obj has type struct snmp_object **, not struct snmp_object *.  But indeed
it is not even clear why kmalloc is needed.  The memory is freed by the end
of the function, so the local variable of pointer type should be sufficient.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@

  x =
  <+...sizeof(
- T
+ *x
  )...+>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Patrick McHardy <kaber@trash.net>

axnet_cs:
    remove unnecessary spin_unlock_irqrestore,spin_lock_irqsave.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can rely on kconfig to limit these numbers,
no need to limit them at compile time/run time.

Users who modify these numbers manually should
be responsible for themself. :)
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Per Liden <per.liden@ericsson.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the flag CAN_CTRLMODE_ONE_SHOT. It is used as mask
or flag in the "struct can_ctrlmode".

It allows userspace via netlink to set a CAN controller into the special
"one-shot" mode. In this mode, if supported by the CAN controller, it
tries only once to deliver a CAN frame and aborts it if an error
(e.g.: arbitration lost) happens.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

this patch removes the hlist that contains the CAN receiver filter lists.
It uses the 'midlayer private' pointer ml_priv and links the filters directly
to the CAN netdevice, which allows to omit the walk through the complete CAN
devices hlist for each received CAN frame.

This patch is tested and does not remove any locking.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use kzalloc rather than kcalloc(1,...)

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
@@

- kcalloc(1,
+ kzalloc(
          ...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows a bond device to specify an arp_ip_target as a host that is
not on the same vlan as the base bond device and still use arp
validation.  A configuration like this, now works:

BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3"

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::213:21ff:febe:33e9/64 scope link
       valid_lft forever preferred_lft forever
9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
    inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100
    inet6 fe80::213:21ff:febe:33e9/64 scope link
       valid_lft forever preferred_lft forever

Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 1000
ARP IP target/s (n.n.n.n form): 10.0.100.1

Slave Interface: eth1
MII Status: up
Link Failure Count: 1
Permanent HW addr: 00:40:05:30:ff:30

Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:13:21:be:33:e9
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/libertas/scan.c

Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the %pM kernel extension to display the MAC address.

The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation instead of
space-separated.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 9bd568a5.

That commit is shown to cause allocation failures during initialization
on some machines.

http://bugzilla.kernel.org/show_bug.cgi?id=14844Signed-off-by: John W. Linville <linville@tuxdriver.com>

To make it easier to notice cases of calling sleeping ops in atomic context,
annotate driver-ops.h with appropiate might_sleep() calls. At the same time,
also document in mac80211.h the op functions with missing contexts.

mac80211 doesn't seem to use get_tx_stats anywhere currently. Just to be on
the safe side, I documented it to be atomic, but hopefully the op can be
removed in the future.

Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There's no need to be requeueing the work struct
since we check for the scan after removing items
due to possible timeouts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:

@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When, for instance, a new IBSS peer is found, userspace
wants to be notified. Add events for all new stations
that mac80211 learns about.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This changes mac80211 to allow being off-channel for
any type of work, not just the 'remain-on-channel'
work. This also helps fast transition to a BSS on a
different channel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This implements the new remain-on-channel cfg80211
command in mac80211, extending the work interface.

Also change the work purge code to be able to clean
up events properly (pretending they timed out.)
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add new commands for requesting the driver to remain awake
on a specified channel for the specified amount of time
(and another command to cancel such an operation). This
can be used to implement userspace-controlled off-channel
operations, like Public Action frame exchange on another
channel than the operation channel.

The off-channel operation should behave similarly to scan,
i.e. the local station (if associated) moves into power
save mode to request the AP to buffer frames for it and
then moves to the other channel to allow the off-channel
operation to be completed. The duration parameter can be
used to request enough time to receive a response from
the target station.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The off-channel operations for going into power save mode (station
mode) or stop beaconing (AP/IBSS) are not limited to scanning. Move
these into a separate file and allow them to be used for other
purposes, too.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211 offers private data for each BSS struct,
which mac80211 uses. However, mac80211 uses internal
and external (cfg80211) BSS pointers interchangeably
and has a hack to put the cfg80211 bss struct into
the private struct.

Remove this hack, properly converting between the
pointers wherever necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, we insert all user-specified IEs before the HT
IE for association, and after the HT IE for probe requests.
For association, that's correct only if the user-specified
IEs are RSN only, incorrect in all other cases including
WPA. Change this to split apart the user-specified IEs in
two places for association: before the HT IE (e.g. RSN),
after the HT IE (generally empty right now I think?) and
after WMM (all other vendor-specific IEs). For probes,
split the IEs in different places to be correct according
to the spec.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Refactor the code to reserve an skb of the right size
(instead of hoping 200 bytes are enough forever), and
also put HT IE generation into an own function.

Additionally, put the HT IE before the vendor-specific
WMM IE. This still leaves things not quite ordered
correctly, due to user-specified IEs, add a note about
that for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The station we're authenticating/associating with
may not always be an AP in the sense that word is
mostly understood, so print only the MAC address
of the peer instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In order to use auth/assoc for different purposes
other than MLME, it needs to be split up. For other
purposes, a generic work handling (potentially on
another channel) will be useful.

To achieve that, this patch moves much of the MLME
work handling out of mlme into a new work API. The
API can currently handle probing a specific AP,
authentication and association. The MLME previously
handled probe/authentication as one step and will
continue to do so, but they are separate in the new
work handling.

Work items are RCU-managed to be able to check for
existence of an item for a specific frame in the RX
path, but they can be re-used which the MLME right
now will do for its combined probe/auth step.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As a first step of generalising management work,
this renames a few things and puts more information
directly into the struct so that auth/assoc need
not access the BSS pointer as often -- in fact it
can be removed from auth completely. Also since the
previous patch made sure a new work item is used
for association, we can make the different data a
union.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 currently hangs on to the auth state by
keeping it on the work list. That can lead to
confusing behaviour like rejecting scans while
authenticated to any AP (but not yet associated.)
It also means that it needs to keep track of the
work struct while associated for when it gets
disassociated (or disassociates.)

Change this to free the work struct after the
authentication completed successfully and
allocate a new one for associating, thereby
letting cfg80211 manage the auth state. Another
change necessary for this is to tell cfg80211
about all unicast deauth frames sent to mac80211
since now it can no longer check the auth state,
but that check was racy anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We've long lacked a good confirmation that frames
have really gone out, e.g. before going off-channel
for a scan. Add a flush() operation that drivers
can implement to provide that confirmation, and use
it in a few places:
 * before scanning sends the nullfunc frames
 * after scanning sends the nullfunc frames, if any
 * when going idle, to send any pending frames
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of always using netif_running(sdata->dev)
use ieee80211_sdata_running(sdata) now which is
just an inline containing netif_running() for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is checked in add_interface, but there it is easily replaced with
a check of priv->vif.  If that information should become necessary,
it is available in vif->type anyway.

It is also checked in led_turn_on and led_turn_off, where I made the
substitutions as described above.  Of course, these checks seem to
have been incorrect since the driver was using NL80211_IFTYPE_MONITOR
to indicate no interface rather than NL80211_IFTYPE_UNSPECIFIED.
Anyway, I think these checks may be extraneous...?
Signed-off-by: John W. Linville <linville@tuxdriver.com>