Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a result,
using these directives in code sections can result in misaligned data
words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to assume that
fundamental types of word size or above are word- aligned when
accessing them from C.  If the data is not really word-aligned, this
can cause impaired performance and stray alignment faults in some
circumstances.

In general, the following rules should be applied when using data word
declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The 32-bit conditional branches in Thumb-2 have a shorter range
(+/-512K) than their ARM counterparts (+/-32MB).  The linker does
not currently generate trampolines to extend the range of these
Thumb-2 conditional branches, resulting in link errors when vmlinux
is sufficiently large, e.g.:

head.o:(.text+0x464): relocation truncated to fit: R_ARM_THM_JUMP19

This patch forces the longer-range, unconditional branch encoding
by use of an explicit IT instruction.  The resulting branches are
triggered on the same conditions as before.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The code which makes up the zImage header intends to leave a
32-byte gap followed by a branch to the real entry point, a magic
number, and a word containing the absolute entry point address.

This gets messed up with with CONFIG_THUMB2_KERNEL, because the
size of the initial padding NOPs changes.

Instead, the header can be made fully compatible by restoring it to
ARM.

In the Thumb-2 case, we can replace the initial NOPs with a
sequence which switches to Thumb and jumps to the real entry point.

As a consequence, the zImage entry point is now always ARM, so no
special magic is needed any more for the uImage rules in the
Thumb-2 case.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Some instruction operand combinations are used here which are nor
permitted in Thumb-2.

In particular, most uses of pc as an operand are disallowed in
Thumb-2, and deprecated in ARM from ARMv7 onwards.

The modified code introduced by this patch should be compatible
with all architecture versions >= v3, with or without
CONFIG_THUMB2_KERNEL.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C.  If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.

In general, the following rules should be applied when using data
word declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.

In this specific case, we can achieve the desired alignment by
forcing a 32-bit branch instruction using the W() macro, since the
assembler location counter is already 32-bit aligned in this case.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C.  If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.

In general, the following rules should be applied when using data
word declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C.  If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.

In general, the following rules should be applied when using data
word declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C.  If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.

In general, the following rules should be applied when using data
word declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C.  If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.

In general, the following rules should be applied when using data
word declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This change limits number of GIC-originating interrupts to the
platform maximum (defined by NR_IRQS) while still initialising
all distributor registers.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Use call_rcu_sched() for pagetables

PowerPC relies on IRQ-disable to guard against RCU quiecent states,
use the appropriate RCU call version.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This reverts commit e0fdace1.

On-list discussion seems to suggest that the robustness fixes for printk
make this unnecessary and DaveM has also agreed in person at Kernel Summit
and on list.

The main problem with this code is once we hit a lockdep splat we always
keep oops_in_progress set, the console layer uses oops_in_progress with KMS
to decide when it should be showing the oops and not showing X, so it causes
problems around suspend/resume time when a userspace resume can cause a console
switch away from X, only if oops_in_progress is set (which is what we want
if an oops actually is in progress, but not because we had a lockdep splat
2 days prior).

Cc: David S Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  tpm: Autodetect itpm devices

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
  af_unix: limit recursion level
  pch_gbe driver: The wrong of initializer entry
  pch_gbe dreiver: chang author
  ucc_geth: fix ucc halt problem in half duplex mode
  inet: Fix __inet_inherit_port() to correctly increment bsockets and num_owners
  ehea: Add some info messages and fix an issue
  hso: fix disable_net
  NET: wan/x25_asy, move lapb_unregister to x25_asy_close_tty
  cxgb4vf: fix setting unicast/multicast addresses ...
  net, ppp: Report correct error code if unit allocation failed
  DECnet: don't leak uninitialized stack byte
  au1000_eth: fix invalid address accessing the MAC enable register
  dccp: fix error in updating the GAR
  tcp: restrict net.ipv4.tcp_adv_win_scale (#20312)
  netns: Don't leak others' openreq-s in proc
  Net: ceph: Makefile: Remove unnessary code
  vhost/net: fix rcu check usage
  econet: fix CVE-2010-3848
  econet: fix CVE-2010-3850
  econet: disallow NULL remote addr for sendmsg(), fixes CVE-2010-3849
  ...

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  OMAP2+: PM/serial: hold console semaphore while OMAP UARTs are disabled
  OMAP: UART: don't resume UARTs that are not enabled.

Some Lenovos have TPMs that require a quirk to function correctly. This can
be autodetected by checking whether the device has a _HID of INTC0102. This
is an invalid PNPid, and as such is discarded by the pnp layer - however
it's still present in the ACPI code, so we can pull it out that way. This
means that the quirk won't be automatically applied on non-ACPI systems,
but without ACPI we don't have any way to identify the chip anyway so I
don't think that's a great concern.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: James Morris <jmorris@namei.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (24 commits)
  Btrfs: don't use migrate page without CONFIG_MIGRATION
  Btrfs: deal with DIO bios that span more than one ordered extent
  Btrfs: setup blank root and fs_info for mount time
  Btrfs: fix fiemap
  Btrfs - fix race between btrfs_get_sb() and umount
  Btrfs: update inode ctime when using links
  Btrfs: make sure new inode size is ok in fallocate
  Btrfs: fix typo in fallocate to make it honor actual size
  Btrfs: avoid NULL pointer deref in try_release_extent_buffer
  Btrfs: make btrfs_add_nondir take parent inode as an argument
  Btrfs: hold i_mutex when calling btrfs_log_dentry_safe
  Btrfs: use dget_parent where we can UPDATED
  Btrfs: fix more ESTALE problems with NFS
  Btrfs: handle NFS lookups properly
  btrfs: make 1-bit signed fileds unsigned
  btrfs: Show device attr correctly for symlinks
  btrfs: Set file size correctly in file clone
  btrfs: Check if dest_offset is block-size aligned before cloning file
  Btrfs: handle the space_cache option properly
  btrfs: Fix early enospc because 'unused' calculated with wrong sign.
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  EDAC: Fix typos in Documentation/edac.txt
  EDAC, MCE: Fix edac_init_mce_inject error handling
  EDAC: Remove deprecated kbuild goal definitions

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
  GFS2: Userland expects quota limit/warn/usage in 512b blocks

Its easy to eat all kernel memory and trigger NMI watchdog, using an
exploit program that queues unix sockets on top of others.

lkml ref : http://lkml.org/lkml/2010/11/25/8

This mechanism is used in applications, one choice we have is to have a
recursion limit.

Other limits might be needed as well (if we queue other types of files),
since the passfd mechanism is currently limited by socket receive queue
sizes only.

Add a recursion_level to unix socket, allowing up to 4 levels.

Each time we send an unix socket through sendfd mechanism, we copy its
recursion level (plus one) to receiver. This recursion level is cleared
when socket receive queue is emptied.
Reported-by: Марк Коренберг <socketpair@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The wrong of initializer entry was modified.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver's AUTHOR was changed to "Toshiharu Okada" from "Masayuki Ohtake".
I update the Kconfig, renamed "Topcliff" to "EG20T".
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes compile error
Signed-off-by: Chris Mason <chris.mason@oracle.com>

In commit 58933c64(ucc_geth: Fix the wrong the Rx/Tx FIFO size),
the UCC_GETH_UTFTT_INIT is set to 512 based on the recommendation
of the QE Reference Manual.  But that will sometimes cause tx halt
while working in half duplex mode.

According to errata draft QE_GENERAL-A003(High Tx Virtual FIFO
threshold size can cause UCC to halt), setting UTFTT less than
[(UTFS x (M - 8)/M) - 128] will prevent this from happening
(M is the minimum buffer size).

The patch changes UTFTT back to 256.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Jean-Denis Boyer <jdboyer@media5corp.com>
Cc: Andreas Schmitz <Andreas.Schmitz@riedel.net>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet sockets corresponding to passive connections are added to the bind hash
using ___inet_inherit_port(). These sockets are later removed from the bind
hash using __inet_put_port(). These two functions are not exactly symmetrical.
__inet_put_port() decrements hashinfo->bsockets and tb->num_owners, whereas
___inet_inherit_port() does not increment them. This results in both of these
going to -ve values.

This patch fixes this by calling inet_bind_hash() from ___inet_inherit_port(),
which does the right thing.

'bsockets' and 'num_owners' were introduced by commit a9d8f911
(inet: Allowing more than 64k connections and heavily optimize bind(0))
Signed-off-by: Nagendra Singh Tomar <tomer_iisc@yahoo.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds some debug information about ehea not being able to
allocate enough spaces. Also it correctly updates the amount of available
skb.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new DIO bio splitting code has problems when the bio
spans more than one ordered extent.  This will happen as the
generic DIO code merges our get_blocks calls together into
a bigger single bio.

This fixes things by walking forward in the ordered extent
code finding all the overlapping ordered extents and completing them
all at once.
Signed-off-by: Chris Mason <chris.mason@oracle.com>

This avoids some include-file hell, and the function isn't really
important enough to be inlined anyway.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

And in particular, use it in 'pipe_fcntl()'.

The other pipe functions do not need to use the 'careful' version, since
they are only ever called for things that are already known to be pipes.

The normal read/write/ioctl functions are called through the file
operations structures, so if a file isn't a pipe, they'd never get
called.  But pipe_fcntl() is special, and called directly from the
generic fcntl code, and needs to use the same careful function that the
splice code is using.

Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

.. and change it to take the 'file' pointer instead of an inode, since
that's what all users want anyway.

The renaming is preparatory to exporting it to other users.  The old
'pipe_info()' name was too generic and is already used elsewhere, so
before making the function public we need to use a more specific name.

Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf: Fix the software context switch counter
  perf, x86: Fixup Kconfig deps
  x86, perf, nmi: Disable perf if counters are not accessible
  perf: Fix inherit vs. context rotation bug

* 'fwnet' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: net: throttle TX queue before running out of tlabels
  firewire: net: replace lists by counters
  firewire: net: fix memory leaks
  firewire: net: count stats.tx_packets and stats.tx_bytes

The HSO driver incorrectly creates a serial device instead of a net
device when disable_net is set. It shouldn't create anything for the
network interface.
Signed-off-by: Filip Aben <f.aben@option.com>
Reported-by: Piotr Isajew <pki@ex.com.pl>
Reported-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We register lapb when tty is created, but unregister it only when the
device is UP. So move the lapb_unregister to x25_asy_close_tty after
the device is down.

The old behaviour causes ldisc switching to fail each second attempt,
because we noted for us that the device is unused, so we use it the
second time, but labp layer still have it registered, so it fails
obviously.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Sergey Lapin <slapin@ossfans.org>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Tested-by: Mikhail Ulyanov <ulyanov.mikhail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We were truncating the number of unicast and multicast MAC addresses
supported.  Additionally, we were incorrectly computing the MAC Address
hash (a "1 << N" where we needed a "1ULL << N").
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocating unit from ird might return several error codes
not only -EAGAIN, so it should not be changed and returned
precisely. Same time unit release procedure should be invoked
only if device is unregistering.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

A single uninitialized padding byte is leaked to userspace.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

"aup->enable" holds already the address pointing to the MAC enable
register. The bug was introduced by commit d0e7cb:

"au1000-eth: remove volatiles, switch to I/O accessors".

CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>