Convert logging messages to more current styles.

Added -DDEBUG to Makefile to maintain current message logging.
This could be converted to a specific CONFIG_TULIP_DEBUG option.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the current more descriptive logging styles.

Add pr_fmt and remove PFX where appropriate.
Use netif_<level>, netdev_<level>
Indent a few blocks in xircom_cb where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the blocks that are guarded by #if DEBUG to
be #if defined DEBUG && DEBUG > 1 so that pr_debug
can be used later.

Remove enter/leave macros and uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mac_pton() parses MAC address in form XX:XX:XX:XX:XX:XX and only in that form.

mac_pton() doesn't dirty result until it's sure string representation is valid.

mac_pton() doesn't care about characters _after_ last octet,
it's up to caller to deal with it.

mac_pton() diverges from 0/-E return value convention.
Target usage:

	if (!mac_pton(str, whatever->mac))
		return -EINVAL;
	/* ->mac being u8 [ETH_ALEN] is filled at this point. */
	/* optionally check str[3 * ETH_ALEN - 1] for termination */

Use mac_pton() in pktgen and netconsole for start.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull read_lock(&bond->lock) and BOND_IS_OK() to bond_start_xmit() from
mode-dependent xmit functions.

netif_running() is always true in hard_start_xmit.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unknown 8168 chips did not have any PLL power method set as they
did not inherit a default family soon enough. Fix it.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

- RTL_GIGA_MAC_NONE is a fake index so put it at the end of the
  enumeration and shift everybody.
- RTL_GIGA_MAC_VER_17 / RTL_GIGA_MAC_VER_16 ordering fixed. Though
  not wrong it was confusing enough to wonder if things were right.

Renaming rtl_chip_info was not strictly necessary. It allows to
check the patch for the correct use of the indexes though.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

There is no real firmware version yet but the manpage of ethtool
is rather terse about the driver information.

Former output:
$ ethtool -i eth1
driver: r8169
version: 2.3LK-NAPI
firmware-version:
bus-info: 0000:01:00.0
$ ethtool -i eth0
driver: r8169
version: 2.3LK-NAPI
firmware-version:
bus-info: 0000:03:00.0

Current output:
$ ethtool -i eth1
driver: r8169
version: 2.3LK-NAPI
firmware-version: N/A
bus-info: 0000:01:00.0

$ ethtool -i eth0
driver: r8169
version: 2.3LK-NAPI
firmware-version: rtl_nic/rtl8168d-1.fw
bus-info: 0000:03:00.0
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by Ciprian Docan <docan@eden.rutgers.edu>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Fejes József <fejes@joco.name>
Cc: Borislav Petkov <borislav.petkov@amd.com>

Invocation of rtl8169_rx_interrupt from rtl8169_reset_task was originally
intended to retrieve as much packets as possible from the rx ring when a
reset was needed. Nowadays rtl8169_reset_task is only scheduled, with
some delay
a. from the tx timeout watchdog
b. when resuming
c. from rtl8169_rx_interrupt itself

It's dubious that the loss of outdated packets will matter much for a)
and b). c) does not need to call itself again.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

The implementation was a bit krusty.

The 10s rtl8169_phy_timer timer has been (was ?) required with older
8169 for adequate phy operation when full gigabit is advertised in
autonegotiated mode. The timer does nothing if the link is up.
Otherwise it keeps resetting the phy until things improve.

- the device private data field phy_1000_ctrl_reg was used to
  schedule the timer. Avoid it and save a few bytes.

- rtl8169_set_settings
  pending timer is disabled before changing the link settings as
  rtl8169_phy_timer is not always needed (see the removed test in
  rtl8169_phy_timer).

- rtl8169_set_speed
  the requested link parameters may not match the chipset : bail out
  early on failure.

- rtl8169_open
  Calling rtl8169_request_timer is redundant with
  -> rtl8169_open
     -> rtl8169_init_phy
        -> rtl8169_set_speed
           -> mod_timer
  The latter always enables the phy timer whereas the former did not
  for RTL_GIGA_MAC_VER_01. It should not make things worse but only
  time will tell if reality agrees.

- rtl8169_request_timer : unused yet. Removed.

- rtl8169_delete_timer : useless. Bloat. Removed.

Side effect : the timer may kick in if the TBI is enabled. I do not
know if the TBI has ever been used in real life.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

Shorten chipset version test.

No functional change.

Careful readers will notice that the 'supports_gmii' flag is deduced
from the device PCI id. Though less specific than the chipset related
RTL_GIGA_MAC_VER_XY, it is good enough to detect a GMII deprieved 810x.
Some features push for a device specific configuration (improved jumbo
frame support for instance). 'supports_gmii' will follow this path
if / when the device PCI id test stops working.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>

At VLAN dismantle phase, unregister_vlan_dev() makes one
synchronize_net() call after vlan_group_set_device(grp, vlan_id, NULL).

This call can be safely removed because we are calling
unregister_netdevice_queue() to queue device for deletion, and this
process needs at least one rcu grace period to complete.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Speedup vlan dismantling in CONFIG_VLAN_8021Q_GVRP=y cases,
by using a call_rcu() to free the memory instead of waiting with
expensive synchronize_rcu() [ while RTNL is held ]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

veth devices dont use the batched device unregisters yet.

Since veth are a pair of devices, it makes sense to use a batch of two
unregisters, this roughly divides dismantle time by two.

Fix this by changing dellink() callers to always provide a non NULL
head. (Idea from Michał Mirosław)

This patch also handles macvlan case : We now dismantle all macvlans on
top of a lower dev at once.
Reported-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I messed things up when I converted over to the transport
flow, I passed the ipv4 address value instead of it's address.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This way rt->rt_dst accesses are unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>

This way ip_output.c no longer needs rt->rt_{src,dst}.

We already have these keys sitting, ready and waiting, on the stack or
in a socket structure.
Signed-off-by: David S. Miller <davem@davemloft.net>

We have two cases.

Either the socket is in TCP_ESTABLISHED state and connect() filled
in the inet socket cork flow, or we looked up the route here and
used an on-stack flow.

Track which one it was, and use it to obtain src/dst addrs.
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables ethtool to set the loopback mode on a given interface.
By configuring the interface in loopback mode in conjunction with a policy
route / rule, a userland application can stress the egress / ingress path
exposing the flows of the change in progress and potentially help developer(s)
understand the impact of those changes without even sending a packet out
on the network.

Following set of commands illustrates one such example -
    a) ip -4 addr add 192.168.1.1/24 dev eth1
    b) ip -4 rule add from all iif eth1 lookup 250
    c) ip -4 route add local 0/0 dev lo proto kernel scope host table 250
    d) arp -Ds 192.168.1.100 eth1
    e) arp -Ds 192.168.1.200 eth1
    f) sysctl -w net.ipv4.ip_nonlocal_bind=1
    g) sysctl -w net.ipv4.conf.all.accept_local=1
    # Assuming that the machine has 8 cores
    h) taskset 000f netserver -L 192.168.1.200
    i) taskset 00f0 netperf -t TCP_CRR -L 192.168.1.100 -H 192.168.1.200 -l 30
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I don't know why %pI6 doesn't compress, but the format specifier is
kernel-standard, so use it.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 20G supported and advertising bit definitions.
20G will be supported with the 57840 chips.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
------
 include/linux/ethtool.h |    4 ++++
 1 files changed, 4 insertions(+), 0 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Now we can pick it out of the transport's flow key.
Signed-off-by: David S. Miller <davem@davemloft.net>

Now we can pick it out of the provided flow key.
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows us to acquire the exact route keying information from the
protocol, however that might be managed.

It handles all of the possibilities, from the simplest case of storing
the key in inet->cork.fl to the more complex setup SCTP has where
individual transports determine the flow.
Signed-off-by: David S. Miller <davem@davemloft.net>

Operation order is now transposed, we first create the child
socket then we try to hook up the route.
Signed-off-by: David S. Miller <davem@davemloft.net>

This is just like inet_csk_route_req() except that it operates after
we've created the new child socket.

In this way we can use the new socket's cork flow for proper route
key storage.

This will be used by DCCP and TCP child socket creation handling.
Signed-off-by: David S. Miller <davem@davemloft.net>

Several future simplifications are possible now because of this.

For example, the sctp_addr unions can simply refer directly to
the flowi information.
Signed-off-by: David S. Miller <davem@davemloft.net>

All invokers of ip_queue_xmit() must make certain that the
socket is locked.  All of SCTP, TCP, DCCP, and L2TP now make
sure this is the case.

Therefore we can use the cork flow during output route lookup in
ip_queue_xmit() when the socket route check fails.
Signed-off-by: David S. Miller <davem@davemloft.net>

These two functions must be invoked only when the socket is locked
(because socket identity modifications are made non-atomically).

Therefore we can use the cork flow for output route lookups.
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to make sure that an l2tp socket's inet cork flow is
fully filled in, when it's encapsulated in UDP.
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that the socket is consistently locked in these two routines,
this transformation is legal.
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp_xmit_skb() must take the socket lock.  It makes use of ip_queue_xmit()
which expects to execute in a socket atomic context.

Since we execute this function in software interrupts, we cannot use the
usual lock_sock()/release_sock() sequence, instead we have to use
bh_lock_sock() and see if a user has the socket locked, and if so drop
the packet.
Signed-off-by: David S. Miller <davem@davemloft.net>

Both l2tp_ip_connect() and l2tp_ip_sendmsg() must take the socket
lock.  They both modify socket state non-atomically, and in particular
l2tp_ip_sendmsg() increments socket private counters without using
atomic operations.
Signed-off-by: David S. Miller <davem@davemloft.net>

Since this is invoked from inet_stream_connect() the socket is locked
and therefore this usage is safe.
Signed-off-by: David S. Miller <davem@davemloft.net>