Only exit sdw_handle_slave_status() right after calling
sdw_program_device_num() if it actually programmed an ID into at
least one device.

sdw_handle_slave_status() should protect itself against phantom
device #0 ATTACHED indications. In that case there is no actual
device still on #0. The early exit relies on there being a status
change to ATTACHED on the reprogrammed device to trigger another
call to sdw_handle_slave_status() which will then handle the status
of all peripherals. If no device was actually programmed with an
ID there won't be a new ATTACHED indication. This can lead to the
status of other peripherals not being handled.

The status passed to sdw_handle_slave_status() is obviously always
from a point of time in the past, and may indicate accumulated
unhandled events (depending how the bus manager operates). It's
possible that a device ID is reprogrammed but the last PING status
captured state just before that, when it was still reporting on
ID #0. Then sdw_handle_slave_status() is called with this PING info,
just before a new PING status is available showing it now on its new
ID. So sdw_handle_slave_status() will receive a phantom report of a
device on #0, but it will not find one.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220914160248.1047627-6-rf@opensource.cirrus.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The correct way to handle interrupts is to clear the bits we
are about to handle _before_ handling them. Thus if the condition
then re-asserts during the handling we won't lose it.

This patch changes cdns_update_slave_status_work() to do this.

The previous code cleared the interrupts after handling them.
The problem with this is that when handling enumeration of devices
the ATTACH statuses can be accidentally cleared and so some or all
of the devices never complete their enumeration.

Thus we can have a situation like this:
- one or more devices are reverting to ID #0

- accumulated status bits indicate some devices attached and some
  on ID #0. (Remember: status bits are sticky until they are handled)

- Because of device on #0 sdw_handle_slave_status() programs the
  device ID and exits without handling the other status, expecting
  to get an ATTACHED from this reprogrammed device.

- The device immediately starts reporting ATTACHED in PINGs, which
  will assert its CDNS_MCP_SLAVE_INTSTAT_ATTACHED bit.

- cdns_update_slave_status_work() clears INTSTAT0/1. If the initial
  status had CDNS_MCP_SLAVE_INTSTAT_ATTACHED bit set it will be
  cleared.

- The ATTACHED change for the device has now been lost.

- cdns_update_slave_status_work() clears CDNS_MCP_INT_SLAVE_MASK so
  if the new ATTACHED state had set it, it will be cleared without
  ever having been handled.

Unless there is some other state change from another device to cause
a new interrupt, the ATTACHED state of the reprogrammed device will
never cause an interrupt so its enumeration will not be completed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220914160248.1047627-5-rf@opensource.cirrus.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Don't re-enumerate a peripheral on #0 until we have seen and
handled an UNATTACHED notification for that peripheral.

Without this, it is possible for the UNATTACHED status to be missed
and so the slave->status remains at ATTACHED. If slave->status never
changes to UNATTACHED the child driver will never be notified of the
UNATTACH, and the code in sdw_handle_slave_status() will skip the
second part of enumeration because the slave->status has not changed.

This scenario can happen because PINGs are handled in a workqueue
function which is working from a snapshot of an old PING, and there
is no guarantee when this function will run.

A peripheral could report attached in the PING being handled by
sdw_handle_slave_status(), but has since reverted to device #0 and is
then found in the loop in sdw_program_device_num(). Previously the
code would not have updated slave->status to UNATTACHED because it had
not yet handled a PING where that peripheral had UNATTACHED.

This situation happens fairly frequently with multiple peripherals on
a bus that are intentionally reset (for example after downloading
firmware).
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220914160248.1047627-4-rf@opensource.cirrus.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Ensure that if sdw_handle_slave_status() sees a peripheral
has dropped off the bus it reports it to the client driver.

If there are any devices reporting on address 0 it bails out
after programming the device IDs. So it never reaches the second
loop that calls sdw_update_slave_status().

If the missing device is one that is now showing as unenumerated
it has been given a device ID so will report as attached next
time sdw_handle_slave_status() runs.

With the previous code the client driver would only see another
ATTACHED notification because the UNATTACHED state was lost when
sdw_handle_slave_status() bailed out after programming the
device ID.

This shows up most when the peripheral has to be reset after
downloading updated firmware and there are multiple of these
peripherals on the bus. They will all return to unenumerated state
after the reset, and then there is a mix of unattached, attached
and unenumerated PING states from the peripherals, as each is reset
and they reboot.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220914160248.1047627-3-rf@opensource.cirrus.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The cadence IP explicitly reports slave status changes with bits for
each possible change. The function cdns_update_slave_status() attempts
to translate this into the current status of each of the slaves.

However when there are multiple peripherals on a bus any slave that did
not have a status change when the work function ran would not have it's
status updated - the array is initialised to a value that equates to
UNATTACHED and this can cause spurious reports that slaves had dropped
off the bus.

In the case where a slave has no status change or has multiple status
changes the value from the last PING command is used.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220914160248.1047627-2-rf@opensource.cirrus.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Regroup offset and bitfield definitions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-12-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Regroup offset and bitfield definitions
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-11-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Regroup offset and bitfield definitions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-10-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Regroup offset and bitfield definitions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-9-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Regroup offset and bitfields
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-8-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

add comment and newline to mark out control stream capabilities and
chmap. These registers are unused by the driver, only dumped in
debugfs.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-7-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

We removed PDM support a long time ago but kept the definitions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-6-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Regroup offset and bitfields, no functionality change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-5-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

This read-only register only defines an offset which is known already
and a version which isn't used.

Remove unused definition.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-4-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

No functionality change, just regroup offset and bitfield definitions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-3-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Add definition in header file rather than hidden in code.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823053846.2684635-2-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The allowed values for SoundWire device numbers are between 1 and 11
(inclusive). HDaudio/iDISP codecs typically use SDI values 0..3
(inclusive). To allow for a unique peripheral SDI/dev_number across
HDaudio and SoundWire buses, we set the minimum base to 4. This still
allows for 8 SoundWire peripherals in the system, currently more than
needed in actual products.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823045004.2670658-4-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The SoundWire specification allows the device number to be allocated
at will. When a system includes multiple SoundWire links, the device
number scope is limited to the link to which the device is attached.

However, for integration/debug it can be convenient to have a unique
device number across the system. This patch adds a 'dev_num_ida_min'
field at the bus level, which when set will be used to allocate an
IDA.

The allocation happens when a hardware device reports as ATTACHED. If
any error happens during the enumeration, the allocated IDA is not
freed - the device number will be reused if/when the device re-joins
the bus. The IDA is only freed when the Linux device is unregistered.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823045004.2670658-3-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

To avoid confusions with follow-up patches using a IDA mechanism for
peripheral 'device number' allocation, rename sdw_ida as sdw_bus_ida.

Pure rename, no functionality change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823045004.2670658-2-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823050158.2671245-3-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823050158.2671245-2-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The DSDT for this device has a number of problems:
a) it lists rt711 on link0 and link1, but link1 is disabled
b) the rt711 entry on link0 uses the wrong v2 instead of v3 (SDCA)
c) the rt1316 amplifier on link3 is not listed.

Add a remapping table to work-around these BIOS shenanigans.

BugLink: https://github.com/thesofproject/sof/issues/5955Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220823030919.2346629-1-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The capabilities enabled for multi-link are required as part of the
programming sequences, even when a stream uses a single link we still
use the syncArm/syncGo sequences. Therefore the TODO is no longer
necessary.
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Link: https://lore.kernel.org/r/20220817074859.4759-1-khalid.masum.92@gmail.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Update error prints to debug prints to avoid redundant logging in kernel
boot time, as these prints are informative prints in irq handler.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/1657724067-19004-1-git-send-email-quic_srivasam@quicinc.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.

Fixes powerpc allmodconfig build:

   In file included from include/linux/nodemask.h:97,
                    from include/linux/mmzone.h:17,
                    from include/linux/gfp.h:7,
                    from include/linux/radix-tree.h:12,
                    from include/linux/idr.h:15,
                    from include/linux/kernfs.h:12,
                    from include/linux/sysfs.h:16,
                    from include/linux/kobject.h:20,
                    from include/linux/pci.h:35,
                    from arch/powerpc/kernel/prom_init.c:24:
   include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
      25 |         add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
         |                                              ^~~~~~~~~~~~~~
         |                                              add_latent_entropy
   include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull vfs lseek fix from Al Viro:
 "Fix proc_reg_llseek() breakage. Always had been possible if somebody
  left NULL ->proc_lseek, became a practical issue now"

* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  take care to handle NULL ->proc_lseek()

Easily done now, just by clearing FMODE_LSEEK in ->f_mode
during proc_reg_open() for such entries.

Fixes: 868941b1 "fs: remove no_llseek"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull more xen updates from Juergen Gross:

 - fix the handling of the "persistent grants" feature negotiation
   between Xen blkfront and Xen blkback drivers

 - a cleanup of xen.config and adding xen.config to Xen section in
   MAINTAINERS

 - support HVMOP_set_evtchn_upcall_vector, which is more compliant to
   "normal" interrupt handling than the global callback used up to now

 - further small cleanups

* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
  xen: remove XEN_SCRUB_PAGES in xen.config
  xen/pciback: Fix comment typo
  xen/xenbus: fix return type in xenbus_file_read()
  xen-blkfront: Apply 'feature_persistent' parameter when connect
  xen-blkback: Apply 'feature_persistent' parameter when connect
  xen-blkback: fix persistent grants negotiation
  x86/xen: Add support for HVMOP_set_evtchn_upcall_vector

Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull more perf tool updates from Arnaldo Carvalho de Melo:

 - 'perf c2c' now supports ARM64, adjust its output to cope with
   differences with what is in x86_64. Now go find false sharing on
   ARM64 (at least Neoverse) as well!

 - Refactor the JSON processing, making the output more compact and thus
   reducing the size of the resulting perf binary

 - Improvements for 'perf offcpu' profiling, including tracking child
   processes

 - Update Intel JSON metrics and events files for broadwellde,
   broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown,
   knightslanding, sapphirerapids, skylakex and snowridgex

 - Add 'perf stat' JSON output and a 'perf test' entry for it

 - Ignore memfd and anonymous mmap events if jitdump present

 - Refactor 'perf test' shell tests allowing subdirs

 - Fix an error handling path in 'parse_perf_probe_command()'

 - Fixes for the guest Intel PT tracing patchkit in the 1st batch of
   this merge window

 - Print debuginfod queries if -v option is used, to explain delays in
   processing when debuginfo servers are enabled to fetch DSOs with
   richer symbol tables

 - Improve error message for 'perf record -p not_existing_pid'

 - Fix openssl and libbpf feature detection

 - Add PMU pai_crypto event description for IBM z16 on 'perf list'

 - Fix typos and duplicated words on comments in various places

* tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits)
  perf test: Refactor shell tests allowing subdirs
  perf vendor events: Update events for snowridgex
  perf vendor events: Update events and metrics for skylakex
  perf vendor events: Update metrics for sapphirerapids
  perf vendor events: Update events for knightslanding
  perf vendor events: Update metrics for jaketown
  perf vendor events: Update metrics for ivytown
  perf vendor events: Update events and metrics for icelakex
  perf vendor events: Update events and metrics for haswellx
  perf vendor events: Update events and metrics for cascadelakex
  perf vendor events: Update events and metrics for broadwellx
  perf vendor events: Update metrics for broadwellde
  perf jevents: Fold strings optimization
  perf jevents: Compress the pmu_events_table
  perf metrics: Copy entire pmu_event in find metric
  perf pmu-events: Hide the pmu_events
  perf pmu-events: Don't assume pmu_event is an array
  perf pmu-events: Move test events/metrics to JSON
  perf test: Use full metric resolution
  perf pmu-events: Hide pmu_events_map
  ...

Pull powerpc fixes from Michael Ellerman:

 - Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit
   CPUs trap on it rather than ignoring it as they should.

 - Fix ftrace when building with clang, which was broken by some
   refactoring.

 - A couple of other minor fixes.

Thanks to Christophe Leroy, Naveen N.  Rao, Nick Desaulniers, Ondrej
Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool.

* tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kexec: Fix build failure from uninitialised variable
  powerpc/ppc-opcode: Fix PPC_RAW_TW()
  powerpc64/ftrace: Fix ftrace for clang builds
  powerpc: Make eh value more explicit when using lwarx
  powerpc: Don't hide eh field of lwarx behind a macro
  powerpc: Fix eh field when calling lwarx on PPC32

Pull /proc/mounts fix from Al Viro:
 "Fix for /proc/mounts escaping - escape the '#' character too"

* tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  vfs: escape hash as well

Pull more cifs updates from Steve French:

 - two fixes for stable, one for a lock length miscalculation, and
   another fixes a lease break timeout bug

 - improvement to handle leases, allows the close timeout to be
   configured more safely

 - five restructuring/cleanup patches

* tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Do not access tcon->cfids->cfid directly from is_path_accessible
  cifs: Add constructor/destructors for tcon->cfid
  SMB3: fix lease break timeout when multiple deferred close handles for the same file.
  smb3: allow deferred close timeout to be configurable
  cifs: Do not use tcon->cfid directly, use the cfid we get from open_cached_dir
  cifs: Move cached-dir functions into a separate file
  cifs: Remove {cifs,nfs}_fscache_release_page()
  cifs: fix lock length calculation

Enable multipage folio support for the afs filesystem.

Support has already been implemented in netfslib, fscache and cachefiles
and in most of afs, but I've waited for Matthew Wilcox's latest folio
changes.

Note that it does require a change to afs_write_begin() to return the
correct subpage.  This is a "temporary" change as we're working on
getting rid of the need for ->write_begin() and ->write_end()
completely, at least as far as network filesystems are concerned - but
it doesn't prevent afs from making use of the capability.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Tested-by: kafs-testing@auristor.com
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/lkml/2274528.1645833226@warthog.procyon.org.uk/Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Ingo Molnar:
 "Misc timer fixes:

   - fix a potential use-after-free bug in posix timers

   - correct a prototype

   - address a build warning"

* tag 'timers-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-cpu-timers: Cleanup CPU timers before freeing them during exec
  time: Correct the prototype of ns_to_kernel_old_timeval and ns_to_timespec64
  posix-timers: Make do_clock_gettime() static

Pull x86 fix from Ingo Molnar:
 "Fix the 'IBPB mitigated RETBleed' mode of operation on AMD CPUs (not
  turned on by default), which also need STIBP enabled (if available) to
  be '100% safe' on even the shortest speculation windows"

* tag 'x86-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/bugs: Enable STIBP for IBPB mitigated RETBleed

Pull more i2c updates from Wolfram Sang:

 - two driver fixes for issues introduced this cycle

 - one trivial driver improvement regarding ACPI

 - more DTS conversion and additions

 - documentation updates

 - subsystem-wide move from strlcpy to strscpy

* tag 'i2c-for-5.20-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  docs: i2c: i2c-sysfs: fix hyperlinks
  docs: i2c: i2c-sysfs: improve wording
  docs: i2c: instantiating-devices: add syntax coloring to dts and C blocks
  docs: i2c: smbus-protocol: improve DataLow/DataHigh definition
  docs: i2c: i2c-protocol: remove unused legend items
  docs: i2c: i2c-protocol,smbus-protocol: remove nonsense words
  docs: i2c: i2c-protocol: update introductory paragraph
  i2c: move core from strlcpy to strscpy
  i2c: move drivers from strlcpy to strscpy
  i2c: kempld: Support ACPI I2C device declaration
  i2c: mediatek: add i2c compatible for MT8188
  dt-bindings: i2c: update bindings for mt8188 soc
  i2c: microchip-corei2c: fix erroneous late ack send
  dt-bindings: i2c: qcom,i2c-cci: convert to dtschema
  i2c: qcom-geni: Fix GPI DMA buffer sync-back

Pull NTB updates from Jon Mason:
 "Non-Transparent Bridge updates.

  Fix of heap data and clang warnings, support for a new Intel NTB
  device, and NTB EndPoint Function (EPF) support and the various fixes
  for that"

* tag 'ntb-5.20' of https://github.com/jonmason/ntb:
  MAINTAINERS: add PCI Endpoint NTB drivers to NTB files
  NTB: EPF: Tidy up some bounds checks
  NTB: EPF: Fix error code in epf_ntb_bind()
  PCI: endpoint: pci-epf-vntb: reduce several globals to statics
  PCI: endpoint: pci-epf-vntb: fix error handle in epf_ntb_mw_bar_init()
  PCI: endpoint: Fix Kconfig dependency
  NTB: EPF: set pointer addr to null using NULL rather than 0
  Documentation: PCI: extend subheading underline for "lspci output" section
  Documentation: PCI: Use code-block block for scratchpad registers diagram
  Documentation: PCI: Add specification for the PCI vNTB function device
  PCI: endpoint: Support NTB transfer between RC and EP
  NTB: epf: Allow more flexibility in the memory BAR map method
  PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address
  ntb: intel: add GNR support for Intel PCIe gen5 NTB
  NTB: ntb_tool: uninitialized heap data in tool_fn_write()
  ntb: idt: fix clang -Wformat warnings

Pull more xfs updates from Darrick Wong:
 "There's not a lot this time around, just the usual bug fixes and
  corrections for missing error returns.

   - Return error codes from block device flushes to userspace

   - Fix a deadlock between reclaim and mount time quotacheck

   - Fix an unnecessary ENOSPC return when doing COW on a filesystem
     with severe free space fragmentation

   - Fix a miscalculation in the transaction reservation computations
     for file removal operations"

* tag 'xfs-5.20-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix inode reservation space for removing transaction
  xfs: Fix false ENOSPC when performing direct write on a delalloc extent in cow fork
  xfs: fix intermittent hang during quotacheck
  xfs: check return codes when flushing block devices

Pull more SCSI updates from James Bottomley:
 "Mostly small bug fixes and trivial updates.

  The major new core update is a change to the way device, target and
  host reference counting is done to try to make it more robust (this
  change has soaked for a while to try to winkle out any bugs)"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: pm8001: Fix typo 'the the' in comment
  scsi: megaraid_sas: Remove redundant variable cmd_type
  scsi: FlashPoint: Remove redundant variable bm_int_st
  scsi: zfcp: Fix missing auto port scan and thus missing target ports
  scsi: core: Call blk_mq_free_tag_set() earlier
  scsi: core: Simplify LLD module reference counting
  scsi: core: Make sure that hosts outlive targets
  scsi: core: Make sure that targets outlive devices
  scsi: ufs: ufs-pci: Correct check for RESET DSM
  scsi: target: core: De-RCU of se_lun and se_lun acl
  scsi: target: core: Fix race during ACL removal
  scsi: ufs: core: Correct ufshcd_shutdown() flow
  scsi: ufs: core: Increase the maximum data buffer size
  scsi: lpfc: Check the return value of alloc_workqueue()