From Nicolas Ferre:
More DT material for AT91:

- conversion of watchdog to DT
- usart definition for evk-pro3 board

* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91:
  ARM: at91/dts: evk-pro3: enable watchdog
  ARM: at91/dts: add at91sam9_wdt driver to at91sam926x, at91sam9g45
  watchdog: at91sam9_wdt: add device tree support
  ARM: at91: dt: evk-pro3: enable uart0 and uart2

The dtb targets belong in arch/arm/boot/dts/Makefile now, so move the
newly added davinci targets there.
Signed-off-by: Olof Johansson <olof@lixom.net>

From Sekhar Nori:

These changes add DT boot support to DaVinci DA850
SoC.

* tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci:
  ARM: davinci: da850: generate dtbs for da850 boards
  ARM: davinci: add support for am1808 based EnBW CMC board
  ARM: davinci: da850 evm: add DT data
  ARM: davinci: da850: add SoC DT data
  ARM: davinci: da850: add DT boot support
  ARM: davinci: da8xx: add DA850 PRUSS support
  ARM: davinci: add platform hook to fetch the SRAM pool
  ARM: davinci: da850: changed SRAM allocator to shared ram.
  ARM: davinci: sram: switch from iotable to ioremapped regions
  uio: uio_pruss: replace private SRAM API with genalloc
  ARM: davinci: serial: provide API to initialze UART clocks
  ARM: davinci: convert platform code to use clk_prepare/clk_unprepare
Signed-off-by: Olof Johansson <olof@lixom.net>

From Shawn Guo <shawn.guo@linaro.org>:
It's based on imx/multiplatform branch.  Most of them are dts changes.
There are also a few imx6 improvement patches in there.

* tag 'imx-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: imx6q: select ARM and PL310 errata
  ARM: imx6q: print silicon version on boot
  ARM i.MX dts: Consistently add labels to devicenodes
  ARM: dts: imx6q-sabresd: add volume up/down gpio keys
  ARM: dts: imx53: pinctl update
  ARM: imx: enable cpufreq for imx6q
  ARM: dts: imx6q: enable snvs lp rtc
  ARM: dts: imx6q-sabreauto: Add basic support
  ARM: imx6q: let users input debug uart port number
  ARM: dts: imx53-qsb: Make DA9053 regulator functional
  ARM: dts: imx53-qsb: Use pinctrl for gpio-led
  ARM i.MX dtsi: Add default bus-width property for esdhc controller
Signed-off-by: Arnd Bregmann <arnd@arndb.de>

From Shawn Guo <shawn.guo@linaro.org>:
It's mxs device tree changes for 3.8.  The majority is device tree
source updates.  One timer improvement and one defconfig update are
also included there.

* tag 'mxs-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs_defconfig: Improve USB related support
  ARM: mxs: apf28dev: Add I2C and SPI support
  ARM: mxs: Setup scheduler clock
  ARM: dts: mxs: Add hog pins to Crystalfontz boards
  ARM: dts: cfa10036: Use pinctrl for power led
  ARM: mxs: apf28dev: Add LCD and backlight support
  ARM: mxs: apf28dev: Add pinctrl and gpios
  ARM: dts: mxs: Add 16 bits LCD screen muxing options for I.MX28
  ARM: dts: cfa10049: Add the DH2228FV DAC to the DTS
  ARM: mxs: Add support for the Armadeus Systems APF28Dev docking board
  ARM: mx28: Skip OCOTP FEC MAC setup if in DT
  ARM: dts: mxs: Add PWM3 muxing options for i.MX28
  ARM: mxs: Add support for the Armadeus Systems APF28 module
  ARM: dts: cfa10049: Add FEC to the CFA-10049 expansion board
  ARM: dts: imx23-olinuxino: Use pinctrl for gpio-led
  ARM: dts: imx23-olinuxino: Remove unneeded "default-on"
  ARM: dts: imx28-evk: Use pinctrl for gpio-led
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

From Michal Simek <michal.simek@xilinx.com>:

These are based on previous patches (arm-soc zynq/cleanup branch).
The branch is still based on rc3 but I have also tried to merged it
with the v3.7-rc5 and there is no issue.

* 'arm-next' of git://git.xilinx.com/linux-xlnx:
  ARM: zynq: add clk binding support to the ttc
  ARM: zynq: use zynq clk bindings
  clk: Add support for fundamental zynq clks
  ARM: zynq: dts: split up device tree
  ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
  ARM: zynq: dts: add description of the second uart
  ARM: zynq: move arm-specific sys_timer out of ttc
  zynq: move static peripheral mappings
  zynq: remove use of CLKDEV_LOOKUP
  zynq: use pl310 device tree bindings
  zynq: use GIC device tree bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

From Sascha Hauer <s.hauer@pengutronix.de>:

ARM i.MX dt updates for 3.8

* tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
  Add device tree file for the armadeus apf27
  ARM i.MX: Add Ka-Ro TX25 devicetree
  ARM i.MX25: Add devicetree
  ARM i.MX25: Add devicetree support
  ARM i.MX25: Add missing clock gates
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Tested on evk-pro3.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Tested on an at91sam9260 board (evk-pro3).
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Tested on an at91sam9260 board (evk-pro3)
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Select the following USB related options:

- USB Ethernet adapter (needed for mx23-olinuxino)
- Native language support (needed for mounting USB pen drives, for example)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM core r2p10 and PL310 r3p2 are integrated on imx6q.  Select
corresponding errata.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

i.MX6Q has 3 revisions 1.0, 1.1 and 1.2.  Print revision on boot.
Signed-off-by: Drew Moseley <drew_moseley@mentor.com>
[drew: add proper error checking for function imx6q_revision()]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Having labels before each node allows board bindings to reference
to nodes by using the &nodename {} notation. This way boards do not
have to resemble the whole devicetree layout. Due to less indention
needed the board files also get better readability. Since the label
make the documentation behind the nodes unnecessary it is removed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add volume up/down gpio keys support in imx6q-sabresd.dts.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This patch supplements pinctl support on i.MX53.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

It enables cpufreq support for imx6q with generic cpufreq-cpu0 driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input

Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

imx6q gets 5 uart ports in total.  Different board design may choose
different port as debug uart.  For example, imx6q-sabresd uses UART1,
imx6q-sabrelite uses UART2 and imx6q-arm2 uses UART4.  Rather than
bloating DEBUG_LL choice list with all these uart ports, the patch
introduces DEBUG_IMX6Q_UART_PORT for users to input uart port number
when DEBUG_IMX6Q_UART is selected inside DEBUG_LL choice.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Setup the GPIO7_11 pin as interrupt to the DA9053 and also rename the regulator nodes
so that they match with the datasheet.

This allows probing of DA9053 to succeed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:

leds-gpio leds.2: pins are not configured from the driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

According to Documentation/devicetree/bindings/mmc/mmc.txt bus-width
is a mandatory property. While this is currently enforced nowhere, it's
a good habit to just add the property now to allow to add common helper
functionality for the mmc property parsing later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This resolves a nontrivial conflict where the omap_prcm_restart
is removed in one branch but another use is added in another
branch.

Conflicts:
	arch/arm/mach-omap2/cm33xx.c
	arch/arm/mach-omap2/io.c
	arch/arm/mach-omap2/prm_common.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'omap-for-v3.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren <tony@atomide.com>:

Device tree related changes for omaps updating the
various .dts files, and timer related changes to allow
configuring the timer via device tree.

* tag 'omap-for-v3.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (48 commits)
  usb: musb: dsps: dt binding - add resources, example
  ARM: dts: omap4-sdp: Add pinmux configuration for HDMI
  ARM: dts: omap4-panda: Add pinmux configuration for HDMI
  ARM: dts: Makefile: Add the am335x-evmsk target in dtbs list
  ARM: dts: AM33XX: Add usbss node
  ARM: dts: AM33XX: Add push-buttons device tree data to am335x-evmsk
  ARM: dts: AM33XX: Add pinmux configuration for gpio-keys to EVMSK
  ARM: dts: AM33XX: Add user-leds device tree data to am335x-evmsk
  ARM: dts: AM33XX: Add pinmux configuration for gpio-leds to EVMSK
  ARM: dts: AM33XX: Add user-leds device tree data to am335x-bone
  ARM: dts: AM33XX: Add pinmux configuration for user-leds to BONE
  ARM: dts: AM33XX: Add volume-keys device tree data to am335x-evm
  ARM: dts: AM33XX: Add pinmux configuration for volume-keys to EVM
  ARM: dts: AM33XX: Add matrix keypad device tree data to am335x-evm
  ARM: dts: AM33XX: Add pinmux configuration for matrix keypad to EVM
  ARM: dts: omap5-evm: LPDDR2 memory device details for EVM
  ARM: dts: omap5: EMIF device tree data for OMAP5 boards
  ARM: dts: omap5-evm: Fix size of memory defined for EVM
  ARM: OMAP2+: Add device-tree support for 32kHz counter
  ARM: OMAP: Add DT support for timer driver
  ...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

These changes are needed for the following omap DT changes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add support for retrieving TTC configuration from device tree.  This
includes the ability to pull information about the driving clocks from
the of_clk bindings.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>

Make the Zynq platform use the newly created zynq clk bindings.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>

Provide simplified models for the necessary clocks on the zynq-7000
platform.  Currently, the PLLs, the CPU clock network, and the basic
peripheral clock networks (for SDIO, SMC, SPI, QSPI, UART) are modelled.

OF bindings are also provided and documented.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>

Fixes the following error:
  CC      arch/arm/mach-omap2/cm_common.o
arch/arm/mach-omap2/cm_common.c: In function ‘cm_register’:
arch/arm/mach-omap2/cm_common.c:42:11: error: ‘EINVAL’ undeclared (first use in this function)
arch/arm/mach-omap2/cm_common.c:42:11: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/mach-omap2/cm_common.c:45:11: error: ‘EEXIST’ undeclared (first use in this function)
arch/arm/mach-omap2/cm_common.c: In function ‘cm_unregister’:
arch/arm/mach-omap2/cm_common.c:66:11: error: ‘EINVAL’ undeclared (first use in this function)
make[1]: *** [arch/arm/mach-omap2/cm_common.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The purpose of the created zynq-7000.dtsi file is to describe the
hardware common to all Zynq 7000-based boards.  Also, get rid of the
zynq-ep107 device tree, since it is not hardware anyone can purchase.

Add a zc702 dts file based on the zynq-7000.dtsi.  Add it to the
dts/Makefile so it is built with the 'dtbs' target.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>

Basic support for the Ka-Ro i.MX25 based TX25 board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lothar Waßmann <LW@KARO-electronics.de>

This adds a i.MX25 dtsi file along with the i.MX25 clock tree
documentation. The devicetree should be fairly complete for:

- uart
- fec
- i2c
- spi
- pwm
- nand
- gpio
- wdog
- esdhc
- flexcan

The more exotic devices currently miss clock bindings.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>

This adds a i.MX25 dt machine descriptor and changes the clock
support to optionally initialize from dt.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>

This completes the list of clock gates on the i.MX25. There are
several clocks marked as reserved in the datasheet, but nevertheless
used in the Freescale kernel. Add some comments to their positions
and add 'reservedx' entries to the clk enum. This way we can replace
them with the real names should we need them later. Adding the reserved
entry names will help us keeping the clk numbers when moving to devicetree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Setup scheduler clock on ARM MXS platforms with a 32-bit timrot
such as i.MX28. This allows the scheduler to use sub-jiffy resolution.

The corresponding change for 16-bit v1 timrots is not possible
at the moment due to rounding issues with clock values wrapping
faster than once per several seconds in the common ARM platform code.
Signed-off-by: Stanislav Meduna <stano@meduna.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>