- 15 Feb, 2014 5 commits
-
-
Nat Gurumoorthy authored
[ Upstream commit 388d3335 ] The new tg3 driver leaves REG_BASE_ADDR (PCI config offset 120) uninitialized. From power on reset this register may have garbage in it. The Register Base Address register defines the device local address of a register. The data pointed to by this location is read or written using the Register Data register (PCI config offset 128). When REG_BASE_ADDR has garbage any read or write of Register Data Register (PCI 128) will cause the PCI bus to lock up. The TCO watchdog will fire and bring down the system. Signed-off-by:
Nat Gurumoorthy <natg@google.com> Acked-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Changli Gao authored
[ Upstream commit d323e92c ] maxattr in genl_family should be used to save the max attribute type, but not the max command type. Drop monitor doesn't support any attributes, so we should leave it as zero. Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit a3300ef4 ] Brett Ciphery reported that new ipv6 addresses failed to get installed because the addrconf generated dsts where counted against the dst gc limit. We don't need to count those routes like we currently don't count administratively added routes. Because the max_addresses check enforces a limit on unbounded address generation first in case someone plays with router advertisments, we are still safe here. Reported-by:
Brett Ciphery <brett.ciphery@windriver.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Venkat Venkatsubra authored
[ Upstream commit 18fc25c9 ] After congestion update on a local connection, when rds_ib_xmit returns less bytes than that are there in the message, rds_send_xmit calls back rds_ib_xmit with an offset that causes BUG_ON(off & RDS_FRAG_SIZE) to trigger. For a 4Kb PAGE_SIZE rds_ib_xmit returns min(8240,4096)=4096 when actually the message contains 8240 bytes. rds_send_xmit thinks there is more to send and calls rds_ib_xmit again with a data offset "off" of 4096-48(rds header) =4048 bytes thus hitting the BUG_ON(off & RDS_FRAG_SIZE) [RDS_FRAG_SIZE=4k]. The commit 6094628b "rds: prevent BUG_ON triggering on congestion map updates" introduced this regression. That change was addressing the triggering of a different BUG_ON in rds_send_xmit() on PowerPC architecture with 64Kbytes PAGE_SIZE: BUG_ON(ret != 0 && conn->c_xmit_sg == rm->data.op_nents); This was the sequence it was going through: (rds_ib_xmit) /* Do not send cong updates to IB loopback */ if (conn->c_loopback && rm->m_inc.i_hdr.h_flags & RDS_FLAG_CONG_BITMAP) { rds_cong_map_updated(conn->c_fcong, ~(u64) 0); return sizeof(struct rds_header) + RDS_CONG_MAP_BYTES; } rds_ib_xmit returns 8240 rds_send_xmit: c_xmit_data_off = 0 + 8240 - 48 (rds header accounted only the first time) = 8192 c_xmit_data_off < 65536 (sg->length), so calls rds_ib_xmit again rds_ib_xmit returns 8240 rds_send_xmit: c_xmit_data_off = 8192 + 8240 = 16432, calls rds_ib_xmit again and so on (c_xmit_data_off 24672,32912,41152,49392,57632) rds_ib_xmit returns 8240 On this iteration this sequence causes the BUG_ON in rds_send_xmit: while (ret) { tmp = min_t(int, ret, sg->length - conn->c_xmit_data_off); [tmp = 65536 - 57632 = 7904] conn->c_xmit_data_off += tmp; [c_xmit_data_off = 57632 + 7904 = 65536] ret -= tmp; [ret = 8240 - 7904 = 336] if (conn->c_xmit_data_off == sg->length) { conn->c_xmit_data_off = 0; sg++; conn->c_xmit_sg++; BUG_ON(ret != 0 && conn->c_xmit_sg == rm->data.op_nents); [c_xmit_sg = 1, rm->data.op_nents = 1] What the current fix does: Since the congestion update over loopback is not actually transmitted as a message, all that rds_ib_xmit needs to do is let the caller think the full message has been transmitted and not return partial bytes. It will return 8240 (RDS_CONG_MAP_BYTES+48) when PAGE_SIZE is 4Kb. And 64Kb+48 when page size is 64Kb. Reported-by:
Josh Hunt <joshhunt00@gmail.com> Tested-by:
Honggang Li <honli@redhat.com> Acked-by:
Bang Nguyen <bang.nguyen@oracle.com> Signed-off-by:
Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 28e24c62 ] Few network drivers really supports frag_list : virtual drivers. Some drivers wrongly advertise NETIF_F_FRAGLIST feature. If skb with a frag_list is given to them, packet on the wire will be corrupt. Remove this flag, as core networking stack will make sure to provide packets that can be sent without corruption. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Cc: Anirudha Sarangi <anirudh@xilinx.com> Signed-off-by:
-
- 03 Jan, 2014 35 commits
-
-
Ben Hutchings authored
-
KOBAYASHI Yoshitake authored
commit c8760069 upstream. Current MMC driver doesn't handle generic error (bit19 of device status) in write sequence. As a result, write data gets lost when generic error occurs. For example, a generic error when updating a filesystem management information causes a loss of write data and corrupts the filesystem. In the worst case, the system will never boot. This patch includes the following functionality: 1. To enable error checking for the response of CMD12 and CMD13 in write command sequence 2. To retry write sequence when a generic error occurs Messages are added for v2 to show what occurs. [Backported to 3.4-stable] Signed-off-by:
KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp> Signed-off-by:
Chris Ball <cjb@laptop.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 8a56d776 upstream. Commit 8c4f3c3f "ftrace: Check module functions being traced on reload" fixed module loading and unloading with respect to function tracing, but it missed the function graph tracer. If you perform the following # cd /sys/kernel/debug/tracing # echo function_graph > current_tracer # modprobe nfsd # echo nop > current_tracer You'll get the following oops message: ------------[ cut here ]------------ WARNING: CPU: 2 PID: 2910 at /linux.git/kernel/trace/ftrace.c:1640 __ftrace_hash_rec_update.part.35+0x168/0x1b9() Modules linked in: nfsd exportfs nfs_acl lockd ipt_MASQUERADE sunrpc ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables uinput snd_hda_codec_idt CPU: 2 PID: 2910 Comm: bash Not tainted 3.13.0-rc1-test #7 Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS SDBLI944.86P 05/08/2007 0000000000000668 ffff8800787efcf8 ffffffff814fe193 ffff88007d500000 0000000000000000 ffff8800787efd38 ffffffff8103b80a 0000000000000668 ffffffff810b2b9a ffffffff81a48370 0000000000000001 ffff880037aea000 Call Trace: [<ffffffff814fe193>] dump_stack+0x4f/0x7c [<ffffffff8103b80a>] warn_slowpath_common+0x81/0x9b [<ffffffff810b2b9a>] ? __ftrace_hash_rec_update.part.35+0x168/0x1b9 [<ffffffff8103b83e>] warn_slowpath_null+0x1a/0x1c [<ffffffff810b2b9a>] __ftrace_hash_rec_update.part.35+0x168/0x1b9 [<ffffffff81502f89>] ? __mutex_lock_slowpath+0x364/0x364 [<ffffffff810b2cc2>] ftrace_shutdown+0xd7/0x12b [<ffffffff810b47f0>] unregister_ftrace_graph+0x49/0x78 [<ffffffff810c4b30>] graph_trace_reset+0xe/0x10 [<ffffffff810bf393>] tracing_set_tracer+0xa7/0x26a [<ffffffff810bf5e1>] tracing_set_trace_write+0x8b/0xbd [<ffffffff810c501c>] ? ftrace_return_to_handler+0xb2/0xde [<ffffffff811240a8>] ? __sb_end_write+0x5e/0x5e [<ffffffff81122aed>] vfs_write+0xab/0xf6 [<ffffffff8150a185>] ftrace_graph_caller+0x85/0x85 [<ffffffff81122dbd>] SyS_write+0x59/0x82 [<ffffffff8150a185>] ftrace_graph_caller+0x85/0x85 [<ffffffff8150a2d2>] system_call_fastpath+0x16/0x1b ---[ end trace 940358030751eafb ]--- The above mentioned commit didn't go far enough. Well, it covered the function tracer by adding checks in __register_ftrace_function(). The problem is that the function graph tracer circumvents that (for a slight efficiency gain when function graph trace is running with a function tracer. The gain was not worth this). The problem came with ftrace_startup() which should always be called after __register_ftrace_function(), if you want this bug to be completely fixed. Anyway, this solution moves __register_ftrace_function() inside of ftrace_startup() and removes the need to call them both. Reported-by:
Dave Wysochanski <dwysocha@redhat.com> Fixes: ed926f9b ("ftrace: Use counters to enable functions to trace") Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 8c4f3c3f upstream. There's been a nasty bug that would show up and not give much info. The bug displayed the following warning: WARNING: at kernel/trace/ftrace.c:1529 __ftrace_hash_rec_update+0x1e3/0x230() Pid: 20903, comm: bash Tainted: G O 3.6.11+ #38405.trunk Call Trace: [<ffffffff8103e5ff>] warn_slowpath_common+0x7f/0xc0 [<ffffffff8103e65a>] warn_slowpath_null+0x1a/0x20 [<ffffffff810c2ee3>] __ftrace_hash_rec_update+0x1e3/0x230 [<ffffffff810c4f28>] ftrace_hash_move+0x28/0x1d0 [<ffffffff811401cc>] ? kfree+0x2c/0x110 [<ffffffff810c68ee>] ftrace_regex_release+0x8e/0x150 [<ffffffff81149f1e>] __fput+0xae/0x220 [<ffffffff8114a09e>] ____fput+0xe/0x10 [<ffffffff8105fa22>] task_work_run+0x72/0x90 [<ffffffff810028ec>] do_notify_resume+0x6c/0xc0 [<ffffffff8126596e>] ? trace_hardirqs_on_thunk+0x3a/0x3c [<ffffffff815c0f88>] int_signal+0x12/0x17 ---[ end trace 793179526ee09b2c ]--- It was finally narrowed down to unloading a module that was being traced. It was actually more than that. When functions are being traced, there's a table of all functions that have a ref count of the number of active tracers attached to that function. When a function trace callback is registered to a function, the function's record ref count is incremented. When it is unregistered, the function's record ref count is decremented. If an inconsistency is detected (ref count goes below zero) the above warning is shown and the function tracing is permanently disabled until reboot. The ftrace callback ops holds a hash of functions that it filters on (and/or filters off). If the hash is empty, the default means to filter all functions (for the filter_hash) or to disable no functions (for the notrace_hash). When a module is unloaded, it frees the function records that represent the module functions. These records exist on their own pages, that is function records for one module will not exist on the same page as function records for other modules or even the core kernel. Now when a module unloads, the records that represents its functions are freed. When the module is loaded again, the records are recreated with a default ref count of zero (unless there's a callback that traces all functions, then they will also be traced, and the ref count will be incremented). The problem is that if an ftrace callback hash includes functions of the module being unloaded, those hash entries will not be removed. If the module is reloaded in the same location, the hash entries still point to the functions of the module but the module's ref counts do not reflect that. With the help of Steve and Joern, we found a reproducer: Using uinput module and uinput_release function. cd /sys/kernel/debug/tracing modprobe uinput echo uinput_release > set_ftrace_filter echo function > current_tracer rmmod uinput modprobe uinput # check /proc/modules to see if loaded in same addr, otherwise try again echo nop > current_tracer [BOOM] The above loads the uinput module, which creates a table of functions that can be traced within the module. We add uinput_release to the filter_hash to trace just that function. Enable function tracincg, which increments the ref count of the record associated to uinput_release. Remove uinput, which frees the records including the one that represents uinput_release. Load the uinput module again (and make sure it's at the same address). This recreates the function records all with a ref count of zero, including uinput_release. Disable function tracing, which will decrement the ref count for uinput_release which is now zero because of the module removal and reload, and we have a mismatch (below zero ref count). The solution is to check all currently tracing ftrace callbacks to see if any are tracing any of the module's functions when a module is loaded (it already does that with callbacks that trace all functions). If a callback happens to have a module function being traced, it increments that records ref count and starts tracing that function. There may be a strange side effect with this, where tracing module functions on unload and then reloading a new module may have that new module's functions being traced. This may be something that confuses the user, but it's not a big deal. Another approach is to disable all callback hashes on module unload, but this leaves some ftrace callbacks that may not be registered, but can still have hashes tracing the module's function where ftrace doesn't know about it. That situation can cause the same bug. This solution solves that case too. Another benefit of this solution, is it is possible to trace a module's function on unload and load. Link: http://lkml.kernel.org/r/20130705142629.GA325@redhat.comReported-by:
Jörn Engel <joern@logfs.org> Reported-by:
Dave Jones <davej@redhat.com> Reported-by:
Steve Hodgson <steve@purestorage.com> Tested-by:
-
Steven Rostedt authored
commit 06a51d93 upstream. There are two types of hashes in the ftrace_ops; one type is the filter_hash and the other is the notrace_hash. Either one may be null, meaning it has no elements. But when elements are added, the hash is allocated. Throughout the code, a check needs to be made to see if a hash exists or the hash has elements, but the check if the hash exists is usually missing causing the possible "NULL pointer dereference bug". Add a helper routine called "ftrace_hash_empty()" that returns true if the hash doesn't exist or its count is zero. As they mean the same thing. Last-bug-reported-by:
Jiri Olsa <jolsa@redhat.com> Signed-off-by:
-
Steven Rostedt authored
commit c842e975 upstream. When disabling the "notrace" records, that means we want to trace them. If the notrace_hash is zero, it means that we want to trace all records. But to disable a zero notrace_hash means nothing. The check for the notrace_hash count was incorrect with: if (hash && !hash->count) return With the correct comment above it that states that we do nothing if the notrace_hash has zero count. But !hash also means that the notrace hash has zero count. I think this was done to protect against dereferencing NULL. But if !hash is true, then we go through the following loop without doing a single thing. Fix it to: if (!hash || !hash->count) return; Signed-off-by:
-
Jason Wang authored
commit 6f092343 upstream. We don't validate iph->ihl which may lead a dead loop if we meet a IPIP skb whose iph->ihl is zero. Fix this by failing immediately when iph->ihl is evil (less than 5). This issue were introduced by commit ec5efe79 (rps: support IPIP encapsulation). Cc: Eric Dumazet <edumazet@google.com> Cc: Petr Matousek <pmatouse@redhat.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Daniel Borkmann <dborkman@redhat.com> Signed-off-by:
Jason Wang <jasowang@redhat.com> Acked-by:
-
Dan Carpenter authored
commit 31978b5c upstream. If we allocate less than sizeof(struct attrlist) then we end up corrupting memory or doing a ZERO_PTR_SIZE dereference. This can only be triggered with CAP_SYS_ADMIN. Reported-by:
Nico Golde <nico@ngolde.de> Reported-by:
Fabian Yamaguchi <fabs@goesec.de> Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Dave Chinner <dchinner@redhat.com> Signed-off-by:
Ben Myers <bpm@sgi.com> (cherry picked from commit 071c529e) Signed-off-by:
-
Mahesh Rajashekhara authored
commit b4789b8e upstream. It appears that driver runs into a problem here if fibsize is too small because we allocate user_srbcmd with fibsize size only but later we access it until user_srbcmd->sg.count to copy it over to srbcmd. It is not correct to test (fibsize < sizeof(*user_srbcmd)) because this structure already includes one sg element and this is not needed for commands without data. So, we would recommend to add the following (instead of test for fibsize == 0). Signed-off-by:
Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com> Reported-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Dan Carpenter authored
commit a497e47d upstream. If we do a zero size allocation then it will oops. Also we can't be sure the user passes us a NUL terminated string so I've added a terminator. This code can only be triggered by root. Reported-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Russell King authored
commit 8404663f upstream. The {get,put}_user macros don't perform range checking on the provided __user address when !CPU_HAS_DOMAINS. This patch reworks the out-of-line assembly accessors to check the user address against a specified limit, returning -EFAULT if is is out of range. [will: changed get_user register allocation to match put_user] [rmk: fixed building on older ARM architectures] Reported-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> [bwh: Backported to 3.2: TUSER() was called T()] Signed-off-by:
-
Alex Williamson authored
commit e40f193f upstream. The iommu integration into memory slots expects memory slots to be added or removed and doesn't handle the move case. We can unmap slots from the iommu after we mark them invalid and map them before installing the final memslot array. Also re-order the kmemdup vs map so we don't leave iommu mappings if we get ENOMEM. Reviewed-by:
Gleb Natapov <gleb@redhat.com> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
Marcelo Tosatti <mtosatti@redhat.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Marcelo Tosatti authored
commit 12d6e753 upstream. PPC must flush all translations before the new memory slot is visible. Signed-off-by:
Avi Kivity <avi@redhat.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Neil Horman authored
commit 714b33d1 upstream. Stephan Mueller reported to me recently a error in random number generation in the ansi cprng. If several small requests are made that are less than the instances block size, the remainder for loop code doesn't increment rand_data_valid in the last iteration, meaning that the last bytes in the rand_data buffer gets reused on the subsequent smaller-than-a-block request for random data. The fix is pretty easy, just re-code the for loop to make sure that rand_data_valid gets incremented appropriately Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Reported-by:
Stephan Mueller <stephan.mueller@atsec.com> CC: Stephan Mueller <stephan.mueller@atsec.com> CC: Petr Matousek <pmatouse@redhat.com> CC: Herbert Xu <herbert@gondor.apana.org.au> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Benjamin Tissoires authored
commit 8821f5dc upstream. When working on report indexes, always validate that they are in bounds. Without this, a HID device could report a malicious feature report that could trick the driver into a heap overflow: [ 634.885003] usb 1-1: New USB device found, idVendor=0596, idProduct=0500 ... [ 676.469629] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten Note that we need to change the indexes from s8 to s16 as they can be between -1 and 255. CVE-2013-2897 Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> [bwh: Backported to 3.2: mt_device::{cc,cc_value,inputmode}_index do not exist and the corresponding indices do not need to be validated. mt_device::maxcontact_report_id does not exist either. So all we need to do is to widen mt_device::inputmode.] Signed-off-by:
-
fan.du authored
[ Upstream commit 3868204d ] commit a553e4a6 ("[PKTGEN]: IPSEC support") tried to support IPsec ESP transport transformation for pktgen, but acctually this doesn't work at all for two reasons(The orignal transformed packet has bad IPv4 checksum value, as well as wrong auth value, reported by wireshark) - After transpormation, IPv4 header total length needs update, because encrypted payload's length is NOT same as that of plain text. - After transformation, IPv4 checksum needs re-caculate because of payload has been changed. With this patch, armmed pktgen with below cofiguration, Wireshark is able to decrypted ESP packet generated by pktgen without any IPv4 checksum error or auth value error. pgset "flag IPSEC" pgset "flows 1" Signed-off-by:
Fan Du <fan.du@windriver.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 7f88c6b2 ] IPv6 stats are 64 bits and thus are protected with a seqlock. By not disabling bottom-half we could deadlock here if we don't disable bh and a softirq reentrantly updates the same mib. Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit f1d8cba6 ] In commit c9e90429 ("ipv4: fix possible seqlock deadlock") I left another places where IP_INC_STATS_BH() were improperly used. udp_sendmsg(), ping_v4_sendmsg() and tcp_v4_connect() are called from process context, not from softirq context. This was detected by lockdep seqlock support. Reported-by:
jongman heo <jongman.heo@samsung.com> Fixes: 584bdf8c ("[IPV4]: Fix "ipOutNoRoutes" counter error for TCP and UDP") Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind") Signed-off-by:
-
Veaceslav Falico authored
[ Upstream commit ec6f809f ] Currently we're using plain spin_lock() in prb_shutdown_retire_blk_timer(), however the timer might fire right in the middle and thus try to re-aquire the same spinlock, leaving us in a endless loop. To fix that, use the spin_lock_bh() to block it. Fixes: f6fb8f10 ("af-packet: TPACKET_V3 flexible buffer implementation.") CC: "David S. Miller" <davem@davemloft.net> CC: Daniel Borkmann <dborkman@redhat.com> CC: Willem de Bruijn <willemb@google.com> CC: Phil Sutter <phil@nwl.cc> CC: Eric Dumazet <edumazet@google.com> Reported-by:
Jan Stancek <jstancek@redhat.com> Tested-by:
Veaceslav Falico <vfalico@redhat.com> Acked-by:
Daniel Borkmann <dborkman@redhat.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit e40526cb ] Salam reported a use after free bug in PF_PACKET that occurs when we're sending out frames on a socket bound device and suddenly the net device is being unregistered. It appears that commit 827d9780 introduced a possible race condition between {t,}packet_snd() and packet_notifier(). In the case of a bound socket, packet_notifier() can drop the last reference to the net_device and {t,}packet_snd() might end up suddenly sending a packet over a freed net_device. To avoid reverting 827d9780 and thus introducing a performance regression compared to the current state of things, we decided to hold a cached RCU protected pointer to the net device and maintain it on write side via bind spin_lock protected register_prot_hook() and __unregister_prot_hook() calls. In {t,}packet_snd() path, we access this pointer under rcu_read_lock through packet_cached_dev_get() that holds reference to the device to prevent it from being freed through packet_notifier() while we're in send path. This is okay to do as dev_put()/dev_hold() are per-cpu counters, so this should not be a performance issue. Also, the code simplifies a bit as we don't need need_rls_dev anymore. Fixes: 827d9780 ("af-packet: Use existing netdev reference for bound sockets.") Reported-by:
Salam Noureddine <noureddine@aristanetworks.com> Signed-off-by:
-
Ding Tianhong authored
[ Upstream commit f8730420 ] When the following commands are executed: brctl addbr br0 ifconfig br0 hw ether <addr> rmmod bridge The calltrace will occur: [ 563.312114] device eth1 left promiscuous mode [ 563.312188] br0: port 1(eth1) entered disabled state [ 563.468190] kmem_cache_destroy bridge_fdb_cache: Slab cache still has objects [ 563.468197] CPU: 6 PID: 6982 Comm: rmmod Tainted: G O 3.12.0-0.7-default+ #9 [ 563.468199] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007 [ 563.468200] 0000000000000880 ffff88010f111e98 ffffffff814d1c92 ffff88010f111eb8 [ 563.468204] ffffffff81148efd ffff88010f111eb8 0000000000000000 ffff88010f111ec8 [ 563.468206] ffffffffa062a270 ffff88010f111ed8 ffffffffa063ac76 ffff88010f111f78 [ 563.468209] Call Trace: [ 563.468218] [<ffffffff814d1c92>] dump_stack+0x6a/0x78 [ 563.468234] [<ffffffff81148efd>] kmem_cache_destroy+0xfd/0x100 [ 563.468242] [<ffffffffa062a270>] br_fdb_fini+0x10/0x20 [bridge] [ 563.468247] [<ffffffffa063ac76>] br_deinit+0x4e/0x50 [bridge] [ 563.468254] [<ffffffff810c7dc9>] SyS_delete_module+0x199/0x2b0 [ 563.468259] [<ffffffff814e0922>] system_call_fastpath+0x16/0x1b [ 570.377958] Bridge firewalling registered --------------------------- cut here ------------------------------- The reason is that when the bridge dev's address is changed, the br_fdb_change_mac_address() will add new address in fdb, but when the bridge was removed, the address entry in the fdb did not free, the bridge_fdb_cache still has objects when destroy the cache, Fix this by flushing the bridge address entry when removing the bridge. v2: according to the Toshiaki Makita and Vlad's suggestion, I only delete the vlan0 entry, it still have a leak here if the vlan id is other number, so I need to call fdb_delete_by_port(br, NULL, 1) to flush all entries whose dst is NULL for the bridge. Suggested-by:
Toshiaki Makita <toshiaki.makita1@gmail.com> Suggested-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
Ding Tianhong <dingtianhong@huawei.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit d2615bf4 ] The following commit: b6c40d68 net: only invoke dev->change_rx_flags when device is UP tried to fix a problem with VLAN devices and promiscuouse flag setting. The issue was that VLAN device was setting a flag on an interface that was down, thus resulting in bad promiscuity count. This commit blocked flag propagation to any device that is currently down. A later commit: deede2fa vlan: Don't propagate flag changes on down interfaces fixed VLAN code to only propagate flags when the VLAN interface is up, thus fixing the same issue as above, only localized to VLAN. The problem we have now is that if we have create a complex stack involving multiple software devices like bridges, bonds, and vlans, then it is possible that the flags would not propagate properly to the physical devices. A simple examle of the scenario is the following: eth0----> bond0 ----> bridge0 ---> vlan50 If bond0 or eth0 happen to be down at the time bond0 is added to the bridge, then eth0 will never have promisc mode set which is currently required for operation as part of the bridge. As a result, packets with vlan50 will be dropped by the interface. The only 2 devices that implement the special flag handling are VLAN and DSA and they both have required code to prevent incorrect flag propagation. As a result we can remove the generic solution introduced in b6c40d68 and leave it to the individual devices to decide whether they will block flag propagation or not. Reported-by:
Stefan Priebe <s.priebe@profihost.ag> Suggested-by:
Vlad Yasevich <vyasevic@redhat.com> Signed-off-by:
-
Ying Xue authored
[ Upstream commit b5de4a22 ] init_card() calls dev_get_by_name() to get a network deceive. But it doesn't decrease network device reference count after the device is used. Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 1fa4c710 ] Offenders don't have port numbers, so set it to 0. Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit db31c55a ] If kmsg->msg_namelen > sizeof(struct sockaddr_storage) then in the original code that would lead to memory corruption in the kernel if you had audit configured. If you didn't have audit configured it was harmless. There are some programs such as beta versions of Ruby which use too large of a buffer and returning an error code breaks them. We should clamp the ->msg_namelen value instead. Fixes: 1661bf36 ("net: heap overflow in __audit_sockaddr()") Reported-by:
Eric Wong <normalperson@yhbt.net> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 85fbaa75 ] Commit bceaa902 ("inet: prevent leakage of uninitialized memory to user in recv syscalls") conditionally updated addr_len if the msg_name is written to. The recv_error and rxpmtu functions relied on the recvmsg functions to set up addr_len before. As this does not happen any more we have to pass addr_len to those functions as well and set it to the size of the corresponding sockaddr length. This broke traceroute and such. Fixes: bceaa902 ("inet: prevent leakage of uninitialized memory to user in recv syscalls") Reported-by:
Brad Spengler <spender@grsecurity.net> Reported-by: Tom Labanowski Cc: mpb <mpb.mail@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 68c6beb3 ] In that case it is probable that kernel code overwrote part of the stack. So we should bail out loudly here. The BUG_ON may be removed in future if we are sure all protocols are conformant. Suggested-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit f3d33426 ] This patch now always passes msg->msg_namelen as 0. recvmsg handlers must set msg_namelen to the proper size <= sizeof(struct sockaddr_storage) to return msg_name to the user. This prevents numerous uninitialized memory leaks we had in the recvmsg handlers and makes it harder for new code to accidentally leak uninitialized memory. Optimize for the case recvfrom is called with NULL as address. We don't need to copy the address at all, so set it to NULL before invoking the recvmsg handler. We can do so, because all the recvmsg handlers must cope with the case a plain read() is called on them. read() also sets msg_name to NULL. Also document these changes in include/linux/net.h as suggested by David Miller. Changes since RFC: Set msg->msg_name = NULL if user specified a NULL in msg_name but had a non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't affect sendto as it would bail out earlier while trying to copy-in the address. It also more naturally reflects the logic by the callers of verify_iovec. With this change in place I could remove " if (!uaddr || msg_sys->msg_namelen == 0) msg->msg_name = NULL ". This change does not alter the user visible error logic as we ignore msg_namelen as long as msg_name is NULL. Also remove two unnecessary curly brackets in ___sys_recvmsg and change comments to netdev style. Cc: David Miller <davem@davemloft.net> Suggested-by:
-
Hannes Frederic Sowa authored
[ Upstream commit bceaa902 ] Only update *addr_len when we actually fill in sockaddr, otherwise we can return uninitialized memory from the stack to the caller in the recvfrom, recvmmsg and recvmsg syscalls. Drop the the (addr_len == NULL) checks because we only get called with a valid addr_len pointer either from sock_common_recvmsg or inet_recvmsg. If a blocking read waits on a socket which is concurrently shut down we now return zero and set msg_msgnamelen to 0. Reported-by:
mpb <mpb.mail@gmail.com> Suggested-by:
-
Eric Dumazet authored
[ Upstream commit c9e90429 ] ip4_datagram_connect() being called from process context, it should use IP_INC_STATS() instead of IP_INC_STATS_BH() otherwise we can deadlock on 32bit arches, or get corruptions of SNMP counters. Fixes: 584bdf8c ("[IPV4]: Fix "ipOutNoRoutes" counter error for TCP and UDP") Signed-off-by:
-
Chris Metcalf authored
[ Upstream commit 1ca1a4cf ] In af3e095a, Erik Jacobsen fixed one type of unaligned access bug for ia64 by converting a 64-bit write to use put_unaligned(). Unfortunately, since gcc will convert a short memset() to a series of appropriately-aligned stores, the problem is now visible again on tilegx, where the memset that zeros out proc_event is converted to three 64-bit stores, causing an unaligned access panic. A better fix for the original problem is to ensure that proc_event is aligned to 8 bytes here. We can do that relatively easily by arranging to start the struct cn_msg aligned to 8 bytes and then offset by 4 bytes. Doing so means that the immediately following proc_event structure is then correctly aligned to 8 bytes. The result is that the memset() stores are now aligned, and as an added benefit, we can remove the put_unaligned() calls in the code. Signed-off-by:
Chris Metcalf <cmetcalf@tilera.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit f9a23c84 ] These strings come from a copy_from_user() and there is no way to be sure they are NUL terminated. Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit b869ccfa ] This patch fixes two race conditions between bond_store_updelay/downdelay and bond_store_miimon which could lead to division by zero as miimon can be set to 0 while either updelay/downdelay are being set and thus miss the zero check in the beginning, the zero div happens because updelay/downdelay are stored as new_value / bond->params.miimon. Use rtnl to synchronize with miimon setting. CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Veaceslav Falico <vfalico@redhat.com> Signed-off-by:
Nikolay Aleksandrov <nikolay@redhat.com> Acked-by:
-
Jukka Rissanen authored
[ Upstream commit 1188f054 ] If priority/traffic class field in IPv6 header is set (seen when using ssh), the uncompression sets the TC and Flow fields incorrectly. Example: This is IPv6 header of a sent packet. Note the priority/TC (=1) in the first byte. 00000000: 61 00 00 00 00 2c 06 40 fe 80 00 00 00 00 00 00 00000010: 02 02 72 ff fe c6 42 10 fe 80 00 00 00 00 00 00 00000020: 02 1e ab ff fe 4c 52 57 This gets compressed like this in the sending side 00000000: 72 31 04 06 02 1e ab ff fe 4c 52 57 ec c2 00 16 00000010: aa 2d fe 92 86 4e be c6 .... In the receiving end, the packet gets uncompressed to this IPv6 header 00000000: 60 06 06 02 00 2a 1e 40 fe 80 00 00 00 00 00 00 00000010: 02 02 72 ff fe c6 42 10 fe 80 00 00 00 00 00 00 00000020: ab ff fe 4c 52 57 ec c2 First four bytes are set incorrectly and we have also lost two bytes from destination address. The fix is to switch the case values in switch statement when checking the TC field. Signed-off-by:
Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by:
-
Veaceslav Falico authored
[ Upstream commit ec9f1d15 ] Currently the ARP monitoring is not supported with 802.3ad, and it's prohibited to use it via the module params. However we still can set it afterwards via sysfs, cause we only check for *LB modes there. To fix this - add a check for 802.3ad mode in bonding_store_arp_interval. CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> Signed-off-by:
-
