Pull ste_dma40 fixes from Fabio
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The proper place for the main logic of the soft LLP mode is
dwc_scan_descriptors. It prevents to get the transfer unexpectedly aborted in
case the user calls dwc_tx_status.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The driver assumes that hardware has two AHB masters which might not be always
true. In such cases we must not exceed number of the AHB masters present in the
hardware. In the proposed scheme in this patch, we would choose the master with
highest possible number whenever we exceed max AHB masters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Currently descriptors are allocated from normal cacheable memory and that slows
down filling the descriptors, as we need to call cache_coherency routines
afterwards. It would be better to allocate memory for these descriptors from
DMA_COHERENT memory. This would make code much cleaner too.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

the variable chan is dereferenced in line 635, so it is no reason to check
null again in line 641.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

the pointer cfg is dereferenced in line 594, so it's no reason to check null
again in line 620.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The edma_slave_config() implementation depends on the
direction field such that it will not properly configure
a slave channel when called without direction set.

This fixes the implementation so that the slave config
is copied as is and prep_slave_sg() handles the
direction dependent handling. spi-omap2-mcspi and
omap_hsmmc both expose this bug as they configure the
slave channel config from a common path with an unconfigured
direction field.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Clock code was changed to use clk_prepare_enable in:

b707c65 dma/ste_dma40: Fixup clock usage during probe

but clk_disable on probe fail path was not updated.  This patch fix this
by using clk_disable_unprepare in place of clk_disable.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

Some DMA channels may be used by other cores in the SoC.  This patch
modifies the dma interrupt handler to ignore interrupts from unknown
channels.

Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

This patch add support to manage LLI by SW for select phy channels.

There is a HW issue in certain controllers due to which on certain
occassions HW LLI cannot be used on some physical channels.  To avoid
the HW issue on a specific phy channel, the phy channel number can be
added to the list of soft_lli_channels and there after all the transfers
on that channel will use software LLI, for peripheral to memory
transfers.

SoftLLI introduces relink overhead, that could impact performace for
certain use cases.

This is based on a previous patch of Narayanan Gopalakrishnan.

Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

Use internal variables to the cycles to improve code readability, no
functional changes.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

This patch contains various non functional cosmetic fixes.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

This is to keep the active queue for only those transfers which are
actually active in the hardware.  Descriptors will be moved to the done
queue after they are completed in the hardware (interrupt handler) but
before all the cleanup work has been completed (tasklet).

Mostly based on a previous patch by Rabin Vincent.

Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

U8540 DMA controller is different from u9540 we need define new
registers and use them to support handling more than 128 event lines.
Signed-off-by: Tong Liu <tong.liu@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

DMAC_ICFG[0:2]=SCHNB only allows to count 'multiple of 4' physical
channels so it was ok with platforms having 8 channels but cannot be
used for next versions (with 10 or 14 channels).  This patch allows to
provide the number of physical channels for a DMA device via
platform_data, or still rely on SCHNB if platform_data announces 0
channel.
Signed-off-by: Gerald Baeza <gerald.baeza@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

This patch makes existing use_fixed_channel field (of stedma40_chan_cfg
structure) applicable to physical channels.
Signed-off-by: Gerald Baeza <gerald.baeza@stericsson.com>
Tested-by: Yannick Fertre <yannick.fertre@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

Hardware bug: when a logical channel is triggerred by a high priority
destination event line, an extra packet transaction is generated in case
of important data write response latency on previous logical channel A
and if the source transfer of current logical channel B is already
completed and if no other channel with a higher priority than B is
waiting for execution.

Software workaround: do not set the high priority level for the
destination event lines that trigger logical channels.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

The check for runtime suspend is not needed during a regular suspend, as
the framework takes care of this.  This fixes the issue of DMA driver
not letting the system to go to deepsleep in the first attempt.
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

The client is not aware of the maximum burst size in the dma driver.  If
the size exceeds 16 set max to 16.
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

Maximum DMA seg size is (0xffff x data_width).  If max seg
size is not set it deafults to 64k.  This results in failure
if transferring 64k in byte mode.
Large seg sizes may be supported by splitting large transfer.
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

lcpa and lcla are written often and the cache_sync() overhead in writel
is costly, especially for wlan where every single network packet (in RX
mode) corresponds to a separate DMA transfer.
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Reviewed-by: Narayanan Gopalakrishnan <narayanan.gopalakrishnan@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

This patch sets the SSCFG/SDCFG bit[7] PRI only for physical channel
requests with high priority.  For logical channels, this bit will be
zero.
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

The header is used by drivers/dma/amba-pl08x.c, which can be compiled
under x86, where PL080 exists under a PCI-to-AMBA bridge. This patche
moves it where it can be accessed by other architectures, and fixes
all users.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The DMA transfer could not be established if previously it was paused and
terminated. In that case the channel's suspend bit remains set that prevents to
transfer anything until channel is resumed.

The patch adds the dwc_chan_resume() call instead of a plain flag assignment.
That clears the DWC_CFGL_CH_SUSP bit as well during termination.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The same information could be extracted from the struct dma_chan.
The patch introduces helper function dwc_get_data_width() as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The driver requires a custom slave configuration to be present to be able to
make the slave transfers. Nevertheless, in some cases we need only the request
line as an additional information to the generic slave configuration.  The
request line is provided by slave_id parameter of the dma_slave_config
structure. That's why the custom slave configuration could be optional for such
cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Currently the direction value comes from the generic slave configuration
structure and explicitly as a preparation function parameter. The first one is
kinda obsoleted. Thus, we have to store the value passed to the preparation
function somewhere in our structures to be able to use it later. The best
candidate to provide the storage is a custom channel structure. Until now we
still keep and check the direction field of the slave config structure as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

If we don't yet have the platform device for the driver when it is being loaded
we fail to probe the driver. So instead of calling probe() directly we call
platform_driver_register(). It will call the probe() immediately if we have the
device but also makes the driver to work on platforms where the platform device
is created later.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The is_slave_direction helps to check if the transfer type is slave.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The is_slave_direction helps to check if the transfer type is slave.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The is_slave_direction helps to check if the transfer type is slave.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

dma_transfer_direction is a normal enum. It means we can't usually use the
values as bit fields. Let's adjust this check and move it above the usage of
the direction parameter, due to the nature of the following usage of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

dma_transfer_direction is a normal enum. It means we can't usually use the
values as bit fields. Let's adjust this check and move it above the usage of
the direction parameter, due to the nature of the following usage of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This function helps to distinguish the slave type of transfer by checking the
direction parameter.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

We will use at least the dwc_chan_resume() later.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The "else" keyword in the dw_dma_tasklet is removed as well. All together
simplifies the logic of the code and understanding of what is happening there.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

There is no need to check the callback_required parameter, due to we check the
callback pointer to be a non-NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Otherwise we get a warning in case of CONFIG_DMA_API_DEBUG=y

[   45.775943] WARNING: at lib/dma-debug.c:933 check_unmap+0x5d6/0x6ac()
[   45.782369] dw_dmac dw_dmac.0: DMA-API: device driver failed to check map error[device address=0x00000000356efcc0] [size=28 bytes] [mapped as single]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The patch allows to probe the device when platform data is absent and hardware
auto configuration is enabled. In that case the default platform data is used
where the channel allocation order is set to ascending, channel priority is set
to ascending, and private property is set to true.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>