In the latest firmware the clear_pxe_mode function will use the
AdminQ request, so call this after AdminQ is set up rather than
relying on i40e_pf_reset() to clear the PXE mode.

Change-ID: Ice8cba2e9cbc3c7bde0a0bcf8eaf5009abef040b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure the "new" qtx_head[q] register is cleared before
enabling the Tx queue.

Change-ID: I0c7a12815e343a5ae68807af172a35d6c6857935
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Set the ITR max and min values to match the hardware max value
and the recommended min value.  These values are shifted right
one bit because the register counts in 2 usec units, so leave
a comment to explain.

Change-ID: I289c27955cf6c566a6d21b95c3110b88cbb15dad
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If the IPV6EXADD bit is set in the Rx descriptor status, there
was an optional extension header with an alternate IP address
detected.  The HW checksum offload doesn't handle the alternate
IP address correctly so likely comes up with the wrong answer.
Thus, if the bit is set we ignore the checksum offload value.

Change-ID: I70ff8d38cdcddccf44107691cae13d0c07c284c8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If you use ip to change the MAC address of a VF while the VF
driver is loaded, closing the VF interface or unloading the VF
driver will cause the VF driver to remove the MAC filter for its
original (now invalid) MAC address. This would cause the PF
driver to kick an error message to the log, and back to the VF
driver.

Since the VF driver has not really done anything naughty, let's
not punish it. Don't check for MAC address overrides on the
delete operation, just make sure it's a valid address. This keeps
us from spamming the log with confusing errors.

Change-ID: I1f051bd4014e50855457d928c9ee8b0766981b2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a bug where the driver was erroneously exiting the driver unload
path if one part of the unload failed.  Instead of the original way
the driver should always continue when disabling and be sure to disable
all queues.

Change-ID: Ib8c81c596bc87c31d8e9ca97ebf871168475279d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a bug where ethtool set-channels would return failure when configuring
only one Rx queue.

Change-ID: Id833c48c17d71e352b30f3249f6acf9e7aaec57e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

These changes make Doxygen/kdoc work correctly without warnings.

Change-ID: I2941f38860be805ff7548d84dae35754c83f1d62
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>

Avoid over-length lines in order to appease checkpatch.

Change-ID: I63820a710acf798f49d2f85c610228711af84f72
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Update driver version to 0.3.27-k
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The current driver will warn the user if the NVM version
is out of date, this raises the bar to a newer version.

Change-ID: I5ec21d8efa4e7c3fdacb56f85d310bb2229b1483
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

A previous commit removed any need for these macros, so remove
them too.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

These instances were found by coccinelle/spatch, and can
use struct assignment instead of memcpy.

Change-ID: Idc23c3599241bf8a658bda18c80417af3fbfee66
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The recent patch to improve guest receive side flow control (ca2f09f2) had a
slight flaw in the wait condition for the vif thread in that any remaining
skbs in the guest receive side netback internal queue would prevent the
thread from sleeping. An unresponsive frontend can lead to a permanently
non-empty internal queue and thus the thread will spin. In this case the
thread should really sleep until the frontend becomes responsive again.

This patch adds an extra flag to the vif which is set if the shared ring
is full and cleared when skbs are drained into the shared ring. Thus,
if the thread runs, finds the shared ring full and can make no progress the
flag remains set. If the flag remains set then the thread will sleep,
regardless of a non-empty queue, until the next event from the frontend.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huqiu reported current sh_sir driver doesn't
call free_irq() in spite of using request_irq().
This patch replaces request_irq() into devm_request_irq()
to solve this issue

Reported-by: Huqiu Liu<huqiuliu@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huqiu reported current sh_irda driver doesn't
call free_irq() in spite of using request_irq().
This patch replaces request_irq() into devm_request_irq()
to solve this issue

Reported-by: Huqiu Liu<huqiuliu@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SH_SIR is not Dongle
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
nf_tables updates for net-next

The following patchset contains the following nf_tables updates,
mostly updates from Patrick McHardy, they are:

* Add the "inet" table and filter chain type for this new netfilter
  family: NFPROTO_INET. This special table/chain allows IPv4 and IPv6
  rules, this should help to simplify the burden in the administration
  of dual stack firewalls. This also includes several patches to prepare
  the infrastructure for this new table and a new meta extension to
  match the layer 3 and 4 protocol numbers, from Patrick McHardy.

* Load both IPv4 and IPv6 conntrack modules in nft_ct if the rule is used
  in NFPROTO_INET, as we don't certainly know which one would be used,
  also from Patrick McHardy.

* Do not allow to delete a table that contains sets, otherwise these
  sets become orphan, from Patrick McHardy.

* Hold a reference to the corresponding nf_tables family module when
  creating a table of that family type, to avoid the module deletion
  when in use, from Patrick McHardy.

* Update chain counters before setting the chain policy to ensure that
  we don't leave the chain in inconsistent state in case of errors (aka.
  restore chain atomicity). This also fixes a possible leak if it fails
  to allocate the chain counters if no counters are passed to be restored,
  from Patrick McHardy.

* Don't check for overflows in the table counter if we are just renaming
  a chain, from Patrick McHardy.

* Replay the netlink request after dropping the nfnl lock to load the
  module that supports provides a chain type, from Patrick.

* Fix chain type module references, from Patrick.

* Several cleanups, function renames, constification and code
  refactorizations also from Patrick McHardy.

* Add support to set the connmark, this can be used to set it based on
  the meta mark (similar feature to -j CONNMARK --restore), from
  Kristian Evensen.

* A couple of fixes to the recently added meta/set support and nft_reject,
  and fix missing chain type unregistration if we fail to register our
  the family table/filter chain type, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We have to unregister chain type if this fails to register netns.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to i40e only.

Anjali provides a fix where interrupts were not being re-enabled on ICR0
even though they were auto masked by hardware.  Then provides a fix to
cleanup RSS initialization because it was doing some extra work, so
remove the extra work and any bugs it created when managing number of
queues.  Since hardware requires a full packet template to be pointed to
when adding hardware flow filters, add the template and use it for
programming filters.

Jesse provides a fix to replace the use of driver specific defines with
kernel ETH_ALEN defines.  Then disables packet split because with the
use of GRO, we do not need the extra bus overhead.  Fixes spelling
error in code comment.

Kamil provides a fix for the driver where the hardware expects the MAC
address in a very specific format and the driver was filing the data
incorrectly.

Mitch provides a fix to resolve a panic on reset by adding checks to
VSI->rx_rings.  Then shortens alloc_rx_buff_failed and
alloc_rx_page_failed variables since both part of an RX specific
structure so just remove the _rx part of the name.  Then fixes
badly formatted lines, long lines and mis-formatted lines.

Shannon provides a fix to call AQ to release any reservation held by this
PF on the NVM resource lock on startup, in order to clear anything that
might have been left over from a previous run.  Then removes interrupt on
AQ error since nearly everything we do is synchronous, using the
interrupt-on-error bit is unnecessary and causing unneeded interrupts.
Adds code to handle the ability to send messages among the physical
function interfaces by the admin queue.

Catherine sets the MFP flag earlier in software init and uses that flag
to decide if other hardware work-arounds are required which turns
off flow director in MFP mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

net/ipv4/ip_tunnel.c:116:18: warning:
 symbol 'tunnel_dst_check' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

memory allocated by kmem_cache_alloc() should be freed using
kmem_cache_free(), not kfree().

Fixes: e298e505 ('openvswitch: Per cpu flow stats.')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't encode argument types into function names and since besides
nft_do_chain() there are only AF-specific versions, there is no risk
of confusion.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

We currently leak the set memory when deleting a table that still has
sets in it. Return EBUSY when attempting to delete a table with sets.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The table refers to data of the AF module, so we need to make sure the
module isn't unloaded while the table exists.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Simplifies error handling. Additionally use the correct type u32 for the
host byte order flags value.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Minor nf_chain_type cleanups:

- reorder struct to plug a hoe
- rename struct module member to "owner" for consistency
- rename nf_hookfn array to "hooks" for consistency
- reorder initializers for better readability
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

To avoid races, we need to replay to request after dropping the nfnl_mutex
to auto-load the chain type module.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

In some cases we neither take a reference to the AF info nor to the
chain type, allowing the module to be unloaded while in use.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The chain type module reference handling makes no sense at all: we take
a reference immediately when the module is registered, preventing the
module from ever being unloaded.

Fix by taking a reference when we're actually creating a chain of the
chain type and release the reference when destroying the chain.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The table use counter is only increased for new chains, so move the check
to the correct position.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Chain counter validation is performed after the chain policy has
potentially been changed. Move counter validation/setting before
changing of the chain policy to fix this.

Additionally fix a memory leak if chain counter allocation fails
for new chains, remove an unnecessary free_percpu() and move
counter allocation for new chains
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Currently nf_tables_newchain() atomicity is broken because of having
validation of some netlink attributes performed after changing attributes
of the chain. The chain policy is (currently) fine, but split it up as
preparation for the following fixes and to avoid future mistakes.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

We have to validate that the input register is in the range of
allowed registers, otherwise we can take a incorrect register
value as input that may lead us to a crash.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This patch adds kernel support for setting properties of tracked
connections. Currently, only connmark is supported. One use-case
for this feature is to provide the same functionality as
-j CONNMARK --save-mark in iptables.

Some restructuring was needed to implement the set op. The new
structure follows that of nft_meta.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The driver needs to set the MFP flag earlier in i40e_sw_init
and then can use that flag to decide if other hardware
work-arouds are required.

Change-ID: Ib17ad1e3485f57b28845ab4722294a99f203bd48
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware requires a full packet template to be pointed to when adding
hardware flow filters.  This patch adds the template and uses it for
programming filters.

Change-ID: I09db9f4ab0207ca9c520ae36596d74e1a0663ae5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch does s/rebuid/rebuild/.

Change-ID: I77ff0c26db3d23ca5dc971b82d71b4ed8c6bcc14
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>