Pull "mvebu DT changes for v3.19 (round 2)" from Jason Cooper:

 - mvebu
    - Use simple-card audio on Armada 370 DB
    - Add DSA node for Armada 370 DB
    - Add SDHCI to Armada 38x
    - Armada 370/XP rework to support new Synology boards
    - Add Synology DS213j and DS414
    - Various pinctrl and uart and alias fixes to help bootloaders

* tag 'mvebu-dt-3.19-2' of git://git.infradead.org/linux-mvebu:
  arm: mvebu: normalize pinctrl entries for Armada SoCs
  arm: mvebu: fix wrongly named DS414 pinctrl entries
  arm: mvebu: add .dts file for Synology DS414
  arm: mvebu: add .dts file for Synology DS213j
  arm: mvebu: define and use common Armada XP SPI pinctrl setting
  arm: mvebu: define and use common Armada XP UART2/3 pinctrl settings
  arm: mvebu: define and use common Armada 370 UART pinctrl settings
  arm: mvebu: define and use common Armada 370 SPI pinctrl settings
  arm: mvebu: move Armada 370/XP pinctrl node definition armada-370-xp.dtsi
  arm: mvebu: use recently introduced uart label for stdout-path
  arm: mvebu: add uartX labels for Armada SoC serial nodes
  arm: mvebu: fix vendor prefix typo in kirkwood-synology.dtsi
  ARM: mvebu: fix ordering in Armada 370 .dtsi
  ARM: mvebu: adjust ethernet aliases according to U-Boot requirements for A38x
  ARM: mvebu: remove clock-frequency from Armada 38x SDHCI Device Tree node
  ARM: mvebu: enable no-1-8-v flag for Armada 385 DB SDHCI interface
  mvebu: 370 RD: Add support for the switch
  ARM: mvebu: use simple-card DT binding for audio on Armada 370 DB
  ARM: mvebu: remove conflicting muxing on Armada 370 DB
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'sirf-dts-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux into next/dt

Pull "change pinmux pingroup and add some lost node/prop" from Barry Song:

1. add resets properity for some nodes;
2. change pinctrl groups for audio
3. add PMU node

* tag 'sirf-dts-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux:
  ARM: dts: atlas6: add resets property for SPI nodes
  ARM: dts: atlas6: add resets property for VPP nodes
  ARM: dts: prima2: add resets property for VPP nodes
  ARM: dts: prima2: add resets property for GPS nodes
  ARM: dts: prima2: add node for Performance Monitor Unit
  ARM: dts: atlas6: Add I2S external clock input pingroup
  ARM: dts: atlas6: add a separate pingroup for i2s mclk output
  ARM: dts: prima2: add I2S 2ch, 6ch, nodin, mclk groups
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'sunxi-simplefb-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt

Pull "Allwinner simple frambuffer support" from Maxime Ripard:

This enables the simple framebuffer on all the supported Allwinner SoCs (but
the A80). That allows to have at last a video display usable by using the
framebuffer the firmware might have set up.

* tag 'sunxi-simplefb-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (55 commits)
  ARM: dts: sunxi: Update simplefb nodes so that u-boot can find them
  ARM: dts: sunxi: Add de_be0 clk parent pll to simplefb node
  ARM: dts: sun7i: Add simplefb node
  ARM: dts: sun6i: Add simplefb node
  ARM: dts: sun5i: Add simplefb node
  ARM: dts: sun4i: Add simplefb node
  ARM: dts: sun6i: Add ethernet support to M9 board
  ARM: sun6i: DT: Add PLL6 multiple outputs
  ARM: dts: sun6i: Add support for the status led
  ARM: dts: sun6i: Add EHCI support for the M9 board
  ARM: dts: sunxi: Add regulator-boot-on property to ahci-5v regulator
  ARM: dts: sun7i: Cubietruck: add power supply regulator for USB OTG VBUS
  ARM: dts: sun7i: Cubietruck: override regulator pin
  ARM: sun7i: dtsi: add support for usbphy0
  ARM: dtsi: sunxi: add common VBUS regulator
  ARM: dts: sunxi: Banana Pi: increase startup-delay for the GMAC PHY regulator
  ARM: sun5i: olinuxino: Relicense the device tree under GPLv2/X11
  ARM: sun4i: cubieboard: Relicense the device tree under GPLv2/X11
  ARM: sun7i: pcduino3: Relicense the device tree under GPLv2/X11
  ARM: sun4i: pcduino: Relicense the device tree under GPLv2/X11
  ...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

Pull "The i.MX device tree changes for 3.19" from Shawn Guo:

 - Device additions for board vf610-colibri, pwm, backlight, I2C, RTC,
   ADC etc.
 - Update i.MX6 phyFLEX board to include PCIe, CAN and audio support
 - Improve SSI clocks description for i.MX5 platforms
 - Add ENET2 support for imx6sx-sdb board
 - Add device tree source for LS1021A SoC, board QDS and TWR
 - Enable cpufreq support for i.MX53
 - Enable VPU device support for i.MX6QDL
 - Enable poweroff support for i.MX6 SoCs
 - Add support for TBS2910 Matrix ARM mini PC which is built on i.MX6Q
 - Create generic base device trees for Vybrid and add support for
   Colibri VF50

Note: the change set is built on top of imx-soc-3.19 to resolve the
dependency that  "ARM: dts: imx53: add cpufreq-dt support" uses the
clock define IMX5_CLK_ARM that is added by "ARM: imx53: clk: add ARM
clock".

* tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (51 commits)
  ARM: dts: imx6q-tbs2910: Enable snvs-poweroff
  ARM: dts: imx6: add pm_power_off support for i.mx6 chips
  ARM: dts: vf-colibri: add USB regulators
  ARM: dts: imx6: phyFLEX: Add CAN support
  ARM: dts: imx6: phyFLEX: Add PCIe
  ARM: dts: imx6: phyFLEX: Set correct interrupt for pmic
  ARM: dts: imx6: phyFLEX: Enable gpmi in module file
  ARM: dts: imx6: phyFLEX: set nodes in alphabetical order
  ARM: dts: vf-colibri-eval-v3.dts: Enable ST-M41T0M6 RTC
  ARM: dts: vf-colibri: Add I2C support
  ARM: dts: imx6qdl: Enable CODA960 VPU
  ARM: dts: imx6q-tbs2910: Remove unneeded 'fsl,mode' property
  ARM: dts: vf610: enable USB misc/phy nodes where necessary
  ARM: dts: vf610: use new GPIO support
  ARM: dts: pbab01: enable I2S audio on phyFLEX-i.MX6 boards
  ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02
  ARM: dts: vf500-colibri: add Colibri VF50 support
  ARM: dts: vf610: create generic base device trees
  ARM: dts: vf610: assign oscillator to clock module
  dt-bindings: arm: add Freescale LS1021A SoC device tree binding
  ...

Signed-off-by; Arnd Bergmann <arnd@arndb.de>

Merge tag 'omap-for-v3.19/dt-part2-updated' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Pull "More dts changes for omaps to add support for new devices" from Tony Lindgren:

- Add DCAN support am335x, am437x and dra7

- Add devices for sb-t3x computers

- Add support for NovaTech OrionLXm

- Add n900 battery and si4713 support

* tag 'omap-for-v3.19/dt-part2-updated' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
  ARM: dts: am335x-evm: Add DCAN1 details
  ARM: dts: am33xx: Update DCAN nodes
  ARM: dts: am33xx: Add control module syscon node
  ARM: dts: am437x-gp: Add dcan support
  ARM: dts: am4372: Add DCAN nodes
  ARM: dts: am4372: Add control module syscon node
  ARM: dts: dra72-evm: Add CAN support
  ARM: dts: dra7-evm: Add CAN support
  ARM: dts: DRA7: Add DCAN nodes
  ARM: dts: dra7: Add syscon regmap for CORE CONTROL area
  ARM: dts: sbc-t3x30: add audio support
  ARM: dts: sbc-t3x: add TV out display alias
  ARM: dts: cm-t3x: add TV out support
  ARM: dts: cm-t3x: add I2C1 pinmux
  ARM: dts: AM43xx: add tscadc DT entries for am437x-evm and am43x-epos-evm
  ARM: dts: cm-t3x30: add keypad support
  ARM: dts: sb-t35: add EEPROM support
  ARM: dts: cm-t3x: add EEPROM support
  ARM: OMAP2+: remove cm-t3x touchscreen pdata quirk
  ARM: dts: cm-t3x: add ADS7846 touchscreen support
  ...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

Pull "Samsung 3rd DT updates for v3.19" from Kukjin Kim:

- exynos3250
  : remove unused bootargs on exynos3250-rinato
  : add new board dt file for exynos3250-monk
- exynos4
  : add missing clock for MFC
  : specify default clocks for camera
- exynos4x12
  : add TMU related DT nodes
- exynos4412-trats2
  : add max77693-haptic and pwm nodes, enable TMU support
- exynos4412-odroid
  : specify audio clock parents and rates
- exynos5250 and exynos5420
  : add syscon based phandle to i2c device nodes
- exynos5250-spring
  : add trackpad, temperature sensor and usb3505 pinctrl

Note: based on previous tags/samsung-dt-2 for v3.19

* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: add sysreg phandle to i2c device nodes for exynos
  ARM: dts: Remove unused bootargs from exynos3250-rinato
  ARM: dts: add board dts file for Exynos3250-based Monk board
  Documentation: devicetree: Add Exynos-based boards compatible string
  ARM: dts: add missing clock to MFC device for exynos4
  ARM: dts: Specify audio clock parents and rates for exynos4412-odroid-common
  ARM: dts: Add trackpad to exynos5250-spring
  ARM: dts: Add temperature sensor to exynos5250-spring
  ARM: dts: Add usb3503 pinctrl to exynos5250-spring
  ARM: dts: Add max77693-haptic node for exynos4412-trats2
  ARM: dts: add pwm node for exynos4412-trats2
  ARM: dts: Specify default clocks for Exynos4 camera devices
  ARM: dts: Enable TMU support for exynos4412-trats2
  ARM: dts: Device tree node definition for TMU on exynos4x12
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

Pull "Samsung 2nd DT updates for v3.19" from Kukjin Kim:

- add micro SD card SDHCI node for exynos4412-trats
- add exynos4415 DT
- add exynos3250-rinato DT and sleep mode support

Note: based on previous tags/samsung-dt for v3.19

* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Add micro SD card SDHCI node for exynos4412-trats
  ARM: dts: Add dts files for exynos4415 SoC
  ARM: dts: Add sleep mode of regulator for exynos3250-rinato
  ARM: dts: Add sleep mode pin configuration for exynos3250-rinato
  ARM: dts: Add board dts file for exynos3250-rinato
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Pull "temporarily disable rk3288-smp" from Heiko Stuebner:

Disable smp again on rk3288 temporarily to make Olof's boottest
run again, until the patches for using the physical architected
timers got accepted.

* tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: temporarily disable smp on rk3288
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This avoids a boot regression

* sunxi/dt:
  Revert "ARM: dts: sunxi: unify APB1 clock"
  Revert "ARM: dts: sunxi: Use sun4i-a10-apb1-clk for sun6i/sun8i apb2 clocks."
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This patch adds syscon based phandle to i2c device nodes of exynos5250
and exynos5420. These phandles will be used to save restore i2c sysreg
configuration register during s2r from i2c driver.

CC: Rob Herring <robh+dt@kernel.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: devicetree@vger.kernel.org
CC: linux-doc@vger.kernel.org
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch removes unused dt node of command line from Exynos3250-based
Rinato board because kernel use the command line from bootloader.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds new board dts file to support Samsung Monk board which
is based on Exynos3250 SoC and has different H/W configuration from
Rinato.

This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
Signed-off-by: Youngjun Cho <yj44.cho@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds the missing compatible/description of Exynos-based
boards to remove following build warning.

WARNING: DT compatible string "samsung,..." appears un-documented --
check ./Documentation/devicetree/bindings/
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

There are currently 2 differents naming conventions used between the
existing Armada SoC DT files for pinctrl entries (*_pin(s): *-pin(s)
and pmx_*: pmx-*) with a vast majority of files using the former:

$ grep _pin arch/arm/boot/dts/armada-*.dts* | wc -l
155
$ grep pmx arch/arm/boot/dts/armada-*.dts* | wc -l
13

In fact, only some Armada XP files are using the second variant.
This patch normalizes those files (mainly ge0/1 entries) to use
the first variant.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/00114c3169e1d93259ff4150ed46ee36eae16b1e.1416670812.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

While renaming pinctrl entries during reviews of Synology DS414 support
series, I missed three entries, as reported by Ben. This patch fixes
those.
Reported-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/608e4fd6e06e9c5289a84b9c38e81b2456dbcd79.1416670812.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

this patch adds missed resets property for CSR SiRFatlasVI SPI nodes.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>

this patch adds missed resets property for CSR SiRFatlasVI Video Post
Processor(VPP) node.
Signed-off-by: Renwei Wu <renwei.wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>

this patch adds missed resets property for CSR SiRFprimaII Video Post
Processor(VPP) node.
Signed-off-by: Renwei Wu <renwei.wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>

this patch adds missed resets property for CSR SiRFprimaII GPS
related nodes.
Signed-off-by: Tao Huang <Tao.Huang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>

It enables Performance Monitor Unit on CSR SiRFprimaII.
Signed-off-by: Ye He <ye.he@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>

The I2S controller can use the external clock as reference clock with
master mode. But based on different hardware or software design, this
external clock might be needed or not needed.
So the external input pin can be an independent pinctrl group, and the
card driver can decice to get it or not.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

The I2S controller can output mclk to external audio codec. But by
hardware design, some codecs need mclk and some codecs do not need
mclk. So the mclk pin can be an independent pinctrl group, and the
card driver can get it or not based on boards.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

we have done that for atlas6 in commit ed36c1a0, 086b8904 etc. here we
do same things for prima2.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

This reverts commit e883d672.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/7h1toxr0ku.fsf@deeprootsystems.com

This reverts commit 338302ae.

This is one of two commits that resulted in a boot regression.

Conflicts:
	arch/arm/boot/dts/sun6i-a31.dtsi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/7h1toxr0ku.fsf@deeprootsystems.com

DCAN1 is routed to CAN port (J11) when Profile 1 is selected on the
profile selection switch.
Provide information for DCAN1 pins and node but keep it disabled
by default. User has to manually enable it if Profile 1 is chosen.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add "raminit-syscon" property to specify the RAMINIT register.
Add clock information.
Rename can nodes from "d_can" to "can" to be compliant
with the ePAPR specs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use syscon regmap to expose the Control module register space.
This register space is shared between many users e.g. DCAN, USB, display, etc.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add DCAN support for AM437x GP EVM with both DCAN instances.

[Roger Q] Updated output pin to not use pull up.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The SoC contains 2 DCAN modules. Add them.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use syscon regmap to expose the Control module register space.
This register space is shared between many users e.g. DCAN, USB, display, etc.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The board has 2 CAN ports but only the first one can be used.
Enable the first CAN port.

WAKEUP0 pin doesn't have INPUT enable bit so we just disable
weak PULLs.

The second CAN port cannot be used without hardware modification
so we don't enable the second port.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The board has 2 CAN ports but only the first one can be used.
Enable the first CAN port.

WAKEUP0 pin doesn't have INPUT enable bit so we just disable
weak PULLs.

The second CAN port cannot be used without hardware modification
so we don't enable the second port.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The SoC supports 2 DCAN nodes. Add them.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Display and DCAN drivers use syscon regmap to access some registers
in the CORE control area. Add the syscon regmap node for this
area.

Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add audio related DT nodes
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add display alias for TV out.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add TV out support.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add missing I2C1 pinmux setup.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Review of the u-boot sunxi simplefb patches has led to the decision that
u-boot should not use a specific path to find the nodes as this goes contrary
to how devicetree usually works.

Instead a platform specific compatible + properties should be used for this.

The simplefb bindings have already been updated to reflect this, this patch
brings the sunxi devicetree files in line with the new binding, and the
actual u-boot implementation as it is going upstream.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>