- 14 Dec, 2017 40 commits
-
-
Sean Young authored
Another device with the 0xffdc device id, this one with 0x30 in the config byte. Its an iMON VFD + iMON IR (it does not understand rc6). Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Arvind Yadav authored
The pnp_irq() function returns -1 if an error occurs. pnp_irq() error checking for zero is not correct. Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
-
Chunyan Zhang authored
This patch changes the 32-bit time type (timeval) to the 64-bit one (ktime_t), since 32-bit time types will break in the year 2038. I use ktime_t instead of all uses of timeval in imon.c This patch also changes do_gettimeofday() to ktime_get() accordingly, since ktime_get returns a ktime_t, but do_gettimeofday returns a struct timeval, and the other reason is that ktime_get() uses the monotonic clock. Signed-off-by:
Chunyan Zhang <zhang.chunyan@linaro.org> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Sean Young authored
Once rc_unregister_device() has been called, no driver function should be called. This prevents some nasty race conditions with an ioctl calls driver functions when the driver specific data has been freed. Signed-off-by:
-
Sean Young authored
This makes it possible for lircd to read from a lirc chardev, and not keep it busy. Note that this changes the default for timeout reports to on. lircd already enables timeout reports when it opens a lirc device, leaving them on until the next reboot. Signed-off-by:
-
Sean Young authored
This removes the need for include/media/lirc.h, which just includes the uapi file. Signed-off-by:
-
Sean Young authored
Since removing the lirc kapi, ir-lirc-codec.c only contains lirc fops so the file name is no longer correct. By moving its content into lirc_dev.c the ugly extern struct lirc_fops is not longer needed, and everything lirc related is in one file. Signed-off-by:
-
Sean Young authored
If you try to store u64 in a kfifo (or a struct with u64 members), then the buf member of __STRUCT_KFIFO_PTR will cause 4 bytes padding due to alignment (note that struct __kfifo is 20 bytes on 32 bit). That in turn causes the __is_kfifo_ptr() to fail, which is caught by kfifo_alloc(), which now returns EINVAL. So, ensure that __is_kfifo_ptr() compares to the right structure. Signed-off-by:
Stefani Seibold <stefani@seibold.net> Signed-off-by:
-
Sean Young authored
Now that the lirc interface supports scancodes, RC scancode devices can also have a lirc device. The only receiving feature they will have enabled is LIRC_CAN_REC_SCANCODE. Note that CEC devices have no lirc device, since they can be controlled from their /dev/cecN chardev. Signed-off-by:
-
Sean Young authored
Lirc supports a new mode which requires documentation. Signed-off-by:
-
Sean Young authored
The lirc device should get lirc repeats whether there is a keymap match or not. Signed-off-by:
-
Sean Young authored
This implements LIRC_MODE_SCANCODE reading from the lirc device. The scancode can be read from the input device too, but with this interface you get the rc protocol, keycode, toggle and repeat status in addition to just the scancode. int main() { int fd, mode, rc; fd = open("/dev/lirc0", O_RDWR); mode = LIRC_MODE_SCANCODE; if (ioctl(fd, LIRC_SET_REC_MODE, &mode)) { // kernel too old or lirc does not support transmit } struct lirc_scancode scancode; while (read(fd, &scancode, sizeof(scancode)) == sizeof(scancode)) { printf("protocol:%d scancode:0x%x toggle:%d repeat:%d\n", scancode.rc_proto, scancode.scancode, !!(scancode.flags & LIRC_SCANCODE_FLAG_TOGGLE), !!(scancode.flags & LIRC_SCANCODE_FLAG_REPEAT)); } close(fd); } Signed-off-by: -
Sean Young authored
rc-core has replaced the lirc kapi many years ago, and now with the last driver ported to rc-core, we can finally remove it. Note this has no effect on userspace. All future IR drivers should use the rc-core api. Signed-off-by:
-
Sean Young authored
This is a duplicate of rcdev->driver_name. Signed-off-by:
-
Sean Young authored
Replace the generic kernel lirc api with ones which use rc-core, further reducing the lirc_dev members. Signed-off-by:
-
Sean Young authored
If a lirc chardev is held open after a device is unplugged, rc_close() will be called after rc_unregister_device(). The driver is not expecting any calls at this point, and the iguanair driver causes an oops in this scenario. rc_open() can be called when the device is removed too, by calling open on the chardev whilst the device is being removed. Signed-off-by:
-
Sean Young authored
This is done to further remove the lirc kernel api. Ensure that every fops checks for this. Signed-off-by:
-
Sean Young authored
Since the only mode lirc devices can handle is raw IR, handle this in a plain kfifo. Remove lirc_buffer since this is no longer needed. Signed-off-by:
-
Sean Young authored
Calculate lirc features when necessary, and add LIRC_{S,G}ET_REC_MODE cases to ir_lirc_ioctl. This makes lirc_dev_fop_ioctl() unnecessary since all cases are already handled by ir_lirc_ioctl(). Signed-off-by: -
Sean Young authored
For some IR protocols, some scancode values not valid, i.e. they're part of a different protocol variant. Signed-off-by:
-
Sean Young authored
Ensure we reject an attempt to transmit invalid scancodes. Signed-off-by:
-
Sean Young authored
The lirc user interface exists as a raw decoder, which does not make much sense for transmit-only devices. In addition, we want to have lirc char devices for devices which do not use raw IR, i.e. scancode only devices. Note that rc-code, lirc_dev, ir-lirc-codec are now calling functions of each other, so they've been merged into one module rc-core to avoid circular dependencies. Since ir-lirc-codec no longer exists as separate codec module, there is no need for RC_DRIVER_IR_RAW_TX type drivers to call ir_raw_event_register(). Signed-off-by:
-
Sean Young authored
When sending scancodes, load the encoder if we need it. Signed-off-by:
-
Sean Young authored
If the lirc device supports it, set the carrier for the protocol. Signed-off-by:
-
Sean Young authored
This introduces a new lirc mode: scancode. Any device which can send raw IR can now also send scancodes. int main() { int mode, fd = open("/dev/lirc0", O_RDWR); mode = LIRC_MODE_SCANCODE; if (ioctl(fd, LIRC_SET_SEND_MODE, &mode)) { // kernel too old or lirc does not support transmit } struct lirc_scancode scancode = { .scancode = 0x1e3d, .rc_proto = RC_PROTO_RC5, }; write(fd, &scancode, sizeof(scancode)); close(fd); } The other fields of lirc_scancode must be set to 0. Note that toggle (rc5, rc6) and repeats (nec) are not implemented. Nor is there a method for holding down a key for a period. Signed-off-by: -
Sean Young authored
LIRCCODE is a lirc mode where a driver produces driver-dependent codes for receive and transmit. No driver uses this any more. The LIRC_GET_LENGTH ioctl was used for this mode only. Signed-off-by:
-
Sean Young authored
Now that lirc is no longer in the staging area, remove the entry. Signed-off-by:
-
Sean Young authored
The ir-kbd-i2c driver behaves like the lirc_zilog driver, except it can send raw IR and receives scancodes rather than lirccodes. The lirc_zilog driver only polls if the lirc chardev is opened; similarly the ir-kbd-i2c driver only polls if the corresponding input device is opened, or the lirc device. Polling is disabled during IR transmission through the mutex. The polling period is 402ms in the ir-kdb-i2c driver, and 260ms in the lirc_zilog driver. Signed-off-by:
-
Sean Young authored
This is a fix for commit 329d88da ("[media] media: i2c: Don't export ir-kbd-i2c module alias") that stopped the module from being loaded automagically. The problems described only affect the HD-PVR, so it should not affect other hardware; also if the module happens to be loaded, the i2c IR part of the HD-PVR will be enabled anyway. Fixes: 329d88da ("[media] media: i2c: Don't export ir-kbd-i2c module alias") Signed-off-by:
-
Sean Young authored
This code implements the transmitter which is currently implemented in the staging lirc_zilog driver. The new code does not need a signal database, iow. the haup-ir-blaster.bin firmware file is no longer needed, and the driver does not know anything about the keycodes in that file. Instead, the new driver can send raw IR, but the hardware is limited to few different lengths of pulse and spaces, so it is best to use generated IR rather than recorded IR. Signed-off-by:
-
Sean Young authored
These two devices ids are really just one device with multiple addresses. Probing becomes much simpler if we simply fold this into one i2c device with two address. Note that this breaks the lirc_zilog driver, however we will teach ir-kbd-i2c to do what lirc_zilog does in a later commit. Signed-off-by:
-
Sean Young authored
The lirc_zilog driver only polls the device if the lirc chardev is opened; do the same with the rc-core driver. Signed-off-by:
-
Sean Young authored
Use the dev_dbg dynamic infrastructure instead of rolling our own custom debug logic. Signed-off-by:
-
Sean Young authored
With the parent set for the rc device, the messages clearly state that it is attached via i2c. The additional printk is unnecessary. These are the old messages: rc rc1: i2c IR (Hauppauge WinTV PVR-150 as /devices/virtual/rc/rc1 ir-kbd-i2c: i2c IR (Hauppauge WinTV PVR-150 detected at i2c-10/10-0071/ir0 [ivtv i2c driver #0] Now we simply get: rc rc1: Hauppauge WinTV PVR-150 as /devices/pci0000:00/0000:00:1e.0/0000:02:00.0/i2c-10/10-0071/rc/rc1 Note that we no longer copy the name. I've checked all call sites to verfiy this is not a problem. Signed-off-by:
-
Akinobu Mita authored
When iterating through all endpoints using of_graph_get_next_endpoint(), the refcount of the returned endpoint node is incremented and the refcount of the node which is passed as previous endpoint is decremented. So the caller doesn't need to call of_node_put() for each iterated node except for error exit paths. Otherwise we get "OF: ERROR: Bad of_node_put() on ..." messages. Cc: Hyun Kwon <hyun.kwon@xilinx.com> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Christophe JAILLET authored
This is odd to call 'pci_disable_device()' in an error path before a coresponding successful 'pci_enable_device()'. Return directly instead. Fixes: 77e0be12 ("V4L/DVB (4176): Bug-fix: Fix memory overflow") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Colin Ian King authored
Currently a user can pass in an unsanitized slot number which will lead to and out of range index into ca->slot_info. Fix this by checking that the slot number is no more than the allowed maximum number of slots. Seems that this bug has been in the driver forever. Detected by CoverityScan, CID#139381 ("Untrusted pointer read") Signed-off-by:Colin Ian King <colin.king@canonical.com> Reviewed-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Jasmin Jessich <jasmin@anw.at> Signed-off-by:
-
Gustavo A. R. Silva authored
Add suffix ULL to constant 65535 in order to avoid a potential integer overflow. This constant is used in a context that expects an expression of type u64. Addresses-Coverity-ID: 1056806 Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Stefan Brüns authored
Mygica T230 DVB-T/T2/C USB stick support. It uses the same FX2/Si2168 bridge/demodulator combo as the other devices supported by the driver, but uses the Si2141 tuner. Several DVB-T (MPEG2) and DVB-T2 (H.265) channels were tested, as well as the included remote control. Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by:
-
Dmitry Osipenko authored
NVIDIA Tegra20/30/114/124/132 SoC's have video decoder engine that supports standard set of video formats like H.264 / MPEG-4 / WMV / VC1. Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
