Introduce rx-queues debugfs node in order to dump rx queues status.
This would be useful for mcu fw debugging
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Make Kconfig entry obvious for MT7663E
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Enable 802.11 power-save support available in mt7663 firmware
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

remove IEEE80211_HW_PS_NULLFUNC_STACK capability from mt76_phy_init
routine since 802.11 ps is not currently supported by any devices and it
will conflict with mt7663 ps fw support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For sta mode mac80211 provides aid in vif->bss_conf.aid.
In order to properly support 802.11 power-save, configure correct aid
to mcu during sta association
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The vendor SDK also disables ASPM by default
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add missing register definitions in order to enable sensitivity tuning
for mt7663 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce support for mt7663u 802.11ac 2x2:2 chipset to mt7615 driver.
Main difference respect to pcie code base is the usb code needs to
configure wtbl from non-atomic context
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Create mt7615-common module in order to collect shared code between usb
and mmio code. Move the following source files in mt7615-common module:
- main.c
- init.c
- mcu.c
- mac.c
- debugfs.c
- eeprom.c
- trace.c

Create the following source files for mmio only source code and move them
in mt7615e module:
- pci_init.c
- dma.c
- pci_mac.c
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

make mac_work per phy instead of per device and fix a possible deadlock
in mt7615_stop since mt7615_mac_work runs holding mt76 mutex

Fixes: fdd2e570 ("mt76: mt7615: add dual-phy support for mac80211 ops")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Sparse report warnings at mt76_tx_status_unlock() and mt76_tx_status_lock()

warning: context imbalance in mt76_tx_status_lock() - wrong count at exit
warning: context imbalance in mt76_tx_status_unlock() - unexpected unlock

The root cause is the additional __acquire(&dev->status_list.lock)
and __release(&dev->status_list.unlock) called
 from inside mt76_tx_status_lock() and mt76_tx_status_unlock().

Remove __acquire(&dev->status_list.lock) annotation
Remove __releases(&dev->status_list.unlock)
Correct &dev->status_list.unlock to &dev->status_list.lock
	-unlock not defined in the sk_buff_head struct
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Enable MSI/MSI-X PCI interrupts by default. This patch has been tested
using Banana Pi r64 board
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

With MSI interrupts, IRQs must not be enabled from within the IRQ handler,
because that can lead to lost events.
Defer IRQ processing to a tasklet, which is also responsible for enabling
IRQs (to avoid race conditions against the handler)
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Soul Huang <soul.huang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix DMA unmap length for mt7663e devices in mt7615_txp_skb_unmap_hw

Fixes: f40ac0f3 ("mt76: mt7615: introduce mt7663e support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Soul Huang <soul.huang@mediatek.com>
Signed-off-by: Soul Huang <soul.huang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>

Fix DMA unmap length estimation in mt7615_txp_skb_unmap_hw for mt7622
chipset

Fixes: 6aa4ed79 ("mt76: mt7615: implement DMA support for MT7622")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>

They do not apply to software scan
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Avoid having to attempt hw scan and fall back to software for every scan
on devices/firmware without hw scan support
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix register definitions for aggr range counter registers for mt7663
chipset

Fixes: f40ac0f3 ("mt76: mt7615: introduce mt7663e support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Check that val is not zero before aggr_per estimation in order to avoid a
possible division by 0
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When the EEPROM data is read from flash, it can contain tx DPD calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When the EEPROM data is read from flash, it can contain DC offset calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

It is used to enable merging of Flash EEPROM data with OTP ROM calibration.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The function “platform_get_irq” can log an error already.
Thus omit a redundant message for the exception handling in the
calling function.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mac80211/hostapd runs mt7615_set_channel with the same channel
parameters sending multiple rdd commands overwriting the previous ones.
This behaviour is causing tpt issues on dfs channels.
Fix the issue checking new channel freq/width with the running one.

Fixes: 5dabdf71 ("mt76: mt7615: add multiple wiphy support to the dfs support code")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Rom patch is shared between Bluetooth and Wifi devices, so correct the
naming to allow two drivers to share the same file.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce address parameter to mt7615_eeprom_init routine in order to be
reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Generalize mt7615_rate_desc introducing mt7615_wtbl_desc and
mt7615_key_desc data structures in order to configure the hw wtbl
in a non-atomic context for usb devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Remove key dependency from mt7615_mac_wtbl_update_key and export
mt7615_mac_wtbl_update_key, mt7615_mac_wtbl_update_pk and
mt7615_mac_wtbl_update_cipher in order to reuse them in usb code.
Move mt7615_mac_get_cipher in mac.h
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Rely on the mt7622 endpoint definitions for mt7663u
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt7615_mac_wtbl_addr in mac.h and add inline qualifier in order to
be reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce __mt7663_load_firmware routine to load firmware for usb
devices.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move register configuration out of mt7615_mac_set_rates since usb
driver can't access device register in interrupt context. Introduce
mt7615_mac_update_rate_desc routine to report rate info to
mt7615_mac_set_rates
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Extend mt7615_write_txwi routine to support usb txwi configuration
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce headroom and tailroom to mt76_mcu_ops data structure in order
to unify the routine used for mcu message allocation. This is a
preliminary patch to add mt7663u support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Remove mt76_wr(dev, MT_CSR(0x010), 0x8208) that would cause
MT_PCIE_IRQ_ENABLE to be disabled; MT_PCIE_IRQ_ENABLE should always keep
on enabled when the driver is running.

0x44064 is a not existing address
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce rlm tlv header in bss_info mcu command in order to
inform the mcu about operating channel. Rlm header is necessary only if
the mcu is running low power functionalities (e.g offloaded scan)
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce BSS absence event that is reported when the fw
is leaving or entering current operational channel.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>