When TDLS QoS is supported by the the peer and the local card, add
the WMM parameter IE to the setup-confirm frame. Take the QoS settings
from the current AP, or if unsupported, use the default values from
the specification. This behavior is mandated by IEEE802.11-2012 section
10.22.4.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If QoS is supported by the card, add an appropriate IE to TDLS setup-
request and setup-response frames.

Consolidate the setting of the WMM info IE across mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When sending setup-failure frames, set the capability field to zero, as
mandated by the specification (IEEE802.11-2012 8.5.13).
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Most setup-specific information elements are not to be added when a
setup frame is sent with an error status code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When building TDLS setup frames, use the IE order mandates in the
specification, splitting extra IEs coming from usermode.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add all information elements for TDLS discovery and setup in the same
function.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The patch "8f02e6b mac80211: make sure TDLS peer STA exists during
setup" broke TDLS error paths where the STA doesn't exist when sending
the error.
Fix it by only testing for STA existence during a non-error flow.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Infer the TDLS initiator and track it in mac80211 via a STA flag. This
avoids breaking old userspace that doesn't pass it via nl80211 APIs.

The only case where userspace will need to pass the initiator is when the
STA is removed due to unreachability before a teardown packet is sent.
Support for unreachability was only recently added to wpa_supplicant, so
it won't be a problem in practice.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When lockdep isn't compiled, a local variable isn't used
(it's only in a macro argument), annotate it to suppress
the compiler warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Driver is now responsible for veryfing if the
switch is possible.

Since this is inherently tricky driver may decide
to disconnect an interface later with
cfg80211_stop_iface().

This doesn't mean driver can accept everything. It
should do it's best to verify requests and reject
them as soon as possible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Channel switch finalization is now 2-step. First
step is when driver calls chswitch_done(), the
other is when reservation is actually finalized
(which be defered for in-place reservation).

It is now safe to call ieee80211_chswitch_done()
more than once.

Also remove the ieee80211_vif_change_channel()
because it is no longer used.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Channel switch finalization is now 2-step. First
step is when driver calls csa_finish(), the other
is when reservation is actually finalized (which
can be deferred for in-place reservation).

It is now safe to call ieee80211_csa_finish() more
than once.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The ieee80211_check_combinations() computes
radar_detect accordingly depending on chanctx
reservation status.

This makes it possible to use the function for
channel_switch validation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Multi-vif in-place reservations happen when
it is impossible to allocate more channel contexts
as indicated by interface combinations.

Such reservations are not finalized until all
assigned interfaces are ready.

This still doesn't handle all possible cases
(i.e. degradation of number of channels) properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Split sched scan IEs to band specific and not band specific
blocks. Common IEs blocks may be sent to the FW once per command,
instead of per band.

This allows optimization of size of the command, which may be
required by some drivers (eg. iwlmvm with newer firmware version).

As this changes the mac80211 API, update all drivers to use the
new version correctly, even if they don't (yet) make use of the
split data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.

As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

After sending a TDLS discovery-request, we expect a reply to arrive on
the AP's channel. We must stay on the channel (no PSM, scan, etc.), since
a TDLS setup-response is a direct packet not buffered by the AP.
Add a new mac80211 driver callback to allow discovery session protection.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Make sure userspace added a TDLS peer station before invoking the
transmission of the first setup frame. This ensures packets to the peer
won't go through the AP path.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Write a mac80211 to the cfg80211 API for requesting a userspace TDLS
operation. Define TDLS specific reason codes that can be used here.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

As the spec mandates, flush data in the AP path before transmitting the
first setup frame. Data packets transmitted during setup are already
dropped in the Tx path.

For the teardown flow, flush all packets in the direct path before
transmitting the teardown frame. Un-authorize the peer sta after teardown
is sent, forcing all subsequent Tx to the peer through the AP.

Make sure to flush the queues when disabling the link to get the
teardown packet out.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
[adjust to Luca's new quuee API and stop only vif queues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There are setup/teardown specific actions to be done that accompany
the sending of a TDLS management packet. Split the main function to
simplify future additions.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Use the value from userspace in order to have a correct teardown packet.
With the current code, a teardown from the responder side fails the TDLS
MIC check because of a bad link identifier IE.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.

Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When setting up a TDLS session, register a delayed work to remove
the peer if setup times out. Prevent concurrent setups to support this
capacity.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For TDLS, the AUTHORIZED flag arrives with all other important station
info (supported rates, HT/VHT caps, ...). Make sure to set the station
state in the low-level driver after transferring this information to
the mac80211 STA entry.
This aligns the STA information during sta_state callbacks with the
non-TDLS case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Rename the flags used in the Tx path and add an explanation for the
reasons to drop, send directly or through the AP.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of stopping all the hardware queues during channel switch,
which is especially bad when we have large CSA counts, stop only the
queues that are assigned to the vif that is performing the channel
switch.

Additionally, check for (sdata->csa_block_tx) instead of calling
ieee80211_csa_needs_block_tx(), which can now be removed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In some cases we may want to stop the queues of a single vif (for
instance during a channel-switch).  Add a function that stops all the
queues that are assigned to a vif.  If a queue is assigned to more
than one vif, the corresponding netdev subqueue of the other vif(s)
will also be stopped.  If the HW doesn't set the
IEEE80211_HW_QUEUE_CONTROL flag, then all queues are stopped.

Also add a corresponding function to wake the queues of a vif back.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Sometimes different vifs may be stopping the queues for the same
reason (e.g. when several interfaces are performing a channel switch).
Instead of using a bitmask for the reasons, use an integer that holds
a refcount instead.  In order to keep it backwards compatible,
introduce a boolean in some functions that tell us whether the queue
stopping should be refcounted or not.  For now, use not refcounted for
all calls to keep it functionally the same as before.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There is no need to stop all queues when we want to flush specific
queues, so stop only the queues that will be flushed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Converting time from one format to another seems to give coders a warm
and fuzzy feeling.

Use the proper interfaces.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John W. Linville <linville@tuxdriver.com>
[fix compile error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Using perm_addr is always wrong, it may be reassigned by
anyone using standard netdev APIs. Remove that from the
match function and also use the match function where only
the perm_addr was used now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

do_posix_clock_monotonic_gettime() is a leftover from the initial
posix timer implementation which maps to ktime_get_ts().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

vif->csa_active is protected by mutexes only. This
means it is unreliable to depend on it on codeflow
in non-sleepable beacon and CSA code. There was no
guarantee to have vif->csa_active update be
visible before beacons are updated on SMP systems.

Using csa counter offsets which are embedded in
beacon struct (and thus are protected with single
RCU assignment) is much safer.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Having csa counters part of beacon and probe_resp
structures makes it easier to get rid of possible
races between setting a beacon and updating
counters on SMP systems by guaranteeing counters
are always consistent against given beacon struct.

While at it relax WARN_ON into WARN_ON_ONCE to
prevent spamming logs and racing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[remove pointless array check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Allow send frames using monitor interface
when DFS chandef and we pass CAC (beaconing
allowed).

This fix problem when old kernel and new backports used,
in such case hostapd create/use also monitor interface.
Before this patch all frames hostapd send using monitor
iface were dropped when AP was configured on DFS channel.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.

To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since WEP is practically dead, there seems very little
point in keeping WEP weak IV accounting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The mesh_plink code is doing some interesting things with the
ignore_plink_timer flag.  It seems the original intent was to
handle this race:

cpu 0                           cpu 1
-----                           -----
                                start timer handler for state X
acquire sta_lock
change state from X to Y
mod_timer() / del_timer()
release sta_lock
                                acquire sta_lock
                                execute state Y timer too soon

However, using the mod_timer()/del_timer() return values to
detect these cases is broken.  As a result, timers get ignored
unnecessarily, and stations can get stuck in the peering state
machine.

Instead, we can detect the case by looking at the timer expiration.
In the case of del_timer, just ignore the timers in the following
(LISTEN/ESTAB) states since they won't have timers anyway.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>