pcnet32 chip will hang the system if the
ethtool --register-dump is performed with the device operational.  The
request to read bcr30 is retried by the PCI device infinitely without
returning data, hanging the system.

Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

This patch is a better fix for Allied Telesyn 2700/2701 FX boards than
the change made in early January this year.  It allows the user to
select the speed/duplex via module_param, but if no selection is made,
forces the speed to 100 FD.  It fixes both Bugzilla bugs 2669 and 4551.
Tested ia32 and ppc64 by myself, and by the originator of bug 2669.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Display the name eth%d or pci_name() of device which fails to allocate
memory.  When changing ring size via ethtool, it also releases the
lock before returning on error.  Added comment that the caller of
pcnet32_alloc_ring must call pcnet32_free_ring on error, to avoid leak.
Tested ia32 by forcing allocation errors.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Hi,
This patch provides updated documentation on the Neterion(S2io) driver.

Please review the patch.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Hi,
This patch  provides dynamic two buffer-mode and 3 buffer-mode options.
Previously 2 buffer-mode was compilation option. Now with this patch applied
one can load driver in 2 buffer-mode with module-load parameter

ie.
#insmod s2io.ko rx_ring_mode=2

This patch also provides 3 buffer-mode which provides header separation
functionality. In 3 buffer-mode skb->data will have L2/L3/L4 headers and
"skb_shinfo(skb)->frag_list->data" will have have L4 payload.
one can load driver in 3 buffer-mode with same above module-load parameter

ie.
#insmod s2io.ko rx_ring_mode=3

Please review the patch.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

fid is declared as a u32 (unsigned int), and then a few lines later, it is checked for a value < 0, which is clearly useless.
In the two locations this function is used, in one it is *explicitly* given a negative number, which would be ignored with the
current definition.

Thanks to LinuxICC (http://linuxicc.sf.net).
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Currently the driver takes a reference only for requests coming by way
of the gendisk, not for requests coming by way of the struct device or
struct scsi_device.  Such requests can arrive in the rescan, flush,
and shutdown pathways.

The patch also makes the scsi_disk keep a reference to the underlying
scsi_device, and it erases the scsi_device's pointer to the scsi_disk
when the scsi_device is removed (since the pointer should no longer be
used).

This resolves Bugzilla entry #5237.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The printks that aren't for debugging should use the name of the controller,
not the driver name. Multiple MMC controllers aren't that common today, but
this is the right way to do things.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

- egcs is not supported by kernel 2.6
- gcc 3.3 seems to be a good choice on ARM
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There is a broken if clause in the wbsd driver that can cause the
driver to try and configure the chip even though none is found. This
results in i/o on invalid ports.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>