In commit 87d8a9f3 ("rtlwifi: btcoex: call bind to setup btcoex"),
the code turns on a call to exhalbtc_bind_bt_coex_withadapter(). This
routine contains a bug that causes incorrect antenna selection for those
HP laptops with only one antenna and an incorrectly programmed EFUSE.
These boxes are the ones that need the ant_sel module parameter.

Fixes: 87d8a9f3 ("rtlwifi: btcoex: call bind to setup btcoex")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.13+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In commit bcd37f4a ("rtlwifi: btcoex: 23b 2ant: let bt transmit when
hw initialisation done"), there is an additional error when the module
parameter ant_sel is used to select the auxilary antenna. The error is
that the antenna selection is not checked when writing the antenna
selection register.

Fixes: bcd37f4a ("rtlwifi: btcoex: 23b 2ant: let bt transmit when hw initialisation done")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.12+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The net device is already stored in the 'net' variable, so no need to call
dev_net() again.
Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now there is no lock protecting nlk ngroups/groups' accessing in
netlink bind and getname. It's safe from nlk groups' setting in
netlink_release, but not from netlink_realloc_groups called by
netlink_setsockopt.

netlink_lock_table is needed in both netlink bind and getname when
accessing nlk groups.
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ChunYu found a netlink use-after-free issue by syzkaller:

[28448.842981] BUG: KASAN: use-after-free in __nla_put+0x37/0x40 at addr ffff8807185e2378
[28448.969918] Call Trace:
[...]
[28449.117207]  __nla_put+0x37/0x40
[28449.132027]  nla_put+0xf5/0x130
[28449.146261]  sk_diag_fill.isra.4.constprop.5+0x5a0/0x750 [netlink_diag]
[28449.176608]  __netlink_diag_dump+0x25a/0x700 [netlink_diag]
[28449.202215]  netlink_diag_dump+0x176/0x240 [netlink_diag]
[28449.226834]  netlink_dump+0x488/0xbb0
[28449.298014]  __netlink_dump_start+0x4e8/0x760
[28449.317924]  netlink_diag_handler_dump+0x261/0x340 [netlink_diag]
[28449.413414]  sock_diag_rcv_msg+0x207/0x390
[28449.432409]  netlink_rcv_skb+0x149/0x380
[28449.467647]  sock_diag_rcv+0x2d/0x40
[28449.484362]  netlink_unicast+0x562/0x7b0
[28449.564790]  netlink_sendmsg+0xaa8/0xe60
[28449.661510]  sock_sendmsg+0xcf/0x110
[28449.865631]  __sys_sendmsg+0xf3/0x240
[28450.000964]  SyS_sendmsg+0x32/0x50
[28450.016969]  do_syscall_64+0x25c/0x6c0
[28450.154439]  entry_SYSCALL64_slow_path+0x25/0x25

It was caused by no protection between nlk groups' free in netlink_release
and nlk groups' accessing in sk_diag_dump_groups. The similar issue also
exists in netlink_seq_show().

This patch is to defer nlk groups' free in deferred_put_nlk_sk.
Reported-by: ChunYu Wang <chunwang@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 520ac30f ("net_sched: drop packets after root qdisc lock
is released) made a big change of tc for performance. There are two points
left in sch_prio and sch_qfq which are not changed with that commit. Now
enhance them now with __qdisc_drop.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The generic PHY 'phys' property sometime appears in the same node with
the Ethernet PHY 'phy' or 'phy-handle' properties. Add a warning in
phy-bindings.txt to reduce confusion.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull crypto updates from Herbert Xu:
 "Here is the crypto update for 4.14:

  API:
   - Defer scompress scratch buffer allocation to first use.
   - Add __crypto_xor that takes separte src and dst operands.
   - Add ahash multiple registration interface.
   - Revamped aead/skcipher algif code to fix async IO properly.

  Drivers:
   - Add non-SIMD fallback code path on ARM for SVE.
   - Add AMD Security Processor framework for ccp.
   - Add support for RSA in ccp.
   - Add XTS-AES-256 support for CCP version 5.
   - Add support for PRNG in sun4i-ss.
   - Add support for DPAA2 in caam.
   - Add ARTPEC crypto support.
   - Add Freescale RNGC hwrng support.
   - Add Microchip / Atmel ECC driver.
   - Add support for STM32 HASH module"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (116 commits)
  crypto: af_alg - get_page upon reassignment to TX SGL
  crypto: cavium/nitrox - Fix an error handling path in 'nitrox_probe()'
  crypto: inside-secure - fix an error handling path in safexcel_probe()
  crypto: rockchip - Don't dequeue the request when device is busy
  crypto: cavium - add release_firmware to all return case
  crypto: sahara - constify platform_device_id
  MAINTAINERS: Add ARTPEC crypto maintainer
  crypto: axis - add ARTPEC-6/7 crypto accelerator driver
  crypto: hash - add crypto_(un)register_ahashes()
  dt-bindings: crypto: add ARTPEC crypto
  crypto: algif_aead - fix comment regarding memory layout
  crypto: ccp - use dma_mapping_error to check map error
  lib/mpi: fix build with clang
  crypto: sahara - Remove leftover from previous used spinlock
  crypto: sahara - Fix dma unmap direction
  crypto: af_alg - consolidation of duplicate code
  crypto: caam - Remove unused dentry members
  crypto: ccp - select CONFIG_CRYPTO_RSA
  crypto: ccp - avoid uninitialized variable warning
  crypto: serpent - improve __serpent_setkey with UBSAN
  ...

Pull networking updates from David Miller:

 1) Support ipv6 checksum offload in sunvnet driver, from Shannon
    Nelson.

 2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
    Dumazet.

 3) Allow generic XDP to work on virtual devices, from John Fastabend.

 4) Add bpf device maps and XDP_REDIRECT, which can be used to build
    arbitrary switching frameworks using XDP. From John Fastabend.

 5) Remove UFO offloads from the tree, gave us little other than bugs.

 6) Remove the IPSEC flow cache, from Florian Westphal.

 7) Support ipv6 route offload in mlxsw driver.

 8) Support VF representors in bnxt_en, from Sathya Perla.

 9) Add support for forward error correction modes to ethtool, from
    Vidya Sagar Ravipati.

10) Add time filter for packet scheduler action dumping, from Jamal Hadi
    Salim.

11) Extend the zerocopy sendmsg() used by virtio and tap to regular
    sockets via MSG_ZEROCOPY. From Willem de Bruijn.

12) Significantly rework value tracking in the BPF verifier, from Edward
    Cree.

13) Add new jump instructions to eBPF, from Daniel Borkmann.

14) Rework rtnetlink plumbing so that operations can be run without
    taking the RTNL semaphore. From Florian Westphal.

15) Support XDP in tap driver, from Jason Wang.

16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.

17) Add Huawei hinic ethernet driver.

18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
    Delalande.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
  i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
  i40e: avoid NVM acquire deadlock during NVM update
  drivers: net: xgene: Remove return statement from void function
  drivers: net: xgene: Configure tx/rx delay for ACPI
  drivers: net: xgene: Read tx/rx delay for ACPI
  rocker: fix kcalloc parameter order
  rds: Fix non-atomic operation on shared flag variable
  net: sched: don't use GFP_KERNEL under spin lock
  vhost_net: correctly check tx avail during rx busy polling
  net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
  rxrpc: Make service connection lookup always check for retry
  net: stmmac: Delete dead code for MDIO registration
  gianfar: Fix Tx flow control deactivation
  cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
  cxgb4: Fix pause frame count in t4_get_port_stats
  cxgb4: fix memory leak
  tun: rename generic_xdp to skb_xdp
  tun: reserve extra headroom only when XDP is set
  net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
  net: dsa: bcm_sf2: Advertise number of egress queues
  ...

Pull writeback error handling updates from Jeff Layton:
 "This pile continues the work from last cycle on better tracking
  writeback errors. In v4.13 we added some basic errseq_t infrastructure
  and converted a few filesystems to use it.

  This set continues refining that infrastructure, adds documentation,
  and converts most of the other filesystems to use it. The main
  exception at this point is the NFS client"

* tag 'wberr-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
  ecryptfs: convert to file_write_and_wait in ->fsync
  mm: remove optimizations based on i_size in mapping writeback waits
  fs: convert a pile of fsync routines to errseq_t based reporting
  gfs2: convert to errseq_t based writeback error reporting for fsync
  fs: convert sync_file_range to use errseq_t based error-tracking
  mm: add file_fdatawait_range and file_write_and_wait
  fuse: convert to errseq_t based error tracking for fsync
  mm: consolidate dax / non-dax checks for writeback
  Documentation: add some docs for errseq_t
  errseq: rename __errseq_set to errseq_set

Pull file locking updates from Jeff Layton:
 "This pile just has a few file locking fixes from Ben Coddington. There
  are a couple of cleanup patches + an attempt to bring sanity to the
  l_pid value that is reported back to userland on an F_GETLK request.

  After a few gyrations, he came up with a way for filesystems to
  communicate to the VFS layer code whether the pid should be translated
  according to the namespace or presented as-is to userland"

* tag 'locks-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
  locks: restore a warn for leaked locks on close
  fs/locks: Remove fl_nspid and use fs-specific l_pid for remote locks
  fs/locks: Use allocation rather than the stack in fcntl_getlk()

Pull dlm updates from David Teigland:
 "This set includes a bunch of minor code cleanups that have
  accumulated, probably from code analyzers people like to run. There is
  one nice fix that avoids some socket leaks by switching to use
  sock_create_lite()"

* tag 'dlm-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
  dlm: use sock_create_lite inside tcp_accept_from_sock
  uapi linux/dlm_netlink.h: include linux/dlmconstants.h
  dlm: avoid double-free on error path in dlm_device_{register,unregister}
  dlm: constify kset_uevent_ops structure
  dlm: print log message when cluster name is not set
  dlm: Delete an unnecessary variable initialisation in dlm_ls_start()
  dlm: Improve a size determination in two functions
  dlm: Use kcalloc() in two functions
  dlm: Use kmalloc_array() in make_member_array()
  dlm: Delete an error message for a failed memory allocation in dlm_recover_waiters_pre()
  dlm: Improve a size determination in dlm_recover_waiters_pre()
  dlm: Use kcalloc() in dlm_scan_waiters()
  dlm: Improve a size determination in table_seq_start()
  dlm: Add spaces for better code readability
  dlm: Replace six seq_puts() calls by seq_putc()
  dlm: Make dismatch error message more clear
  dlm: Fix kernel memory disclosure

Pull ext4 updates from Ted Ts'o:
 "Scalability improvements when allocating inodes, and some
  miscellaneous bug fixes and cleanups"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: avoid Y2038 overflow in recently_deleted()
  ext4: fix fault handling when mounted with -o dax,ro
  ext4: fix quota inconsistency during orphan cleanup for read-only mounts
  ext4: fix incorrect quotaoff if the quota feature is enabled
  ext4: remove useless test and assignment in strtohash functions
  ext4: backward compatibility support for Lustre ea_inode implementation
  ext4: remove timebomb in ext4_decode_extra_time()
  ext4: use sizeof(*ptr)
  ext4: in ext4_seek_{hole,data}, return -ENXIO for negative offsets
  ext4: reduce lock contention in __ext4_new_inode
  ext4: cleanup goto next group
  ext4: do not unnecessarily allocate buffer in recently_deleted()

Pull XFS updates from Darrick Wong:
 "Here are the changes for xfs for 4.14. Most of these are cleanups and
  fixes for bad behavior, as we're mostly focusing on improving
  reliablity this cycle (read: there's potentially a lot of stuff on the
  horizon for 4.15 so better to spend a few weeks killing other bugs
  now).

  Summary:

   - Write unmount record for a ro mount to avoid unnecessary log replay

   - Clean up orphaned inodes when mounting fs readonly

   - Resubmit inode log items when buffer writeback fails to avoid
     umount hang

   - Fix log recovery corruption problems when log headers wrap around
     the end

   - Avoid infinite loop searching for free inodes when inode counters
     are wrong

   - Evict inodes involved with log redo so that we don't leak them
     later

   - Fix a potential race between reclaim and inode cluster freeing

   - Refactor the inode joining code w.r.t. transaction rolling &
     deferred ops

   - Fix a bug where the log doesn't properly deal with dirty buffers
     that are about to become ordered buffers

   - Fix the extent swap code to deal with making dirty buffers ordered
     properly

   - Consolidate page fault handlers

   - Refactor the incore extent manipulation functions to use the iext
     abstractions instead of directly modifying with extent data

   - Disable crashy chattr +/-x until we fix it

   - Don't allow us to set S_DAX for v2 inodes

   - Various cleanups

   - Clarify some documentation

   - Fix a problem where fsync and a log commit race to send the disk a
     flush command, resulting in a small window where power fail data
     loss could occur

   - Simplify some rmap operations in the fcollapse code

   - Fix some use-after-free problems in async writeback"

* tag 'xfs-4.14-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (44 commits)
  xfs: use kmem_free to free return value of kmem_zalloc
  xfs: open code end_buffer_async_write in xfs_finish_page_writeback
  xfs: don't set v3 xflags for v2 inodes
  xfs: fix compiler warnings
  fsmap: fix documentation of FMR_OF_LAST
  xfs: simplify the rmap code in xfs_bmse_merge
  xfs: remove unused flags arg from xfs_file_iomap_begin_delay
  xfs: fix incorrect log_flushed on fsync
  xfs: disable per-inode DAX flag
  xfs: replace xfs_qm_get_rtblks with a direct call to xfs_bmap_count_leaves
  xfs: rewrite xfs_bmap_count_leaves using xfs_iext_get_extent
  xfs: use xfs_iext_*_extent helpers in xfs_bmap_split_extent_at
  xfs: use xfs_iext_*_extent helpers in xfs_bmap_shift_extents
  xfs: move some code around inside xfs_bmap_shift_extents
  xfs: use xfs_iext_get_extent in xfs_bmap_first_unused
  xfs: switch xfs_bmap_local_to_extents to use xfs_iext_insert
  xfs: add a xfs_iext_update_extent helper
  xfs: consolidate the various page fault handlers
  iomap: return VM_FAULT_* codes from iomap_page_mkwrite
  xfs: relog dirty buffers during swapext bmbt owner change
  ...

Pull GFS2 updates from Bob Peterson:
 "We've got a whopping 29 GFS2 patches for this merge window, mainly
  because we held some back from the previous merge window until we
  could get them perfected and well tested. We have a couple patch sets,
  including my patch set for protecting glock gl_object and Andreas
  Gruenbacher's patch set to fix the long-standing shrink- slab hang,
  plus a bunch of assorted bugs and cleanups.

  Summary:

   - I fixed a bug whereby an IO error would lead to a double-brelse.

   - Andreas Gruenbacher made a minor cleanup to call his relatively new
     function, gfs2_holder_initialized, rather than doing it manually.
     This was just missed by a previous patch set.

   - Jan Kara fixed a bug whereby the SGID was being cleared when
     inheriting ACLs.

   - Andreas found a bug and fixed it in his previous patch, "Get rid of
     flush_delayed_work in gfs2_evict_inode". A call to
     flush_delayed_work was deleted from *gfs2_inode_lookup and added to
     gfs2_create_inode.

   - Wang Xibo found and fixed a list_add call in inode_go_lock that
     specified the parameters in the wrong order.

   - Coly Li submitted a patch to add the REQ_PRIO to some of GFS2's
     metadata reads that were accidentally missing them.

   - I submitted a 4-patch set to protect the glock gl_object field.
     GFS2 was setting and checking gl_object with no locking mechanism,
     so the value was occasionally stomped on, which caused file system
     corruption.

   - I submitted a small cleanup to function gfs2_clear_rgrpd. It was
     needlessly adding rgrp glocks to the lru list, then pulling them
     back off immediately. The rgrp glocks don't use the lru list
     anyway, so doing so was just a waste of time.

   - I submitted a patch that checks the GLOF_LRU flag on a glock before
     trying to remove it from the lru_list. This avoids a lot of
     unnecessary spin_lock contention.

   - I submitted a patch to delete GFS2's debugfs files only after we
     evict all the glocks. Before this patch, GFS2 would delete the
     debugfs files, and if unmount hung waiting for a glock, there was
     no way to debug the problem. Now, if a hang occurs during umount,
     we can examine the debugfs files to figure out why it's hung.

   - Andreas Gruenbacher submitted a patch to fix some trivial typos.

   - Andreas also submitted a five-part patch set to fix the
     longstanding hang involving the slab shrinker: dlm requires memory,
     calls the inode shrinker, which calls gfs2's evict, which calls
     back into DLM before it can evict an inode.

   - Abhi Das submitted a patch to forcibly flush the active items list
     to relieve memory pressure. This fixes a long-standing bug whereby
     GFS2 was getting hung permanently in balance_dirty_pages.

   - Thomas Tai submitted a patch to fix a slab corruption problem due
     to a residual pointer left in the lock_dlm lockstruct.

   - I submitted a patch to withdraw the file system if IO errors are
     encountered while writing to the journals or statfs system file
     which were previously not being sent back up. Before, some IO
     errors were sometimes not be detected for several hours, and at
     recovery time, the journal errors made journal replay impossible.

   - Andreas has a patch to fix an annoying format-truncation compiler
     warning so GFS2 compiles cleanly.

   - I have a patch that fixes a handful of sparse compiler warnings.

   - Andreas fixed up an useless gl_object warning caused by an earlier
     patch.

   - Arvind Yadav added a patch to properly constify our rhashtable
     params declare.

   - I added a patch to fix a regression caused by the non-recursive
     delete and truncate patch that caused file system blocks to not be
     properly freed.

   - Ernesto A. Fernández added a patch to fix a place where GFS2 would
     send back the wrong return code setting extended attributes.

   - Ernesto also added a patch to fix a case in which GFS2 was
     improperly setting an inode's i_mode, potentially granting access
     to the wrong users"

* tag 'gfs2-4.14.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2: (29 commits)
  gfs2: preserve i_mode if __gfs2_set_acl() fails
  gfs2: don't return ENODATA in __gfs2_xattr_set unless replacing
  GFS2: Fix non-recursive truncate bug
  gfs2: constify rhashtable_params
  GFS2: Fix gl_object warnings
  GFS2: Fix up some sparse warnings
  gfs2: Silence gcc format-truncation warning
  GFS2: Withdraw for IO errors writing to the journal or statfs
  gfs2: fix slab corruption during mounting and umounting gfs file system
  gfs2: forcibly flush ail to relieve memory pressure
  gfs2: Clean up waiting on glocks
  gfs2: Defer deleting inodes under memory pressure
  gfs2: gfs2_evict_inode: Put glocks asynchronously
  gfs2: Get rid of gfs2_set_nlink
  gfs2: gfs2_glock_get: Wait on freeing glocks
  gfs2: Fix trivial typos
  GFS2: Delete debugfs files only after we evict the glocks
  GFS2: Don't waste time locking lru_lock for non-lru glocks
  GFS2: Don't bother trying to add rgrps to the lru list
  GFS2: Clear gl_object when deleting an inode in gfs2_delete_inode
  ...

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2017-09-05

This series contains fixes for i40e only.

These two patches fix an issue where our nvmupdate tool does not work on RHEL 7.4
and newer kernels, in fact, the use of the nvmupdate tool on newer kernels can
cause the cards to be non-functional unless these patches are applied.

Anjali reworks the locking around accessing the NVM so that NVM acquire timeouts
do not occur which was causing the failed firmware updates.

Jake correctly updates the wb_desc when reading the NVM through the AdminQ.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When introducing the functions to read the NVM through the AdminQ, we
did not correctly mark the wb_desc.

Fixes: 7073f46e ("i40e: Add AQ commands for NVM Update for X722", 2015-06-05)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

X722 devices use the AdminQ to access the NVM, and this requires taking
the AdminQ lock. Because of this, we lock the AdminQ during
i40e_read_nvm(), which is also called in places where the lock is
already held, such as the firmware update path which wants to lock once
and then unlock when finished after performing several tasks.

Although this should have only affected X722 devices, commit
96a39aed ("i40e: Acquire NVM lock before reads on all devices",
2016-12-02) added locking for all NVM reads, regardless of device
family.

This resulted in us accidentally causing NVM acquire timeouts on all
devices, causing failed firmware updates which left the eeprom in
a corrupt state.

Create unsafe non-locked variants of i40e_read_nvm_word and
i40e_read_nvm_buffer, __i40e_read_nvm_word and __i40e_read_nvm_buffer
respectively. These variants will not take the NVM lock and are expected
to only be called in places where the NVM lock is already held if
needed.

Since the only caller of i40e_read_nvm_buffer() was in such a path,
remove it entirely in favor of the unsafe version. If necessary we can
always add it back in the future.

Additionally, we now need to hold the NVM lock in i40e_validate_checksum
because the call to i40e_calc_nvm_checksum now assumes that the NVM lock
is held. We can further move the call to read I40E_SR_SW_CHECKSUM_WORD
up a bit so that we do not need to acquire the NVM lock twice.

This should resolve firmware updates and also fix potential raise that
could have caused the driver to report an invalid NVM checksum upon
driver load.
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Fixes: 96a39aed ("i40e: Acquire NVM lock before reads on all devices", 2016-12-02)
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Iyappan Subramanian says:

====================
drivers: net: xgene: Misc bug fixes

This patch set fixes bugs related to handling the case for ACPI for,
reading and programming tx/rx delay values.
====================
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 183db4 ("drivers: net: xgene: Correct probe sequence handling")
changed the return type of xgene_enet_check_phy_handle() to void.

This patch, removes the return statement from the last line.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes configuring tx/rx delay values for ACPI.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes reading tx/rx delay values for ACPI.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function calls to kcalloc use wrong parameter order and incorrect flags
values. GFP_KERNEL is used instead of flags now and the order is corrected.

The change was done using the following coccinelle script:

@@
expression E1,E2;
type T;
@@

-kcalloc(E1, E2, sizeof(T))
+kcalloc(E2, sizeof(T), GFP_KERNEL)
Signed-off-by: Zahari Doychev <zahari.doychev@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bits in m_flags in struct rds_message are used for a plurality of
reasons, and from different contexts. To avoid any missing updates to
m_flags, use the atomic set_bit() instead of the non-atomic equivalent.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new TC IDR code uses GFP_KERNEL under spin lock.  Which leads
to:

[  582.621091] BUG: sleeping function called from invalid context at ../mm/slab.h:416
[  582.629721] in_atomic(): 1, irqs_disabled(): 0, pid: 3379, name: tc
[  582.636939] 2 locks held by tc/3379:
[  582.641049]  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff910354ce>] rtnetlink_rcv_msg+0x92e/0x1400
[  582.650958]  #1:  (&(&tn->idrinfo->lock)->rlock){+.-.+.}, at: [<ffffffff9110a5e0>] tcf_idr_create+0x2f0/0x8e0
[  582.662217] Preemption disabled at:
[  582.662222] [<ffffffff9110a5e0>] tcf_idr_create+0x2f0/0x8e0
[  582.672592] CPU: 9 PID: 3379 Comm: tc Tainted: G        W       4.13.0-rc7-debug-00648-g43503a79b9f0 #287
[  582.683432] Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.3.4 11/08/2016
[  582.691937] Call Trace:
...
[  582.742460]  kmem_cache_alloc+0x286/0x540
[  582.747055]  radix_tree_node_alloc.constprop.6+0x4a/0x450
[  582.753209]  idr_get_free_cmn+0x627/0xf80
...
[  582.815525]  idr_alloc_cmn+0x1a8/0x270
...
[  582.833804]  tcf_idr_create+0x31b/0x8e0
...

Try to preallocate the memory with idr_prealloc(GFP_KERNEL)
(as suggested by Eric Dumazet), and change the allocation
flags under spin lock.

Fixes: 65a206c0 ("net/sched: Change act_api and act_xxx modules to use IDR")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We check tx avail through vhost_enable_notify() in the past which is
wrong since it only checks whether or not guest has filled more
available buffer since last avail idx synchronization which was just
done by vhost_vq_avail_empty() before. What we really want is checking
pending buffers in the avail ring. Fix this by calling
vhost_vq_avail_empty() instead.

This issue could be noticed by doing netperf TCP_RR benchmark as
client from guest (but not host). With this fix, TCP_RR from guest to
localhost restores from 1375.91 trans per sec to 55235.28 trans per
sec on my laptop (Intel(R) Core(TM) i7-5600U CPU @ 2.60GHz).

Fixes: 03088137 ("vhost_net: basic polling support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mdio_mux_init() use the parameter dev for two distinct thing:
1) Have a device for all devm_ functions
2) Get device_node from it

Since it is two distinct purpose, this patch add a parameter mdio_mux
that is linked to task 2.

This will also permit to register an of_node mdio-mux that lacks a direct
owning device.
For example a mdio-mux which is a subnode of a real device.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an RxRPC service packet comes in, the target connection is looked up
by an rb-tree search under RCU and a read-locked seqlock; the seqlock retry
check is, however, currently skipped if we got a match, but probably
shouldn't be in case the connection we found gets replaced whilst we're
doing a search.

Make the lookup procedure always go through need_seqretry(), even if the
lookup was successful.  This makes sure we always pick up on a write-lock
event.

On the other hand, since we don't take a ref on the object, but rely on RCU
to prevent its destruction after dropping the seqlock, I'm not sure this is
necessary.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This code is no longer used, the logging function was changed by commit
fbca1647 ("net: stmmac: Use the right logging function in stmmac_mdio_register").
It was previously showing information about the type of the IRQ, if it's
polled, ignored or a normal interrupt. As we don't want information loss,
I have moved this code to phy_attached_print().

Fixes: fbca1647 ("net: stmmac: Use the right logging function in stmmac_mdio_register")
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The wrong register is checked for the Tx flow control bit,
it should have been maccfg1 not maccfg2.
This went unnoticed for so long probably because the impact is
hardly visible, not to mention the tangled code from adjust_link().
First, link flow control (i.e. handling of Rx/Tx link level pause frames)
is disabled by default (needs to be enabled via 'ethtool -A').
Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few
old boards), which results in Tx flow control remaining always on
once activated.

Fixes: 45b679c9 ("gianfar: Implement PAUSE frame generation support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MPS_TX_INT_CAUSE[Bubble] is a normal condition for T6, hence
ignore this interrupt for T6.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MPS_STAT_CTL[CountPauseStatTx] and MPS_STAT_CTL[CountPauseStatRx]
only control whether or not Pause Frames will be counted as part
of the 64-Byte Tx/Rx Frame counters.  These bits do not control
whether Pause Frames are counted in the Total Tx/Rx Frames/Bytes
counters.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

do not reuse the loop counter which is used iterate over
the ports, so that sched_tbl will be freed for all the ports.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename "generic_xdp" to "skb_xdp" to avoid confusing it with the
generic XDP which will be done at netif_receive_skb().

Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We reserve headroom unconditionally which could cause unnecessary
stress on socket memory accounting because of increased trusesize. Fix
this by only reserve extra headroom when XDP is set.

Cc: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull device properties framework updates from Rafael Wysocki:
 "These introduce fwnode operations for all of the separate types of
  'firmware nodes' that can be handled by the device properties
  framework, make the framework use const fwnode arguments all over, add
  a helper for the consolidated handling of node references and switch
  over the framework to the new UUID API.

  Specifics:

   - Introduce fwnode operations for all of the separate types of
     'firmware nodes' that can be handled by the device properties
     framework and drop the type field from struct fwnode_handle (Sakari
     Ailus, Arnd Bergmann).

   - Make the device properties framework use const fwnode arguments
     where possible (Sakari Ailus).

   - Add a helper for the consolidated handling of node references to
     the device properties framework (Sakari Ailus).

   - Switch over the ACPI part of the device properties framework to the
     new UUID API (Andy Shevchenko)"

* tag 'devprop-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: device property: Switch to use new generic UUID API
  device property: export irqchip_fwnode_ops
  device property: Introduce fwnode_property_get_reference_args
  device property: Constify fwnode property API
  device property: Constify argument to pset fwnode backend
  ACPI: Constify internal fwnode arguments
  ACPI: Constify acpi_bus helper functions, switch to macros
  ACPI: Prepare for constifying acpi_get_next_subnode() fwnode argument
  device property: Get rid of struct fwnode_handle type field
  ACPI: Use IS_ERR_OR_NULL() instead of non-NULL check in is_acpi_data_node()

Pull ACPI updates from Rafael Wysocki:
 "These include a usual ACPICA code update (this time to upstream
  revision 20170728), a fix for a boot crash on some systems with
  Thunderbolt devices connected at boot time, a rework of the handling
  of PCI bridges when setting up device wakeup, new support for Apple
  device properties, support for DMA configurations reported via ACPI on
  ARM64, APEI-related updates, ACPI EC driver updates and assorted minor
  modifications in several places.

  Specifics:

   - Update the ACPICA code in the kernel to upstream revision 20170728
     including:
      * Alias operator handling update (Bob Moore).
      * Deferred resolution of reference package elements (Bob Moore).
      * Support for the _DMA method in walk resources (Bob Moore).
      * Tables handling update and support for deferred table
        verification (Lv Zheng).
      * Update of SMMU models for IORT (Robin Murphy).
      * Compiler and disassembler updates (Alex James, Erik Schmauss,
        Ganapatrao Kulkarni, James Morse).
      * Tools updates (Erik Schmauss, Lv Zheng).
      * Assorted minor fixes and cleanups (Bob Moore, Kees Cook, Lv
        Zheng, Shao Ming).

   - Rework the initialization of non-wakeup GPEs with method handlers
     in order to address a boot crash on some systems with Thunderbolt
     devices connected at boot time where we miss an early hotplug event
     due to a delay in GPE enabling (Rafael Wysocki).

   - Rework the handling of PCI bridges when setting up ACPI-based
     device wakeup in order to avoid disabling wakeup for bridges
     prematurely (Rafael Wysocki).

   - Consolidate Apple DMI checks throughout the tree, add support for
     Apple device properties to the device properties framework and use
     these properties for the handling of I2C and SPI devices on Apple
     systems (Lukas Wunner).

   - Add support for _DMA to the ACPI-based device properties lookup
     code and make it possible to use the information from there to
     configure DMA regions on ARM64 systems (Lorenzo Pieralisi).

   - Fix several issues in the APEI code, add support for exporting the
     BERT error region over sysfs and update APEI MAINTAINERS entry with
     reviewers information (Borislav Petkov, Dongjiu Geng, Loc Ho, Punit
     Agrawal, Tony Luck, Yazen Ghannam).

   - Fix a potential initialization ordering issue in the ACPI EC driver
     and clean it up somewhat (Lv Zheng).

   - Update the ACPI SPCR driver to extend the existing XGENE 8250
     workaround in it to a new platform (m400) and to work around an
     Xgene UART clock issue (Graeme Gregory).

   - Add a new utility function to the ACPI core to support using ACPI
     OEM ID / OEM Table ID / Revision for system identification in
     blacklisting or similar and switch over the existing code already
     using this information to this new interface (Toshi Kani).

   - Fix an xpower PMIC issue related to GPADC reads that always return
     0 without extra pin manipulations (Hans de Goede).

   - Add statements to print debug messages in a couple of places in the
     ACPI core for easier diagnostics (Rafael Wysocki).

   - Clean up the ACPI processor driver slightly (Colin Ian King, Hanjun
     Guo).

   - Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).

   - Add a quirk for Dell OptiPlex 9020M to the ACPI backlight driver
     (Alex Hung).

   - Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
     Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
     Ronald Tschalär, Sumeet Pawnikar)"

* tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits)
  ACPI / APEI: Suppress message if HEST not present
  intel_pstate: convert to use acpi_match_platform_list()
  ACPI / blacklist: add acpi_match_platform_list()
  ACPI, APEI, EINJ: Subtract any matching Register Region from Trigger resources
  ACPI: make device_attribute const
  ACPI / sysfs: Extend ACPI sysfs to provide access to boot error region
  ACPI: APEI: fix the wrong iteration of generic error status block
  ACPI / processor: make function acpi_processor_check_duplicates() static
  ACPI / EC: Clean up EC GPE mask flag
  ACPI: EC: Fix possible issues related to EC initialization order
  ACPI / PM: Add debug statements to acpi_pm_notify_handler()
  ACPI: Add debug statements to acpi_global_event_handler()
  ACPI / scan: Enable GPEs before scanning the namespace
  ACPICA: Make it possible to enable runtime GPEs earlier
  ACPICA: Dispatch active GPEs at init time
  ACPI: SPCR: work around clock issue on xgene UART
  ACPI: SPCR: extend XGENE 8250 workaround to m400
  ACPI / LPSS: Don't abort ACPI scan on missing mem resource
  mailbox: pcc: Drop uninformative output during boot
  ACPI/IORT: Add IORT named component memory address limits
  ...

Pull power management updates from Rafael Wysocki:
 "This time (again) cpufreq gets the majority of changes which mostly
  are driver updates (including a major consolidation of intel_pstate),
  some schedutil governor modifications and core cleanups.

  There also are some changes in the system suspend area, mostly related
  to diagnostics and debug messages plus some renames of things related
  to suspend-to-idle. One major change here is that suspend-to-idle is
  now going to be preferred over S3 on systems where the ACPI tables
  indicate to do so and provide requsite support (the Low Power Idle S0
  _DSM in particular). The system sleep documentation and the tools
  related to it are updated too.

  The rest is a few cpuidle changes (nothing major), devfreq updates,
  generic power domains (genpd) framework updates and a few assorted
  modifications elsewhere.

  Specifics:

   - Drop the P-state selection algorithm based on a PID controller from
     intel_pstate and make it use the same P-state selection method
     (based on the CPU load) for all types of systems in the active mode
     (Rafael Wysocki, Srinivas Pandruvada).

   - Rework the cpufreq core and governors to make it possible to take
     cross-CPU utilization updates into account and modify the schedutil
     governor to actually do so (Viresh Kumar).

   - Clean up the handling of transition latency information in the
     cpufreq core and untangle it from the information on which drivers
     cannot do dynamic frequency switching (Viresh Kumar).

   - Add support for new SoCs (MT2701/MT7623 and MT7622) to the mediatek
     cpufreq driver and update its DT bindings (Sean Wang).

   - Modify the cpufreq dt-platdev driver to autimatically create
     cpufreq devices for the new (v2) Operating Performance Points (OPP)
     DT bindings and update its whitelist of supported systems (Viresh
     Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen, Finley
     Xiao).

   - Add support for Ux500 to the cpufreq-dt driver and drop the
     obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).

   - Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
     Nguyen).

   - Fix and clean up assorted issues in the cpufreq drivers and core
     (Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
     Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).

   - Update the IO-wait boost handling in the schedutil governor to make
     it less aggressive (Joel Fernandes).

   - Rework system suspend diagnostics to make it print fewer messages
     to the kernel log by default, add a sysfs knob to allow more
     suspend-related messages to be printed and add Low Power S0 Idle
     constraints checks to the ACPI suspend-to-idle code (Rafael
     Wysocki, Srinivas Pandruvada).

   - Prefer suspend-to-idle over S3 on ACPI-based systems with the
     ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
     interface present in the ACPI tables (Rafael Wysocki).

   - Update documentation related to system sleep and rename a number of
     items in the code to make it cleare that they are related to
     suspend-to-idle (Rafael Wysocki).

   - Export a variable allowing device drivers to check the target
     system sleep state from the core system suspend code (Florian
     Fainelli).

   - Clean up the cpuidle subsystem to handle the polling state on x86
     in a more straightforward way and to use %pOF instead of full_name
     (Rafael Wysocki, Rob Herring).

   - Update the devfreq framework to fix and clean up a few minor issues
     (Chanwoo Choi, Rob Herring).

   - Extend diagnostics in the generic power domains (genpd) framework
     and clean it up slightly (Thara Gopinath, Rob Herring).

   - Fix and clean up a couple of issues in the operating performance
     points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).

   - Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
     (AVS) driver (David Wu).

   - Fix the usage of notifiers in CPU power management on some
     platforms (Alex Shi).

   - Update the pm-graph system suspend/hibernation and boot profiling
     utility (Todd Brandt).

   - Make it possible to run the cpupower utility without CPU0 (Prarit
     Bhargava)"

* tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (87 commits)
  cpuidle: Make drivers initialize polling state
  cpuidle: Move polling state initialization code to separate file
  cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol
  cpufreq: imx6q: Fix imx6sx low frequency support
  cpufreq: speedstep-lib: make several arrays static, makes code smaller
  PM: docs: Delete the obsolete states.txt document
  PM: docs: Describe high-level PM strategies and sleep states
  PM / devfreq: Fix memory leak when fail to register device
  PM / devfreq: Add dependency on PM_OPP
  PM / devfreq: Move private devfreq_update_stats() into devfreq
  PM / devfreq: Convert to using %pOF instead of full_name
  PM / AVS: rockchip-io: add io selectors and supplies for RV1108
  cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
  cpufreq: dt-platdev: Drop few entries from whitelist
  cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
  ARM: ux500: don't select CPUFREQ_DT
  cpuidle: Convert to using %pOF instead of full_name
  cpufreq: Convert to using %pOF instead of full_name
  PM / Domains: Convert to using %pOF instead of full_name
  cpufreq: Cap the default transition delay value to 10 ms
  ...

Pull HID update from Jiri Kosina:

 - Wacom driver fixes/updates (device name generation improvements,
   touch ring status support) from Jason Gerecke

 - T100 touchpad support from Hans de Goede

 - support for batteries driven by HID input reports, from Dmitry
   Torokhov

 - Arnd pointed out that driver_lock semaphore is superfluous, as driver
   core already provides all the necessary concurency protection.
   Removal patch from Binoy Jayan

 - logical minimum numbering improvements in sensor-hub driver, from
   Srinivas Pandruvada

 - support for Microsoft Win8 Wireless Radio Controls extensions from
   João Paulo Rechi Vita

 - assorted small fixes and device ID additions

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (28 commits)
  HID: prodikeys: constify snd_rawmidi_ops structures
  HID: sensor: constify platform_device_id
  HID: input: throttle battery uevents
  HID: usbmouse: constify usb_device_id and fix space before '[' error
  HID: usbkbd: constify usb_device_id and fix space before '[' error.
  HID: hid-sensor-hub: Force logical minimum to 1 for power and report state
  HID: wacom: Do not completely map WACOM_HID_WD_TOUCHRINGSTATUS usage
  HID: asus: Add T100CHI bluetooth keyboard dock touchpad support
  HID: ntrig: constify attribute_group structures.
  HID: logitech-hidpp: constify attribute_group structures.
  HID: sensor: constify attribute_group structures.
  HID: multitouch: constify attribute_group structures.
  HID: multitouch: use proper symbolic constant for 0xff310076 application
  HID: multitouch: Support Asus T304UA media keys
  HID: multitouch: Support HID_GD_WIRELESS_RADIO_CTLS
  HID: input: optionally use device id in battery name
  HID: input: map digitizer battery usage
  HID: Remove the semaphore driver_lock
  HID: wacom: add USB_HID dependency
  HID: add ALWAYS_POLL quirk for Logitech 0xc077
  ...