Under rare conditions where repair code may be used it is possible that
window probes are either unnecessary or undesired. If the user knows that
window probes are not wanted or needed this change allows them to skip
sending them when a socket comes out of repair.
Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a bug where the sequence numbers of a socket created using
TCP repair functionality are lower than set after connect is called.
This occurs when the repair socket overlaps with a TIME-WAIT socket and
triggers the re-use code. The amount lower is equal to the number of times
that a particular IP/port set is re-used and then put back into TIME-WAIT.
Re-using the first time the sequence number is 1 lower, closing that socket
and then re-opening (with repair) a new socket with the same addresses/ports
puts the sequence number 2 lower than set via setsockopt. The third time is
3 lower, etc. I have not tested what the limit of this acrewal is, if any.

The fix is, if a socket is in repair mode, to respect the already set
sequence number and timestamp when it would have already re-used the
TIME-WAIT socket.
Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When fq_codel_init fails, qdisc_create_dflt will cleanup by using
qdisc_destroy. This function calls the ->reset() op prior to calling the
->destroy() op.

Unfortunately, during the failure flow for sch_fq_codel, the ->flows
parameter is not initialized, so the fq_codel_reset function will null
pointer dereference.

   kernel: BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
   kernel: IP: fq_codel_reset+0x58/0xd0 [sch_fq_codel]
   kernel: PGD 0 P4D 0
   kernel: Oops: 0000 [#1] SMP PTI
   kernel: Modules linked in: i40iw i40e(OE) xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack tun bridge stp llc devlink ebtable_filter ebtables ip6table_filter ip6_tables rpcrdma ib_isert iscsi_target_mod sunrpc ib_iser libiscsi scsi_transport_iscsi ib_srpt target_core_mod ib_srp scsi_transport_srp ib_ipoib rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm intel_rapl sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp kvm irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel intel_cstate iTCO_wdt iTCO_vendor_support intel_uncore ib_core intel_rapl_perf mei_me mei joydev i2c_i801 lpc_ich ioatdma shpchp wmi sch_fq_codel xfs libcrc32c mgag200 ixgbe drm_kms_helper isci ttm firewire_ohci
   kernel:  mdio drm igb libsas crc32c_intel firewire_core ptp pps_core scsi_transport_sas crc_itu_t dca i2c_algo_bit ipmi_si ipmi_devintf ipmi_msghandler [last unloaded: i40e]
   kernel: CPU: 10 PID: 4219 Comm: ip Tainted: G           OE    4.16.13custom-fq-codel-test+ #3
   kernel: Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.05.0004.051120151007 05/11/2015
   kernel: RIP: 0010:fq_codel_reset+0x58/0xd0 [sch_fq_codel]
   kernel: RSP: 0018:ffffbfbf4c1fb620 EFLAGS: 00010246
   kernel: RAX: 0000000000000400 RBX: 0000000000000000 RCX: 00000000000005b9
   kernel: RDX: 0000000000000000 RSI: ffff9d03264a60c0 RDI: ffff9cfd17b31c00
   kernel: RBP: 0000000000000001 R08: 00000000000260c0 R09: ffffffffb679c3e9
   kernel: R10: fffff1dab06a0e80 R11: ffff9cfd163af800 R12: ffff9cfd17b31c00
   kernel: R13: 0000000000000001 R14: ffff9cfd153de600 R15: 0000000000000001
   kernel: FS:  00007fdec2f92800(0000) GS:ffff9d0326480000(0000) knlGS:0000000000000000
   kernel: CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
   kernel: CR2: 0000000000000008 CR3: 0000000c1956a006 CR4: 00000000000606e0
   kernel: Call Trace:
   kernel:  qdisc_destroy+0x56/0x140
   kernel:  qdisc_create_dflt+0x8b/0xb0
   kernel:  mq_init+0xc1/0xf0
   kernel:  qdisc_create_dflt+0x5a/0xb0
   kernel:  dev_activate+0x205/0x230
   kernel:  __dev_open+0xf5/0x160
   kernel:  __dev_change_flags+0x1a3/0x210
   kernel:  dev_change_flags+0x21/0x60
   kernel:  do_setlink+0x660/0xdf0
   kernel:  ? down_trylock+0x25/0x30
   kernel:  ? xfs_buf_trylock+0x1a/0xd0 [xfs]
   kernel:  ? rtnl_newlink+0x816/0x990
   kernel:  ? _xfs_buf_find+0x327/0x580 [xfs]
   kernel:  ? _cond_resched+0x15/0x30
   kernel:  ? kmem_cache_alloc+0x20/0x1b0
   kernel:  ? rtnetlink_rcv_msg+0x200/0x2f0
   kernel:  ? rtnl_calcit.isra.30+0x100/0x100
   kernel:  ? netlink_rcv_skb+0x4c/0x120
   kernel:  ? netlink_unicast+0x19e/0x260
   kernel:  ? netlink_sendmsg+0x1ff/0x3c0
   kernel:  ? sock_sendmsg+0x36/0x40
   kernel:  ? ___sys_sendmsg+0x295/0x2f0
   kernel:  ? ebitmap_cmp+0x6d/0x90
   kernel:  ? dev_get_by_name_rcu+0x73/0x90
   kernel:  ? skb_dequeue+0x52/0x60
   kernel:  ? __inode_wait_for_writeback+0x7f/0xf0
   kernel:  ? bit_waitqueue+0x30/0x30
   kernel:  ? fsnotify_grab_connector+0x3c/0x60
   kernel:  ? __sys_sendmsg+0x51/0x90
   kernel:  ? do_syscall_64+0x74/0x180
   kernel:  ? entry_SYSCALL_64_after_hwframe+0x3d/0xa2
   kernel: Code: 00 00 48 89 87 00 02 00 00 8b 87 a0 01 00 00 85 c0 0f 84 84 00 00 00 31 ed 48 63 dd 83 c5 01 48 c1 e3 06 49 03 9c 24 90 01 00 00 <48> 8b 73 08 48 8b 3b e8 6c 9a 4f f6 48 8d 43 10 48 c7 03 00 00
   kernel: RIP: fq_codel_reset+0x58/0xd0 [sch_fq_codel] RSP: ffffbfbf4c1fb620
   kernel: CR2: 0000000000000008
   kernel: ---[ end trace e81a62bede66274e ]---

This is caused because flows_cnt is non-zero, but flows hasn't been
initialized. fq_codel_init has left the private data in a partially
initialized state.

To fix this, reset flows_cnt to 0 when we fail to initialize.
Additionally, to make the state more consistent, also cleanup the flows
pointer when the allocation of backlogs fails.

This fixes the NULL pointer dereference, since both the for-loop and
memset in fq_codel_reset will be no-ops when flow_cnt is zero.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2018-07-12

This series contains updates to ixgbe and e100/e1000 kernel documentation.

Alex fixes ixgbe to ensure that we are more explicit about the ordering
of updates to the receive address register (RAR) table.

Dan Carpenter fixes an issue where we were reading one element beyond
the end of the array.

Mauro Carvalho Chehab fixes formatting issues in the e100.rst and
e1000.rst that were causing errors during 'make htmldocs'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/networking/e1000.rst:83: ERROR: Unexpected indentation.
    Documentation/networking/e1000.rst:84: WARNING: Block quote ends without a blank line; unexpected unindent.
    Documentation/networking/e1000.rst:173: WARNING: Definition list ends without a blank line; unexpected unindent.
    Documentation/networking/e1000.rst:236: WARNING: Definition list ends without a blank line; unexpected unindent.

While here, fix highlights and mark a table as such.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Documentation/networking/e100.rst:57: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:68: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:75: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:84: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:93: WARNING: Inline emphasis start-string without end-string.

While here, fix some highlights.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The ipsec->tx_tbl[] has IXGBE_IPSEC_MAX_SA_COUNT elements so the > needs
to be changed to >= so we don't read one element beyond the end of the
array.

Fixes: 59259470 ("ixgbe: process the Tx ipsec offload")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we are much more explicit about the ordering
of updates to the receive address register (RAR) table. Prior to this patch
I believe we may have been updating the table while entries were still
active, or possibly allowing for reordering of things since we weren't
explicitly flushing writes to either the lower or upper portion of the
register prior to accessing the other half.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Merge branch 'ieee802154-for-davem-2018-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan

Stefan Schmidt says:

====================
pull-request: ieee802154 for net 2018-07-11

An update from ieee802154 for your *net* tree.

Build system fix for a missing include from Arnd Bergmann.
Setting the IFLA_LINK for the lowpan parent from Lubomir Rintel.
Fixes for some RX corner cases in adf7242 driver by Michael Hennerich.
And some small patches to cleanup our BUG_ON vs WARN_ON usage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in qed_probe message.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was been observed that with a particular order of initialisation,
the netdev can be up, but the SFP module still has its TX_DISABLE
signal asserted.  This occurs when the network device brought up before
the SFP kernel module has been inserted by userspace.

This occurs because sfp-bus layer does not hear about the change in
network device state, and so assumes that it is still down.  Set
netdev->sfp when the upstream is registered to work around this problem.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

We fail to correctly clean up after a bus registration failure, which
can lead to an incorrect assumption about the registration state of
the upstream or sfp cage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

rhashtable_free_and_destroy() cancels re-hash deferred work
then walks and destroys elements. at this moment, some elements can be
still in future_tbl. that elements are not destroyed.

test case:
nft_rhash_destroy() calls rhashtable_free_and_destroy() to destroy
all elements of sets before destroying sets and chains.
But rhashtable_free_and_destroy() doesn't destroy elements of future_tbl.
so that splat occurred.

test script:
   %cat test.nft
   table ip aa {
	   map map1 {
		   type ipv4_addr : verdict;
		   elements = {
			   0 : jump a0,
			   1 : jump a0,
			   2 : jump a0,
			   3 : jump a0,
			   4 : jump a0,
			   5 : jump a0,
			   6 : jump a0,
			   7 : jump a0,
			   8 : jump a0,
			   9 : jump a0,
		}
	   }
	   chain a0 {
	   }
   }
   flush ruleset
   table ip aa {
	   map map1 {
		   type ipv4_addr : verdict;
		   elements = {
			   0 : jump a0,
			   1 : jump a0,
			   2 : jump a0,
			   3 : jump a0,
			   4 : jump a0,
			   5 : jump a0,
			   6 : jump a0,
			   7 : jump a0,
			   8 : jump a0,
			   9 : jump a0,
		   }
	   }
	   chain a0 {
	   }
   }
   flush ruleset

   %while :; do nft -f test.nft; done

Splat looks like:
[  200.795603] kernel BUG at net/netfilter/nf_tables_api.c:1363!
[  200.806944] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[  200.812253] CPU: 1 PID: 1582 Comm: nft Not tainted 4.17.0+ #24
[  200.820297] Hardware name: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 07/08/2015
[  200.830309] RIP: 0010:nf_tables_chain_destroy.isra.34+0x62/0x240 [nf_tables]
[  200.838317] Code: 43 50 85 c0 74 26 48 8b 45 00 48 8b 4d 08 ba 54 05 00 00 48 c7 c6 60 6d 29 c0 48 c7 c7 c0 65 29 c0 4c 8b 40 08 e8 58 e5 fd f8 <0f> 0b 48 89 da 48 b8 00 00 00 00 00 fc ff
[  200.860366] RSP: 0000:ffff880118dbf4d0 EFLAGS: 00010282
[  200.866354] RAX: 0000000000000061 RBX: ffff88010cdeaf08 RCX: 0000000000000000
[  200.874355] RDX: 0000000000000061 RSI: 0000000000000008 RDI: ffffed00231b7e90
[  200.882361] RBP: ffff880118dbf4e8 R08: ffffed002373bcfb R09: ffffed002373bcfa
[  200.890354] R10: 0000000000000000 R11: ffffed002373bcfb R12: dead000000000200
[  200.898356] R13: dead000000000100 R14: ffffffffbb62af38 R15: dffffc0000000000
[  200.906354] FS:  00007fefc31fd700(0000) GS:ffff88011b800000(0000) knlGS:0000000000000000
[  200.915533] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  200.922355] CR2: 0000557f1c8e9128 CR3: 0000000106880000 CR4: 00000000001006e0
[  200.930353] Call Trace:
[  200.932351]  ? nf_tables_commit+0x26f6/0x2c60 [nf_tables]
[  200.939525]  ? nf_tables_setelem_notify.constprop.49+0x1a0/0x1a0 [nf_tables]
[  200.947525]  ? nf_tables_delchain+0x6e0/0x6e0 [nf_tables]
[  200.952383]  ? nft_add_set_elem+0x1700/0x1700 [nf_tables]
[  200.959532]  ? nla_parse+0xab/0x230
[  200.963529]  ? nfnetlink_rcv_batch+0xd06/0x10d0 [nfnetlink]
[  200.968384]  ? nfnetlink_net_init+0x130/0x130 [nfnetlink]
[  200.975525]  ? debug_show_all_locks+0x290/0x290
[  200.980363]  ? debug_show_all_locks+0x290/0x290
[  200.986356]  ? sched_clock_cpu+0x132/0x170
[  200.990352]  ? find_held_lock+0x39/0x1b0
[  200.994355]  ? sched_clock_local+0x10d/0x130
[  200.999531]  ? memset+0x1f/0x40

V2:
 - free all tables requested by Herbert Xu
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Bug fixes.

These are bug fixes in error code paths, TC Flower VLAN TCI flow
checking bug fix, proper filtering of Broadcast packets if IFF_BROADCAST
is not set, and a bug fix in bnxt_get_max_rings() to return 0 ring
parameters when the return value is -ENOMEM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix bug in the error code path when bnxt_request_irq() returns failure.
bnxt_disable_napi() should not be called in this error path because
NAPI has not been enabled yet.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling bnxt_set_max_func_irqs() to modify the max IRQ count requested or
freed by the RDMA driver is flawed.  The max IRQ count is checked when
re-initializing the IRQ vectors and this can happen multiple times
during ifup or ethtool -L.  If the max IRQ is reduced and the RDMA
driver is operational, we may not initailize IRQs correctly.  This
problem shows up on VFs with very small number of MSIX.

There is no other logic that relies on the IRQ count excluding the ones
used by RDMA.  So we fix it by just removing the call to subtract or
add the IRQs used by RDMA.

Fixes: a588e458 ("bnxt_en: Add interface to support RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the driver assumes IFF_BROADCAST is always set and always sets
the broadcast filter.  Modify the code to set or clear the broadcast
filter according to the IFF_BROADCAST flag.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code returns -ENOMEM and does not bother to set the output
parameters to 0 when no rings are available.  Some callers, such as
bnxt_get_channels() will display garbage ring numbers when that happens.
Fix it by always setting the output parameters.

Fixes: 6e6c5a57 ("bnxt_en: Modify bnxt_get_max_rings() to support shared or non shared rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there aren't enough RX rings available, the driver will attempt to
use a single RX ring without the aggregation ring.  If that also
fails, the BNXT_FLAG_AGG_RINGS flag is cleared but the other ring
parameters are not set consistently to reflect that.  If more RX
rings become available at the next open, the RX rings will be in
an inconsistent state and may crash when freeing the RX rings.

Fix it by restoring the BNXT_FLAG_AGG_RINGS if not enough RX rings are
available to run without aggregation rings.

Fixes: bdbd1eb5 ("bnxt_en: Handle no aggregation ring gracefully.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible that OVS may set don’t care for DEI/CFI bit in
vlan_tci mask. Hence, checking for vlan_tci exact match will endup
in a vlan flow rejection.

This patch fixes the problem by checking for vlan_pcp and vid
separately, instead of checking for the entire vlan_tci.

Fixes: e85a9be9 (bnxt_en: do not allow wildcard matches for L2 flows)
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree:

1) Missing module autoloadfor icmp and icmpv6 x_tables matches,
   from Florian Westphal.

2) Possible non-linear access to TCP header from tproxy, from
   Mate Eckl.

3) Do not allow rbtree to be used for single elements, this patch
   moves all set backend into one single module since such thing
   can only happen if hashtable module is explicitly blacklisted,
   which should not ever be done.

4) Reject error and standard targets from nft_compat for sanity
   reasons, they are never used from there.

5) Don't crash on double hashsize module parameter, from Andrey
   Ryabinin.

6) Drop dst on skb before placing it in the fragmentation
   reassembly queue, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet reports:
 Here is a reproducer of an annoying bug detected by syzkaller on our production kernel
 [..]
 ./b78305423 enable_conntrack
 Then :
 sleep 60
 dmesg | tail -10
 [  171.599093] unregister_netdevice: waiting for lo to become free. Usage count = 2
 [  181.631024] unregister_netdevice: waiting for lo to become free. Usage count = 2
 [  191.687076] unregister_netdevice: waiting for lo to become free. Usage count = 2
 [  201.703037] unregister_netdevice: waiting for lo to become free. Usage count = 2
 [  211.711072] unregister_netdevice: waiting for lo to become free. Usage count = 2
 [  221.959070] unregister_netdevice: waiting for lo to become free. Usage count = 2

Reproducer sends ipv6 fragment that hits nfct defrag via LOCAL_OUT hook.
skb gets queued until frag timer expiry -- 1 minute.

Normally nf_conntrack_reasm gets called during prerouting, so skb has
no dst yet which might explain why this wasn't spotted earlier.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Loading the nf_conntrack module with doubled hashsize parameter, i.e.
	  modprobe nf_conntrack hashsize=12345 hashsize=12345
causes NULL-ptr deref.

If 'hashsize' specified twice, the nf_conntrack_set_hashsize() function
will be called also twice.
The first nf_conntrack_set_hashsize() call will set the
'nf_conntrack_htable_size' variable:

	nf_conntrack_set_hashsize()
		...
		/* On boot, we can set this without any fancy locking. */
		if (!nf_conntrack_htable_size)
			return param_set_uint(val, kp);

But on the second invocation, the nf_conntrack_htable_size is already set,
so the nf_conntrack_set_hashsize() will take a different path and call
the nf_conntrack_hash_resize() function. Which will crash on the attempt
to dereference 'nf_conntrack_hash' pointer:

	BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
	RIP: 0010:nf_conntrack_hash_resize+0x255/0x490 [nf_conntrack]
	Call Trace:
	 nf_conntrack_set_hashsize+0xcd/0x100 [nf_conntrack]
	 parse_args+0x1f9/0x5a0
	 load_module+0x1281/0x1a50
	 __se_sys_finit_module+0xbe/0xf0
	 do_syscall_64+0x7c/0x390
	 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Fix this, by checking !nf_conntrack_hash instead of
!nf_conntrack_htable_size. nf_conntrack_hash will be initialized only
after the module loaded, so the second invocation of the
nf_conntrack_set_hashsize() won't crash, it will just reinitialize
nf_conntrack_htable_size again.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

iptables-nft never requests these, but make this explicitly illegal.
If it were quested, kernel could oops as ->eval is NULL, furthermore,
the builtin targets have no owning module so its possible to rmmod
eb/ip/ip6_tables module even if they would be loaded.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Reissuing RC_RX every 400ms - to adjust for offset drift in
receiver see datasheet page 61, OCL section.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

Only enable RX mode if the netdev is opened.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

The check is valid but it does not warrant to crash the kernel. A
WARN_ON() is good enough here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

Instead of having the function name hard-coded (it might change and we
forgot to update them in the debug output) we can use __func__ instead
and also shorter the line so we do not need to break it. Also fix an
extra blank line while being here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

The check is valid but it does not warrant to crash the kernel. A
WARN_ON() is good enough here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

tcp_zerocopy_receive() relies on tcp_inq() to limit number of bytes
requested by user.

syzbot found that after tcp_disconnect(), tcp_inq() was returning
a stale value (number of bytes in queue before the disconnect).

Note that after this patch, ioctl(fd, SIOCINQ, &val) is also fixed
and returns 0, so this might be a candidate for all known linux kernels.

While we are at this, we probably also should clear urg_data to
avoid other syzkaller reports after it discovers how to deal with
urgent data.

syzkaller repro :

socket(PF_INET, SOCK_STREAM, IPPROTO_IP) = 3
bind(3, {sa_family=AF_INET, sin_port=htons(20000), sin_addr=inet_addr("224.0.0.1")}, 16) = 0
connect(3, {sa_family=AF_INET, sin_port=htons(20000), sin_addr=inet_addr("127.0.0.1")}, 16) = 0
send(3, ..., 4096, 0) = 4096
connect(3, {sa_family=AF_UNSPEC, sa_data="\0\0\0\0\0\0\0\0\0\0\0\0\0\0"}, 128) = 0
getsockopt(3, SOL_TCP, TCP_ZEROCOPY_RECEIVE, ..., [16]) = 0 // CRASH

Fixes: 05255b82 ("tcp: add TCP_ZEROCOPY_RECEIVE support for zerocopy receive")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2018-07-07

The following pull-request contains BPF updates for your *net* tree.

Plenty of fixes for different components:

1) A set of critical fixes for sockmap and sockhash, from John Fastabend.

2) fixes for several race conditions in af_xdp, from Magnus Karlsson.

3) hash map refcnt fix, from Mauricio Vasquez.

4) samples/bpf fixes, from Taeung Song.

5) ifup+mtu check for xdp_redirect, from Toshiaki Makita.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting the low threshold to 0 has no effect on frags allocation,
we need to clear high_thresh instead.

The code was pre-existent to commit 648700f7 ("inet: frags:
use rhashtables for reassembly units"), but before the above,
such assignment had a different role: prevent concurrent eviction
from the worker and the netns cleanup helper.

Fixes: 648700f7 ("inet: frags: use rhashtables for reassembly units")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When tcp_diag_destroy closes a TCP_NEW_SYN_RECV socket, it first
frees it by calling inet_csk_reqsk_queue_drop_and_and_put in
tcp_abort, and then frees it again by calling sock_gen_put.

Since tcp_abort only has one caller, and all the other codepaths
in tcp_abort don't free the socket, just remove the free in that
function.

Cc: David Ahern <dsa@cumulusnetworks.com>
Tested: passes Android sock_diag_test.py, which exercises this codepath
Fixes: d7226c7a ("net: diag: Fix refcnt leak in error path destroying socket")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin reported that icmp replies may not use the address on the device the
echo request is received if the destination address is broadcast. Instead
a route lookup is done without considering VRF context. Fix by setting
oif in flow struct to the master device if it is enslaved. That directs
the lookup to the VRF table. If the device is not enslaved, oif is still
0 so no affect.

Fixes: cd2fbe1b ("net: Use VRF device index for lookups on RX")
Reported-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise we end up with attempting to send packets from down devices
or to send oversized packets, which may cause unexpected driver/device
behaviour. Generic XDP has already done this check, so reuse the logic
in native XDP.

Fixes: 814abfab ("xdp: add bpf_redirect helper function")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

John Fastabend says:

====================
First three patches resolve issues found while testing sockhash and
reviewing code. Syzbot also found them about the same time as I was
working on fixes. The main issue is in the sockhash path we reduced
the scope of sk_callback lock but this meant we could get update and
close running in parallel so fix that here.

Then testing sk_msg and sk_skb programs together found that skb->dev
is not always assigned and some of the helpers were depending on this
to lookup max mtu. Fix this by using SKB_MAX_ALLOC when no MTU is
available.

Finally, Martin spotted that the sockmap code was still using the
qdisc skb cb structure. But I was sure we had fixed this long ago.
Looks like we missed it in a merge conflict resolution and then by
chance data_end offset was the same in both structures so everything
sort of continued to work even though it could break at any moment
if the structs ever change. So redo the conversion and this time
also convert the helpers.

v2: fix '0 files changed' issue in patches
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

In commit

  'bpf: bpf_compute_data uses incorrect cb structure' (8108a775)

we added the routine bpf_compute_data_end_sk_skb() to compute the
correct data_end values, but this has since been lost. In kernel
v4.14 this was correct and the above patch was applied in it
entirety. Then when v4.14 was merged into v4.15-rc1 net-next tree
we lost the piece that renamed bpf_compute_data_pointers to the
new function bpf_compute_data_end_sk_skb. This was done here,

e1ea2f98 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")

When it conflicted with the following rename patch,

6aaae2b6 ("bpf: rename bpf_compute_data_end into bpf_compute_data_pointers")

Finally, after a refactor I thought even the function
bpf_compute_data_end_sk_skb() was no longer needed and it was
erroneously removed.

However, we never reverted the sk_skb_convert_ctx_access() usage of
tcp_skb_cb which had been committed and survived the merge conflict.
Here we fix this by adding back the helper and *_data_end_sk_skb()
usage. Using the bpf_skc_data_end mapping is not correct because it
expects a qdisc_skb_cb object but at the sock layer this is not the
case. Even though it happens to work here because we don't overwrite
any data in-use at the socket layer and the cb structure is cleared
later this has potential to create some subtle issues. But, even
more concretely the filter.c access check uses tcp_skb_cb.

And by some act of chance though,

struct bpf_skb_data_end {
        struct qdisc_skb_cb        qdisc_cb;             /*     0    28 */

        /* XXX 4 bytes hole, try to pack */

        void *                     data_meta;            /*    32     8 */
        void *                     data_end;             /*    40     8 */

        /* size: 48, cachelines: 1, members: 3 */
        /* sum members: 44, holes: 1, sum holes: 4 */
        /* last cacheline: 48 bytes */
};

and then tcp_skb_cb,

struct tcp_skb_cb {
	[...]
                struct {
                        __u32      flags;                /*    24     4 */
                        struct sock * sk_redir;          /*    32     8 */
                        void *     data_end;             /*    40     8 */
                } bpf;                                   /*          24 */
        };

So when we use offset_of() to track down the byte offset we get 40 in
either case and everything continues to work. Fix this mess and use
correct structures its unclear how long this might actually work for
until someone moves the structs around.
Reported-by: Martin KaFai Lau <kafai@fb.com>
Fixes: e1ea2f98 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Fixes: 6aaae2b6 ("bpf: rename bpf_compute_data_end into bpf_compute_data_pointers")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Currently, when a sock is closed and the bpf_tcp_close() callback is
used we remove memory but do not free the skb. Call consume_skb() if
the skb is attached to the buffer.

Reported-by: syzbot+d464d2c20c717ef5a6a8@syzkaller.appspotmail.com
Fixes: 1aa12bdf ("bpf: sockmap, add sock close() hook to remove socks")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

After latest lock updates there is no longer anything preventing a
close and recvmsg call running in parallel. Additionally, we can
race update with close if we close a socket and simultaneously update
if via the BPF userspace API (note the cgroup ops are already run
with sock_lock held).

To resolve this take sock_lock in close and update paths.

Reported-by: syzbot+b680e42077a0d7c9a0c4@syzkaller.appspotmail.com
Fixes: e9db4ef6 ("bpf: sockhash fix omitted bucket lock in sock_close")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Multiple BPF helpers in use by sk_skb programs calculate the max
skb length using the __bpf_skb_max_len function. However, this
calculates the max length using the skb->dev pointer which can be
NULL when an sk_skb program is paired with an sk_msg program.

To force this a sk_msg program needs to redirect into the ingress
path of a sock with an attach sk_skb program. Then the the sk_skb
program would need to call one of the helpers that adjust the skb
size.

To fix the null ptr dereference use SKB_MAX_ALLOC size if no dev
is available.

Fixes: 8934ce2f ("bpf: sockmap redirect ingress support")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>