[Why]
FIFO reset is only necessary for fast boot sequence, where otg is disabled
and dig fe is enabled when changing dispclk. Fast boot is only enabled
on embedded displays.

[How]
Change FIFO reset condition to "embedded display only".
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCN301 has seamless boot enabled. With MPC split enabled
at the same time, system will hang.

[How]
Revert MPC split policy back to "MPC_SPLIT_AVOID". Since we have
ODM combine enabled on DCN301, pipe split is not necessary here.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

SDMA FW fixes the hang issue for adding heavy-weight TLB
flush on Arcturus, so we can enable it.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Debug VRAM access through SDMA has several broken parts resulting in
silent MMIO fallback.

BO kernel creation takes the location of the cpu addr pointer, not
the pointer itself for address kmap.

drm_dev_enter return true on success so change access check.

The source BO is reserved but not pinned so find the address using the
cursor offset relative to its memory domain start.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

That's just a leftover from old radeon days and was preventing CS and GART
bindings before the hardware was initialized. But nowdays that is
perfectly valid.

The only thing we need to warn about are GART binding before the table
is even allocated.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove set but unused variable.
warning: variable 'umc_reg_offset' set but not used
Signed-off-by: mziya <Mohammadzafar.ziya@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove repeated calls.
Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch will modify a pair of functions for pcie port wreg/rreg.
AMD GPU have had an independent NBIO block from SOC15 arch.
If the dirver wants to read/write the address space of the pcie devices,
it has to go through the NBIO block.
This patch will move the pcie port wreg/rreg functions to
"amdgpu_device.c", so that to reuse the functions on the
future GPU ASICs.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch will add vram check function for GMC block.
It will write pattern data to the vram and then read back from the vram,
so that to verify the work status of vram.
This patch  will cover gmc v6/7/8/9/10.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Return value from amdgpu_bo_create_kernel() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

I met a bug recently and the kernel log:

[  330.171875] radeon 0000:03:00.0: couldn't schedule ib
[  330.175781] [drm:radeon_uvd_suspend [radeon]] *ERROR* Error destroying UVD (-22)!

In radeon drivers, using UVD suspend is as follows:

if (rdev->has_uvd) {
        uvd_v1_0_fini(rdev);
        radeon_uvd_suspend(rdev);
}

In radeon_ib_schedule function, we check the 'ring->ready' state,
but in uvd_v1_0_fini funciton, we've cleared the ready state.
So, just modify the suspend code flow to fix error.
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Qiang Ma <maqianga@uniontech.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, thus a matching decrement is needed
on the error handling path to keep the counter balanced.
Signed-off-by: Yongzhi Liu <lyz_cs@pku.edu.cn>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The calcs folder has FPU code on it, which should be isolated inside the
DML folder as per https://patchwork.freedesktop.org/series/93042/.

This commit aims single-handedly to correct the location of such FPU
code and does not refactor any functions.

Changes since v2:
- Corrected problems to compile when DCN was disabled.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Isabella Basso <isabbasso@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This version brings along following fixes:

- Organize FPU associated code to DML
- Modify SMU_TIMEOUT macro
- Organize dcn201 code
- Address DS stays disabled problem under specific scenario
- Fix black screen issue
- Update DML to rev.99
- Address problem of eDP hot-plug feature
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
For allow eDP hot-plug feature, the stream signal may change to VIRTUAL
when plug-out and back to eDP when plug-in. OS will still setPathMode
with same timing for each plugging, but eDP gets no stream update as we
don't check signal type changing back as keeping it VIRTUAL. It's also
unsafe for future cases that stream signal is switched with same timing.

[How]
Check stream signal type change include previous HDMI signal case.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
1. update dml to rev.99
2. add smu clk table w/a: smu gives 1 dtm level with mismatch votage
   table which causes multiple issues.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
With some monitors when multi plane overlay is enabled the memory
clock switching mechanism has to change and, due to an error in the
initialization sequence, it may cause a black screen.

[HOW]
Change the firmware assisted memory clock switch initialization and
tear-down sequence utilizing the prepare_bandwidth and
optimize_bandwidth contexts.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Felipe Clark <feclark@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
On HG APU + dGPU scenario with no display to dGPU,
DS stays disabled due to no display present.
This problem can be worked around by DAL calling
DCEFCLK DS message to SMU on clk init.

[How]
Call DCEFCLK DS message to SMU on clk init.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
If some SMU features are not enabled, SMU will return fail to that
message.

[HOW]
SMU_TIMEOUT macro will treat "return fail" as timeout also.
Correct the macro to only report timeout case.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why & How]
As part of the FPU isolation work documented in
https://patchwork.freedesktop.org/series/93042/, isolate
code that uses FPU in DCN302 to DML, where all FPU code
should locate.
Co-authored-by: Jasdeep Dhillon <jdhillon@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This version brings improvements in the following:

- Drop unnecessary DCN guards
- Improve Z9 interface
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Need to disable Z9 on configurations that only support Z10

[How]
Support new PMFW interface to disable Z9
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Might potentially have truncation problem with the implicit casting
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
- We only ever want seamless boots on eDPs
- The naming and logic did not match the context

[HOW]
- Removed unnecessary if statements
- Renamed power_down_display_on_boot to seamless_boot_edp_requested and
swapped the logic
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jarif Aftab <jaraftab@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The return value was never initialized so the cleanup code executed when
it isn't even necessary.

Just add proper error handling.

Fixes: ab50cb9d ("drm/radeon/radeon_kms: Fix a NULL pointer dereference in radeon_driver_open_kms()")
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable power level, power limit and fan speed
information retrieval in one VF mode.
This is required so that tool ROCM-SMI
can provide this information to users.
Signed-off-by: Marina Nikolic <Marina.Nikolic@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
This fixes 892deb48 ("drm/amdgpu: Separate vf2pf work item init from virt data exchange").
we should read pf2vf data based at mman.fw_vram_usage_va after gmc
sw_init. commit 892deb48 breaks this logic.

[How]
calling amdgpu_virt_exchange_data in amdgpu_virt_init_data_exchange to
set the right base in the right sequence.

v2:
call amdgpu_virt_init_data_exchange after gmc sw_init to make data
exchange workqueue run

v3:
clean up the code logic

v4:
add some comment and make the code more readable

Fixes: 892deb48 ("drm/amdgpu: Separate vf2pf work item init from virt data exchange")
Signed-off-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Reviewed-by: Horace Chen <horace.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Fix the code style warnings in hdp xgmi mca and umc:
1. WARNING: missing space after struct definition.
2. WARNING: please, no space before tabs.
3. WARNING: line length of xxx exceeds 100 columns.
4. ERROR: "foo* bar" should be "foo *bar".
5. ERROR: space required before the open parenthesis '('.
6. ERROR: space prohibited after that open parenthesis '('.
Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fix the code style warnings in sdma:
1. WARNING: Missing a blank line after declarations.
2. ERROR: that open brace { should be on the previous line.
3. WARNING: unnecessary whitespace before a quoted newline.
4. ERROR: space required after that ',' (ctx:VxV).
Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fix the code style warnings in gmc:
ERROR: space required after that ',' (ctx:VxV).
Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fix the code style warnings in gfx:
1. WARNING: suspect code indent for conditional statements.
2. ERROR: spaces required around that '=' (ctx:WxV).
Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fix the code style warnings in amdgpu_ras:
1. ERROR: space required before the open parenthesis '('.
2. WARNING: line length of xxx exceeds 100 columns.
3. ERROR: "foo* bar" should be "foo *bar".
4. WARNING: unnecessary whitespace before a quoted newline.
5. WARNING: space prohibited before semicolon.
6. WARNING: suspect code indent for conditional statements.
7. WARNING: braces {} are not necessary for single statement blocks.
Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This is a following patch to apply the workaround only on
those boards with a bad harvest table in ip discovery.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Early check in amdgpu_discovery_reg_base_init promises this.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Changed from v1:
    remove unused brace
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

support ECC TABLE message, this table include umc ras error count
and error address

V2:
	Return after smu version check fail

V3:
	Return -EOPNOTSUPP, if fail to get smc ver.

V4:
	ECCTABLE typo corrected and sentence rephrased.
Signed-off-by: mziya <Mohammadzafar.ziya@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

add smu message query error information interface,

function name align with IP version number

V2:
	Removed unused err cnt entry
Signed-off-by: mziya <Mohammadzafar.ziya@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Stanley.Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

update smu driver if version to 0x40

V2:
	Interface version append with sienna_cichlid
V3:
	Aligned with latest driver interface.
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: mziya <Mohammadzafar.ziya@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>