- 12 Jun, 2013 11 commits
-
-
Yijing Wang authored
Fix build error for il_pm_ops if CONFIG_PM is set but CONFIG_PM_SLEEP is not set. ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl4965.ko] undefined! ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl3945.ko] undefined! make[1]: *** [__modpost] Error 1 make: *** [modules] Error 2 Signed-off-by:
Yijing Wang <wangyijing@huawei.com> Cc: Stanislaw Gruszka <sgruszka@redhat.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: netdev@vger.kernel.org Cc: linux-wireless@vger.kernel.org Cc: Jingoo Han <jg1.han@samsung.com> Acked-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
This false leak indication is avoided with a no-leak annotation to kmemleak. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Eliad Peller authored
Due to a typo, the current code copies only sizeof(cmd->channels_2) bytes, which is smaller than the correct sizeof(cmd->channels_5) size, resulting in a partial scan (some channels are skipped). Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
Luciano Coelho <coelho@ti.com> Signed-off-by:
-
Luciano Coelho authored
The minimum firmware version required for singlerole after recent driver changes is 6/7.3.10.0.133. Reported-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Luciano Coelho authored
There was a typo in commit 8675f9 (wlcore/wl12xx/wl18xx: verify multi-role and single-role fw versions), which was causing the multirole firmware for wl127x (WiLink6) to be rejected. The actual minimum version needed for wl127x multirole is 6.5.7.0.42. Reported-by:
Levi Pearson <levipearson@gmail.com> Reported-by:
Michael Scott <hashcode0f@gmail.com> Cc: stable@kernel.org # 3.9+ Signed-off-by:
-
Larry Finger authored
Driver rtl8192cu can connect to WPA2 networks, but fails for any other encryption method. The cause is a failure to set the rate control data blocks. These changes fix https://bugzilla.redhat.com/show_bug.cgi?id=952793 and https://bugzilla.redhat.com/show_bug.cgi?id=761525. Signed-off-by:
-
Mark A. Greer authored
When reading the contents of '/sys/kernel/debug/mwifiex/p2p0/info', the following panic occurs: $ cat /sys/kernel/debug/mwifiex/p2p0/info Unable to handle kernel paging request at virtual address 74706164 pgd = de530000 [74706164] *pgd=00000000 Internal error: Oops: 5 [#1] SMP ARM Modules linked in: phy_twl4030_usb omap2430 musb_hdrc mwifiex_sdio mwifiex CPU: 0 PID: 1635 Comm: cat Not tainted 3.10.0-rc1-00010-g1268390 #1 task: de16b6c0 ti: de048000 task.ti: de048000 PC is at strnlen+0xc/0x4c LR is at string+0x3c/0xf8 pc : [<c02c123c>] lr : [<c02c2d1c>] psr: a0000013 sp : de049e10 ip : c06efba0 fp : de6d2092 r10: bf01a260 r9 : ffffffff r8 : 74706164 r7 : 0000ffff r6 : ffffffff r5 : de6d209c r4 : 00000000 r3 : ff0a0004 r2 : 74706164 r1 : ffffffff r0 : 74706164 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 10c5387d Table: 9e530019 DAC: 00000015 Process cat (pid: 1635, stack limit = 0xde048240) Stack: (0xde049e10 to 0xde04a000) 9e00: de6d2092 00000002 bf01a25e de6d209c 9e20: de049e80 c02c438c 0000000a ff0a0004 ffffffff 00000000 00000000 de049e48 9e40: 00000000 2192df6d ff0a0004 ffffffff 00000000 de6d2092 de049ef8 bef3cc00 9e60: de6b0000 dc358000 de6d2000 00000000 00000003 c02c45a4 bf01790c bf01a254 9e80: 74706164 bf018698 00000000 de59c3c0 de048000 de049f80 00001000 bef3cc00 9ea0: 00000008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9ec0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9ee0: 00000000 00000000 00000000 00000001 00000000 00000000 6669776d 20786569 9f00: 20302e31 2e343128 392e3636 3231702e 00202933 00000000 00000003 c0294898 9f20: 00000000 00000000 00000000 00000000 de59c3c0 c0107c04 de554000 de59c3c0 9f40: 00001000 bef3cc00 de049f80 bef3cc00 de049f80 00000000 00000003 c0108a00 9f60: de048000 de59c3c0 00000000 00000000 de59c3c0 00001000 bef3cc00 c0108b60 9f80: 00000000 00000000 00001000 bef3cc00 00000003 00000003 c0014128 de048000 9fa0: 00000000 c0013f80 00001000 bef3cc00 00000003 bef3cc00 00001000 00000000 9fc0: 00001000 bef3cc00 00000003 00000003 00000001 00000001 00000001 00000003 9fe0: 00000000 bef3cbdc 00011984 b6f1127c 60000010 00000003 18dbdd2c 7f7bfffd [<c02c123c>] (strnlen+0xc/0x4c) from [<c02c2d1c>] (string+0x3c/0xf8) [<c02c2d1c>] (string+0x3c/0xf8) from [<c02c438c>] (vsnprintf+0x1e8/0x3e8) [<c02c438c>] (vsnprintf+0x1e8/0x3e8) from [<c02c45a4>] (sprintf+0x18/0x24) [<c02c45a4>] (sprintf+0x18/0x24) from [<bf01790c>] (mwifiex_info_read+0xfc/0x3e8 [mwifiex]) [<bf01790c>] (mwifiex_info_read+0xfc/0x3e8 [mwifiex]) from [<c0108a00>] (vfs_read+0xb0/0x144) [<c0108a00>] (vfs_read+0xb0/0x144) from [<c0108b60>] (SyS_read+0x44/0x70) [<c0108b60>] (SyS_read+0x44/0x70) from [<c0013f80>] (ret_fast_syscall+0x0/0x30) Code: e12fff1e e3510000 e1a02000 0a00000d (e5d03000) ---[ end trace ca98273dc605a04f ]--- The panic is caused by the mwifiex_info_read() routine assuming that there can only be four modes (0-3) which is an invalid assumption. For example, when testing P2P, the mode is '8' (P2P_CLIENT) so the code accesses data beyond the bounds of the bss_modes[] array which causes the panic. Fix this by updating bss_modes[] to support the current list of modes and adding a check to prevent the out-of-bounds access from occuring in the future when more modes are added. Signed-off-by:
Mark A. Greer <mgreer@animalcreek.com> Acked-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Johan Hedberg authored
If hci_dev_open fails we need to ensure that the corresponding mgmt_set_powered command gets an appropriate response. This patch fixes the missing response by adding a new mgmt_set_powered_failed function that's used to indicate a power on failure to mgmt. Since a situation with the device being rfkilled may require special handling in user space the patch uses a new dedicated mgmt status code for this. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org Acked-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by:
-
Johan Hedberg authored
There has been code in place to check that the L2CAP length header matches the amount of data received, but many PDU handlers have not been checking that the data received actually matches that expected by the specific PDU. This patch adds passing the length header to the specific handler functions and ensures that those functions fail cleanly in the case of an incorrect amount of data. Signed-off-by:
-
Bing Zhao authored
The register offsets have been changed in SD8897 and newer chips. Define a new btmrvl_sdio_card_reg map for SD88xx. Signed-off-by:
Frank Huang <frankh@marvell.com> Signed-off-by:
-
Johan Hedberg authored
LE-only controllers do not support extended features so any kind of host feature bit checks do not make sense for them. This patch fixes code used for both single-mode (LE-only) and dual-mode (BR/EDR/LE) to use the HCI_LE_ENABLED flag instead of the "Host LE supported" feature bit for LE support tests. Signed-off-by:
-
- 28 May, 2013 10 commits
-
-
Gabor Juhos authored
Accessing the OTP memory on AR9950 causes a data bus like this: Data bus error, epc == 801f7774, ra == 801f7774 Oops[#1]: CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.0-rc3 #592 task: 87c28000 ti: 87c22000 task.ti: 87c22000 $ 0 : 00000000 00000061 deadc0de 00000000 $ 4 : b8115f18 00015f18 00000007 00000004 $ 8 : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c $12 : 7c7c3c7c 80320a68 00000000 7c7c7c3c $16 : 87cd8010 00015f18 00000007 00000000 $20 : 00000064 00000004 87c23c7c 8035210c $24 : 00000000 801f3674 $28 : 87c22000 87c23b48 00000001 801f7774 Hi : 00000000 Lo : 00000064 epc : 801f7774 ath9k_hw_wait+0x58/0xb0 Not tainted ra : 801f7774 ath9k_hw_wait+0x58/0xb0 Status: 1000cc03 KERNEL EXL IE Cause : 4080801c PrId : 00019750 (MIPS 74Kc) Modules linked in: Process swapper (pid: 1, threadinfo=87c22000, task=87c28000, ts=00000000) Stack : 0000000f 00000061 00002710 8006240c 00000001 87cd8010 87c23bb0 87cd8010 00000000 00000004 00000003 80210c7c 000000b3 67fa8000 0000032a 000006fe 000003e8 00000002 00000028 87c23bf0 000003ff 80210d24 803e5630 80210e28 00000000 00000007 87cd8010 00007044 00000004 00000061 000003ff 000001ff 87c26000 87cd8010 00000220 87cd8bb8 80210000 8020fcf4 87c22000 87c23c08 ... Call Trace: [<801f7774>] ath9k_hw_wait+0x58/0xb0 [<80210c7c>] ar9300_otp_read_word+0x80/0xd4 [<80210d24>] ar9300_read_otp+0x54/0xb0 [<8020fcf4>] ar9300_check_eeprom_header+0x1c/0x40 [<80210fe4>] ath9k_hw_ar9300_fill_eeprom+0x118/0x39c [<80206650>] ath9k_hw_eeprom_init+0x74/0xb4 [<801f96d0>] ath9k_hw_init+0x7ec/0x96c [<801e65ec>] ath9k_init_device+0x340/0x758 [<801f35d0>] ath_ahb_probe+0x21c/0x2c0 [<801c041c>] driver_probe_device+0xc0/0x1e4 [<801c05ac>] __driver_attach+0x6c/0xa4 [<801bea08>] bus_for_each_dev+0x64/0xa8 [<801bfa40>] bus_add_driver+0xcc/0x24c [<801c0954>] driver_register+0xbc/0x17c [<803f8fc0>] ath9k_init+0x5c/0x88 [<800608fc>] do_one_initcall+0xec/0x1a0 [<803e6a68>] kernel_init_freeable+0x13c/0x200 [<80309cdc>] kernel_init+0x1c/0xe4 [<80062450>] ret_from_kernel_thread+0x10/0x18 On the AR9550, the OTP registers are located at the same address as on the AR9340. Use the correct values to avoid the error. Cc: stable@vger.kernel.org # 3.6+ Signed-off-by:Gabor Juhos <juhosg@openwrt.org> Signed-off-by:
-
Hante Meuleman authored
For p2p client mode powersave mode should be kept disabled. It is working but inefficient. In general p2p links do no benefit from this mode, because these links are setup temporarily to transfer data. Reviewed-by:
Arend Van Spriel <arend@broadcom.com> Signed-off-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
-
Hante Meuleman authored
Multi channel support was disabled. This patch will enable it and configure the P2P GO on the correct frequency when multi channel is used. Reviewed-by:
-
Arend van Spriel authored
Upon deleting a P2P_CLIENT/GO interface the vif and consequently the wdev is freed before the net_device is actually being unregistered but cfg80211 still needs to access the wdev. Using destructor field to free the net_device and vif. Reviewed-by:
-
Arend van Spriel authored
When registration fails the net device is no longer needed. Free the net device and remove reference to private data from the driver. Reviewed-by:
-
Arend van Spriel authored
Pass the struct brcmf_cfg80211_info instance instead of obtaining through vif itself using vif->wdev. This is needed as the netdev associated with this vif is already unregistered. Reviewed-by:
-
Hante Meuleman authored
The firmware requires that on p2p setup when net interfaces are created or updated that they start initially with the same channel as the channel in use for the current connection (if any). If none exists take default channel 11. Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
-
Hante Meuleman authored
ARP offloading should only be used in STA or P2P client mode. It is currently configured once at init. When being configured for AP ARP offloading should be turned off and when AP mode is left it can be turned back on. Cc: stable@vger.kernel.org Reviewed-by:
-
-
-
- 27 May, 2013 4 commits
-
-
Emmanuel Grumbach authored
In 63b77bf4 iwlwifi: dvm: don't send zeroed LQ cmd I tried to avoid to send zeroed LQ cmd, but I made a (very) stupid mistake in the memcmp. Since this patch has been ported to stable, the fix should go to stable too. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341 Cc: stable@vger.kernel.org Reported-by:
Hinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Helmut Schaa authored
When changing the MAC address of a single vif mac80211 will check if the new address fits into the address mask specified by the driver. This only needs to be done when using multiple BSSIDs. Hence, check the new address only against all other vifs. Also fix the MAC address assignment on new interfaces if the user changed the address of a vif such that perm_addr is not covered by addr_mask anymore. Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=57371Signed-off-by:
Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by:
Jakub Kicinski <kubakici@wp.pl> Reported-by:
Alessandro Lannocca <alessandro.lannocca@gmail.com> Cc: Alessandro Lannocca <alessandro.lannocca@gmail.com> Cc: Bruno Randolf <br1@thinktube.com> Signed-off-by:
-
Johannes Berg authored
Since Eric's commit efe117ab ("Speedup ieee80211_remove_interfaces") there's a bug in mac80211 when it unregisters with AP_VLAN interfaces up. If the AP_VLAN interface was registered after the AP it belongs to (which is the typical case) and then we get into this code path, unregister_netdevice_many() will crash because it isn't prepared to deal with interfaces being closed in the middle of it. Exactly this happens though, because we iterate the list, find the AP master this AP_VLAN belongs to and dev_close() the dependent VLANs. After this, unregister_netdevice_many() won't pick up the fact that the AP_VLAN is already down and will do it again, causing a crash. Cc: stable@vger.kernel.org [2.6.33+] Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Johannes Berg authored
A lot of code in mac80211 assumes that the hw queues are set up correctly for all interfaces (except for monitor) but this isn't true for AP_VLAN interfaces. Fix this by copying the AP master configuration when an AP VLAN is brought up, after this the AP interface can't change its configuration any more and needs to be brought down to change it, which also forces AP_VLAN interfaces down, so just copying in open() is sufficient. Reported-by:
Jouni Malinen <j@w1.fi> Signed-off-by:
-
- 24 May, 2013 3 commits
-
-
Felix Fietkau authored
AR934x v1.3 no longer needs the DCU backoff reduction workaround for preventing rx overruns, but in turn needs the number of usable Tx buffers to be reduced slightly. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
If a local bus timeout has been detected, the host interface needs to be reset to clear the errors. AR934x uses a different synchronous interrupt bit to indicate this, so the check needs to be fixed. Signed-off-by:
-
Felix Fietkau authored
Do not subtract spur power from noise floor on this chip, as it can lead to packet loss and other connectivity issues. Signed-off-by:
-
- 23 May, 2013 3 commits
-
-
Felix Fietkau authored
Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag, not NL80211_STA_INFO_TX_BYTES64. Signed-off-by:
-
Johannes Berg authored
The code I added in "mac80211: don't start new netdev queues if driver stopped" crashes for monitor and AP VLAN interfaces because while they have a netdev, they don't have queues set up by the driver. To fix the crash, exclude these from queue accounting here and just start their netdev queues unconditionally. For monitor, this is the best we can do, as we can redirect frames there to any other interface and don't know which one that will since it can be different for each frame. For AP VLAN interfaces, we can do better later and actually properly track the queue status. Not doing this is really a separate bug though. Reported-by:
Ilan Peer <ilan.peer@intel.com> Reported-by:
-
Johannes Berg authored
If a P2P-Device is present and another virtual interface triggers the connection work, the system crash because it tries to check if the P2P-Device's netdev (which doesn't exist) is up. Skip any wdevs that have no netdev to fix this. Cc: stable@vger.kernel.org Reported-by:
YanBo <dreamfly281@gmail.com> Signed-off-by:
-
- 22 May, 2013 3 commits
-
-
Dan Carpenter authored
There was an extra ';' character added to the end of the if statement which means that it always prints that the /proc entry wasn't created even though it was. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Felix Fietkau authored
Waiting for all subframes of an existing aggregation session to drain before allowing mac80211 to start a new one is fragile and deadlocks caused by this behavior have been observed. Since mac80211 has proper synchronization for aggregation session start/stop handling, a better approach to session handling is to simply allow mac80211 to start a new session at any time. This requires changing the code to discard any packets outside of the BlockAck window in the A-MPDU software retry code. This patch implements the above and also simplifies the code. Signed-off-by:
-
John W. Linville authored
"Merge tag 'nfc-fixes-3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-fixes This is the first batch of NFC fixes for 3.10, and it contains: - 3 fixes for the NFC MEI support: * We now depend on the correct Kconfig symbol. * We register an MEI event callback whenever we enable an NFC device, otherwise we fail to read anything after an enable/disable cycle. * We only disable an MEI device from its disable mey_phy_ops, preventing useless consecutive disable calls. - An NFC Makefile cleanup, as I forgot to remove a commented out line when moving the LLCP code to the NFC top level directory." Signed-off-by:
-
- 21 May, 2013 4 commits
-
-
Samuel Ortiz authored
Enabling and disabling device is exclusively handled by the mei_phy_ops. Signed-off-by:Samuel Ortiz <sameo@linux.intel.com>
-
Samuel Ortiz authored
The callback registration starts a waiting read, so it needs to be fired everytime the device is enabled. Otherwise following writes will never get an answer back. Signed-off-by: -
Samuel Ortiz authored
INTEL_MEI_BUS_NFC never made it upstream, so make it depend on INTEL_MEI. Signed-off-by: -
Paul Bolle authored
The Kconfig symbol NFC_LLCP was removed in commit 30cc4587 ("NFC: Move LLCP code to the NFC top level diirectory"). But the reference to its macro in this Makefile was only commented out. Remove it now. Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
- 17 May, 2013 2 commits
-
-
Felix Fietkau authored
After a tx attempt, an A-MPDU subframe can still have fi->retries at 0 (if the retry count wasn't incremented due to powersave). In that case it is still tracked as part of the block ack window, so when draining the tid queue, its sequence number needs to be cleared from the pending frame bitmap. Signed-off-by:
-
Felix Fietkau authored
This patch fixes some issues introduced in the rate control API rework. When not running aggregation, copy bf->rates into info->control.rates before applying the rate control status to it. In ath_lookup_rate, the rates need to be pulled from bf->rates, not the tx info. Signed-off-by:
-
