This patch is

By sh2
- Remove duplicate code
- Reduce stack usage
- Cleanup and little optimize

By sh2a
- Add missing handler(256 to 511)
- Use sh2a instructions handler
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

updated the following codes for Solution Endine 7343:
 - fix compile error in arch/sh/boards/se/7343/irq.c
 - add nor flash physmaps
 - update defconfig
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

updated the following codes for SH7343:
 - add register_intc_controller()
 - add EARLY_SCIF_CONSOLE_PORT
 - add define of CPG register
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Remove inline from ptep_get_and_clean() to match with header file prototype.
Makes linux-next build.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch enables I2C on the sh7723-based ap325rxa board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds platform data for the single I2C channel on sh7366.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds platform data for the single I2C channel on sh7723.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds platform data for two I2C channels to the sh7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The current kernel behaviour is to reenable interrupts unconditionally
when taking a page fault. This patch changes this to only enable them
if interrupts were previously enabled.

It also fixes a problem seen with this fix in place: the kernel previously
flushed the vsyscall page when handling a signal, which is not only
unncessary, but caused a possible sleep with interrupts disabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add implementation of flush_icache_range() suitable for signal handler
and kprobes. Remove flush_cache_sigtramp() and change signal.c to use
flush_icache_range().
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

- Add EtherC + PHY resource define.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sh_pcic_io_xxx function are very old.
In linux-2.4, mrshpc_ss socket driver used this function.
But there is not this driver to the present kernel.
I deleted these cords and checked operation.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The CPU of AP-325RXA is SH7723, but a CPU becomes selectable.
This patch fixes this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Enable SH-Ether support and NFS userland support.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add support SH-Ether for Hitachi Solution Engine.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch contains the following cleanups:
- make the following needlessly global code static:
  - cf-enabler.c: cf_init()
  - cpu/clock.c: __clk_enable()
  - cpu/clock.c: __clk_disable()
  - process_32.c: default_idle()
  - time_32.c: struct clocksource_sh
  - timers/timer-tmu.c: struct tmu_timer_ops
- remove the following unused functions (no CONFIG_BLK_DEV_FD on sh):
  - process_{32,64}.c: disable_hlt()
  - process_{32,64}.c: enable_hlt()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch makes the needlessly global pcibios_max_latency static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch makes the needlessly global EARLY_PCI_OP's static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch makes the needlessly global aica_rtc_{get,set}timeofday()
static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The connect and disconnect functions are unnecessary - everything they do can be
accomplished in the initial probe - so remove them.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds basic support for the SH7763RDP board.
This supports a basic stuff provided in SH7763, like SCIF,
NOR Flash and USB host.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This board is SH7723 base board.

This has SCIF, LCDC, USB Host controler, NOR/NAND Flash, Sound,
Ether and other.

This patch supports SCIF, NOR Flash.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This consolidates everything but the bare assembly routines, which we
will sync up in a follow-up patch.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

16kB is a useful size on nommu, while 64kB still tends to be too big to
be useful. Newer MMUs are likely to support this as well, so plug it
in in anticipation of those, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

PAGE_SIZE doesn't need to be fixed at 4096 on nommu, so stub in a !MMU
case for the various PAGE_SIZE Kconfig options.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This moves get_fs/set_fs() and friends in to asm/segment.h. The
mm_segment_t definition is likewise consolidated from the _32/_64 split.

This is prepatory groundwork for using the generic address space limit
and verification routines across mmu/nommu configs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This adds initial support for the RTE RSK+ SH7203 board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Currently this is only linked in for CONFIG_BINFMT_ELF, make it dependent
on CONFIG_ELF_CORE, so it's both selectable there and also linked in for
CONFIG_BINFMT_ELF_FDPIC.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This adds initial support for ELF FDPIC on MMU-less SH, as per version
0.2 of the ABI definition at:

	http://www.codesourcery.com/public/docs/sh-fdpic/sh-fdpic-abi.txtSigned-off-by: Paul Mundt <lethal@linux-sh.org>

While implementing binfmt_elf_fdpic on SH it quickly became apparent
that SH was the first platform to support both binfmt_elf_fdpic and
binfmt_elf, as well as the only of the FDPIC platforms to make use of the
auxvt.

Currently binfmt_elf_fdpic uses a special version of NEW_AUX_ENT() where
the first argument is the entry displacement after csp has been adjusted,
being reset after each adjustment. As we have no ability to sort this out
through the platform's ARCH_DLINFO, this index needs to be managed
entirely in create_elf_fdpic_tables(). Presently none of the platforms
that set their own auxvt entries are able to do so through their
respective ARCH_DLINFOs when using binfmt_elf_fdpic.

In addition to this, binfmt_elf_fdpic has been looking at
DLINFO_ARCH_ITEMS for the number of architecture-specific entries in the
auxvt. This is legacy cruft, and is not defined by any platforms in-tree,
even those that make heavy use of the auxvt. AT_VECTOR_SIZE_ARCH is
always available, and contains the number that is of interest here, so we
switch to using that unconditionally as well.

As this has direct bearing on how much stack is used, platforms that have
configurable (or dynamically adjustable) NEW_AUX_ENT calls need to either
make AT_VECTOR_SIZE_ARCH more fine-grained, or leave it as a worst-case
and live with some lost stack space if those entries aren't pushed (some
platforms may also need to purposely sacrifice some space here for
alignment considerations, as noted in the code -- although not an issue
for any FDPIC-capable platform today).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Howells <dhowells@redhat.com>

EXPORT_SYMBOL's in lib-y considered harmful:

<--  snip  -->

...
  MODPOST 1837 modules
ERROR: "__raw_readsl" [drivers/ssb/ssb.ko] undefined!
ERROR: "__raw_writesl" [drivers/ssb/ssb.ko] undefined!
ERROR: "__raw_writesl" [drivers/net/smc91x.ko] undefined!
ERROR: "__raw_readsl" [drivers/net/smc91x.ko] undefined!
ERROR: "__raw_writesl" [drivers/net/3c59x.ko] undefined!
ERROR: "__raw_readsl" [drivers/net/3c59x.ko] undefined!
...
make[2]: *** [__modpost] Error 1

<--  snip  -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>