The error paths set err, but it's not returned.

I wondered if we should fix all of the callers to check the returned
value, but Ben explains why the code is this way:

> Most call sites ignore it on purpose. There's nothing we can do if
> we fail to get a buffer at interrupt time, so we point the buffer to
> the scratch page so the HW doesn't DMA into lalaland and lose the
> packet.
>
> The one call site that tests and can fail is the one used when brining
> the interface up. If we fail to allocate at that point, we fail the
> ifup. But as you noticed, I do have a bug not returning the error.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 2465 defines ipv6IfStatsOutFragFails as:

	"The number of IPv6 datagrams that have been discarded
	 because they needed to be fragmented at this output
	 interface but could not be."

The existing implementation, instead, would increase the counter
twice in case we fail to allocate room for single fragments:
once for the fragment, once for the datagram.

This didn't look intentional though. In one of the two affected
affected failure paths, the double increase was simply a result
of a new 'goto fail' statement, introduced to avoid a skb leak.
The other path appears to be affected since at least 2.6.12-rc2.
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Fixes: 1d325d21 ("ipv6: ip6_fragment: fix headroom tests and skb leak")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I forgot one spot when introducing struct test_obj_val.

Fixes: e859afe1 ("lib: test_rhashtable: fix for large entry counts")
Reported by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit e5a03bfd ("phy: Add an mdio_device structure")
introduced a spurious trailing semicolon. Remove it.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paul Moore reported a SELinux/IP_PASSSEC regression
caused by missing skb->sp at recvmsg() time. We need to
preserve the skb head state to process the IP_CMSG_PASSSEC
cmsg.

With this commit we avoid releasing the skb head state in the
BH even if a secpath is attached to the current skb, and stores
the skb status (with/without head states) in the scratch area,
so that we can access it at skb deallocation time, without
incurring in cache-miss penalties.

This also avoids misusing the skb CB for ipv6 packets,
as introduced by the commit 0ddf3fb2 ("udp: preserve
skb->dst if required for IP options processing").

Clean a bit the scratch area helpers implementation, to
reduce the code differences between 32 and 64 bits build.
Reported-by: Paul Moore <paul@paul-moore.com>
Fixes: 0a463c78 ("udp: avoid a cache miss on dequeue")
Fixes: 0ddf3fb2 ("udp: preserve skb->dst if required for IP options processing")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mt7530 driver has its dsa_switch_ops::get_tag_protocol function
check ds->cpu_port_mask to issue a warning in case the configured CPU
port is not capable of supporting tags.

After commit 14be36c2 ("net: dsa: Initialize all CPU and enabled
ports masks in dsa_ds_parse()") we slightly re-arranged the
initialization such that this was no longer working. Just make sure that
ds->cpu_port_mask is set prior to the first call to get_tag_protocol,
thus restoring the expected contract. In case of error, the CPU port bit
is cleared.

Fixes: 14be36c2 ("net: dsa: Initialize all CPU and enabled ports masks in dsa_ds_parse()")
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are multiple reports showing we have a use-after-free in
the timer prb_retire_rx_blk_timer_expired(), where we use struct
tpacket_kbdq_core::pkbdq, a pg_vec, after it gets freed by
free_pg_vec().

The interesting part is it is not freed via packet_release() but
via packet_setsockopt(), which means we are not closing the socket.
Looking into the big and fat function packet_set_ring(), this could
happen if we satisfy the following conditions:

1. closing == 0, not on packet_release() path
2. req->tp_block_nr == 0, we don't allocate a new pg_vec
3. rx_ring->pg_vec is already set as V3, which means we already called
   packet_set_ring() wtih req->tp_block_nr > 0 previously
4. req->tp_frame_nr == 0, pass sanity check
5. po->mapped == 0, never called mmap()

In this scenario we are clearing the old rx_ring->pg_vec, so we need
to free this pg_vec, but we don't stop the timer on this path because
of closing==0.

The timer has to be stopped as long as we need to free pg_vec, therefore
the check on closing!=0 is wrong, we should check pg_vec!=NULL instead.

Thanks to liujian for testing different fixes.

Reported-by: alexander.levin@verizon.com
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Reported-by: liujian (CE) <liujian56@huawei.com>
Tested-by: liujian (CE) <liujian56@huawei.com>
Cc: Ding Tianhong <dingtianhong@huawei.com>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Populate mii_bus->parent with our own platform device before
registering, which makes it easier to locate the MDIO bus
in sysfs when trying to diagnose problems.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

We had reports of 50us not being sufficient to reset the MAC,
thus hitting the "Hardware reset failed" error bringing the
interface up on some AST2400 based machines.

This bumps the timeout to 200us.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before the 'type' is validated, we shouldn't use it to fetch the
ovs_ct_attr_lens's minlen and maxlen, else, out of bound access
may happen.

Fixes: 7f8a436e ("openvswitch: Add conntrack action")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

DMA transfers are not allowed to buffers that are on the stack.
Therefore allocate a buffer to store the result of usb_control_message().

Fixes these bugreports:
https://bugzilla.kernel.org/show_bug.cgi?id=195217

https://bugzilla.redhat.com/show_bug.cgi?id=1421387
https://bugzilla.redhat.com/show_bug.cgi?id=1427398

Shortened kernel backtrace from 4.11.9-200.fc25.x86_64:
kernel: ------------[ cut here ]------------
kernel: WARNING: CPU: 3 PID: 2957 at drivers/usb/core/hcd.c:1587
kernel: transfer buffer not dma capable
kernel: Call Trace:
kernel: dump_stack+0x63/0x86
kernel: __warn+0xcb/0xf0
kernel: warn_slowpath_fmt+0x5a/0x80
kernel: usb_hcd_map_urb_for_dma+0x37f/0x570
kernel: ? try_to_del_timer_sync+0x53/0x80
kernel: usb_hcd_submit_urb+0x34e/0xb90
kernel: ? schedule_timeout+0x17e/0x300
kernel: ? del_timer_sync+0x50/0x50
kernel: ? __slab_free+0xa9/0x300
kernel: usb_submit_urb+0x2f4/0x560
kernel: ? urb_destroy+0x24/0x30
kernel: usb_start_wait_urb+0x6e/0x170
kernel: usb_control_msg+0xdc/0x120
kernel: mcs_get_reg+0x36/0x40 [mcs7780]
kernel: mcs_net_open+0xb5/0x5c0 [mcs7780]
...

Regression goes back to 4.9, so it's a good candidate for -stable.
Though it's the decision of the maintainer.

Thanks to Dan Williams for adding the "transfer buffer not dma capable"
warning in the first place. It instantly pointed me in the right direction.

Patch has been tested with transferring data from a Polar watch.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit fbf68229 ("net: stmmac: unify registers dumps methods")

in the Linux kernel modified the register dump to store the DMA registers
at the DMA register offset (0x1000) but ethtool (stmmac.c) looks for the
DMA registers after the MAC registers which is offset 55.
This patch copies the DMA registers from the higher offset to the offset
where ethtool expects them.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit ffb07550 ("copy_msghdr_from_user(): get rid of
field-by-field copyin") introduce a new sparse warning:

net/socket.c:1919:27: warning: incorrect type in assignment (different address spaces)
net/socket.c:1919:27:    expected void *msg_control
net/socket.c:1919:27:    got void [noderef] <asn:1>*[addressable] msg_control

and a line above 80 chars, let's fix them

Fixes: ffb07550 ("copy_msghdr_from_user(): get rid of field-by-field copyin")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2017-07-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.13

Important, but small in size, fixes.

brcmfmac

* fix a regression in SDIO support introduced in v4.13-rc1

rtlwifi

* fix a regression in bluetooth coexistance introduced in v4.13-rc1

iwlwifi

* a few NULL pointer dereferences in the recovery flow

* a small but important fix for IBSS

* a one-liner fix for tracing, which was including too much data
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Each FIB node holds a linked list of routes sharing the same prefix and
length. In the case of IPv4 it's ordered according to table ID, metric
and TOS and only the first route in the list is actually programmed to
the device.

In case a gatewayed route is added somewhere in the list, then after its
nexthop group will be refreshed and become valid (due to the resolution
of its gateway), it'll mistakenly overwrite the existing entry.

Example:
192.168.200.0/24 dev enp3s0np3 scope link metric 1000 offload
192.168.200.0/24 via 192.168.100.1 dev enp3s0np3 metric 1000 offload

Both routes are marked as offloaded despite the fact only the first one
should actually be present in the device's table.

When refreshing the nexthop group, don't write the route to the device's
table unless it's the first in its node.

Fixes: 9aecce1c ("mlxsw: spectrum_router: Correctly handle identical routes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During concurrent access testing, threadfunc() concatenated thread ID
and object index to create a unique key like so:

| tdata->objs[i].value = (tdata->id << 16) | i;

This breaks if a user passes an entries parameter of 64k or higher,
since 'i' might use more than 16 bits then. Effectively, this will lead
to duplicate keys in the table.

Fix the problem by introducing a struct holding object and thread ID and
using that as key instead of a single integer type field.

Fixes: f4a3e90b ("rhashtable-test: extend to test concurrency")
Reported by: Manuel Messner <mm@skelett.io>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Edward Cree says:

====================
bpf: fix verifier min/max handling in BPF_SUB

I managed to come up with a test for the swapped bounds in BPF_SUB, so here
 it is along with a patch that fixes it, separated out from my 'rewrite
 everything' series so it can go to -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We have to subtract the src max from the dst min, and vice-versa, since
 (e.g.) the smallest result comes from the largest subtrahend.

Fixes: 48461135 ("bpf: allow access into map value arrays")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a bug in the verifier's handling of BPF_SUB: [a,b] - [c,d] yields
 was [a-c, b-d] rather than the correct [a-d, b-c].  So here is a test
 which, with the bogus handling, will produce ranges of [0,0] and thus
 allowed accesses; whereas the correct handling will give a range of
 [-255, 255] (and hence the right-shift will give a range of [0, 255]) and
 the accesses will be rejected.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mediatek ethernet driver uses interrupts but does not explicitly
include linux/interrupt.h, relying on implicit includes.  Fix this so we
don't get build breaks as happened for ARM in next-20170720.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is some codes of tun/tap module which did not check the return
value of register_netdevice_notifier. Add the check now.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Potential dangerous invalid memory might be accessed if invalid mac value
reflected from the forward port field in rxd4 caused by possible potential
hardware defects. So added a simple sanity checker to avoid the kind of
situation happening.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'iwlwifi-for-kalle-2017-07-21' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Some iwlwifi fixes for 4.13:

* A few NULL pointer dereferences in the recovery flow;
* A small but important fix for IBSS;
* A one-liner fix for tracing, which was including too much data;
* Some of these are bugzilla bug fixes;

A hardware/firmware error may happen at any point in time. In
particular, it might happen while mac80211 is in the middle of
a flow. We observed the following situation:
 * mac80211 is in authentication flow, in ieee80211_prep_connection()
 * iwlwifi firmware crashes, but no error can be reported at this
   precise point (mostly because the driver method is void, but even
   if it wasn't we'd just shift to a race condition)
 * mac80211 continues the flow, trying to add the AP station
 * iwlwifi has already set its internal restart flag, and so thinks
   that adding the station is part of the restart and already set up,
   so it uses the information that's supposed to already be in the
   struct

This can happen with any flow in mac80211 and with any information
we try to preserve across hardware restarts.

To fix this, only set a new HW_RESTART_REQUESTED flag and translate
that to IN_HW_RESTART once mac80211 actually starts the restart by
calling our start() method. As a consequence, any mac80211 flow in
progress at the time of the restart will properly finish (certainly
with errors), before the restart is attempted.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299.
Reported-by: djagoo <dev@djagoo.io>
Reported-by: Łukasz Siudut <lsiudut@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When IBSS was implemented for DQA, we missid a few places where it
should be handled in the same way as AP.

Fixes: ee48b722 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwl_trace_data is somewhat confusing. It returns a bool
that tells if the payload of the skb should be added to
the tx_data event. If it returns false, then the payload
of the skb is added to the tx event.

The purpose is to be able to start tracing with
-e iwlwifi
and record non-data packets only which saves bandwidth.

Since EAPOLs are important, seldom and not real data
packet (despite being WiFi data packets), they are
included in tx event and thus iwl_trace_data returns false
on those. This last part was buggy, and because of that,
all the data packets were included in the tx event.

Fix that.

Fixes: 0c4cb731 ("iwlwifi: tracing: decouple from mac80211")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We don't set the error code here so we end up returning ERR_PTR(0) which
is NULL.  The caller doesn't expect that so it results in a NULL
dereference.

Fixes: 2e5d4a8f ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Sometimes, we can have an firmware crash while trying to
recover from a previous firmware problem.
When that happens, lots of things can go wrong. For example
the stations don't get added properly to mvm->fw_id_to_mac_id.

Mac80211 tries to stop A-MPDU upon reconfig but in case of
a firmware crash we will bail out fairly early and in the
end, we won't delete the A-MPDU Rx timeout.
When that timer expired after a double firmware crash,
we end up dereferencing mvm->fw_id_to_mac_id[sta_id]
which is NULL.

Fixes: 10b2b201 ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Before TVQM, all TX queues were allocated straight at init.
With TVQM, queues are allocated on demand and hence we need
to check if a queue exists before dereferencing it.

Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlagn_check_ratid_empty takes the tid as a parameter, but
it doesn't check that it is not IWL_TID_NON_QOS.
Since IWL_TID_NON_QOS = 8 and iwl_priv::tid_data is an array
with 8 entries, accessing iwl_priv::tid_data[IWL_TID_NON_QOS]
is a bad idea.
This happened in iwlagn_rx_reply_tx. Since
iwlagn_check_ratid_empty is relevant only to check whether
we can open A-MPDU, this flow is irrelevant if tid is
IWL_TID_NON_QOS. Call iwlagn_check_ratid_empty only inside
the
	if (tid != IWL_TID_NON_QOS)

a few lines earlier in the function.

Cc: <stable@vger.kernel.org>
Reported-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Tested-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

This reverts commit f95d95a7.

With commit f95d95a7 ("rtlwifi: btcoex: rtl8723be: fix ant_sel not
work"), the kernel has a NULL pointer dereference oops. This content and
the proper fix will be included in a later patch.

Fixes: f95d95a7 ("rtlwifi: btcoex: rtl8723be: fix ant_sel not work")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Recent change in brcmf_sdio_txpkt_hdalign() changed the
behavior and now always returns 0. This resulted in a
regression which basically renders the device useless.

Fixes: 270a6c1f ("brcmfmac: rework headroom check in .start_xmit()")
Reported-by: S. Gilles <sgilles@math.umd.edu>
Tested-by: S. Gilles <sgilles@math.umd.edu>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Pull networking fixes from David Miller:

 1) BPF verifier signed/unsigned value tracking fix, from Daniel
    Borkmann, Edward Cree, and Josef Bacik.

 2) Fix memory allocation length when setting up calls to
    ->ndo_set_mac_address, from Cong Wang.

 3) Add a new cxgb4 device ID, from Ganesh Goudar.

 4) Fix FIB refcount handling, we have to set it's initial value before
    the configure callback (which can bump it). From David Ahern.

 5) Fix double-free in qcom/emac driver, from Timur Tabi.

 6) A bunch of gcc-7 string format overflow warning fixes from Arnd
    Bergmann.

 7) Fix link level headroom tests in ip_do_fragment(), from Vasily
    Averin.

 8) Fix chunk walking in SCTP when iterating over error and parameter
    headers. From Alexander Potapenko.

 9) TCP BBR congestion control fixes from Neal Cardwell.

10) Fix SKB fragment handling in bcmgenet driver, from Doug Berger.

11) BPF_CGROUP_RUN_PROG_SOCK_OPS needs to check for null __sk, from Cong
    Wang.

12) xmit_recursion in ppp driver needs to be per-device not per-cpu,
    from Gao Feng.

13) Cannot release skb->dst in UDP if IP options processing needs it.
    From Paolo Abeni.

14) Some netdev ioctl ifr_name[] NULL termination fixes. From Alexander
    Levin and myself.

15) Revert some rtnetlink notification changes that are causing
    regressions, from David Ahern.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
  net: bonding: Fix transmit load balancing in balance-alb mode
  rds: Make sure updates to cp_send_gen can be observed
  net: ethernet: ti: cpsw: Push the request_irq function to the end of probe
  ipv4: initialize fib_trie prior to register_netdev_notifier call.
  rtnetlink: allocate more memory for dev_set_mac_address()
  net: dsa: b53: Add missing ARL entries for BCM53125
  bpf: more tests for mixed signed and unsigned bounds checks
  bpf: add test for mixed signed and unsigned bounds checks
  bpf: fix up test cases with mixed signed/unsigned bounds
  bpf: allow to specify log level and reduce it for test_verifier
  bpf: fix mixed signed/unsigned derived min/max value bounds
  ipv6: avoid overflow of offset in ip6_find_1stfragopt
  net: tehuti: don't process data if it has not been copied from userspace
  Revert "rtnetlink: Do not generate notifications for CHANGEADDR event"
  net: dsa: mv88e6xxx: Enable CMODE config support for 6390X
  dt-binding: ptp: Add SoC compatibility strings for dte ptp clock
  NET: dwmac: Make dwmac reset unconditional
  net: Zero terminate ifr_name in dev_ifname().
  wireless: wext: terminate ifr name coming from userspace
  netfilter: fix netfilter_net_init() return
  ...

balance-alb mode used to have transmit dynamic load balancing feature
enabled by default.  However, transmit dynamic load balancing no longer
works in balance-alb after commit 8b426dc5 ("bonding: remove
hardcoded value").

Both balance-tlb and balance-alb use the function bond_do_alb_xmit() to
send packets.  This function uses the parameter tlb_dynamic_lb.
tlb_dynamic_lb used to have the default value of 1 for balance-alb, but
now the value is set to 0 except in balance-tlb.

Re-enable transmit dyanmic load balancing by initializing tlb_dynamic_lb
for balance-alb similar to balance-tlb.

Fixes: 8b426dc5 ("bonding: remove hardcoded value")
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

cp->cp_send_gen is treated as a normal variable, although it may be
used by different threads.

This is fixed by using {READ,WRITE}_ONCE when it is incremented and
READ_ONCE when it is read outside the {acquire,release}_in_xmit
protection.

Normative reference from the Linux-Kernel Memory Model:

    Loads from and stores to shared (but non-atomic) variables should
    be protected with the READ_ONCE(), WRITE_ONCE(), and
    ACCESS_ONCE().

Clause 5.1.2.4/25 in the C standard is also relevant.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Push the request_irq function to the end of probe so as
to ensure all the required fields are populated in the event
of an ISR getting executed right after requesting the irq.

Currently while loading the crash kernel a crash was seen as
soon as devm_request_threaded_irq was called. This was due to
n->poll being NULL which is called as part of net_rx_action
function.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Net stack initialization currently initializes fib-trie after the
first call to netdevice_notifier() call. In fact fib_trie initialization
needs to happen before first rtnl_register(). It does not cause any problem
since there are no devices UP at this moment, but trying to bring 'lo'
UP at initialization would make this assumption wrong and exposes the issue.

Fixes following crash

 Call Trace:
  ? alternate_node_alloc+0x76/0xa0
  fib_table_insert+0x1b7/0x4b0
  fib_magic.isra.17+0xea/0x120
  fib_add_ifaddr+0x7b/0x190
  fib_netdev_event+0xc0/0x130
  register_netdevice_notifier+0x1c1/0x1d0
  ip_fib_init+0x72/0x85
  ip_rt_init+0x187/0x1e9
  ip_init+0xe/0x1a
  inet_init+0x171/0x26c
  ? ipv4_offload_init+0x66/0x66
  do_one_initcall+0x43/0x160
  kernel_init_freeable+0x191/0x219
  ? rest_init+0x80/0x80
  kernel_init+0xe/0x150
  ret_from_fork+0x22/0x30
 Code: f6 46 23 04 74 86 4c 89 f7 e8 ae 45 01 00 49 89 c7 4d 85 ff 0f 85 7b ff ff ff 31 db eb 08 4c 89 ff e8 16 47 01 00 48 8b 44 24 38 <45> 8b 6e 14 4d 63 76 74 48 89 04 24 0f 1f 44 00 00 48 83 c4 08
 RIP: kmem_cache_alloc+0xcf/0x1c0 RSP: ffff9b1500017c28
 CR2: 0000000000000014

Fixes: 7b1a74fd ("[NETNS]: Refactor fib initialization so it can handle multiple namespaces.")
Fixes: 7f9b8052 ("[IPV4]: fib hash|trie initialization")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtnet_set_mac_address() interprets mac address as struct
sockaddr, but upper layer only allocates dev->addr_len
which is ETH_ALEN + sizeof(sa_family_t) in this case.

We lack a unified definition for mac address, so just fix
the upper layer, this also allows drivers to interpret it
to struct sockaddr freely.
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The BCM53125 entry was missing an arl_entries member which would
basically prevent the ARL search from terminating properly. This switch
has 4 ARL entries, so add that.

Fixes: 1da6df85 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
BPF map value adjust fix

First patch in the series is the actual fix and the remaining
patches are just updates to selftests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>