Supporting both original SCA and SCA-II in one file was nice at some
point but now it's increasingly painful.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>

This patch updates the version number to 3.96.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the 57780 PHY ID to the broadcom module.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the 57780 ASIC revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ENABLE_APE flag tells the driver whether or not the device has an
Application Processing Engine (APE).  The APE does not need the PHY to
be powered unless it is running management firmware.  For backwards
compatibility, management firmware will still set the ENABLE_ASF bit.
Consequently, there is no reason to consider the ENABLE_APE flag when
deciding whether or not to power down the phy.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Per Dave Miller's suggestion, replace the remaining ioremap_nocache()
call with pci_ioremap_bar().  Remove the two IORESOURCE_MEM checks as
they are redundant.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch extracts the bootcode firmware version from the alternate
selfboot patch NVRAM format.  This format is used on the 5784, 5761 and
some newer devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

GPHY Autopowerdown (APD) is a way to save power when energy is not
detected on the wire.  At the moment, only the 5784 and 5761 are
capable of enabling this mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch disables CLKREQ at 10Mbps and 100Mbps to workaround a TX BD
corruption issue.  This problem only affects the 5784 and 5761 (and
57780 AX) ASIC revisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes sure the device is a PCIX device before attempting to
use the pcix_cap device structure member.  This is prep work for the
following patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch replaces hardcoded 2's with the NET_IP_ALIGN constant or
TG3_RAW_IP_ALIGN where appropriate.  Some platforms can redefine the
NET_IP_ALIGN definition to zero if unaligned DMA transfers cost more
than the IP header alignment gains.  This patch represents a
performance improvement when using the 5701 on these platforms.
The copy path can be avoided.

TG3_RAW_IP_ALIGN is used in cases where we always want to align the
IP header on dword boundaries.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove redundant argument comments in files of net/*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check return code for all NVM accesses[1] and error out accordingly; log
a debug message for failed accesses.

For ICH8/9, the valid NVM bank detect function was not checking whether the
SEC1VAL (sector 1 valid) bit in the EECD register was itself valid (bits 8
and 9 also have to be set).  If invalid, it would have defaulted to the
possibly invalid bank 0.  Instead, try to use the valid bank detection
method used by ICH10 which has been cleaned up a bit.

[1] - reads and updates only; not writes because those are only writing to
the Shadow RAM, the update following the write is the only thing actually
writing the modified Shadow RAM contents to the NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On 82571 with SerDes, the true link state is not always correct when read
from the STATUS register; use existing e1000_has_link() function instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than reading the NVM to get the EEPROM version number everytime the
ethool get_drvinfo function is called, read it once during probe and save
it for future reference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing newline from debug message.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sync flow control variables and usage model with that found in the ixgbe
driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On ESB2, the MAC-to-PHY (Kumeran) interface must be configured after link
is up before any traffic is sent; a new PHY operations function pointer is
provided for this.  To facilitate read/write of the Kumeran registers
without blocking PHY register writes, the driver/firmware synchronization
method which previously used a hardware semaphore for both PHY and Kumeran
register accesses is now split.  New Kumeran register read/write functions
utilize this new synchronization method.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check return of pci_save_state and error out accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some branding strings (displayed via lspci) are missing from the comments in
various family-specific files in the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check for link test does not work properly for 82571 parts in a blade
environment with an unterminated serdes link partner.  Make the test more
robust by checking the invalid bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow the convention used elsewhere in e1000e to 'commit' PHY changes
instead of directly writing to the PHY CTRL register to reset it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There has been an issue seen with the pci-e quad port adapters that will
cause them to generate a pci-e correctable error on some system while
transitioning to D3.

Since no action is needed on this correctable error the simplest solution
is to mask off the reporting of correctable errors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

They are no longer a rwlocks.
Signed-off-by: David S. Miller <davem@davemloft.net>

When compile test my previous patch, I found PC300 driver was broken.
And there is no explanation about the broken.
Add the reason about why change this driver to broken in Kconfig.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev's private data should be hdlc.
pc300dev_t is the private data of hdlc.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For killing directly reference of netdev->priv, use netdev->ml_priv to replace it.
Because the private pvc data comes from add_pvc() and can't be allocated in
alloc_netdev().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can avoid some useless instructions if !CONFIG_NET_NS

Because of RCU, we use INET_MATCH or INET_TW_MATCH twice for the found
socket, so thats six instructions less per incoming TCP packet.

Yet another tbench speedup :)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds #include <linux/timer.h> in lib80211.h to avoid
these compilation erros.

> In file included from /work/src/wireless-testing/net/wireless/lib80211.c:24:
> /work/src/wireless-testing/include/net/lib80211.h:113: error: field
> 'crypt_deinit_timer' has incomplete type
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_info_init':
> /work/src/wireless-testing/net/wireless/lib80211.c:83: error: implicit
> declaration of function 'setup_timer'
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_info_free':
> /work/src/wireless-testing/net/wireless/lib80211.c:95: error: implicit
> declaration of function 'del_timer_sync'
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_deinit_handler':
> /work/src/wireless-testing/net/wireless/lib80211.c:157: error:
> implicit declaration of function 'add_timer'
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_delayed_deinit':
> /work/src/wireless-testing/net/wireless/lib80211.c:182: error:
> implicit declaration of function 'timer_pending'
> make[3]: *** [net/wireless/lib80211.o] Error 1
> make[2]: *** [net/wireless] Error 2
> make[1]: *** [net] Error 2
> make: *** [sub-make] Error 2
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Modify the file comments to reflect the current maintainers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As noted by John Linville, the RTL818X maintainers have "moved on", and the
responsibilities for RTL8180 and RTL8187 have been split. This is the
corresponding update of MAINTAINERS.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove converting the MAC address to a string by a direct byte
conversion and use %pM instead, since the code is now boilerplate
use a macro to define the show functions, and also use the shorter
__ATTR_RO macro to define the attributes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Michael and Andrea have moved-on, so we shouldn't be bothering them
about these drivers anymore.

Actually, Herton Ronaldo Krzesinski, Hin-Tak Leung, and Larry Finger
have been handling the rtl8187 stuff for a while.  So, I would welcome a
patch from one of them changing this to just RTL8180 and adding an
RTL8187 entry with their names...
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This updates rtl8180 handling for short slot after "mac80211: fix short
slot handling". Only rtl8180_rtl8225 actually had code for handling
short slot times, so the other RF devices are untouched by this change.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Otherwise, the BUILD_BUG_ON calls in ieee80211_tx_info_clear_status can
fail on some architectures.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The old ieee80211 code only remains as a support library for the ipw2100
and ipw2200 drivers.  So, move the code and rename it appropriately to
reflects it's true purpose and status.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>