The Kconfig currently controlling compilation of this code is:

arch/mips/lantiq/Kconfig:config XRX200_PHY_FW
arch/mips/lantiq/Kconfig:       bool "XRX200 PHY firmware loader"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

We don't replace module.h with init.h since the file doesn't need that.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13932/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The Makefile entry controlling compilation of this code is:

arch/mips/lantiq/xway/vmmc.o
   ---> arch/mips/lantiq/xway/Makefile:obj-y += vmmc.o

...meaning that it currently is not being built as a module by anyone.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We replace module.h with export.h since the file does actually use
EXPORT_SYMBOL.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13930/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The Makefile entry controlling compilation of this code is "obj-y"
meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

We don't replace module.h with init.h since the file already has that.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13931/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The Makefile entry controlling compilation of this code is "obj-y"
meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: "Rafał Miłecki" <zajec5@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13933/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Commit 7eb8c99d ("MIPS: Delete smp-gic.c") removed the file from the
Makefile and the option to build it from KConfig, but left the file
itself floating in the tree.

Remove the unused source file.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: paul.burton@imgtec.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13883/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

According to commit 9f6b6877
("android: remove timed output/gpio driver")
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13904/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The field "owner" is set by the core.
Thus delete an unneeded initialisation.

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Cc: John Crispin <john@phrozen.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: kernel-janitors@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13929/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The addition of VPE information to /proc/cpuinfo used to be in smp-mt.c.
This file is not used by MIPS r6 kernels, so the Virtual Processor
information was not present for these CPU types.

Move the code to print VPE information into proc.c, add a case for MIPS
r6 CPUS, and remove the block from smp-mt.c.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13847/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Yang Ling <gnaygnil@gmail.com>
Cc: keguang.zhang@gmail.com
Cc: chenhc@lemote.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13305/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Adds basic platform devices for Loongson1C, including serial port
and ethernet.
Signed-off-by: Yang Ling <gnaygnil@gmail.com>
Cc: keguang.zhang@gmail.com
Cc: chenhc@lemote.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13304/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Loongson1C is a 32-bit SoC designed by Loongson Technology Co., Ltd,
with many features similar to Loongson1B.
Signed-off-by: Yang Ling <gnaygnil@gmail.com>
Cc: paul.burton@imgtec.com
Cc: markos.chandras@imgtec.com
Cc: james.hogan@imgtec.com
Cc: kumba@gentoo.org
Cc: macro@imgtec.com
Cc: david.daney@cavium.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13303/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Rename upper case variables.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: Sivasubramanian Palanisamy <sivasubramanian.palanisamy@nokia.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13352/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Take all memory into use by default, instead of limiting to 512 MB.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: Sivasubramanian Palanisamy <sivasubramanian.palanisamy@nokia.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13353/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This adds a device tree example for SFR NeufBox 6.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13844/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

BCM6362 is a BMIPS4350 SoC which needs the same fixup as BCM6368 in order to
enable SMP support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13845/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This adds a device tree example for Netgear CVG834G.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13843/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

BCM3368 has a shared TLB which conflicts with current SMP support, so it must
be disabled for now.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13840/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This adds a device tree example for Comtrend VR-3032u, which
also serves as a real example for brcm,bcm6328-leds.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13842/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The prefix bcm9* should only be used for reference and evaluation boards from
Broadcom.
Also adds missing console output to bootargs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13841/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Commit 380e4270 added support for bcm97435svmb.dtb but missed adding it to
DT_NONE.
Also refactor DT_NONE dtbs in order to add larger names in the future.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: john@phrozen.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13839/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Only one defconfig has a STACKPROTECTOR value.  And it asks for
the strong variant, which isn't supported by older toolchains.

Due to the nature of MIPS having more platform specific code than say
x86, the allyesconfig and allmodconfig aren't as effective for build
coverage.  So, in addition, I like to use a trivial script to walk all
the defconfigs and build each one.

However I will get false positives on unsupported stackprotector values
with an older toolchain like gcc-4.6.3.  As in this instance I am just
using the compiler as a glorified syntax checker on a machine where I
build a bunch of other arch for the same reason, there is no real
motivation to get a newer toolchain for improved optimization etc.

Since there is only one of them, and there is nothing about these
settings that are board/platform specific, I propose we just eliminate
the existing instance and take the default.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: James Hartley <james.hartley@imgtec.com>
Cc: Ionela Voinescu <ionela.voinescu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13846/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Pull ARM fixes from Russell King:
 "Three relatively small fixes for ARM:

   - Roger noticed that dma_max_pfn() was calculating the upper limit
     wrongly, by adding the PFN offset of memory twice.

   - A fix from Robin to correct parsing of MPIDR values when the
     address size is larger than one BE32 unit.

   - A fix from Srinivas to ensure that we do not rely on the boot
     loader (or previous Linux kernel) setting the translation table
     base register a certain way in the decompressor, which can lead to
     crashes"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
  ARM: 8617/1: dma: fix dma_max_pfn()
  ARM: 8616/1: dt: Respect property size when parsing CPUs

If the bootloader uses the long descriptor format and jumps to
kernel decompressor code, TTBCR may not be in a right state.
Before enabling the MMU, it is required to clear the TTBCR.PD0
field to use TTBR0 for translation table walks.

The commit dbece458 ("ARM: 7501/1: decompressor:
reset ttbcr for VMSA ARMv7 cores") does the reset of TTBCR.N, but
doesn't consider all the bits for the size of TTBCR.N.

Clear TTBCR.PD0 field and reset all the three bits of TTBCR.N to
indicate the use of TTBR0 and the correct base address width.

Fixes: dbece458 ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull x86 fixes from Thomas Gleixner:
 "The last regression fixes for 4.8 final:

   - Two patches addressing the fallout of the CR4 optimizations which
     caused CR4-less machines to fail.

   - Fix the VDSO build on big endian machines

   - Take care of FPU initialization if no CPUID is available otherwise
     task struct size ends up being zero

   - Fix up context tracking in case load_gs_index fails"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/entry/64: Fix context tracking state warning when load_gs_index fails
  x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUID
  x86/vdso: Fix building on big endian host
  x86/boot: Fix another __read_cr4() case on 486
  x86/init: Fix cr4_init_shadow() on CR4-less machines

Pull MIPS fixes from Ralf Baechle:
 "Another round of fixes:

   - CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems
   - CPS: Avoid BUG() when offlining pre-r6 CPUs
   - DEC: Avoid gas warnings due to suspicious instruction scheduling by
     manually expanding assembler macros.
   - FTLB: Fix configuration by moving confiuguratoin after probing
   - FTLB: clear execution hazard after changing FTLB enable
   - Highmem: Fix detection of unsupported highmem with cache aliases
   - I6400: Don't touch FTLBP chicken bits
   - microMIPS: Fix BUILD_ROLLBACK_PROLOGUE
   - Malta: Fix IOCU disable switch read for MIPS64
   - Octeon: Fix probing of devices attached to GPIO lines
   - uprobes: Misc small fixes"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems
  MIPS: Fix detection of unsupported highmem with cache aliases
  MIPS: Malta: Fix IOCU disable switch read for MIPS64
  MIPS: Fix BUILD_ROLLBACK_PROLOGUE for microMIPS
  MIPS: clear execution hazard after changing FTLB enable
  MIPS: Configure FTLB after probing TLB sizes from config4
  MIPS: Stop setting I6400 FTLBP
  MIPS: DEC: Avoid la pseudo-instruction in delay slots
  MIPS: Octeon: mark GPIO controller node not populated after IRQ init.
  MIPS: uprobes: fix use of uninitialised variable
  MIPS: uprobes: remove incorrect set_orig_insn
  MIPS: fix uretprobe implementation
  MIPS: smp-cps: Avoid BUG() when offlining pre-r6 CPUs

Pull sparc fixes from David Miller:

 1) Fix section mismatches in some builds, from Paul Gortmaker.

 2) Need to count huge zero page mappings when doing TSB sizing, from
    Mike Kravetz.

 3) Fix handing of cpu_possible_mask when nr_cpus module option is
    specified, from Atish Patra.

 4) Don't allocate irq stacks until nr_irqs has been processed, also
    from Atish Patra.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix non-SMP build.
  sparc64: Fix irq stack bootmem allocation.
  sparc64: Fix cpu_possible_mask if nr_cpus is set
  sparc64 mm: Fix more TSB sizing issues
  sparc64: fix section mismatch in find_numa_latencies_for_group

Pull networking fixes from David Miller:

 1) Fix wrong TCP checksums on MTU probing when checksum offloading is
    disabled, from Douglas Caetano dos Santos.

 2) Fix qdisc backlog updates in qfq and sfb schedulers, from Cong Wang.

 3) Route lookup flow key protocol value is wrong in ip6gre_xmit_other(),
    fix from Lance Richardson.

 4) Scheduling while atomic in multicast routing code of ipv4 and ipv6,
    fix from Nikolay Aleksandrov.

 5) Fix packet alignment in fec driver, from Eric Nelson.

 6) Fix perf regression in sctp due to struct layout and cache misses,
    from Xin Long.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock
  sctp: change to check peer prsctp_capable when using prsctp polices
  sctp: remove prsctp_param from sctp_chunk
  sctp: move sent_count to the memory hole in sctp_chunk
  tg3: Avoid NULL pointer dereference in tg3_io_error_detected()
  act_ife: Fix false encoding
  act_ife: Fix external mac header on encode
  VSOCK: Don't dec ack backlog twice for rejected connections
  Revert "net: ethernet: bcmgenet: use phydev from struct net_device"
  net: fec: align IP header in hardware
  net: fec: remove QUIRK_HAS_RACC from i.mx27
  net: fec: remove QUIRK_HAS_RACC from i.mx25
  ipmr, ip6mr: fix scheduling while atomic and a deadlock with ipmr_get_route
  ip6_gre: fix flowi6_proto value in ip6gre_xmit_other()
  tcp: fix a compile error in DBGUNDO()
  tcp: fix wrong checksum calculation on MTU probing
  sch_sfb: keep backlog updated with qlen
  sch_qfq: keep backlog updated with qlen
  can: dev: fix deadlock reported after bus-off

When discovering the number of VPEs per core, smp_num_siblings will be
incorrect for kernels built without support for the MIPS MultiThreading
(MT) ASE running on systems which implement said ASE. This leads to
accesses to VPEs in secondary cores being performed incorrectly since
mips_cm_vp_id calculates the wrong ID to write to the local "other"
registers. Fix this by examining the number of VPEs in the core as
reported by the CM.

This patch presumes that the number of VPEs will be the same in each
core of the system. As this path only applies to systems with CM version
2.5 or lower, and this property is true of all such known systems, this
is likely to be fine but is described in a comment for good measure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14338/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Pull SCSI fix from James Bottomley:
 "One final fix before 4.8.

  There was a memory leak triggered by turning scsi mq off due to the
  fact that we assume on host release that the already running hosts
  weren't mq based because that's the state of the global flag (even
  though they were).

  Fix it by tracking this on a per host host basis"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: Avoid that toggling use_blk_mq triggers a memory leak

Pull input fix from Dmitry Torokhov:
 "One small change to make joydev (which is used by older games) to bind
  to devices that export Z axis but not X or Y (such as TRC rudder)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: joydev - recognize devices with Z axis as joysticks

Merge more fixes from Andrew Morton:
 "Three fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  include/linux/property.h: fix typo/compile error
  ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock()
  mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()

This fixes commit d76eebfa ("include/linux/property.h: fix build
issues with gcc-4.4.4").

With that commit we get the following compile error when using the
PROPERTY_ENTRY_INTEGER_ARRAY macro.

 include/linux/property.h:201:39: error: `u32_data' undeclared (first
                 use in this function)
  PROPERTY_ENTRY_INTEGER_ARRAY(_name_, u32, _val_)
                                       ^
 include/linux/property.h:193:17: note: in definition of macro
                 `PROPERTY_ENTRY_INTEGER_ARRAY'
  { .pointer = { _type_##_data = _val_ } },  \
                 ^

This needs a '.' to reference the union member.  It seems this was just
overlooked here since it is done correctly in similar constructs in
other parts of the original commit.

This fix is in preparation of upcoming commits that will use this macro.

Fixes: commit d76eebfa ("include/linux/property.h: fix build issues with gcc-4.4.4")
Link: http://lkml.kernel.org/r/2de3b929290d88a723ed829a3e3cbd02044714df.1475114627.git.johnyoun@synopsys.comSigned-off-by: John Youn <johnyoun@synopsys.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The testcase "mmaptruncate" of ocfs2-test deadlocks occasionally.

In this testcase, we create a 2*CLUSTER_SIZE file and mmap() on it;
there are 2 process repeatedly performing the following operations
respectively: one is doing memset(mmaped_addr + 2*CLUSTER_SIZE - 1, 'a',
1), while the another is playing ftruncate(fd, 2*CLUSTER_SIZE) and then
ftruncate(fd, CLUSTER_SIZE) again and again.

This is the backtrace when the deadlock happens:

   __wait_on_bit_lock+0x50/0xa0
   __lock_page+0xb7/0xc0
   ocfs2_write_begin_nolock+0x163f/0x1790 [ocfs2]
   ocfs2_page_mkwrite+0x1c7/0x2a0 [ocfs2]
   do_page_mkwrite+0x66/0xc0
   handle_mm_fault+0x685/0x1350
   __do_page_fault+0x1d8/0x4d0
   trace_do_page_fault+0x37/0xf0
   do_async_page_fault+0x19/0x70
   async_page_fault+0x28/0x30

In ocfs2_write_begin_nolock(), we first grab the pages and then allocate
disk space for this write; ocfs2_try_to_free_truncate_log() will be
called if -ENOSPC is returned; if we're lucky to get enough clusters,
which is usually the case, we start over again.

But in ocfs2_free_write_ctxt() the target page isn't unlocked, so we
will deadlock when trying to grab the target page again.

Also, -ENOMEM might be returned in ocfs2_grab_pages_for_write().
Another deadlock will happen in __do_page_mkwrite() if
ocfs2_page_mkwrite() returns non-VM_FAULT_LOCKED, and along with a
locked target page.

These two errors fail on the same path, so fix them by unlocking the
target page manually before ocfs2_free_write_ctxt().

Jan Kara helps me clear out the JBD2 part, and suggest the hint for root
cause.

Changes since v1:
1. Also put ENOMEM error case into consideration.

Link: http://lkml.kernel.org/r/1474173902-32075-1-git-send-email-zren@suse.comSigned-off-by: Eric Ren <zren@suse.com>
Reviewed-by: He Gang <ghe@suse.com>
Acked-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Antonio reports the following crash when using fuse under memory pressure:

  kernel BUG at /build/linux-a2WvEb/linux-4.4.0/mm/workingset.c:346!
  invalid opcode: 0000 [#1] SMP
  Modules linked in: all of them
  CPU: 2 PID: 63 Comm: kswapd0 Not tainted 4.4.0-36-generic #55-Ubuntu
  Hardware name: System manufacturer System Product Name/P8H67-M PRO, BIOS 3904 04/27/2013
  task: ffff88040cae6040 ti: ffff880407488000 task.ti: ffff880407488000
  RIP: shadow_lru_isolate+0x181/0x190
  Call Trace:
    __list_lru_walk_one.isra.3+0x8f/0x130
    list_lru_walk_one+0x23/0x30
    scan_shadow_nodes+0x34/0x50
    shrink_slab.part.40+0x1ed/0x3d0
    shrink_zone+0x2ca/0x2e0
    kswapd+0x51e/0x990
    kthread+0xd8/0xf0
    ret_from_fork+0x3f/0x70

which corresponds to the following sanity check in the shadow node
tracking:

  BUG_ON(node->count & RADIX_TREE_COUNT_MASK);

The workingset code tracks radix tree nodes that exclusively contain
shadow entries of evicted pages in them, and this (somewhat obscure)
line checks whether there are real pages left that would interfere with
reclaim of the radix tree node under memory pressure.

While discussing ways how fuse might sneak pages into the radix tree
past the workingset code, Miklos pointed to replace_page_cache_page(),
and indeed there is a problem there: it properly accounts for the old
page being removed - __delete_from_page_cache() does that - but then
does a raw raw radix_tree_insert(), not accounting for the replacement
page.  Eventually the page count bits in node->count underflow while
leaving the node incorrectly linked to the shadow node LRU.

To address this, make sure replace_page_cache_page() uses the tracked
page insertion code, page_cache_tree_insert().  This fixes the page
accounting and makes sure page-containing nodes are properly unlinked
from the shadow node LRU again.

Also, make the sanity checks a bit less obscure by using the helpers for
checking the number of pages and shadows in a radix tree node.

Fixes: 449dd698 ("mm: keep page cache radix tree nodes in check")
Link: http://lkml.kernel.org/r/20160919155822.29498-1-hannes@cmpxchg.orgSigned-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Antonio SJ Musumeci <trapexit@spawn.link>
Debugged-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@vger.kernel.org>	[3.15+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Change my email address to my kernel.org account instead of the ARM one.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This warning:

 WARNING: CPU: 0 PID: 3331 at arch/x86/entry/common.c:45 enter_from_user_mode+0x32/0x50
 CPU: 0 PID: 3331 Comm: ldt_gdt_64 Not tainted 4.8.0-rc7+ #13
 Call Trace:
  dump_stack+0x99/0xd0
  __warn+0xd1/0xf0
  warn_slowpath_null+0x1d/0x20
  enter_from_user_mode+0x32/0x50
  error_entry+0x6d/0xc0
  ? general_protection+0x12/0x30
  ? native_load_gs_index+0xd/0x20
  ? do_set_thread_area+0x19c/0x1f0
  SyS_set_thread_area+0x24/0x30
  do_int80_syscall_32+0x7c/0x220
  entry_INT80_compat+0x38/0x50

... can be reproduced by running the GS testcase of the ldt_gdt test unit in
the x86 selftests.

do_int80_syscall_32() will call enter_form_user_mode() to convert context
tracking state from user state to kernel state. The load_gs_index() call
can fail with user gsbase, gsbase will be fixed up and proceed if this
happen.

However, enter_from_user_mode() will be called again in the fixed up path
though it is context tracking kernel state currently.

This patch fixes it by just fixing up gsbase and telling lockdep that IRQs
are off once load_gs_index() failed with user gsbase.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1475197266-3440-1-git-send-email-wanpeng.li@hotmail.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Otherwise arch_task_struct_size == 0 and we die.  While we're at it,
set X86_FEATURE_ALWAYS, too.
Reported-by: David Saggiorato <david@saggiorato.net>
Tested-by: David Saggiorato <david@saggiorato.net>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: aaeb5c01c5b ("x86/fpu, sched: Introduce CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT and use it on x86")
Link: http://lkml.kernel.org/r/8de723afbf0811071185039f9088733188b606c9.1475103911.git.luto@kernel.orgSigned-off-by: Ingo Molnar <mingo@kernel.org>

We need to call GET_LE to read hdr->e_type.

Fixes: 57f90c3d ("x86/vdso: Error out if the vDSO isn't a valid DSO")
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-next@vger.kernel.org
Link: http://lkml.kernel.org/r/20160929193442.GA16617@gate.crashing.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

The condition for reading CR4 was wrong: there are some CPUs with
CPUID but not CR4.  Rather than trying to make the condition exact,
use __read_cr4_safe().

Fixes: 18bc7bd5 ("x86/boot: Synchronize trampoline_cr4_features and mmu_cr4_features directly")
Reported-by: david@saggiorato.net
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Link: http://lkml.kernel.org/r/8c453a61c4f44ab6ff43c29780ba04835234d2e5.1475178369.git.luto@kernel.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>