Add handling of missed events in omap_dss_pm_notif which are
needed to support hibernation (suspend to disk).
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The doc refers to Documentation/devicetree/bindings/video/video-ports.txt
which does not exist. The documentation seems to be outdated and wants to
refer to Documentation/devicetree/bindings/graph.txt instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We don't need VT switch when suspending/resuming, so disable it. This
speeds up suspend/resume.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: NeilBrown <neil@brown.name>

If sh_mobile_lcdc_probe() fails after the allocation of driver-private
data, but before the initialization of all channels, a warning will be
printed due to the destruction of an uninitialized mutex:

    WARNING: CPU: 0 PID: 1 at kernel/locking/mutex-debug.c:116 mutex_destroy+0x5c/0x7c()
    DEBUG_LOCKS_WARN_ON(mutex_is_locked(lock))
    ...
    Backtrace:
    ...
    [<c00425b4>] (mutex_destroy) from [<c01d5858>] (sh_mobile_lcdc_remove+0x1bc/0x230)
     r4:df6a4800 r3:00000000
    [<c01d569c>] (sh_mobile_lcdc_remove) from [<c01d6620>] (sh_mobile_lcdc_probe+0xd54/0xe28)

Move the initialization of the mutexes from sh_mobile_lcdc_channel_init()
to immediately after the allocation of driver-private data to fix this.

Note that the interrupt number is moved to a new variable "irq", so we
can reuse the existing variable "i" for iterating over the channels.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The ROP3 attribute is expressed as an integer in the 0-255 range. Remove
the wrong conversion to boolean when parsing it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This if statement should be pushed out one tab to line up with the rest.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The return type of wait_for_completion_timeout is unsigned long not
int. This patch fixes up the declarations only.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This is only an API consolidation and should make things more readable by
replacing  var * HZ / 1000  by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

this patch fixes following sparse warning:

via_clock.c:33:12: warning: symbol 'via_slap' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Make of_device_id array const.
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

we should really be using memset_io() instead of using memset() as
this is actually io space mapped into our memory.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

It was found that having two displays enabled and having an NV12 overlay
on one of the displays will cause underflows/synclosts. Debugging this
pointed to some issue with MFLAG.

It is unclear why this issue is happening, but it looks like there is a
HW bug related to MFLAG and FIFO management. Disabling MFLAG makes this
issue go away, but then we lose the benefit of MFLAG. Also forcing MFLAG
always on makes the issue go away.

Also, using certain values for MFLAG_START, MFLAG thresholds and PRELOAD
makes the issue go away, but there was no obvious logic to which values
work and which don't.

As a workaround until more information about this is found, force MFLAG
always on to make NV12 usable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

OMAP5 has support for MFLAG feature, which allows DSS to dynamically
increase the priority of DISPC's DMA traffic. At the moment we don't
have support for it.

It was noticed that on DRA7 with high bandwidth use cases we see FIFO
underflows. Implementing MFLAG support removed those underflows.
Interestingly, on OMAP5 uEVM no such overflows were seen.

This patch adds a simple MFLAG implementation, where we use a fixed
MFLAG threshold value based on the FIFO size. The thresholds are set to
4/8 of fifo size for low threshold, and 5/8 of fifo size for high
threshold.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

At the moment we don't setup FIFO thresholds by default in omapdss. It's
supposed to be done by the user of omapdss. And that is missing from
omapdrm, causing unoptimal thresholds to be used when using omapdrm.

While I believe it's in theory better to allow the user of omapdss to
setup the fifo thresholds, in practice we always use the same values,
and we could as well setup the thresholds in omapdss.

Furthermore, in omapdss init we always swap the FIFO used for GFX and WB
overlays, but we don't swap the FIFO thresholds for those overlays
(which is the reason for omapdrm using unoptimal HW reset values). So
it would make sense to setup the thresholds to account for the swapping
of the FIFOs.

So, this patch adds code to setup default FIFO tresholds at omapdss
init.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Dispc driver presumes that the callers handle locking for all normal
functions. However, omapdrm doesn't handle this, and presumes that all
overlay manager registers are private to that overlay manager, and thus
presumes that configurations for overlay managers can be written via
different threads freely.

For many registers the above is true. The exceptions are DISPC_CONTROL
and DISPC_CONFIG registers, which contain bits for both LCD and TV
overlay managers.

Fixing this properly in omapdrm means a big omapdrm rewrite. So, for
now, add locking to dispc for the problematic registers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Somnath Mukherjee <somnath@ti.com>

omapdrm doesn't always configure the overlays correctly, causing the
overlay setup functions to be called with zero timings. This leads to
division by zero error.

This happens, for example, when a HDMI cable is not connected, but a
user tries to setup a plane with scaling.

Fixing omapdrm is a big job, so for now let's check for the bad timings
in DISPC and return an error.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The common 'struct videomode' does not have a flag to select when the
sync signals should be driven.

The default behavior of DISPC HW is to drive the sync signal on the
opposite pixel clock edge from data signal, which is also what the
videomode_to_omap_video_timings() uses.

However, it looks like what panels usually expect is that the data and
sync signals are driven on the same edge, so let's change
videomode_to_omap_video_timings() to set the sync_pclk_edge accordingly.

Note that this only affect panels drivers that use
videomode_to_omap_video_timings(), probably when getting the video
timings directly from DT data. The drivers can still configure the
sync_pclk_edge independently if they so wish.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

At the moment the enum values for ACTIVE_HIGH and RISING_EDGE are 0, and
ACTIVE_LOW and FALLING_EDGE are 1, to match the values programmed to HW.
The previous patch removed this dependency.

Swap the enum values the other way around. This doesn't change the
behavior in any way, but makes it easier to debug as value of '1' means
HIGH or RISING.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

When configuring the lcd timings, instead of writing enum values
directly to the HW, use switch-case to get the value to be programmed.

This is safer and also allows us to change the enum values.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

DISPC can drive data lines either on rising or falling pixel clock edge,
which can be configured by the user.

Sync lines can also be driven on rising or falling pixel clock edge, but
additionally the HW can be configured to drive the sync lines on
opposite clock edge from the data lines.

This opposite edge setting does not make any sense, as the same effect
can be achieved by just setting the sync lines to be driven on the other
edge compared to the data lines. It feels like some kind of backward
compatibility option, even if all DSS versions seem to have the same
implementation.

To simplify the code and configuration of the signals, and to make the
dispc timings more compatible with what is used on other platforms,
let's just remove the whole opposite-edge support.

The drivers that used OMAPDSS_DRIVE_SIG_OPPOSITE_EDGES setting are
changed so that they use the opposite setting from the data edge.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

TFP410 requires that DE is active high and the data and syncs are driven
on rising pixel clock edge. However, at the moment the driver doesn't
request such syncs, and the end result is that the sync settings depend
on default values, which are not right in all cases.

Set the sync values explicitly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The DISPC driver checks that the buffer address is not 0. However, when
using TILER, the address space is TILER specific and 0 is a valid
address.

Fix the check to allow address of 0 for TILER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: srinivas pulukuru <srinivas.pulukuru@ti.com>

It has been observed that the current SDA-HOLD time is too short for
some board/cable/monitor combinations. Increase the SDA-HOLD time to
1000ns.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

AM43xx supports pixel clock divider of 1, just like all OMAP3+ SoCs. Fix
the minimum divider value.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

.. after extensive statistical analysis of my G+ polling, I've come to
the inescapable conclusion that internet polls are bad.

Big surprise.

But "Hurr durr I'ma sheep" trounced "I like online polls" by a 62-to-38%
margin, in a poll that people weren't even supposed to participate in.
Who can argue with solid numbers like that? 5,796 votes from people who
can't even follow the most basic directions?

In contrast, "v4.0" beat out "v3.20" by a slimmer margin of 56-to-44%,
but with a total of 29,110 votes right now.

Now, arguably, that vote spread is only about 3,200 votes, which is less
than the almost six thousand votes that the "please ignore" poll got, so
it could be considered noise.

But hey, I asked, so I'll honor the votes.

Pull ext4 fixes from Ted Ts'o:
 "Ext4 bug fixes.

  We also reserved code points for encryption and read-only images (for
  which the implementation is mostly just the reserved code point for a
  read-only feature :-)"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix indirect punch hole corruption
  ext4: ignore journal checksum on remount; don't fail
  ext4: remove duplicate remount check for JOURNAL_CHECKSUM change
  ext4: fix mmap data corruption in nodelalloc mode when blocksize < pagesize
  ext4: support read-only images
  ext4: change to use setup_timer() instead of init_timer()
  ext4: reserve codepoints used by the ext4 encryption feature
  jbd2: complain about descriptor block checksum errors

Pull more vfs updates from Al Viro:
 "Assorted stuff from this cycle.  The big ones here are multilayer
  overlayfs from Miklos and beginning of sorting ->d_inode accesses out
  from David"

* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (51 commits)
  autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
  procfs: fix race between symlink removals and traversals
  debugfs: leave freeing a symlink body until inode eviction
  Documentation/filesystems/Locking: ->get_sb() is long gone
  trylock_super(): replacement for grab_super_passive()
  fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
  Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
  VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry)
  SELinux: Use d_is_positive() rather than testing dentry->d_inode
  Smack: Use d_is_positive() rather than testing dentry->d_inode
  TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR()
  Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode
  Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb
  VFS: Split DCACHE_FILE_TYPE into regular and special types
  VFS: Add a fallthrough flag for marking virtual dentries
  VFS: Add a whiteout dentry type
  VFS: Introduce inode-getting helpers for layered/unioned fs environments
  Infiniband: Fix potential NULL d_inode dereference
  posix_acl: fix reference leaks in posix_acl_create
  autofs4: Wrong format for printing dentry
  ...

Pull ARM fix from Russell King:
 "Just one fix this time around.  __iommu_alloc_buffer() can cause a
  BUG() if dma_alloc_coherent() is called with either __GFP_DMA32 or
  __GFP_HIGHMEM set.  The patch from Alexandre addresses this"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8305/1: DMA: Fix kzalloc flags in __iommu_alloc_buffer()

X-Coverup: just ask spender
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

use_pde()/unuse_pde() in ->follow_link()/->put_link() resp.

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

As it is, we have debugfs_remove() racing with symlink traversals.
Supply ->evict_inode() and do freeing there - inode will remain
pinned until we are done with the symlink body.

And rip the idiocy with checking if dentry is positive right after
we'd verified debugfs_positive(), which is a stronger check...

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

I've noticed significant locking contention in memory reclaimer around
sb_lock inside grab_super_passive(). Grab_super_passive() is called from
two places: in icache/dcache shrinkers (function super_cache_scan) and
from writeback (function __writeback_inodes_wb). Both are required for
progress in memory allocator.

Grab_super_passive() acquires sb_lock to increment sb->s_count and check
sb->s_instances. It seems sb->s_umount locked for read is enough here:
super-block deactivation always runs under sb->s_umount locked for write.
Protecting super-block itself isn't a problem: in super_cache_scan() sb
is protected by shrinker_rwsem: it cannot be freed if its slab shrinkers
are still active. Inside writeback super-block comes from inode from bdi
writeback list under wb->list_lock.

This patch removes locking sb_lock and checks s_instances under s_umount:
generic_shutdown_super() unlinks it under sb->s_umount locked for write.
New variant is called trylock_super() and since it only locks semaphore,
callers must call up_read(&sb->s_umount) instead of drop_super(sb) when
they're done.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Fanotify probably doesn't want to watch autodirs so make it use d_can_lookup()
rather than d_is_dir() when checking a dir watch and give an error on fake
directories.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Fix up the following scripted S_ISDIR/S_ISREG/S_ISLNK conversions (or lack
thereof) in cachefiles:

 (1) Cachefiles mostly wants to use d_can_lookup() rather than d_is_dir() as
     it doesn't want to deal with automounts in its cache.

 (2) Coccinelle didn't find S_IS* expressions in ASSERT() statements in
     cachefiles.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Convert the following where appropriate:

 (1) S_ISLNK(dentry->d_inode) to d_is_symlink(dentry).

 (2) S_ISREG(dentry->d_inode) to d_is_reg(dentry).

 (3) S_ISDIR(dentry->d_inode) to d_is_dir(dentry).  This is actually more
     complicated than it appears as some calls should be converted to
     d_can_lookup() instead.  The difference is whether the directory in
     question is a real dir with a ->lookup op or whether it's a fake dir with
     a ->d_automount op.

In some circumstances, we can subsume checks for dentry->d_inode not being
NULL into this, provided we the code isn't in a filesystem that expects
d_inode to be NULL if the dirent really *is* negative (ie. if we're going to
use d_inode() rather than d_backing_inode() to get the inode pointer).

Note that the dentry type field may be set to something other than
DCACHE_MISS_TYPE when d_inode is NULL in the case of unionmount, where the VFS
manages the fall-through from a negative dentry to a lower layer.  In such a
case, the dentry type of the negative union dentry is set to the same as the
type of the lower dentry.

However, if you know d_inode is not NULL at the call site, then you can use
the d_is_xxx() functions even in a filesystem.

There is one further complication: a 0,0 chardev dentry may be labelled
DCACHE_WHITEOUT_TYPE rather than DCACHE_SPECIAL_TYPE.  Strictly, this was
intended for special directory entry types that don't have attached inodes.

The following perl+coccinelle script was used:

use strict;

my @callers;
open($fd, 'git grep -l \'S_IS[A-Z].*->d_inode\' |') ||
    die "Can't grep for S_ISDIR and co. callers";
@callers = <$fd>;
close($fd);
unless (@callers) {
    print "No matches\n";
    exit(0);
}

my @cocci = (
    '@@',
    'expression E;',
    '@@',
    '',
    '- S_ISLNK(E->d_inode->i_mode)',
    '+ d_is_symlink(E)',
    '',
    '@@',
    'expression E;',
    '@@',
    '',
    '- S_ISDIR(E->d_inode->i_mode)',
    '+ d_is_dir(E)',
    '',
    '@@',
    'expression E;',
    '@@',
    '',
    '- S_ISREG(E->d_inode->i_mode)',
    '+ d_is_reg(E)' );

my $coccifile = "tmp.sp.cocci";
open($fd, ">$coccifile") || die $coccifile;
print($fd "$_\n") || die $coccifile foreach (@cocci);
close($fd);

foreach my $file (@callers) {
    chomp $file;
    print "Processing ", $file, "\n";
    system("spatch", "--sp-file", $coccifile, $file, "--in-place", "--no-show-diff") == 0 ||
	die "spatch failed";
}

[AV: overlayfs parts skipped]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Use d_is_positive() rather than testing dentry->d_inode in SELinux to get rid
of direct references to d_inode outside of the VFS.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Use d_is_positive() rather than testing dentry->d_inode in Smack to get rid of
direct references to d_inode outside of the VFS.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Use d_is_dir() rather than d_inode and S_ISDIR().  Note that this will include
fake directories such as automount triggers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>