- 26 Mar, 2021 3 commits
-
-
Chunfeng Yun authored
The MediaTek 0.96 xHCI controller on some platforms does not support bulk stream even HCCPARAMS says supporting, due to MaxPSASize is set a default value 1 by mistake, here use XHCI_BROKEN_STREAMS quirk to fix it. Fixes: 94a631d9 ("usb: xhci-mtk: check hcc_params after adding primary hcd") Cc: stable <stable@vger.kernel.org> Signed-off-by:
Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/1616482975-17841-4-git-send-email-chunfeng.yun@mediatek.comSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Wesley Cheng authored
Ensure that dep->flags are cleared until after stop active transfers is completed. Otherwise, the ENDXFER command will not be executed during ep disable. Fixes: f09ddcfc ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers") Cc: stable <stable@vger.kernel.org> Reported-and-tested-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Wesley Cheng <wcheng@codeaurora.org> Link: https://lore.kernel.org/r/1616610664-16495-1-git-send-email-wcheng@codeaurora.orgSigned-off-by:
-
Shuah Khan authored
Fix shift out-of-bounds in vhci_hub_control() SetPortFeature handling. UBSAN: shift-out-of-bounds in drivers/usb/usbip/vhci_hcd.c:605:42 shift exponent 768 is too large for 32-bit type 'int' Reported-by: syzbot+3dea30b047f41084de66@syzkaller.appspotmail.com Cc: stable@vger.kernel.org Signed-off-by:
Shuah Khan <skhan@linuxfoundation.org> Link: https://lore.kernel.org/r/20210324230654.34798-1-skhan@linuxfoundation.orgSigned-off-by:
-
- 23 Mar, 2021 17 commits
-
-
Vincent Palatin authored
This LTE modem (M.2 card) has a bug in its power management: there is some kind of race condition for U3 wake-up between the host and the device. The modem firmware sometimes crashes/locks when both events happen at the same time and the modem fully drops off the USB bus (and sometimes re-enumerates, sometimes just gets stuck until the next reboot). Tested with the modem wired to the XHCI controller on an AMD 3015Ce platform. Without the patch, the modem dropped of the USB bus 5 times in 3 days. With the quirk, it stayed connected for a week while the 'runtime_suspended_time' counter incremented as excepted. Signed-off-by:
Vincent Palatin <vpalatin@chromium.org> Link: https://lore.kernel.org/r/20210319124802.2315195-1-vpalatin@chromium.org Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
Do not log the successful-probe message until the tty device has been registered. Signed-off-by:
Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210322155318.9837-9-johan@kernel.orgSigned-off-by:
-
Johan Hovold authored
Make sure to always claim the data interface and bail out if binding fails. Note that the driver had a check to verify that the data interface was not already bound to a driver but would not detect other failures (e.g. if the interface was not authorised). Signed-off-by:
-
Johan Hovold authored
Use negation consistently throughout the driver for NULL checks. Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Johan Hovold authored
Name the probe error labels after what they do rather than using sequence numbers which is harder to review and maintain (e.g. may require renaming unrelated labels when a label is added or removed). Acked-by:
-
Johan Hovold authored
There's no need to clear the interface driver data on failed probe (and driver core will clear it anyway). Acked-by:
-
Johan Hovold authored
The interface driver data has already been set by usb_driver_claim_interface() so drop the redundant subsequent assignment. Acked-by:
-
Johan Hovold authored
If tty-device registration fails the driver would fail to release the data interface. When the device is later disconnected, the disconnect callback would still be called for the data interface and would go about releasing already freed resources. Fixes: c93d8195 ("usb: cdc-acm: fix error handling in acm_probe()") Cc: stable@vger.kernel.org # 3.9 Cc: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by:
-
Johan Hovold authored
If tty-device registration fails the driver copy of any Country Selection functional descriptor would end up being freed twice; first explicitly in the error path and then again in the tty-port destructor. Drop the first erroneous free that was left when fixing a tty-port resource leak. Fixes: cae2bc76 ("usb: cdc-acm: Decrement tty port's refcount if probe() fail") Cc: stable@vger.kernel.org # 4.19 Cc: Jaejoong Kim <climbbb.kim@gmail.com> Acked-by:
-
Oliver Neukum authored
This failure is so common that logging an error here amounts to spamming log files. Reviewed-by:
Bruno Thomsen <bruno.thomsen@gmail.com> Signed-off-by:
-
Oliver Neukum authored
We have a cycle of callbacks scheduling works which submit URBs with thos callbacks. This needs to be blocked, stopped and unblocked to untangle the circle. The issue leads to faults like: [ 55.068392] Unable to handle kernel paging request at virtual address 6b6b6c03 [ 55.075624] pgd = be866494 [ 55.078335] [6b6b6c03] *pgd=00000000 [ 55.081924] Internal error: Oops: 5 [#1] PREEMPT SMP ARM [ 55.087238] Modules linked in: ppp_async crc_ccitt ppp_generic slhc xt_TCPMSS xt_tcpmss xt_hl nf_log_ipv6 nf_log_ipv4 nf_log_common xt_policy xt_limit xt_conntrack xt_tcpudp xt_pkttype ip6table_mangle iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_mangle ip6table_filter ip6_tables iptable_filter ip_tables des_generic md5 sch_fq_codel cdc_mbim cdc_wdm cdc_ncm usbnet mii cdc_acm usb_storage ip_tunnel xfrm_user xfrm6_tunnel tunnel6 xfrm4_tunnel tunnel4 esp6 esp4 ah6 ah4 xfrm_algo xt_LOG xt_LED xt_comment x_tables ipv6 [ 55.134954] CPU: 0 PID: 82 Comm: kworker/0:2 Tainted: G T 5.8.17 #1 [ 55.142526] Hardware name: Freescale i.MX7 Dual (Device Tree) [ 55.148304] Workqueue: events acm_softint [cdc_acm] [ 55.153196] PC is at kobject_get+0x10/0xa4 [ 55.157302] LR is at usb_get_dev+0x14/0x1c [ 55.161402] pc : [<8047c06c>] lr : [<80560448>] psr: 20000193 [ 55.167671] sp : bca39ea8 ip : 00007374 fp : bf6cbd80 [ 55.172899] r10: 00000000 r9 : bdd92284 r8 : bdd92008 [ 55.178128] r7 : 6b6b6b6b r6 : fffffffe r5 : 60000113 r4 : 6b6b6be3 [ 55.184658] r3 : 6b6b6b6b r2 : 00000111 r1 : 00000000 r0 : 6b6b6be3 [ 55.191191] Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none [ 55.198417] Control: 10c5387d Table: bcf0c06a DAC: 00000051 [ 55.204168] Process kworker/0:2 (pid: 82, stack limit = 0x9bdd2a89) [ 55.210439] Stack: (0xbca39ea8 to 0xbca3a000) [ 55.214805] 9ea0: bf6cbd80 80769a50 6b6b6b6b 80560448 bdeb0500 8056bfe8 [ 55.222991] 9ec0: 00000002 b76da000 00000000 bdeb0500 bdd92448 bca38000 bdeb0510 8056d69c [ 55.231177] 9ee0: bca38000 00000000 80c050fc 00000000 bca39f44 09d42015 00000000 00000001 [ 55.239363] 9f00: bdd92448 bdd92438 bdd92000 7f1158c4 bdd92448 bca2ee00 bf6cbd80 bf6cef00 [ 55.247549] 9f20: 00000000 00000000 00000000 801412d8 bf6cbd98 80c03d00 bca2ee00 bf6cbd80 [ 55.255735] 9f40: bca2ee14 bf6cbd98 80c03d00 00000008 bca38000 80141568 00000000 80c446ae [ 55.263921] 9f60: 00000000 bc9ed880 bc9f0700 bca38000 bc117eb4 80141524 bca2ee00 bc9ed8a4 [ 55.272107] 9f80: 00000000 80147cc8 00000000 bc9f0700 80147b84 00000000 00000000 00000000 [ 55.280292] 9fa0: 00000000 00000000 00000000 80100148 00000000 00000000 00000000 00000000 [ 55.288477] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 55.296662] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [ 55.304860] [<8047c06c>] (kobject_get) from [<80560448>] (usb_get_dev+0x14/0x1c) [ 55.312271] [<80560448>] (usb_get_dev) from [<8056bfe8>] (usb_hcd_unlink_urb+0x50/0xd8) [ 55.320286] [<8056bfe8>] (usb_hcd_unlink_urb) from [<8056d69c>] (usb_kill_urb.part.0+0x44/0xd0) [ 55.329004] [<8056d69c>] (usb_kill_urb.part.0) from [<7f1158c4>] (acm_softint+0x4c/0x10c [cdc_acm]) [ 55.338082] [<7f1158c4>] (acm_softint [cdc_acm]) from [<801412d8>] (process_one_work+0x19c/0x3e8) [ 55.346969] [<801412d8>] (process_one_work) from [<80141568>] (worker_thread+0x44/0x4dc) [ 55.355072] [<80141568>] (worker_thread) from [<80147cc8>] (kthread+0x144/0x180) [ 55.362481] [<80147cc8>] (kthread) from [<80100148>] (ret_from_fork+0x14/0x2c) [ 55.369706] Exception stack(0xbca39fb0 to 0xbca39ff8) Tested-by:
-
Oliver Neukum authored
Counting break events is nice but we should actually report them to the tty layer. Fixes: 5a6a62bd ("cdc-acm: add TIOCMIWAIT") Signed-off-by:
-
Tong Zhang authored
init_dma_pools() calls dma_pool_create(...dev->dev) to create dma pool. however, dev->dev is actually set after calling init_dma_pools(), which effectively makes dma_pool_create(..NULL) and cause crash. To fix this issue, init dma only after dev->dev is set. [ 1.317993] RIP: 0010:dma_pool_create+0x83/0x290 [ 1.323257] Call Trace: [ 1.323390] ? pci_write_config_word+0x27/0x30 [ 1.323626] init_dma_pools+0x41/0x1a0 [snps_udc_core] [ 1.323899] udc_pci_probe+0x202/0x2b1 [amd5536udc_pci] Fixes: 7c51247a (usb: gadget: udc: Provide correct arguments for 'dma_pool_create') Cc: stable <stable@vger.kernel.org> Signed-off-by:
Tong Zhang <ztong0001@gmail.com> Link: https://lore.kernel.org/r/20210317230400.357756-1-ztong0001@gmail.comSigned-off-by:
-
Andy Shevchenko authored
It seems that on Intel Merrifield platform the USB PHY shouldn't be suspended. Otherwise it can't be enabled by simply change the cable in the connector. Enable corresponding quirk for the platform in question. Fixes: e5f4ca3f ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression") Suggested-by:
Serge Semin <fancer.lancer@gmail.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210322125244.79407-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Thinh Nguyen authored
If the gadget driver doesn't specify a max_speed, then use the controller's maximum supported speed as default. For DWC_usb32 IP, the gadget's speed maybe limited to gen2x1 rate only if the driver's max_speed is unknown. This scenario should not occur with the current implementation since the default gadget driver's max_speed should always be specified. However, to make the driver more robust and help with readability, let's cover all the scenarios in __dwc3_gadget_set_speed(). Fixes: 450b9e9f ("usb: dwc3: gadget: Set speed only up to the max supported") Cc: <stable@vger.kernel.org> Signed-off-by:
Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/55ac7001af73bfe9bc750c6446ef4ac8cf6f9313.1615254129.git.Thinh.Nguyen@synopsys.comSigned-off-by:
-
Thinh Nguyen authored
Set the dwc->gadget_max_speed to SuperSpeed Plus if the user sets the ssp_rate. The udc_set_ssp_rate() is intended for setting the gadget's speed to SuperSpeed Plus at the specified rate. Fixes: 072cab8a ("usb: dwc3: gadget: Implement setting of SSP rate") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Shawn Guo authored
The ACPI probe starts failing since commit bea46b98 ("usb: dwc3: qcom: Add interconnect support in dwc3 driver"), because there is no interconnect support for ACPI, and of_icc_get() call in dwc3_qcom_interconnect_init() will just return -EINVAL. Fix the problem by skipping interconnect init for ACPI probe, and then the NULL icc_path_ddr will simply just scheild all ICC calls. Fixes: bea46b98 ("usb: dwc3: qcom: Add interconnect support in dwc3 driver") Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210311060318.25418-1-shawn.guo@linaro.orgSigned-off-by:
-
- 21 Mar, 2021 20 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 fixes from Ted Ts'o: "Miscellaneous ext4 bug fixes for v5.12" * tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: initialize ret to suppress smatch warning ext4: stop inode update before return ext4: fix rename whiteout with fast commit ext4: fix timer use-after-free on failed mount ext4: fix potential error in ext4_do_update_inode ext4: do not try to set xattr into ea_inode if value is empty ext4: do not iput inode under running transaction in ext4_rename() ext4: find old entry again if failed to rename whiteout ext4: fix error handling in ext4_end_enable_verity() ext4: fix bh ref count on error paths fs/ext4: fix integer overflow in s_log_groups_per_flex ext4: add reclaim checks to xattr code ext4: shrink race window in ext4_should_retry_alloc()
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull io_uring followup fixes from Jens Axboe: - The SIGSTOP change from Eric, so we properly ignore that for PF_IO_WORKER threads. - Disallow sending signals to PF_IO_WORKER threads in general, we're not interested in having them funnel back to the io_uring owning task. - Stable fix from Stefan, ensuring we properly break links for short send/sendmsg recv/recvmsg if MSG_WAITALL is set. - Catch and loop when needing to run task_work before a PF_IO_WORKER threads goes to sleep. * tag 'io_uring-5.12-2021-03-21' of git://git.kernel.dk/linux-block: io_uring: call req_set_fail_links() on short send[msg]()/recv[msg]() with MSG_WAITALL io-wq: ensure task is running before processing task_work signal: don't allow STOP on PF_IO_WORKER threads signal: don't allow sending any signals to PF_IO_WORKER threads
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/stagingLinus Torvalds authored
Pull staging and IIO driver fixes from Greg KH: "Some small staging and IIO driver fixes: - MAINTAINERS changes for the move of the staging mailing list - comedi driver fixes to get request_irq() to work correctly - counter driver fixes for reported issues with iio devices - tiny iio driver fixes for reported issues. All of these have been in linux-next with no reported problems" * tag 'staging-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: vt665x: fix alignment constraints staging: comedi: cb_pcidas64: fix request_irq() warn staging: comedi: cb_pcidas: fix request_irq() warn MAINTAINERS: move the staging subsystem to lists.linux.dev MAINTAINERS: move some real subsystems off of the staging mailing list iio: gyro: mpu3050: Fix error handling in mpu3050_trigger_handler iio: hid-sensor-temperature: Fix issues of timestamp channel iio: hid-sensor-humidity: Fix alignment issue of timestamp channel counter: stm32-timer-cnt: fix ceiling miss-alignment with reload register counter: stm32-timer-cnt: fix ceiling write max value counter: stm32-timer-cnt: Report count function when SLAVE_MODE_DISABLED iio: adc: ab8500-gpadc: Fix off by 10 to 3 iio:adc:stm32-adc: Add HAS_IOMEM dependency iio: adis16400: Fix an error code in adis16400_initial_setup() iio: adc: adi-axi-adc: add proper Kconfig dependencies iio: adc: ad7949: fix wrong ADC result due to incorrect bit mask iio: hid-sensor-prox: Fix scale not correct issue iio:adc:qcom-spmi-vadc: add default scale to LR_MUX2_BAT_ID channel
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usbLinus Torvalds authored
Pull USB and Thunderbolt driver fixes from Greg KH: "Here are some small Thunderbolt and USB driver fixes for some reported issues: - thunderbolt fixes for minor problems - typec fixes for power issues - usb-storage quirk addition - usbip bugfix - dwc3 bugfix when stopping transfers - cdnsp bugfix for isoc transfers - gadget use-after-free fix All have been in linux-next this week with no reported issues" * tag 'usb-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: usb: typec: tcpm: Skip sink_cap query only when VDM sm is busy usb: dwc3: gadget: Prevent EP queuing while stopping transfers usb: typec: tcpm: Invoke power_supply_changed for tcpm-source-psy- usb: typec: Remove vdo[3] part of tps6598x_rx_identity_reg struct usb-storage: Add quirk to defeat Kindle's automatic unload usb: gadget: configfs: Fix KASAN use-after-free usbip: Fix incorrect double assignment to udc->ud.tcp_rx usb: cdnsp: Fixes incorrect value in ISOC TRB thunderbolt: Increase runtime PM reference count on DP tunnel discovery thunderbolt: Initialize HopID IDAs in tb_switch_alloc()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fix from Ingo Molnar: "A change to robustify force-threaded IRQ handlers to always disable interrupts, plus a DocBook fix. The force-threaded IRQ handler change has been accelerated from the normal schedule of such a change to keep the bad pattern/workaround of spin_lock_irqsave() in handlers or IRQF_NOTHREAD as a kludge from spreading" * tag 'irq-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq: Disable interrupts for force threaded handlers genirq/irq_sim: Fix typos in kernel doc (fnode -> fwnode)
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Ingo Molnar: "Boundary condition fixes for bugs unearthed by the perf fuzzer" * tag 'perf-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/x86/intel: Fix unchecked MSR access error caused by VLBR_EVENT perf/x86/intel: Fix a crash caused by zero PEBS status
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull locking fixes from Ingo Molnar: - Get static calls & modules right. Hopefully. - WW mutex fixes * tag 'locking-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: static_call: Fix static_call_update() sanity check static_call: Align static_call_is_init() patching condition static_call: Fix static_call_set_init() locking/ww_mutex: Fix acquire/release imbalance in ww_acquire_init()/ww_acquire_fini() locking/ww_mutex: Simplify use_ww_ctx & ww_ctx handling
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull EFI fixes from Ingo Molnar: - another missing RT_PROP table related fix, to ensure that the efivarfs pseudo filesystem fails gracefully if variable services are unsupported - use the correct alignment for literal EFI GUIDs - fix a use after unmap issue in the memreserve code * tag 'efi-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: efi: use 32-bit alignment for efi_guid_t literals firmware/efi: Fix a use after bug in efi_mem_reserve_persistent efivars: respect EFI_UNSUPPORTED return from firmware
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Borislav Petkov: "The freshest pile of shiny x86 fixes for 5.12: - Add the arch-specific mapping between physical and logical CPUs to fix devicetree-node lookups - Restore the IRQ2 ignore logic - Fix get_nr_restart_syscall() to return the correct restart syscall number. Split in a 4-patches set to avoid kABI breakage when backporting to dead kernels" * tag 'x86_urgent_for_v5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/apic/of: Fix CPU devicetree-node lookups x86/ioapic: Ignore IRQ2 again x86: Introduce restart_block->arch_data to remove TS_COMPAT_RESTART x86: Introduce TS_COMPAT_RESTART to fix get_nr_restart_syscall() x86: Move TS_COMPAT back to asm/thread_info.h kernel, fs: Introduce and use set_restart_fn() and arch_set_restart_data() -
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Michael Ellerman: - Fix a possible stack corruption and subsequent DLPAR failure in the rpadlpar_io PCI hotplug driver - Two build fixes for uncommon configurations Thanks to Christophe Leroy and Tyrel Datwyler. * tag 'powerpc-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: PCI: rpadlpar: Fix potential drc_name corruption in store functions powerpc: Force inlining of cpu_has_feature() to avoid build failure powerpc/vdso32: Add missing _restgpr_31_x to fix build failure
-
Stefan Metzmacher authored
Without that it's not safe to use them in a linked combination with others. Now combinations like IORING_OP_SENDMSG followed by IORING_OP_SPLICE should be possible. We already handle short reads and writes for the following opcodes: - IORING_OP_READV - IORING_OP_READ_FIXED - IORING_OP_READ - IORING_OP_WRITEV - IORING_OP_WRITE_FIXED - IORING_OP_WRITE - IORING_OP_SPLICE - IORING_OP_TEE Now we have it for these as well: - IORING_OP_SENDMSG - IORING_OP_SEND - IORING_OP_RECVMSG - IORING_OP_RECV For IORING_OP_RECVMSG we also check for the MSG_TRUNC and MSG_CTRUNC flags in order to call req_set_fail_links(). There might be applications arround depending on the behavior that even short send[msg]()/recv[msg]() retuns continue an IOSQE_IO_LINK chain. It's very unlikely that such applications pass in MSG_WAITALL, which is only defined in 'man 2 recvmsg', but not in 'man 2 sendmsg'. It's expected that the low level sock_sendmsg() call just ignores MSG_WAITALL, as MSG_ZEROCOPY is also ignored without explicitly set SO_ZEROCOPY. We also expect the caller to know about the implicit truncation to MAX_RW_COUNT, which we don't detect. cc: netdev@vger.kernel.org Link: https://lore.kernel.org/r/c4e1a4cc0d905314f4d5dc567e65a7b09621aab3.1615908477.git.metze@samba.orgSigned-off-by:
Stefan Metzmacher <metze@samba.org> Signed-off-by:
Jens Axboe <axboe@kernel.dk>
-
Jens Axboe authored
Mark the current task as running if we need to run task_work from the io-wq threads as part of work handling. If that is the case, then return as such so that the caller can appropriately loop back and reset if it was part of a going-to-sleep flush. Fixes: 3bfe6106 ("io-wq: fork worker threads from original task") Signed-off-by:
-
Eric W. Biederman authored
Just like we don't allow normal signals to IO threads, don't deliver a STOP to a task that has PF_IO_WORKER set. The IO threads don't take signals in general, and have no means of flushing out a stop either. Longer term, we may want to look into allowing stop of these threads, as it relates to eg process freezing. For now, this prevents a spin issue if a SIGSTOP is delivered to the parent task. Reported-by:
"Eric W. Biederman" <ebiederm@xmission.com>
-
Jens Axboe authored
They don't take signals individually, and even if they share signals with the parent task, don't allow them to be delivered through the worker thread. Linux does allow this kind of behavior for regular threads, but it's really a compatability thing that we need not care about for the IO threads. Reported-by:
-
Theodore Ts'o authored
Signed-off-by:Theodore Ts'o <tytso@mit.edu>
-
Pan Bian authored
The inode update should be stopped before returing the error code. Signed-off-by:
Pan Bian <bianpan2016@163.com> Link: https://lore.kernel.org/r/20210117085732.93788-1-bianpan2016@163.com Fixes: 8016e29f ("ext4: fast commit recovery path") Cc: stable@kernel.org Reviewed-by:
Harshad Shirwadkar <harshadshirwadkar@gmail.com> Signed-off-by:
-
Harshad Shirwadkar authored
This patch adds rename whiteout support in fast commits. Note that the whiteout object that gets created is actually char device. Which imples, the function ext4_inode_journal_mode(struct inode *inode) would return "JOURNAL_DATA" for this inode. This has a consequence in fast commit code that it will make creation of the whiteout object a fast-commit ineligible behavior and thus will fall back to full commits. With this patch, this can be observed by running fast commits with rename whiteout and seeing the stats generated by ext4_fc_stats tracepoint as follows: ext4_fc_stats: dev 254:32 fc ineligible reasons: XATTR:0, CROSS_RENAME:0, JOURNAL_FLAG_CHANGE:0, NO_MEM:0, SWAP_BOOT:0, RESIZE:0, RENAME_DIR:0, FALLOC_RANGE:0, INODE_JOURNAL_DATA:16; num_commits:6, ineligible: 6, numblks: 3 So in short, this patch guarantees that in case of rename whiteout, we fall back to full commits. Amir mentioned that instead of creating a new whiteout object for every rename, we can create a static whiteout object with irrelevant nlink. That will make fast commits to not fall back to full commit. But until this happens, this patch will ensure correctness by falling back to full commits. Fixes: 8016e29f ("ext4: fast commit recovery path") Cc: stable@kernel.org Signed-off-by:
-
Jan Kara authored
When filesystem mount fails because of corrupted filesystem we first cancel the s_err_report timer reminding fs errors every day and only then we flush s_error_work. However s_error_work may report another fs error and re-arm timer thus resulting in timer use-after-free. Fix the problem by first flushing the work and only after that canceling the s_err_report timer. Reported-by: syzbot+628472a2aac693ab0fcd@syzkaller.appspotmail.com Fixes: 2d01ddc8 ("ext4: save error info to sb through journal if available") CC: stable@vger.kernel.org Signed-off-by:
Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20210315165906.2175-1-jack@suse.czSigned-off-by:
-
Shijie Luo authored
If set_large_file = 1 and errors occur in ext4_handle_dirty_metadata(), the error code will be overridden, go to out_brelse to avoid this situation. Signed-off-by:
Shijie Luo <luoshijie1@huawei.com> Link: https://lore.kernel.org/r/20210312065051.36314-1-luoshijie1@huawei.com Cc: stable@kernel.org Reviewed-by:
-
