ret should be signed to notice a failure in wm831x_reg_read().
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This change makes sure all regulator group assignments are cleared on
disable call
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This change implements a basic turnon delay in the regulator enable function
to make it less probable that reg_enable returns before the regulator
output is at target level
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This change ensures the regulator REMAP register configuration is in a known
state so state transitions will function as intended regardless of
possible bootloader effects on it
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This change includes regulator turnon delay values and the REMAP reset
configuration to the twlreg_info struct, since they are basic attributes
of every TWL regulator
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Defines VIO, VDD1, VDD2, VPLL1 and VINT* regulators as always_on by default
since they are critical to TWL and its master's functionality and should
be on in all cases where RegFW is used
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Define all twl4030 regulators in the twlreg_info table, along with
appropriate VSEL tables for adjustable regulators
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

When the mc13783-regulator driver is built in kernel, probing it during
the regulator subsystem initialisation result in a fault.

That is because regulator subsystem is planned to be initialised very early
in the boot process, before the mfd subsystem initialisation.

The mc12783-regulator probing process need to access to the mc13783-core
functionality to read/write mc13783 registers and so must be called after
the mc13783-core driver initialisation.

The way to do this is to let the kernel probe the mc13783-regulator driver when
mc13783-core register his regulator subdevice.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Currently it is possible for regulator_bulk_{enable,disable} operations to
generate unbalanced regulator_{disable,enable} calls in its error path.
In case of an error only those regulators of the bulk operation which actually
had been enabled/disabled should get their original state restored.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

IS_ERR returns only 1 or 0.  The callsite of setup_regulators expects a
negative integer in an error case.  Thus, PTR_ERR has to be used to extract
it.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression E,E1;
@@

*E = IS_ERR(...)
 ... when != E = E1
*return E;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

consumer.h requires device.h for stand alone build.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

- define needed registers and bits in the driver
- properly namespace functions and structs
- fix locking as required by patch
  "mfd/mc13783: near complete rewrite"
- use platform_data as provided by "mfd/mc13783: near complete rewrite"
  instead of accessing struct mc13783
- struct mc13783_regulator_priv.desc is (and was) unused and so can go
  away
- use cpp magic to initialize mc13783_regulators
- bring MODULE_LICENSE in sync with actual copyright
- minor style fixes

This allows not including mc13783-private.h which I intend to remove
soon.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensoruce.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

One annoying thing about the old name was that the module was just
called mc13783 which caused wrong expectations (at least for me).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensoruce.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This patch will remove surplus register writes on shut down of
LDO D (this magic was not needed), remove an unnecessary (!) error
check and really unregister the regulators when the module is
unloaded.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

If selector equals ARRAY_SIZE(da9034_ldo12_data), that is one too
large already.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

If we fall through it means that we hit an unknown regulator/chip
combination so set -ENOENT as an explicit flag (the return code
is only used internally).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

'static const int const' means the same thing as 'static const int'
and sparse complains about this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Since some regulators in the system may not support suspend mode
configuration we need to allow some regulators to have a missing
suspend mode configuration. Do this by requiring that disabled
regulators are explicitly flagged and then skip over regulators
that have no state specified.

Try to avoid surprises by warning the if we could set the state
but no configuration is provided.  This also ensures that an all
zeros configuration generates a warning rather than silently
disabling the regulator.
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Some of the regulator API functions have code to allow the machine
constraints to override the device supplied name for the regulator
in the constraints in order to help tie logging to supplies on the
board and disambiguate when there is more than one regulator chip
in the system. Factor this code out into a new rdev_get_name()
function and use it throughout the regulator API so that we always
use the same name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

When voltage or current constraints are either missing or specify
a range display the actual setting along with the constraints if
we can. This can aid debugging of configuration problems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

It makes sense to do all the voltage configuration in the one split
out function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This allows constraints to take effect on regulators that support
voltage setting but for which the board does not specify a voltage
range (for example, because it is fixed correctly at system startup).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

If we're going to log an error we may as well log what the error
code that we're failing on is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Hi Liam,

Since Samuel merged a new version of mfd 88pm8607 driver, I format a
new patch on regulator 88pm8607. I paste the new patch in mail. Please
help to review again. And I also attach the mfd driver in mail.

From: Haojian Zhuang <haojian.zhuang@marvell.com>
Date: Thu, 8 Oct 2009 09:36:53 -0400
Subject: [PATCH] regulator: Add 88PM8607 PMIC driver

This patch adds regulator drivers for Marvell 88PM8607 PMIC.
This controller contains 3 DVC and 14 LDO regulators. This controller
uses I2C interface.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The BuckWise DC-DC convertors in WM831x devices support switching to
a second output voltage using the logic level on one of the device
pins. This is intended to allow rapid voltage switching for uses like
cpufreq, replacing the I2C or SPI write used to configure the voltage
of the regulator with a much faster GPIO status change.

This is implemented by keeping the DVS voltage configured as the
maximum voltage permitted for the regulator. If a request is made
for the maximum voltage then the GPIO is used to switch to the DVS
voltage, otherwise the normal ON voltage is updated and used. This
follows the idiom used by most cpufreq drivers, which drop the
minimum voltage as the core frequency is dropped but use a constant
maximum - raising the voltage should normally be fast, but lowering
it may be slower.

Configuration of the DVS MFP on the device should be done externally,
for example via OTP.

Support is present in the hardware for monitoring the status of the
transition using a second GPIO. This is not currently implemented
but platform data is provided for it - the driver currently assumes
that the device will be configured to transition immediately - but
platform data is provided to reduce merge issues once it is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Tested with a MX25-based custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Replacing
	error = 0;
	if (error)
		op
with nothing is not quite an equivalent transformation ;-)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  XFS: Free buffer pages array unconditionally
  xfs: kill xfs_bmbt_rec_32/64 types
  xfs: improve metadata I/O merging in the elevator
  xfs: check for not fully initialized inodes in xfs_ireclaim

Commit 3d1e4631 ("get rid of init_file()") removed the export of
alloc_file() -- possibly inadvertently, since that commit mainly
consisted of deleting the lines between the end of alloc_file() and
the start of the code in init_file().

There is in fact one modular use of alloc_file() in the tree, in
drivers/infiniband/core/uverbs_main.c, so re-add the export to fix:

    ERROR: "alloc_file" [drivers/infiniband/core/ib_uverbs.ko] undefined!

when CONFIG_INFINIBAND_USER_ACCESS=m.

Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'next' of git://git.secretlab.ca/git/linux-2.6: (23 commits)
  powerpc: fix up for mmu_mapin_ram api change
  powerpc: wii: allow ioremap within the memory hole
  powerpc: allow ioremap within reserved memory regions
  wii: use both mem1 and mem2 as ram
  wii: bootwrapper: add fixup to calc useable mem2
  powerpc: gamecube/wii: early debugging using usbgecko
  powerpc: reserve fixmap entries for early debug
  powerpc: wii: default config
  powerpc: wii: platform support
  powerpc: wii: hollywood interrupt controller support
  powerpc: broadway processor support
  powerpc: wii: bootwrapper bits
  powerpc: wii: device tree
  powerpc: gamecube: default config
  powerpc: gamecube: platform support
  powerpc: gamecube/wii: flipper interrupt controller support
  powerpc: gamecube/wii: udbg support for usbgecko
  powerpc: gamecube/wii: do not include PCI support
  powerpc: gamecube/wii: declare as non-coherent platforms
  powerpc: gamecube/wii: introduce GAMECUBE_COMMON
  ...

Fix up conflicts in arch/powerpc/mm/fsl_booke_mmu.c.

Hopefully even close to correctly.

* 'drm-vmware-staging' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/vmwgfx: Add DRM driver for VMware Virtual GPU
  drm/vmwgfx: Add svga headers for vmwgfx driver
  drm/ttm: Add more driver type enums

* 'hwpoison' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-mce-2.6: (34 commits)
  HWPOISON: Remove stray phrase in a comment
  HWPOISON: Try to allocate migration page on the same node
  HWPOISON: Don't do early filtering if filter is disabled
  HWPOISON: Add a madvise() injector for soft page offlining
  HWPOISON: Add soft page offline support
  HWPOISON: Undefine short-hand macros after use to avoid namespace conflict
  HWPOISON: Use new shake_page in memory_failure
  HWPOISON: Use correct name for MADV_HWPOISON in documentation
  HWPOISON: mention HWPoison in Kconfig entry
  HWPOISON: Use get_user_page_fast in hwpoison madvise
  HWPOISON: add an interface to switch off/on all the page filters
  HWPOISON: add memory cgroup filter
  memcg: add accessor to mem_cgroup.css
  memcg: rename and export try_get_mem_cgroup_from_page()
  HWPOISON: add page flags filter
  mm: export stable page flags
  HWPOISON: limit hwpoison injector to known page types
  HWPOISON: add fs/device filters
  HWPOISON: return 0 to indicate success reliably
  HWPOISON: make semantics of IGNORED/DELAYED clear
  ...

As predicted during code review, the sysctl(2) changes made systems with
old glibc nearly unusable.  About every command gives a:

  warning: process `ls' used the deprecated sysctl system call with 1.4

warning in the log.

I see this on a SUSE 10.0 system with glibc 2.3.5.

Don't warn for this common case.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (117 commits)
  ACPI processor: Fix section mismatch for processor_add()
  ACPI: Add platform-wide _OSC support.
  ACPI: cleanup pci_root _OSC code.
  ACPI: Add a generic API for _OSC -v2
  msi-wmi: depend on backlight and fix corner-cases problems
  msi-wmi: switch to using input sparse keymap library
  msi-wmi: replace one-condition switch-case with if statement
  msi-wmi: remove unused field 'instance' in key_entry structure
  msi-wmi: remove custom runtime debug implementation
  msi-wmi: rework init
  msi-wmi: remove useless includes
  X86 drivers: Introduce msi-wmi driver
  Toshiba Bluetooth Enabling driver (RFKill handler v3)
  ACPI: fix for lapic_timer_propagate_broadcast()
  acpi_pad: squish warning
  ACPI: dock: minor whitespace and style cleanups
  ACPI: dock: add struct dock_station * directly to platform device data
  ACPI: dock: dock_add - hoist up platform_device_register_simple()
  ACPI: dock: remove global 'dock_device_name'
  ACPI: dock: combine add|alloc_dock_dependent_device (v2)
  ...

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (52 commits)
  perf record: Use per-task-per-cpu events for inherited events
  perf record: Properly synchronize child creation
  perf events: Allow per-task-per-cpu counters
  perf diff: Percent calcs should use double values
  perf diff: Change the default sort order to "dso,symbol"
  perf diff: Use perf_session__fprintf_hists just like 'perf record'
  perf report: Fix cut'n'paste error recently introduced
  perf session: Move perf report specific hits out of perf_session__fprintf_hists
  perf tools: Move hist entries printing routines from perf report
  perf report: Generalize perf_session__fprintf_hists()
  perf symbols: Move symbol filtering to event__preprocess_sample()
  perf symbols: Adopt the strlists for dso, comm
  perf symbols: Make symbol_conf global
  perf probe: Fix to show which probe point is not found
  perf probe: Check symbols in symtab/kallsyms
  perf probe: Check build-id of vmlinux
  perf probe: Reject second attempt of adding same-name event
  perf probe: Support event name for --add option
  perf probe: Add glob matching support on --del
  perf probe: Use strlist__for_each macros in probe-event.c
  ...

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (38 commits)
  direct I/O fallback sync simplification
  ocfs: stop using do_sync_mapping_range
  cleanup blockdev_direct_IO locking
  make generic_acl slightly more generic
  sanitize xattr handler prototypes
  libfs: move EXPORT_SYMBOL for d_alloc_name
  vfs: force reval of target when following LAST_BIND symlinks (try #7)
  ima: limit imbalance msg
  Untangling ima mess, part 3: kill dead code in ima
  Untangling ima mess, part 2: deal with counters
  Untangling ima mess, part 1: alloc_file()
  O_TRUNC open shouldn't fail after file truncation
  ima: call ima_inode_free ima_inode_free
  IMA: clean up the IMA counts updating code
  ima: only insert at inode creation time
  ima: valid return code from ima_inode_alloc
  fs: move get_empty_filp() deffinition to internal.h
  Sanitize exec_permission_lite()
  Kill cached_lookup() and real_lookup()
  Kill path_lookup_open()
  ...

Trivial conflicts in fs/direct-io.c

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM: rwsem.h need not be included into main.c
  PM: Remove unnecessary goto from device_resume_noirq()
  PM: Add initcall_debug style timing for suspend/resume
  PM: allow for usage_count > 0 in pm_runtime_get()

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Fix kprobes build with non-gawk awk
  x86: Split swiotlb initialization into two stages
  x86: Regex support and known-movable symbols for relocs, fix _end
  x86, msr: Remove incorrect, duplicated code in the MSR driver
  x86: Merge kernel_thread()
  x86: Sync 32/64-bit kernel_thread
  x86, 32-bit: Use same regs as 64-bit for kernel_thread_helper
  x86, 64-bit: Use user_mode() to determine new stack pointer in copy_thread()
  x86, 64-bit: Move kernel_thread to C
  x86-64, paravirt: Call set_iopl_mask() on 64 bits
  x86-32: Avoid pipeline serialization in PTREGSCALL1 and 2
  x86: Merge sys_clone
  x86, 32-bit: Convert sys_vm86 & sys_vm86old
  x86: Merge sys_sigaltstack
  x86: Merge sys_execve
  x86: Merge sys_iopl
  x86-32: Add new pt_regs stubs
  cpumask: Use modern cpumask style in arch/x86/kernel/cpu/mcheck/mce-inject.c

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tracing: Fix return of trace_dump_stack()
  ksym_tracer: Fix bad cast
  tracing/power: Remove two exports
  tracing: Change event->profile_count to be int type
  tracing: Simplify trace_option_write()
  tracing: Remove useless trace option
  tracing: Use seq file for trace_clock
  tracing: Use seq file for trace_options
  function-graph: Allow writing the same val to set_graph_function
  ftrace: Call trace_parser_clear() properly
  ftrace: Return EINVAL when writing invalid val to set_ftrace_filter
  tracing: Move a printk out of ftrace_raw_reg_event_foo()
  tracing: Pull up calls to trace_define_common_fields()
  tracing: Extract duplicate ftrace_raw_init_event_foo()
  ftrace.h: Use common pr_info fmt string
  tracing: Add stack trace to irqsoff tracer
  tracing: Add trace_dump_stack()
  ring-buffer: Move resize integrity check under reader lock
  ring-buffer: Use sync sched protection on ring buffer resizing
  tracing: Fix wrong usage of strstrip in trace_ksyms