Commit d40f0b6f instroduced last_cs_enable to avoid setting
chipselect if it's not necessary, but it also introduces a bug. The
chipselect may not be set correctly on multi-device SPI busses. The
reason is that we can't judge the chipselect by bool last_cs_enable,
since chipselect may be modified after other devices were accessed.

So we should record the specific state of chipselect in case of
confusion.
Signed-off-by: Yun Zhou <yun.zhou@windriver.com>
Link: https://lore.kernel.org/r/20220217141234.72737-1-yun.zhou@windriver.comSigned-off-by: Mark Brown <broonie@kernel.org>

Now when there are no dynamical changes required, we may
constify struct pxa_spi_info variables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220225172350.69797-11-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Instead of using temporary storage, assign the values directly
to the corresponding struct pxa2xx_spi_controller members.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220225172350.69797-10-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Extract pxa2xx_spi_pci_clk_register() from ->probe() in order to reuse it
later on for getting rid of max_clk_rate temporary storage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220225172350.69797-9-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

All of the LPSS devices are using DMA and set the parameters up,
hence no need to test for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220225172350.69797-8-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Instead of creating an abstraction on top of PCI IDs, just use them directly.
The corresponding enum can be dropped.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220225172350.69797-7-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Move max_clk_rate to the corresponding ->setup() function to unify
with the rest.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220225172350.69797-6-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Instead of using conditional, move dma_burst_size to the corresponding
->setup() function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220225172350.69797-5-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Instead of using conditional, move port_id to the corresponding
->setup() functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220225172350.69797-4-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Since all platforms are using ->setup() function, drop unneeded check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220225172350.69797-3-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Refactor Quark X1000 handling code to use ->setup() instead of using
the configuration data structure directly.

It will allow to refactor further to avoid intermediate storage for
the used configuration parameters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220225172350.69797-2-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Refactor CE4100 handling code to use ->setup() instead of spreading
potentially confusing conditional.

Besides that, it will allow to refactor further to avoid intermediate
storage for the used configuration parameters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220225172350.69797-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

fix issue
/builds/robherring/linux-dt/Documentation/devicetree/bindings/spi/spi-sunplus-sp7021.example.dt.yaml:
spi@9C002D80: 'clocks-names' is a required property
From schema: /builds/robherring/linux-dt/Documentation/devicetree/bindings/spi/spi-sunplus-sp7021.yaml
delete unused required(clock-name)

Fixes: 3b8ab4da ("spi: Fix test error for sp7021")
Reported-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Li-hao Kuo <lhjeff911@gmail.com>
Link: https://lore.kernel.org/r/097bbc8b703b17e8fb3e3f6f6d2f97fe668bd5c5.1645770648.git.lhjeff911@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Krishna Yarlagadda <kyarlagadda@nvidia.com>:

Add ACPI support for Tegra210 QUAD SPI driver and a new compatilbe.

Add support for Tegra234 and soc data to select capabilities.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/20220222175611.58051-4-kyarlagadda@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add compatible string for Tegra234 for Tegra QUAD SPI
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/20220222175611.58051-3-kyarlagadda@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use device_reset api to replace duplicate code in driver to call
reset_control_get api with reset handle.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/20220222175611.58051-2-kyarlagadda@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().

Fixes: 743485ea ("spi: pxa2xx-pci: Do a specific setup in a separate function")
Fixes: 25014521 ("spi: pxa2xx-pci: Enable DMA for Intel Merrifield")
Reported-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223191637.31147-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

In order to make the underneath API easier to change in the future,
prevent users from dereferencing fwnode from struct device.
Instead, use the specific dev_fwnode() API for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223191948.31325-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

pci_get_slot() increases its reference count, the caller must
decrement the reference count by calling pci_dev_put()
Signed-off-by: Wang Qing <wangqing@vivo.com>
Link: https://lore.kernel.org/r/1644890407-65167-1-git-send-email-wangqing@vivo.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support for slave DT property spi-lsb-first, i.e., SPI_LSB_FIRST mode.
Duplicate the inline helpers bitbang_txrx_be_cpha{0,1} as LE versions.
Conditionally call them from all the spi-gpio txrx_word callbacks.

Some alternatives to this implementation approach were discussed back
then [0], but eventually it was considered reasonable.

[0] https://lore.kernel.org/linux-arm-kernel/20191212033952.5967-8-afaerber@suse.de/Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/feac3377-4ad1-77d8-9a18-3588d80fb909@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

STM32F4_SPI_SR_RXNE and STM32F4_SPI_SR_OVR are distinct bits in the same
status register.  ~STM32F4_SPI_SR_OVR | STM32F4_SPI_SR_RXNE is thus
equal to ~STM32F4_SPI_SR_OVR.

The original intention was likely for transmission-only transfers to
ignore interrupts both for when the Rx queue has bytes (RXNE) as well
as when these bytes haven't been read in time (OVR).

Fix the typo by adding the missing parenthesis.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20220201115142.3999860-1-a.fatoum@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Miquel Raynal <miquel.raynal@bootlin.com>:

DT bindings for stacked and parallel flash/memory devices.

base-commit: e783362e

Use of_device_get_match_data() to simplify the code.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220221020233.1925154-1-chi.minghao@zte.com.cnSigned-off-by: Mark Brown <broonie@kernel.org>

Provide an example of how to describe two flashes in eg. stacked mode.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220126112608.955728-4-miquel.raynal@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Describe two new memories modes:
- A stacked mode when the bus is common but the address space extended
  with an additinals wires.
- A parallel mode with parallel busses accessing parallel flashes where
  the data is spread.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220126112608.955728-3-miquel.raynal@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

The Xilinx QSPI controller has two advanced modes which allow the
controller to behave differently and consider two flashes as one single
storage.

One of these two modes is quite complex to support from a binding point
of view and is the dual parallel memories. In this mode, each byte of
data is stored in both devices: the even bits in one, the odd bits in
the other. The split is automatically handled by the QSPI controller and
is transparent for the user.

The other mode is simpler to support, it is called dual stacked
memories. The controller shares the same SPI bus but each of the devices
contain half of the data. Once in this mode, the controller does not
follow CS requests but instead internally wires the two CS levels with
the value of the most significant address bit.

Supporting these two modes will involve core changes which include the
possibility of providing two CS for a single SPI device
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220126112608.955728-2-miquel.raynal@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use dedicated function sysfs_emit() that does some extra checking,
e.g. to ensure that no more than PAGESIZE bytes are written.
In addition add a trailing newline to the output, that makes it
better readable from the console.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/56e1588d-d53b-73e9-fdc8-7fe30bf91f11@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Eliminate the follow smatch warning:
drivers/spi/spi-sunplus-sp7021.c:379 sp7021_spi_slave_transfer_one()
warn: inconsistent indenting
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220217010024.111904-1-yang.lee@linux.alibaba.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Jon Lin <jon.lin@rock-chips.com>:

A collection of fixes and support for new features in the Rockchip
driver.

base-commit: 80808768

The interrupt status bit of the previous error data transmition will
affect the next operation and cause continuous SPI transmission failure.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-7-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

the wakeup interrupt handler which is guaranteed not to run while
@resume noirq() is being executed. the patch can help to avoid the
wakeup source try to access spi when the spi is in suspend mode.
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-6-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

After power up, the cs and clock is in default status, and the cs-high
and clock polarity dts property configuration will take no effect until
the calling of rockchip_spi_config in the first transmission.
So preset them to make sure a correct voltage before the first
transmission coming.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-5-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

The spi which's version is higher than ver 2 will automatically
enable this feature.

If the length of master transmission is uncertain, the RK spi slave
is better to automatically stop after cs inactive instead of waiting
for xfer_completion forever.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-4-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

After slave abort, all DMA should be stopped, or it will affect the
next transmission and maybe abort again.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-3-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

Get num-cs u32 from dts of_node property rather than u16.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-2-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support for LPSS SPI on Intel Raptor Lake PCH-S. It has four
controllers each having two chip selects.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20220216091317.1302254-1-jarkko.nikula@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 20904355 ("spi: amd: Add support for version AMDI0062")
removed the cast ACPI_PTR() for no good reason. This wrapper is
important to make sure that the driver can be compiled with or without
CONFIG_ACPI enabled, useful for compiling test. Give back the cast so
compilation works again.

Fixes: 20904355 ("spi: amd: Add support for version AMDI0062")
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Link: https://lore.kernel.org/r/20220216162719.116062-1-andrealmeid@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

Intel Ice Lake-N has the same SPI serial flash controller as Ice Lake-LP.
Add Ice Lake-N PCI ID to the driver list of supported devices.

The device can be found on MacBookPro16,2 [1].

[1]: https://linux-hardware.org/?probe=f1c5cf0c43Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220215135139.4328-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from André Almeida <andrealmeid@collabora.com>:

This series do some cleanup and add support for new controller version,
AMDI0062.