In case ftmac100 is used with a DSA switch, Linux wants to set MTU
to 1504 to accommodate for DSA overhead. With the default max_mtu
it leads to the error message:
 ftmac100 92000000.mac eth0: error -22 setting MTU to 1504 to include DSA overhead

ftmac100 supports packet length 1518 (MAX_PKT_SIZE constant), so it is
safe to report it in max_mtu.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220821160844.474277-1-saproj@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Vladimir Oltean says:

====================
DSA changes for multiple CPU ports (part 3)

Those who have been following part 1:
https://patchwork.kernel.org/project/netdevbpf/cover/20220511095020.562461-1-vladimir.oltean@nxp.com/
and part 2:
https://patchwork.kernel.org/project/netdevbpf/cover/20220521213743.2735445-1-vladimir.oltean@nxp.com/
will know that I am trying to enable the second internal port pair from
the NXP LS1028A Felix switch for DSA-tagged traffic via "ocelot-8021q".
This series represents part 3 of that effort.

Covered here are some preparations in DSA for handling multiple DSA
masters:
- when changing the tagging protocol via sysfs
- when the masters go down
as well as preparation for monitoring the upper devices of a DSA master
(to support DSA masters under a LAG).

There are also 2 small preparations for the ocelot driver, for the case
where multiple tag_8021q CPU ports are used in a LAG. Both those changes
have to do with PGID forwarding domains.

Compared to v1, the patches were trimmed down to just another
preparation stage, and the UAPI changes were pushed further out to part 4.
https://patchwork.kernel.org/project/netdevbpf/cover/20220523104256.3556016-1-olteanv@gmail.com/

Compared to v2, I had to export a symbol I forgot to
(ocelot_port_teardown_dsa_8021q_cpu), to avoid a build breakage when the
felix and seville drivers are built as modules.
====================

Link: https://lore.kernel.org/r/20220819174820.3585002-1-vladimir.oltean@nxp.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Currently when we have 2 CPU ports configured for DSA tag_8021q mode and
we put them in a LAG, a PGID dump looks like this:

PGID_SRC[0] = ports 4,
PGID_SRC[1] = ports 4,
PGID_SRC[2] = ports 4,
PGID_SRC[3] = ports 4,
PGID_SRC[4] = ports 0, 1, 2, 3, 4, 5,
PGID_SRC[5] = no ports

(ports 0-3 are user ports, ports 4 and 5 are CPU ports)

There are 2 problems with the configuration above:

- user ports should enable forwarding towards both CPU ports, not just 4,
  and the aggregation PGIDs should prune one CPU port or the other from
  the destination port mask, based on a hash computed from packet headers.

- CPU ports should not be allowed to forward towards themselves and also
  not towards other ports in the same LAG as themselves

The first problem requires fixing up the PGID_SRC of user ports, when
ocelot_port_assigned_dsa_8021q_cpu_mask() is called. We need to say that
when a user port is assigned to a tag_8021q CPU port and that port is in
a LAG, it should forward towards all ports in that LAG.

The second problem requires fixing up the PGID_SRC of port 4, to remove
ports 4 and 5 (in a LAG) from the allowed destinations.

After this change, the PGID source masks look as follows:

PGID_SRC[0] = ports 4, 5,
PGID_SRC[1] = ports 4, 5,
PGID_SRC[2] = ports 4, 5,
PGID_SRC[3] = ports 4, 5,
PGID_SRC[4] = ports 0, 1, 2, 3,
PGID_SRC[5] = no ports

Note that PGID_SRC[5] still looks weird (it should say "0, 1, 2, 3" just
like PGID_SRC[4] does), but I've tested forwarding through this CPU port
and it doesn't seem like anything is affected (it appears that PGID_SRC[4]
is being looked up on forwarding from the CPU, since both ports 4 and 5
have logical port ID 4). The reason why it looks weird is because
we've never called ocelot_port_assign_dsa_8021q_cpu() for any user port
towards port 5 (all user ports are assigned to port 4 which is in a LAG
with 5).

Since things aren't broken, I'm willing to leave it like that for now
and just document the oddity.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This is a partial revert of commit c295f983 ("net: mscc: ocelot:
switch from {,un}set to {,un}assign for tag_8021q CPU ports"), because
as it turns out, this isn't how tag_8021q CPU ports under a LAG are
supposed to work.

Under that scenario, all user ports are "assigned" to the single
tag_8021q CPU port represented by the logical port corresponding to the
bonding interface. So one CPU port in a LAG would have is_dsa_8021q_cpu
set to true (the one whose physical port ID is equal to the logical port
ID), and the other one to false.

In turn, this makes 2 undesirable things happen:

(1) PGID_CPU contains only the first physical CPU port, rather than both
(2) only the first CPU port will be added to the private VLANs used by
    ocelot for VLAN-unaware bridging

To make the driver behave in the same way for both bonded CPU ports, we
need to bring back the old concept of setting up a port as a tag_8021q
CPU port, and this is what deals with VLAN membership and PGID_CPU
updating. But we also need the CPU port "assignment" (the user to CPU
port affinity), and this is what updates the PGID_SRC forwarding rules.

All DSA CPU ports are statically configured for tag_8021q mode when the
tagging protocol is changed to ocelot-8021q. User ports are "assigned"
to one CPU port or the other dynamically (this will be handled by a
future change).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

More logic will be added to dsa_tree_setup_master() and
dsa_tree_teardown_master() in upcoming changes.

Reduce the indentation by one level in these functions by introducing
and using a dedicated iterator for CPU ports of a tree.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The fact that the tagging protocol is set and queried from the
/sys/class/net/<dsa-master>/dsa/tagging file is a bit of a quirk from
the single CPU port days which isn't aging very well now that DSA can
have more than a single CPU port. This is because the tagging protocol
is a switch property, yet in the presence of multiple CPU ports it can
be queried and set from multiple sysfs files, all of which are handled
by the same implementation.

The current logic ensures that the net device whose sysfs file we're
changing the tagging protocol through must be down. That net device is
the DSA master, and this is fine for single DSA master / CPU port setups.

But exactly because the tagging protocol is per switch [ tree, in fact ]
and not per DSA master, this isn't fine any longer with multiple CPU
ports, and we must iterate through the tree and find all DSA masters,
and make sure that all of them are down.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This is an adaptation of commit c0a8a9c2 ("net: dsa: automatically
bring user ports down when master goes down") for multiple DSA masters.
When a DSA master goes down, only the user ports under its control
should go down too, the others can still send/receive traffic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

All the traffic to/from a DSA master is supposed to be distributed among
its DSA switch upper interfaces, so we should not allow other upper
device kinds.

An exception to this is DSA_TAG_PROTO_NONE (switches with no DSA tags),
and in that case it is actually expected to create e.g. VLAN interfaces
on the master. But for those, netdev_uses_dsa(master) returns false, so
the restriction doesn't apply.

The motivation for this change is to allow LAG interfaces of DSA masters
to be DSA masters themselves. We want to restrict the user's degrees of
freedom by 1: the LAG should already have all DSA masters as lowers, and
while lower ports of the LAG can be removed, none can be added after the
fact.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

When DSA gains support for multiple CPU ports in a LAG, it will become
mandatory to monitor the changeupper events for the DSA master.

In fact, there are already some restrictions to be imposed in that area,
namely that a DSA master cannot be a bridge port except in some special
circumstances.

Centralize the restrictions at the level of the DSA layer as a
preliminary step.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

dsa_slave_prechangeupper_sanity_check() is supposed to enforce some
adjacency restrictions, and calls ds->ops->port_prechangeupper if the
driver implements it.

We convert the error code from the port_prechangeupper() call to a
notifier code, and 0 is converted to NOTIFY_OK, but the caller of
dsa_slave_prechangeupper_sanity_check() stops at any notifier code
different from NOTIFY_DONE.

Avoid this by converting back the notifier code to an error code, so
that both NOTIFY_OK and NOTIFY_DONE will be seen as 0. This allows more
parallel sanity check functions to be added.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Traditionally, DSA has had a single netdev notifier handling function
for each device type.

For the sake of code cleanliness, we would like to introduce more
handling functions which do one thing, but the conditions for entering
these functions start to overlap. Example: a handling function which
tracks whether any bridges contain both DSA and non-DSA interfaces.
Either this is placed before dsa_slave_changeupper(), case in which it
will prevent that function from executing, or we place it after
dsa_slave_changeupper(), case in which we will prevent it from
executing. The other alternative is to ignore errors from the new
handling function (not ideal).

To support this usage, we need to change the pattern. In the new model,
we enter all notifier handling sub-functions, and exit with NOTIFY_DONE
if there is nothing to do. This allows the sub-functions to be
relatively free-form and independent from each other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Arseniy Krasnov says:

====================
vsock: updates for SO_RCVLOWAT handling

This patchset includes some updates for SO_RCVLOWAT:

1) af_vsock:
   During my experiments with zerocopy receive, i found, that in some
   cases, poll() implementation violates POSIX: when socket has non-
   default SO_RCVLOWAT(e.g. not 1), poll() will always set POLLIN and
   POLLRDNORM bits in 'revents' even number of bytes available to read
   on socket is smaller than SO_RCVLOWAT value. In this case,user sees
   POLLIN flag and then tries to read data(for example using  'read()'
   call), but read call will be blocked, because  SO_RCVLOWAT logic is
   supported in dequeue loop in af_vsock.c. But the same time,  POSIX
   requires that:

   "POLLIN     Data other than high-priority data may be read without
               blocking.
    POLLRDNORM Normal data may be read without blocking."

   See https://www.open-std.org/jtc1/sc22/open/n4217.pdf, page 293.

   So, we have, that poll() syscall returns POLLIN, but read call will
   be blocked.

   Also in man page socket(7) i found that:

   "Since Linux 2.6.28, select(2), poll(2), and epoll(7) indicate a
   socket as readable only if at least SO_RCVLOWAT bytes are available."

   I checked TCP callback for poll()(net/ipv4/tcp.c, tcp_poll()), it
   uses SO_RCVLOWAT value to set POLLIN bit, also i've tested TCP with
   this case for TCP socket, it works as POSIX required.

   I've added some fixes to af_vsock.c and virtio_transport_common.c,
   test is also implemented.

2) virtio/vsock:
   It adds some optimization to wake ups, when new data arrived. Now,
   SO_RCVLOWAT is considered before wake up sleepers who wait new data.
   There is no sense, to kick waiter, when number of available bytes
   in socket's queue < SO_RCVLOWAT, because if we wake up reader in
   this case, it will wait for SO_RCVLOWAT data anyway during dequeue,
   or in poll() case, POLLIN/POLLRDNORM bits won't be set, so such
   exit from poll() will be "spurious". This logic is also used in TCP
   sockets.

3) vmci/vsock:
   Same as 2), but i'm not sure about this changes. Will be very good,
   to get comments from someone who knows this code.

4) Hyper-V:
   As Dexuan Cui mentioned, for Hyper-V transport it is difficult to
   support SO_RCVLOWAT, so he suggested to disable this feature for
   Hyper-V.
====================

Link: https://lore.kernel.org/r/de41de4c-0345-34d7-7c36-4345258b7ba8@sberdevices.ruSigned-off-by: Paolo Abeni <pabeni@redhat.com>

This adds test to check, that when poll() returns POLLIN, POLLRDNORM bits,
next read call won't block.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This adds extra condition to wake up data reader: do it only when number
of readable bytes >= SO_RCVLOWAT. Otherwise, there is no sense to kick
user, because it will wait until SO_RCVLOWAT bytes will be dequeued. This
check is performed in vsock_data_ready().
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This adds extra condition to wake up data reader: do it only when number
of readable bytes >= SO_RCVLOWAT. Otherwise, there is no sense to kick
user,because it will wait until SO_RCVLOWAT bytes will be dequeued. This
check is performed in vsock_data_ready().
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This adds 'vsock_data_ready()' which must be called by transport to kick
sleeping data readers. It checks for SO_RCVLOWAT value before waking
user, thus preventing spurious wake ups. Based on 'tcp_data_ready()' logic.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Passing 1 as the target to notify_poll_in(), we don't honor
what the user has set via SO_RCVLOWAT, going to set POLLIN
and POLLRDNORM, even if we don't have the amount of bytes
expected by the user.

Let's use sock_rcvlowat() to get the right target to pass to
notify_poll_in();
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This callback controls setting of POLLIN, POLLRDNORM output bits of poll()
syscall, but in some cases, it is incorrectly to set it, when socket has
at least 1 bytes of available data. Use 'target' which is already exists.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This callback controls setting of POLLIN, POLLRDNORM output bits of poll()
syscall, but in some cases, it is incorrectly to set it, when socket has
at least 1 bytes of available data. Use 'target' which is already exists.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

For Hyper-V it is quiet difficult to support this socket option,due to
transport internals, so disable it.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This adds transport specific callback for SO_RCVLOWAT, because in some
transports it may be difficult to know current available number of bytes
ready to read. Thus, when SO_RCVLOWAT is set, transport may reject it.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

In rtnetlink_rcv_msg function, the permission for all user operations
is checked except the GET operation, which is the same as the checking
in qdisc. Therefore, remove the user rights check in qdisc.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Message-Id: <20220819041854.83372-1-shaozhengchao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-08-18 (ixgbe)

This series contains updates to ixgbe driver only.

Fabio M. De Francesco replaces kmap() call to page_address() for
rx_buffer->page().

Jeff Daly adds a manual AN-37 restart to help resolve issues with some link
partners.

* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  ixgbe: Manual AN-37 for troublesome link partners for X550 SFI
  ixgbe: Don't call kmap() on page allocated with GFP_ATOMIC
====================

Link: https://lore.kernel.org/r/20220818223402.1294091-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-08-18 (ice)

This series contains updates to ice driver only.

Jesse and Anatolii add support for controlling FCS/CRC stripping via
ethtool.

Anirudh allows for 100M speeds on devices which support it.

Sylwester removes ucast_shared field and the associated dead code related
to it.

Mikael removes non-inclusive language from the driver.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  ice: remove non-inclusive language
  ice: Remove ucast_shared
  ice: Allow 100M speeds for some devices
  ice: Implement FCS/CRC and VLAN stripping co-existence policy
  ice: Implement control of FCS/CRC stripping
====================

Link: https://lore.kernel.org/r/20220818155207.996297-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since commit 129bd7ca ("net: dsa: Prevent usage of NET_DSA_TAG_8021Q
as tagging protocol"), dsa_8021q_netdev_ops no longer exists, so remove
the comment that talks about it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220818143808.2808393-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210228.8635-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210226.8587-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210218.8443-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220818210216.8419-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210215.8395-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210227.8611-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210222.8515-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210220.8491-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210219.8467-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210214.8371-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220818210212.8347-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210206.8299-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210204.8275-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210023.6889-1-wsa+renesas@sang-engineering.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Vladimir Oltean says:

====================
Validate OF nodes for DSA shared ports

This is the first set of measures taken so that more drivers can be
transitioned towards phylink on shared (CPU and DSA) ports some time in
the future. It consists of:

- expanding the DT schema for DSA and related drivers to clarify the new
  requirements.

- introducing warnings for drivers that currently skip phylink due to
  incomplete DT descriptions.

- introducing warning for drivers that currently skip phylink due to
  using platform data (search for struct dsa_chip_data).

- closing the possibility for new(ish) drivers to skip phylink, by
  validating their DT descriptions.

- making the code paths used by shared ports more evident.

- preparing the code paths used by shared ports for further work to fake
  a link description where that is possible.

More details in patch 10/10.

DT binding (patches 1-6) and kernel (7-10) are in principle separable,
but are submitted together since they're part of the same story.

Patches 8 and 9 are DSA cleanups, and patch 7 is a dependency for patch
10.

v1 at
https://patchwork.kernel.org/project/netdevbpf/patch/20220723164635.1621911-1-vladimir.oltean@nxp.com/

v2 at
https://patchwork.kernel.org/project/netdevbpf/patch/20220729132119.1191227-5-vladimir.oltean@nxp.com/

v3 at
https://patchwork.kernel.org/project/netdevbpf/cover/20220806141059.2498226-1-vladimir.oltean@nxp.com/
====================

Link: https://lore.kernel.org/r/20220818115500.2592578-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>