Several Qualcomm Bluetooth controllers lack persistent storage for the
device address and instead one can be provided by the boot firmware
using the 'local-bd-address' devicetree property.

The Bluetooth bindings clearly states that the address should be
specified in little-endian order, but due to a long-standing bug in the
Qualcomm driver which reversed the address some boot firmware has been
providing the address in big-endian order instead.

The only device out there that should be affected by this is the WCN3991
used in some Chromebooks.

Add a 'qcom,local-bd-address-broken' property which can be set on these
platforms to indicate that the boot firmware is using the wrong byte
order.

Note that ChromeOS always updates the kernel and devicetree in lockstep
so that there is no need to handle backwards compatibility with older
devicetrees.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This reverts commit 7dcd3e01.

Qualcomm Bluetooth controllers like WCN6855 do not have persistent
storage for the Bluetooth address and must therefore start as
unconfigured to allow the user to set a valid address unless one has
been provided by the boot firmware in the devicetree.

A recent change snuck into v6.8-rc7 and incorrectly started marking the
default (non-unique) address as valid. This specifically also breaks the
Bluetooth setup for some user of the Lenovo ThinkPad X13s.

Note that this is the second time Qualcomm breaks the driver this way
and that this was fixed last year by commit 6945795b ("Bluetooth:
fix use-bdaddr-property quirk"), which also has some further details.

Fixes: 7dcd3e01 ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Cc: stable@vger.kernel.org      # 6.8
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The current implementation for loading coalesced KPU profiles has
a limitation.  The "offset" field, which is used to locate profiles
within the profile is restricted to a u16.

This restricts the number of profiles that can be loaded. This patch
addresses this limitation by increasing the size of the "offset" field.

Fixes: 11c730bf ("octeontx2-af: support for coalescing KPU profiles")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
gro: various fixes related to UDP tunnels

We found issues when a UDP tunnel endpoint is in a different netns than
where UDP GRO happens. This kind of setup is actually quite diverse,
from having one leg of the tunnel on a remove host, to having a tunnel
between netns (eg. being bridged in another one or on the host). In our
case that UDP tunnel was geneve.

UDP tunnel packets should not be GROed at the UDP level. The fundamental
issue here is such packet can't be detected in a foolproof way: we can't
know by looking at a packet alone and the current logic of looking up
UDP sockets is fragile (socket could be in another netns, packet could
be modified in between, etc). Because there is no way to make the GRO
code to correctly handle those packets in all cases, this series aims at
two things: making the net stack to correctly behave (as in, no crash
and no invalid packet) when such thing happens, and in some cases to
prevent this "early GRO" from happening.

First three patches fix issues when an "UDP tunneled" packet is being
GROed too early by rx-udp-gro-forwarding or rx-gro-list.

Last patch is preventing locally generated UDP tunnel packets from being
GROed. This turns out to be more complex than this patch alone as it
relies on skb->encapsulation which is currently untrusty in some cases
(see iptunnel_handle_offloads); but that should fix things in practice
and is acceptable for a fix. Future work is required to improve things
(prevent all locally generated UDP tunnel packets from being GROed),
such as fixing the misuse of skb->encapsulation in drivers; but that
would be net-next material.

Thanks!
Antoine

Since v3:
  - Fixed the udpgro_fwd selftest in patch 5 (Jakub Kicinski feedback).
  - Improved commit message on patch 3 (Willem de Bruijn feeback).

Since v2:
  - Fixed a build issue with IPv6=m in patch 1 (Jakub Kicinski
    feedback).
  - Fixed typo in patch 1 (Nikolay Aleksandrov feedback).
  - Added Reviewed-by tag on patch 2 (Willem de Bruijn feeback).
  - Added back conversion to CHECKSUM_UNNECESSARY but only from non
    CHECKSUM_PARTIAL in patch 3 (Paolo Abeni & Willem de Bruijn
    feeback).
  - Reworded patch 3 commit msg.

Since v1:
  - Fixed a build issue with IPv6 disabled in patch 1.
  - Reworked commit log in patch 2 (Willem de Bruijn feedback).
  - Added Reviewed-by tags on patches 1 & 4 (Willem de Bruijn feeback).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

UDP tunnel packets can't be GRO in-between their endpoints as this
causes different issues. The UDP GRO fwd vxlan tests were relying on
this and their expectations have to be fixed.

We keep both vxlan tests and expected no GRO from happening. The vxlan
UDP GRO bench test was removed as it's not providing any valuable
information now.

Fixes: a062260a ("selftests: net: add UDP GRO forwarding self-tests")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

GRO has a fundamental issue with UDP tunnel packets as it can't detect
those in a foolproof way and GRO could happen before they reach the
tunnel endpoint. Previous commits have fixed issues when UDP tunnel
packets come from a remote host, but if those packets are issued locally
they could run into checksum issues.

If the inner packet has a partial checksum the information will be lost
in the GRO logic, either in udp4/6_gro_complete or in
udp_gro_complete_segment and packets will have an invalid checksum when
leaving the host.

Prevent local UDP tunnel packets from ever being GROed at the outer UDP
level.

Due to skb->encapsulation being wrongly used in some drivers this is
actually only preventing UDP tunnel packets with a partial checksum to
be GROed (see iptunnel_handle_offloads) but those were also the packets
triggering issues so in practice this should be sufficient.

Fixes: 9fd1ff5d ("udp: Support UDP fraglist GRO/GSO.")
Fixes: 36707061 ("udp: allow forwarding of plain (non-fraglisted) UDP GRO packets")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

UDP GRO validates checksums and in udp4/6_gro_complete fraglist packets
are converted to CHECKSUM_UNNECESSARY to avoid later checks. However
this is an issue for CHECKSUM_PARTIAL packets as they can be looped in
an egress path and then their partial checksums are not fixed.

Different issues can be observed, from invalid checksum on packets to
traces like:

  gen01: hw csum failure
  skb len=3008 headroom=160 headlen=1376 tailroom=0
  mac=(106,14) net=(120,40) trans=160
  shinfo(txflags=0 nr_frags=0 gso(size=0 type=0 segs=0))
  csum(0xffff232e ip_summed=2 complete_sw=0 valid=0 level=0)
  hash(0x77e3d716 sw=1 l4=1) proto=0x86dd pkttype=0 iif=12
  ...

Fix this by only converting CHECKSUM_NONE packets to
CHECKSUM_UNNECESSARY by reusing __skb_incr_checksum_unnecessary. All
other checksum types are kept as-is, including CHECKSUM_COMPLETE as
fraglist packets being segmented back would have their skb->csum valid.

Fixes: 9fd1ff5d ("udp: Support UDP fraglist GRO/GSO.")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If packets are GROed with fraglist they might be segmented later on and
continue their journey in the stack. In skb_segment_list those skbs can
be reused as-is. This is an issue as their destructor was removed in
skb_gro_receive_list but not the reference to their socket, and then
they can't be orphaned. Fix this by also removing the reference to the
socket.

For example this could be observed,

  kernel BUG at include/linux/skbuff.h:3131!  (skb_orphan)
  RIP: 0010:ip6_rcv_core+0x11bc/0x19a0
  Call Trace:
   ipv6_list_rcv+0x250/0x3f0
   __netif_receive_skb_list_core+0x49d/0x8f0
   netif_receive_skb_list_internal+0x634/0xd40
   napi_complete_done+0x1d2/0x7d0
   gro_cell_poll+0x118/0x1f0

A similar construction is found in skb_gro_receive, apply the same
change there.

Fixes: 5e10da53 ("skbuff: allow 'slow_gro' for skb carring sock reference")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When rx-udp-gro-forwarding is enabled UDP packets might be GROed when
being forwarded. If such packets might land in a tunnel this can cause
various issues and udp_gro_receive makes sure this isn't the case by
looking for a matching socket. This is performed in
udp4/6_gro_lookup_skb but only in the current netns. This is an issue
with tunneled packets when the endpoint is in another netns. In such
cases the packets will be GROed at the UDP level, which leads to various
issues later on. The same thing can happen with rx-gro-list.

We saw this with geneve packets being GROed at the UDP level. In such
case gso_size is set; later the packet goes through the geneve rx path,
the geneve header is pulled, the offset are adjusted and frag_list skbs
are not adjusted with regard to geneve. When those skbs hit
skb_fragment, it will misbehave. Different outcomes are possible
depending on what the GROed skbs look like; from corrupted packets to
kernel crashes.

One example is a BUG_ON[1] triggered in skb_segment while processing the
frag_list. Because gso_size is wrong (geneve header was pulled)
skb_segment thinks there is "geneve header size" of data in frag_list,
although it's in fact the next packet. The BUG_ON itself has nothing to
do with the issue. This is only one of the potential issues.

Looking up for a matching socket in udp_gro_receive is fragile: the
lookup could be extended to all netns (not speaking about performances)
but nothing prevents those packets from being modified in between and we
could still not find a matching socket. It's OK to keep the current
logic there as it should cover most cases but we also need to make sure
we handle tunnel packets being GROed too early.

This is done by extending the checks in udp_unexpected_gso: GSO packets
lacking the SKB_GSO_UDP_TUNNEL/_CSUM bits and landing in a tunnel must
be segmented.

[1] kernel BUG at net/core/skbuff.c:4408!
    RIP: 0010:skb_segment+0xd2a/0xf70
    __udp_gso_segment+0xaa/0x560

Fixes: 9fd1ff5d ("udp: Support UDP fraglist GRO/GSO.")
Fixes: 36707061 ("udp: allow forwarding of plain (non-fraglisted) UDP GRO packets")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up till now only single character ('A' or 'B') was used to provide
information of HSR slave network device status.

As it is also possible and valid, that Interlink network device may
be supported as well, the description must be more verbose. As a result
the full string description is now used.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2024-03-27 (e1000e)

This series contains updates to e1000e driver only.

Vitaly adds retry mechanism for some PHY operations to workaround MDI
error and moves SMBus configuration to avoid possible PHY loss.

* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue
  e1000e: Workaround for sporadic MDI error on Meteor Lake systems
====================

Link: https://lore.kernel.org/r/20240327185517.2587564-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Notice that skb_mark_for_recycle() is introduced later than fixes tag in
commit 6a5bcd84 ("page_pool: Allow drivers to hint on SKB recycling").

It is believed that fixes tag were missing a call to page_pool_release_page()
between v5.9 to v5.14, after which is should have used skb_mark_for_recycle().
Since v6.6 the call page_pool_release_page() were removed (in
commit 535b9c61 ("net: page_pool: hide page_pool_release_page()")
and remaining callers converted (in commit 6bfef2ec ("Merge branch
'net-page_pool-remove-page_pool_release_page'")).

This leak became visible in v6.8 via commit dba1b8a7 ("mm/page_pool: catch
page_pool memory leaks").

Cc: stable@vger.kernel.org
Fixes: 6c5aa6fc ("xen networking: add basic XDP support for xen-netfront")
Reported-by: Leonidas Spyropoulos <artafinde@archlinux.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218654Reported-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/171154167446.2671062.9127105384591237363.stgit@firesoulSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Emails to Jeff Sipek bounce:

  Your message to jsipek@vmware.com couldn't be delivered.
  Recipient is not authorized to accept external mail
  Status code: 550 5.7.1_ETR
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240327081413.306054-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Provide devlink documentation for three eswitch attributes:
mode, inline-mode, and encap-mode.
Signed-off-by: William Tu <witu@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20240325181228.6244-1-witu@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Paolo Abeni:
 "Including fixes from bpf, WiFi and netfilter.

  Current release - regressions:

   - ipv6: fix address dump when IPv6 is disabled on an interface

  Current release - new code bugs:

   - bpf: temporarily disable atomic operations in BPF arena

   - nexthop: fix uninitialized variable in nla_put_nh_group_stats()

  Previous releases - regressions:

   - bpf: protect against int overflow for stack access size

   - hsr: fix the promiscuous mode in offload mode

   - wifi: don't always use FW dump trig

   - tls: adjust recv return with async crypto and failed copy to
     userspace

   - tcp: properly terminate timers for kernel sockets

   - ice: fix memory corruption bug with suspend and rebuild

   - at803x: fix kernel panic with at8031_probe

   - qeth: handle deferred cc1

  Previous releases - always broken:

   - bpf: fix bug in BPF_LDX_MEMSX

   - netfilter: reject table flag and netdev basechain updates

   - inet_defrag: prevent sk release while still in use

   - wifi: pick the version of SESSION_PROTECTION_NOTIF

   - wwan: t7xx: split 64bit accesses to fix alignment issues

   - mlxbf_gige: call request_irq() after NAPI initialized

   - hns3: fix kernel crash when devlink reload during pf
     initialization"

* tag 'net-6.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (81 commits)
  inet: inet_defrag: prevent sk release while still in use
  Octeontx2-af: fix pause frame configuration in GMP mode
  net: lan743x: Add set RFE read fifo threshold for PCI1x1x chips
  net: bcmasp: Remove phy_{suspend/resume}
  net: bcmasp: Bring up unimac after PHY link up
  net: phy: qcom: at803x: fix kernel panic with at8031_probe
  netfilter: arptables: Select NETFILTER_FAMILY_ARP when building arp_tables.c
  netfilter: nf_tables: skip netdev hook unregistration if table is dormant
  netfilter: nf_tables: reject table flag and netdev basechain updates
  netfilter: nf_tables: reject destroy command to remove basechain hooks
  bpf: update BPF LSM designated reviewer list
  bpf: Protect against int overflow for stack access size
  bpf: Check bloom filter map value size
  bpf: fix warning for crash_kexec
  selftests: netdevsim: set test timeout to 10 minutes
  net: wan: framer: Add missing static inline qualifiers
  mlxbf_gige: call request_irq() after NAPI initialized
  tls: get psock ref after taking rxlock to avoid leak
  selftests: tls: add test with a partially invalid iov
  tls: adjust recv return with async crypto and failed copy to userspace
  ...

ip_local_out() and other functions can pass skb->sk as function argument.

If the skb is a fragment and reassembly happens before such function call
returns, the sk must not be released.

This affects skb fragments reassembled via netfilter or similar
modules, e.g. openvswitch or ct_act.c, when run as part of tx pipeline.

Eric Dumazet made an initial analysis of this bug.  Quoting Eric:
  Calling ip_defrag() in output path is also implying skb_orphan(),
  which is buggy because output path relies on sk not disappearing.

  A relevant old patch about the issue was :
  8282f274 ("inet: frag: Always orphan skbs inside ip_defrag()")

  [..]

  net/ipv4/ip_output.c depends on skb->sk being set, and probably to an
  inet socket, not an arbitrary one.

  If we orphan the packet in ipvlan, then downstream things like FQ
  packet scheduler will not work properly.

  We need to change ip_defrag() to only use skb_orphan() when really
  needed, ie whenever frag_list is going to be used.

Eric suggested to stash sk in fragment queue and made an initial patch.
However there is a problem with this:

If skb is refragmented again right after, ip_do_fragment() will copy
head->sk to the new fragments, and sets up destructor to sock_wfree.
IOW, we have no choice but to fix up sk_wmem accouting to reflect the
fully reassembled skb, else wmem will underflow.

This change moves the orphan down into the core, to last possible moment.
As ip_defrag_offset is aliased with sk_buff->sk member, we must move the
offset into the FRAG_CB, else skb->sk gets clobbered.

This allows to delay the orphaning long enough to learn if the skb has
to be queued or if the skb is completing the reasm queue.

In the former case, things work as before, skb is orphaned.  This is
safe because skb gets queued/stolen and won't continue past reasm engine.

In the latter case, we will steal the skb->sk reference, reattach it to
the head skb, and fix up wmem accouting when inet_frag inflates truesize.

Fixes: 7026b1dd ("netfilter: Pass socket pointer down through okfn().")
Diagnosed-by: Eric Dumazet <edumazet@google.com>
Reported-by: xingwei lee <xrivendell7@gmail.com>
Reported-by: yue sun <samsun1006219@gmail.com>
Reported-by: syzbot+e5167d7144a62715044c@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240326101845.30836-1-fw@strlen.deSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The Octeontx2 MAC block (CGX) has separate data paths (SMU and GMP) for
different speeds, allowing for efficient data transfer.

The previous patch which added pause frame configuration has a bug due
to which pause frame feature is not working in GMP mode.

This patch fixes the issue by configurating appropriate registers.

Fixes: f7e086e7 ("octeontx2-af: Pause frame configuration at cgx")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326052720.4441-1-hkelam@marvell.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

PCI11x1x Rev B0 devices might drop packets when receiving back to back frames
at 2.5G link speed. Change the B0 Rev device's Receive filtering Engine FIFO
threshold parameter from its hardware default of 4 to 3 dwords to prevent the
problem. Rev C0 and later hardware already defaults to 3 dwords.

Fixes: bb4f6bff ("net: lan743x: Add PCI11010 / PCI11414 device IDs")
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326065805.686128-1-Raju.Lakkaraju@microchip.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Justin Chen says:

====================
net: bcmasp: phy managements fixes

Fix two issues.

- The unimac may be put in a bad state if PHY RX clk doesn't exist
  during reset. Work around this by bringing the unimac out of reset
  during phy up.

- Remove redundant phy_{suspend/resume}
====================

Link: https://lore.kernel.org/r/20240325193025.1540737-1-justin.chen@broadcom.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

phy_{suspend/resume} is redundant. It gets called from phy_{stop/start}.

Fixes: 490cb412 ("net: bcmasp: Add support for ASP2.0 Ethernet controller")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The unimac requires the PHY RX clk during reset or it may be put
into a bad state. Bring up the unimac after link up to ensure the
PHY RX clk exists.

Fixes: 490cb412 ("net: bcmasp: Add support for ASP2.0 Ethernet controller")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

On reworking and splitting the at803x driver, in splitting function of
at803x PHYs it was added a NULL dereference bug where priv is referenced
before it's actually allocated and then is tried to write to for the
is_1000basex and is_fiber variables in the case of at8031, writing on
the wrong address.

Fix this by correctly setting priv local variable only after
at803x_probe is called and actually allocates priv in the phydev struct.
Reported-by: William Wortel <wwortel@dorpstraat.com>
Cc: <stable@vger.kernel.org>
Fixes: 25d2ba94 ("net: phy: at803x: move specific at8031 probe mode check to dedicated probe")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240325190621.2665-1-ansuelsmth@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

Patch #1 reject destroy chain command to delete device hooks in netdev
         family, hence, only delchain commands are allowed.

Patch #2 reject table flag update interference with netdev basechain
	 hook updates, this can leave hooks in inconsistent
	 registration/unregistration state.

Patch #3 do not unregister netdev basechain hooks if table is dormant.
	 Otherwise, splat with double unregistration is possible.

Patch #4 fixes Kconfig to allow to restore IP_NF_ARPTABLES,
	 from Kuniyuki Iwashima.

There are a more fixes still in progress on my side that need more work.

* tag 'nf-24-03-28' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: arptables: Select NETFILTER_FAMILY_ARP when building arp_tables.c
  netfilter: nf_tables: skip netdev hook unregistration if table is dormant
  netfilter: nf_tables: reject table flag and netdev basechain updates
  netfilter: nf_tables: reject destroy command to remove basechain hooks
====================

Link: https://lore.kernel.org/r/20240328031855.2063-1-pablo@netfilter.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Alexei Starovoitov says:

====================
pull-request: bpf 2024-03-27

The following pull-request contains BPF updates for your *net* tree.

We've added 4 non-merge commits during the last 1 day(s) which contain
a total of 5 files changed, 26 insertions(+), 3 deletions(-).

The main changes are:

1) Fix bloom filter value size validation and protect the verifier
   against such mistakes, from Andrei.

2) Fix build due to CONFIG_KEXEC_CORE/CRASH_DUMP split, from Hari.

3) Update bpf_lsm maintainers entry, from Matt.

* tag 'for-net' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  bpf: update BPF LSM designated reviewer list
  bpf: Protect against int overflow for stack access size
  bpf: Check bloom filter map value size
  bpf: fix warning for crash_kexec
====================

Link: https://lore.kernel.org/r/20240328012938.24249-1-alexei.starovoitov@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Pull erofs fixes from Gao Xiang:

 - Add a new reviewer Sandeep Dhavale to build a healthier community

 - Drop experimental warning for FSDAX

* tag 'erofs-for-6.9-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  MAINTAINERS: erofs: add myself as reviewer
  erofs: drop experimental warning for FSDAX

syzkaller started to report a warning below [0] after consuming the
commit 4654467d ("netfilter: arptables: allow xtables-nft only
builds").

The change accidentally removed the dependency on NETFILTER_FAMILY_ARP
from IP_NF_ARPTABLES.

If NF_TABLES_ARP is not enabled on Kconfig, NETFILTER_FAMILY_ARP will
be removed and some code necessary for arptables will not be compiled.

  $ grep -E "(NETFILTER_FAMILY_ARP|IP_NF_ARPTABLES|NF_TABLES_ARP)" .config
  CONFIG_NETFILTER_FAMILY_ARP=y
  # CONFIG_NF_TABLES_ARP is not set
  CONFIG_IP_NF_ARPTABLES=y

  $ make olddefconfig

  $ grep -E "(NETFILTER_FAMILY_ARP|IP_NF_ARPTABLES|NF_TABLES_ARP)" .config
  # CONFIG_NF_TABLES_ARP is not set
  CONFIG_IP_NF_ARPTABLES=y

So, when nf_register_net_hooks() is called for arptables, it will
trigger the splat below.

Now IP_NF_ARPTABLES is only enabled by IP_NF_ARPFILTER, so let's
restore the dependency on NETFILTER_FAMILY_ARP in IP_NF_ARPFILTER.

[0]:
WARNING: CPU: 0 PID: 242 at net/netfilter/core.c:316 nf_hook_entry_head+0x1e1/0x2c0 net/netfilter/core.c:316
Modules linked in:
CPU: 0 PID: 242 Comm: syz-executor.0 Not tainted 6.8.0-12821-g537c2e91 #10
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:nf_hook_entry_head+0x1e1/0x2c0 net/netfilter/core.c:316
Code: 83 fd 04 0f 87 bc 00 00 00 e8 5b 84 83 fd 4d 8d ac ec a8 0b 00 00 e8 4e 84 83 fd 4c 89 e8 5b 5d 41 5c 41 5d c3 e8 3f 84 83 fd <0f> 0b e8 38 84 83 fd 45 31 ed 5b 5d 4c 89 e8 41 5c 41 5d c3 e8 26
RSP: 0018:ffffc90000b8f6e8 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 0000000000000003 RCX: ffffffff83c42164
RDX: ffff888106851180 RSI: ffffffff83c42321 RDI: 0000000000000005
RBP: 0000000000000000 R08: 0000000000000005 R09: 000000000000000a
R10: 0000000000000003 R11: ffff8881055c2f00 R12: ffff888112b78000
R13: 0000000000000000 R14: ffff8881055c2f00 R15: ffff8881055c2f00
FS:  00007f377bd78800(0000) GS:ffff88811b000000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000496068 CR3: 000000011298b003 CR4: 0000000000770ef0
PKRU: 55555554
Call Trace:
 <TASK>
 __nf_register_net_hook+0xcd/0x7a0 net/netfilter/core.c:428
 nf_register_net_hook+0x116/0x170 net/netfilter/core.c:578
 nf_register_net_hooks+0x5d/0xc0 net/netfilter/core.c:594
 arpt_register_table+0x250/0x420 net/ipv4/netfilter/arp_tables.c:1553
 arptable_filter_table_init+0x41/0x60 net/ipv4/netfilter/arptable_filter.c:39
 xt_find_table_lock+0x2e9/0x4b0 net/netfilter/x_tables.c:1260
 xt_request_find_table_lock+0x2b/0xe0 net/netfilter/x_tables.c:1285
 get_info+0x169/0x5c0 net/ipv4/netfilter/arp_tables.c:808
 do_arpt_get_ctl+0x3f9/0x830 net/ipv4/netfilter/arp_tables.c:1444
 nf_getsockopt+0x76/0xd0 net/netfilter/nf_sockopt.c:116
 ip_getsockopt+0x17d/0x1c0 net/ipv4/ip_sockglue.c:1777
 tcp_getsockopt+0x99/0x100 net/ipv4/tcp.c:4373
 do_sock_getsockopt+0x279/0x360 net/socket.c:2373
 __sys_getsockopt+0x115/0x1e0 net/socket.c:2402
 __do_sys_getsockopt net/socket.c:2412 [inline]
 __se_sys_getsockopt net/socket.c:2409 [inline]
 __x64_sys_getsockopt+0xbd/0x150 net/socket.c:2409
 do_syscall_x64 arch/x86/entry/common.c:52 [inline]
 do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83
 entry_SYSCALL_64_after_hwframe+0x46/0x4e
RIP: 0033:0x7f377beca6fe
Code: 1f 44 00 00 48 8b 15 01 97 0a 00 f7 d8 64 89 02 b8 ff ff ff ff eb b8 0f 1f 44 00 00 f3 0f 1e fa 49 89 ca b8 37 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 0a c3 66 0f 1f 84 00 00 00 00 00 48 8b 15 c9
RSP: 002b:00000000005df728 EFLAGS: 00000246 ORIG_RAX: 0000000000000037
RAX: ffffffffffffffda RBX: 00000000004966e0 RCX: 00007f377beca6fe
RDX: 0000000000000060 RSI: 0000000000000000 RDI: 0000000000000003
RBP: 000000000042938a R08: 00000000005df73c R09: 00000000005df800
R10: 00000000004966e8 R11: 0000000000000246 R12: 0000000000000003
R13: 0000000000496068 R14: 0000000000000003 R15: 00000000004bc9d8
 </TASK>

Fixes: 4654467d ("netfilter: arptables: allow xtables-nft only builds")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Skip hook unregistration when adding or deleting devices from an
existing netdev basechain. Otherwise, commit/abort path try to
unregister hooks which not enabled.

Fixes: b9703ed4 ("netfilter: nf_tables: support for adding new devices to an existing netdev chain")
Fixes: 7d937b10 ("netfilter: nf_tables: support for deleting devices in an existing netdev chain")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

netdev basechain updates are stored in the transaction object hook list.
When setting on the table dormant flag, it iterates over the existing
hooks in the basechain. Thus, skipping the hooks that are being
added/deleted in this transaction, which leaves hook registration in
inconsistent state.

Reject table flag updates in combination with netdev basechain updates
in the same batch:

- Update table flags and add/delete basechain: Check from basechain update
  path if there are pending flag updates for this table.
- add/delete basechain and update table flags: Iterate over the transaction
  list to search for basechain updates from the table update path.

In both cases, the batch is rejected. Based on suggestion from Florian Westphal.

Fixes: b9703ed4 ("netfilter: nf_tables: support for adding new devices to an existing netdev chain")
Fixes: 7d937b10 ("netfilter: nf_tables: support for deleting devices in an existing netdev chain")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Report EOPNOTSUPP if NFT_MSG_DESTROYCHAIN is used to delete hooks in an
existing netdev basechain, thus, only NFT_MSG_DELCHAIN is allowed.

Fixes: 7d937b10 ("netfilter: nf_tables: support for deleting devices in an existing netdev chain")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Kalle Valo says:

====================
wireless fixes for v6.9-rc2

The first fixes for v6.9. Ping-Ke Shih now maintains a separate tree
for Realtek drivers, document that in the MAINTAINERS. Plenty of fixes
for both to stack and iwlwifi. Our kunit tests were working only on um
architecture but that's fixed now.

* tag 'wireless-2024-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (21 commits)
  MAINTAINERS: wifi: mwifiex: add Francesco as reviewer
  kunit: fix wireless test dependencies
  wifi: iwlwifi: mvm: include link ID when releasing frames
  wifi: iwlwifi: mvm: handle debugfs names more carefully
  wifi: iwlwifi: mvm: guard against invalid STA ID on removal
  wifi: iwlwifi: read txq->read_ptr under lock
  wifi: iwlwifi: fw: don't always use FW dump trig
  wifi: iwlwifi: mvm: rfi: fix potential response leaks
  wifi: mac80211: correctly set active links upon TTLM
  wifi: iwlwifi: mvm: Configure the link mapping for non-MLD FW
  wifi: iwlwifi: mvm: consider having one active link
  wifi: iwlwifi: mvm: pick the version of SESSION_PROTECTION_NOTIF
  wifi: mac80211: fix prep_connection error path
  wifi: cfg80211: fix rdev_dump_mpp() arguments order
  wifi: iwlwifi: mvm: disable MLO for the time being
  wifi: cfg80211: add a flag to disable wireless extensions
  wifi: mac80211: fix ieee80211_bss_*_flags kernel-doc
  wifi: mac80211: check/clear fast rx for non-4addr sta VLAN changes
  wifi: mac80211: fix mlme_link_id_dbg()
  MAINTAINERS: wifi: add git tree for Realtek WiFi drivers
  ...
====================

Link: https://lore.kernel.org/r/20240327191346.1A1EAC433C7@smtp.kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull 9p fixes from Eric Van Hensbergen:
 "Two of these fix syzbot reported issues, and the other fixes a unused
  variable in some configurations"

* tag '9p-fixes-for-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  fs/9p: fix uninitialized values during inode evict
  fs/9p: remove redundant pointer v9ses
  fs/9p: fix uaf in in v9fs_stat2inode_dotl

Pull btrfs fixes from David Sterba:

 - fix race when reading extent buffer and 'uptodate' status is missed
   by one thread (introduced in 6.5)

 - do additional validation of devices using major:minor numbers

 - zoned mode fixes:
     - use zone-aware super block access during scrub
     - fix use-after-free during device replace (found by KASAN)
     - also delete zones that are 100% unusable to reclaim space

 - extent unpinning fixes:
     - fix extent map leak after error handling
     - print correct range in error message

 - error code and message updates

* tag 'for-6.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: fix race in read_extent_buffer_pages()
  btrfs: return accurate error code on open failure in open_fs_devices()
  btrfs: zoned: don't skip block groups with 100% zone unusable
  btrfs: use btrfs_warn() to log message at btrfs_add_extent_mapping()
  btrfs: fix message not properly printing interval when adding extent map
  btrfs: fix warning messages not printing interval at unpin_extent_range()
  btrfs: fix extent map leak in unexpected scenario at unpin_extent_cache()
  btrfs: validate device maj:min during open
  btrfs: zoned: fix use-after-free in do_zone_finish()
  btrfs: zoned: use zone aware sb location for scrub

Merge tag 'mm-hotfixes-stable-2024-03-27-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm

Pull misc fixes from Andrew Morton:
 "Various hotfixes. About half are cc:stable and the remainder address
  post-6.8 issues or aren't considered suitable for backporting.

  zswap figures prominently in the post-6.8 issues - folloup against the
  large amount of changes we have just made to that code.

  Apart from that, all over the map"

* tag 'mm-hotfixes-stable-2024-03-27-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
  crash: use macro to add crashk_res into iomem early for specific arch
  mm: zswap: fix data loss on SWP_SYNCHRONOUS_IO devices
  selftests/mm: fix ARM related issue with fork after pthread_create
  hexagon: vmlinux.lds.S: handle attributes section
  userfaultfd: fix deadlock warning when locking src and dst VMAs
  tmpfs: fix race on handling dquot rbtree
  selftests/mm: sigbus-wp test requires UFFD_FEATURE_WP_HUGETLBFS_SHMEM
  mm: zswap: fix writeback shinker GFP_NOIO/GFP_NOFS recursion
  ARM: prctl: reject PR_SET_MDWE on pre-ARMv6
  prctl: generalize PR_SET_MDWE support check to be per-arch
  MAINTAINERS: remove incorrect M: tag for dm-devel@lists.linux.dev
  mm: zswap: fix kernel BUG in sg_init_one
  selftests: mm: restore settings from only parent process
  tools/Makefile: remove cgroup target
  mm: cachestat: fix two shmem bugs
  mm: increase folio batch size
  mm,page_owner: fix recursion
  mailmap: update entry for Leonard Crestez
  init: open /initrd.image with O_LARGEFILE
  selftests/mm: Fix build with _FORTIFY_SOURCE
  ...

Forcing SMBUS inside the ULP enabling flow leads to sporadic PHY loss on
some systems. It is suspected to be caused by initiating PHY transactions
before the interface settles.

Separating this configuration from the ULP enabling flow and moving it to
the shutdown function allows enough time for the interface to settle and
avoids adding a delay.

Fixes: 6607c99e ("e1000e: i219 - fix to enable both ULP and EEE in Sx state")
Co-developed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

On some Meteor Lake systems accessing the PHY via the MDIO interface may
result in an MDI error. This issue happens sporadically and in most cases
a second access to the PHY via the MDIO interface results in success.

As a workaround, introduce a retry counter which is set to 3 on Meteor
Lake systems. The driver will only return an error if 3 consecutive PHY
access attempts fail. The retry mechanism is disabled in specific flows,
where MDI errors are expected.

Fixes: cc23f4f0 ("e1000e: Add support for Meteor Lake")
Suggested-by: Nikolay Mushayev <nikolay.mushayev@intel.com>
Co-developed-by: Nir Efrati <nir.efrati@intel.com>
Signed-off-by: Nir Efrati <nir.efrati@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Adding myself in place of both Brendan and Florent as both have since
moved on from working on the BPF LSM and will no longer be devoting
their time to maintaining the BPF LSM.
Signed-off-by: Matt Bobrowski <mattbobrowski@google.com>
Acked-by: KP Singh <kpsingh@kernel.org>
Link: https://lore.kernel.org/r/ZgMhWF_egdYF8t4D@google.comSigned-off-by: Alexei Starovoitov <ast@kernel.org>

Merge tag 'probes-fixes-v6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace

Pull probes fixlet from Masami Hiramatsu:

 - tracing/probes: initialize a 'val' local variable with zero.

   This variable is read by FETCH_OP_ST_EDATA in a loop, and is
   initialized by FETCH_OP_ARG in the same loop. Since this
   initialization is not obvious, smatch warns about it.

   Explicitly initializing 'val' with zero fixes this warning.

* tag 'probes-fixes-v6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  tracing: probes: Fix to zero initialize a local variable

Pull execve fixes from Kees Cook:

 - Fix selftests to conform to the TAP output format (Muhammad Usama
   Anjum)

 - Fix NOMMU linux_binprm::exec pointer in auxv (Max Filippov)

 - Replace deprecated strncpy usage (Justin Stitt)

 - Replace another /bin/sh instance in selftests

* tag 'execve-v6.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  binfmt: replace deprecated strncpy
  exec: Fix NOMMU linux_binprm::exec in transfer_args_to_stack()
  selftests/exec: Convert remaining /bin/sh to /bin/bash
  selftests/exec: execveat: Improve debug reporting
  selftests/exec: recursion-depth: conform test to TAP format output
  selftests/exec: load_address: conform test to TAP format output
  selftests/exec: binfmt_script: Add the overall result line according to TAP

Andrei Matei says:

====================
Check bloom filter map value size

v1->v2:
- prepend a patch addressing the bloom map specifically
- change low-level rejection error to EFAULT, to indicate a bug
====================

Link: https://lore.kernel.org/r/20240327024245.318299-1-andreimatei1@gmail.comSigned-off-by: Alexei Starovoitov <ast@kernel.org>

This patch re-introduces protection against the size of access to stack
memory being negative; the access size can appear negative as a result
of overflowing its signed int representation. This should not actually
happen, as there are other protections along the way, but we should
protect against it anyway. One code path was missing such protections
(fixed in the previous patch in the series), causing out-of-bounds array
accesses in check_stack_range_initialized(). This patch causes the
verification of a program with such a non-sensical access size to fail.

This check used to exist in a more indirect way, but was inadvertendly
removed in a833a17a.

Fixes: a833a17a ("bpf: Fix verification of indirect var-off stack access")
Reported-by: syzbot+33f4297b5f927648741a@syzkaller.appspotmail.com
Reported-by: syzbot+aafd0513053a1cbf52ef@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/bpf/CAADnVQLORV5PT0iTAhRER+iLBTkByCYNBYyvBSgjN1T31K+gOw@mail.gmail.com/Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Andrei Matei <andreimatei1@gmail.com>
Link: https://lore.kernel.org/r/20240327024245.318299-3-andreimatei1@gmail.comSigned-off-by: Alexei Starovoitov <ast@kernel.org>