If the gpiochip supports the .get_direction() callback, then
the initial state of the descriptor flags should be set up
as output accordingly. Also put in comments explaining what is
going on.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch renames the gpio-generic.c into gpio-mmio.c.
This is because currently the file only contains code
for a memory-mapped GPIO driver. There isn't any support
for ioports or other resource type.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIO_GENERIC_PLATFORM is a tristate. If the module option is
selected the resulting gpio-generic.ko will lack most of the
module initialzation and probe code.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds gpio-signaled acpi event support. It is used for
power button on hisilicon D02 board, an arm64 platform.

The corresponding DSDT file is defined as follows:
Device(GPI0) {
	Name(_HID, "HISI0181")
	Name(_ADR, 0)
	Name(_UID, 0)

	Name (_CRS, ResourceTemplate ()  {
		Memory32Fixed (ReadWrite, 0x802e0000, 0x10000)
		Interrupt (ResourceConsumer, Level, ActiveHigh,
		Exclusive,,,)  {344}
	})

	Device(PRTa) {
		Name (_DSD, Package () {
		Package () {
			Package () {"reg",0},
			Package () {"snps,nr-gpios",32},
		}
		})
	}

	Name (_AEI, ResourceTemplate () {
		GpioInt(Edge, ActiveLow, ExclusiveAndWake,
		PullUp, , " \\_SB.GPI0") {8}
	})

	Method (_E08, 0x0, NotSerialized) {
		Notify (\_SB.PWRB, 0x80)
	}
}
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiang Qiu <qiujiang@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch converts device node to fwnode for dwapb driver, so
as to provide a unified fwnode for DT and ACPI bindings.
Tested-by: Alan Tull <delicious.quinoa@gmail.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiang Qiu <qiujiang@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch removed the name property from dwapb_port_property.
The name property is redundant, since we can get this info
from dwapb_gpio dev node.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiang Qiu <qiujiang@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The gpio-mpc8xxx driver requires IRQ domains but can be built
without them, resulting on a failure to build certain randconfigs
on ARM:

drivers/gpio/gpio-mpc8xxx.c: In function 'mpc8xxx_gpio_to_irq':
drivers/gpio/gpio-mpc8xxx.c:92:10: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration]
   return irq_create_mapping(mpc8xxx_gc->irq, offset);

This selects IRQ_DOMAIN from the driver to ensure we can build it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5df7fd46 ("gpio/qoriq: Add qoriq platforms support")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

NVIDIA's Tegra210 support the HW debounce in the GPIO controller
for all its GPIO pins.

Add support for setting debounce timing by implementing the
set_debounce callback of gpiochip.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Move the file scoped multiple global variable from Tegra GPIO
driver to the structure and make this as gpiochip data which
can be referred from GPIO chip callbacks.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The data member of the of_device_id is the constant type
and hence all static structure which is used for this
initialisation as static.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Suggested-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use of_device_get_match_data() for getting matched data
instead of implementing this locally.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Implement this callback so that the driver reports correctly
the direction setting of each line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The gpiochip calls are already checking that the GPIO line
offsets are in range.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Make the text clearer, remove reference to confusing "positive"
and "negative" and elaborate a bit.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now GPIO IRQ loss is observed on dra7-evm after suspend/resume cycle
in the following case:
  extcon_usb1(id_irq) ->  pcf8575.gpio1 -> omapgpio6.gpio11 -> gic

the extcon_usb1 is wake up source and it enables IRQ wake up for
id_irq by calling enable/disable_irq_wake() during suspend/resume
which, in turn, causes execution of omap_gpio_wake_enable(). And
omap_gpio_wake_enable() will set/clear corresponding bit in
GPIO_IRQWAKEN_x register.

omapgpio6 configuration after boot - wakeup is enabled for GPIO IRQs
by default from  omap_gpio_irq_type:
GPIO_IRQSTATUS_SET_0    | 0x00000400
GPIO_IRQSTATUS_CLR_0    | 0x00000400
GPIO_IRQWAKEN_0         | 0x00000400
GPIO_RISINGDETECT       | 0x00000000
GPIO_FALLINGDETECT      | 0x00000400

omapgpio6 configuration after after suspend/resume cycle:
GPIO_IRQSTATUS_SET_0    | 0x00000400
GPIO_IRQSTATUS_CLR_0    | 0x00000400
GPIO_IRQWAKEN_0         | 0x00000000 <---
GPIO_RISINGDETECT       | 0x00000000
GPIO_FALLINGDETECT      | 0x00000400

As result, system will start to lose interrupts from pcf8575 GPIO
expander, because when OMAP GPIO IP is in smart-idle wakeup mode, there
is no guarantee that transition(s) on input non wake up GPIO pin will
trigger asynchronous wake-up request to PRCM and then IRQ generation.
IRQ will be generated when GPIO is in active mode - for example, some
time after accessing GPIO bank registers IRQs will be generated
normally, but issue will happen again once PRCM will put GPIO in low
power smart-idle wakeup mode.

Note 1. Issue is not reproduced if debounce clk is enabled for GPIO
bank.

Note 2. Issue hardly reproducible if GPIO pins group contains both
wakeup/non-wakeup gpios - for example, it will be hard to reproduce
issue with pin2 if GPIO_IRQWAKEN_0=0x1 GPIO_IRQSTATUS_SET_0=0x3
GPIO_FALLINGDETECT = 0x3 (TRM "Power Saving by Grouping the Edge/Level
Detection").

Note 3. There nothing common bitween System wake up and OMAP GPIO bank
IP wake up logic - the last one defines how the GPIO bank ON-IDLE-ON
transition will happen inside SoC under control of PRCM.

Hence, fix the problem by removing omap_set_gpio_wakeup() function
completely and so keeping always in sync GPIO IRQ mask/unmask
(IRQSTATUS_SET) and wake up enable (GPIO_IRQWAKEN) bits; and adding
IRQCHIP_MASK_ON_SUSPEND flag in OMAP GPIO irqchip. That way non wakeup
GPIO IRQs will be properly masked/unmask by IRQ PM core during
suspend/resume cycle.

Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Bard Liao <bardliao@realtek.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Manohar Vanga <manohar.vanga@gmail.com>
Cc: devel@driverdev.osuosl.org
Acked-by: Martyn Welch <martyn@welchs.me.uk>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Michael Buesch <m@bues.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Feng Tang <feng.tang@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of indirectly selecting GPIOLIB via the
ARCH_REQUIRE_GPIOLIB symbol, just select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: linux-snps-arc@lists.infradead.org
Acked-by: Vineet Gupta <vgupt@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: sparclinux@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Replace "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB"
as this can now be selected directly.

Cc: Michael Büsch <m@bues.ch>
Cc: Mikael Starvik <starvik@axis.com>
Cc: linux-cris-kernel@axis.com
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: nios2-dev@lists.rocketboards.org
Acked-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Replace "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB"
as this can now be selected directly.

Cc: Michael Büsch <m@bues.ch>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: linux-metag@vger.kernel.org
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Replace "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB"
as this can now be selected directly.

Cc: Michael Büsch <m@bues.ch>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Acked-by: Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The GPIOLIB symbol currently require that
ARCH_WANT_OPTIONAL_GPIOLIB or ARCH_REQUIRE_GPIOLIB is selected
to be selectable.

The ARCH_REQUIRE_GPIOLIB does only one thing: select GPIOLIB.

This is just confusing: architectures that want GPIOLIB should
be able to configure it in no matter what, and those who
require it should just select GPIOLIB.

It also creates problems for drivers that need to state
"select GPIOLIB" to get dependencies: those depend on the
selected architecture to select
ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB first, and will cause
compile errors for the few archs that state neither.

These intermediary symbols need to go.

As a first step, remove the dependencies so that:

- ARCH_WANT_OPTIONAL_GPIOLIB becomes a noop (GPIOLIB will be
  available for everyone) and

- "select ARCH_REQUIRE_GPIOLIB" can be replaced by just
  "select GPIOLIB"

After this patch we can follow up with patches cleaning up the
architectures one-by one and eventually remove the
ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB symbols altogether.
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Keep the words talking about what a GPIO bank is, but remove the
binding. We have not agreed that this is something we want to have.
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This renames gpiod_set_array_value_priv() to
gpiod_set_array_value_complex() and moves it to the gpiolib.h
private header file so we can reuse it in the subsystem.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix a typo causing a build regression.

Fixes: f90c6bdb ("gpio: f7188x: use the new open drain callback")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>