This could be a bit confusing to see warning about lacking support for
5 GHz band if your device supports 2.4 GHz only.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Support for N-PHY rev 8 with 0x2057 rev 5 is almost ready, but we still
need to figure out how to handle rev 9 first.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Initialization of N-PHY radio revs 5 and 7 requires writing to 0x1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Type of radio has a major meaning for the driver. There is quite some
code that does initialization/calibration depending on the radio rev.
Knowing radio params is quite important to provide help to users, so
print it even with debugging disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

When ERTM support is disabled, then do not even send ERTM configuration
option even if the remote side supports it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When the white list is in use the code would not update the
HCI_CONNECTABLE flag if it gets changed through the ioctl code (e.g.
hciconfig hci0 pscan). Since the flag is important for properly
accepting incoming connections add code to fix it up if necessary and
emit a New Settings mgmt event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds support for looking up entries in the white list when
HCI_CONNECTABLE is not set. The logic is fairly simple: if we're
connectable check the black list, if we're not connectable check the
white list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Page scan should be enabled either if the connectable setting is set or
if there are any entries in the BR/EDR white list. This patch implements
such behavior by updating the two places that were making decisions on
whether to enable page scan or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The conditions for accepting an incoming connections are already
non-trivial and will become more so once a white list is added. This
patch breaks up the checks for when to reject the request by creating a
helper function for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Since page scan might be enabled by Add Device we should not implicitly
set connectable whenever something else than Set Connectable changes it.
This patch makes sure that we don't set HCI_CONNECTABLE for these cases
if there are any entries in the white list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When we're removing the last item in the white list or adding the first
one to it and HCI_CONNECTABLE is not set we need to update the current
page scan. This patch adds a simple helper function for the purpose and
calls it from the respective mgmt command handlers.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch extends the Add/Remove device commands by letting user space
pass BR/EDR addresses to them. The resulting entries get stored in a new
hdev->whitelist list. The idea is that we can now selectively accept
connections from devices in the list even though HCI_CONNECTABLE is not
set (the actual implementation of this is coming in a subsequent patch).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We already have several lists with struct bdaddr_list entries, and there
will be more in the future. Since the operations for adding, removing,
looking up and clearing entries in these lists are exactly the same it
doesn't make sense to define new functions for every single list. This
patch unifies the functions by passing the list_head to them instead of
a hci_dev pointer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Authenticated Payload Timeout Expired event is valid for
controllers with BR/EDR Secure Connections support, but also for
LE only controllers supporting LE Ping feature. When either of them
is available enable this event. Previous it was not enabled when
the controller was only supporting LE operation.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Add support for the QCA6174 chip.

    T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 30 Spd=12  MxCh= 0
    D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
    P:  Vendor=13d3 ProdID=3432 Rev=00.02
    C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
    I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Anantha Krishnan <ananthk@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

All LE controllers always implicitly stop advertising when establishing
connections. Therefore, be sure to clear the flag in the event handler
for new LE connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If the connectable state change doesn't require any special HCI commands
the set_connectable_update_settings() function is used instead of the
set_connectable_complete() function. We must therefore make sure to call
hci_update_background_scan() there as well. This code path is used also
when we're powered off, but that's fine since hci_update_background_scan()
has the necessary checks for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The connectable and discoverable mgmt settings are supported both for LE
and BR/EDR controllers so they do not belong behind a lmp_bredr_capable()
condition. This patch fixes the issue in get_supported_settings().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If any of the HCI commands from the hci_stop_discovery function were
successfully sent we need to set the discovery state to STOPPING. The
Stop Discovery code was already handling this, but the code in
clean_up_hci_state was not. This patch updates the hci_stop_discovery to
return a bool to indicate whether it queued any commands and the
clean_up_hci_state() function respectively to look at the return value
and call hci_discovery_set_state() if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

There are many different places that can disable LE scanning but we only
want to re-enable advertising in hci_cc_le_set_scan_enable() for a very
specific use case, which is when the active scanning part of Start
Discovery is complete. Because of this, fix the discovery state check to
test for the exact state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Many controllers allow simultaneous active scanning and advertising
(e.g. Intel and Broadcom) but some do not (e.g. CSR). It's therefore
safest to implement mutual exclusion of these states in the kernel.

This patch ensures that the two states are never entered simultaneously.
Extra precaution needs to be taken for outgoing connection attempts in
slave role (i.e. through directed advertising) in which case the
operation that came first has precedence and the one that comes after
gets a rejection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Most controllers do not support advertising while initiating an LE
connection. We also have to first disable current advertising if the
initiation is going to happen through direct advertising. Therefore,
simply stop advertising as the first thing when starting to issue
commands to establish an LE connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When deciding to call disable_advertising() we're interested in the real
state instead of the mgmt setting. Use therefore HCI_LE_ADV instead of
the HCI_ADVERTISING flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

By adding support for disabling advertising when necessary and doing the
checks for existing LE connections inside the enable_advertising
function we can simplify the calling code quite a lot.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Now that we have a flag for tracking the real advertising state we
should use that to determine whether it's safe to update the random
address or not. The couple of places that were clearing the flag due to
a pending request need to be updated too.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Since the real advertising state is now tracked with its own flag we can
simply set/unset the HCI_ADVERTISING flag in the
set_advertising_complete function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Having a single HCI_ADVERTISING flag is problematic since it tries to
track both the real advertising state and the corresponding mgmt
setting. To make the logic simpler and more reliable add a new flag that
only tracks the actual advertising state that has been written to the
controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

New Broadcom PCIe devices (802.11ac ones?) use Gen2 and have to be
initialized differently.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This changes
b43-phy0: Found Radio: Manuf 0x17F, Version 0x7769, Revision 4
to the
b43-phy0: Found Radio: Manuf 0x17F, Version 0x2069, Revision 4
which matches what closed source driver reports:
$ wl revinfo
radiorev 0x42069000
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This allows adding more revisions support, spotting lacking tables and
unifies naming schema.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Function rt2800usb_autorun_detect() passes the address of a variable
allocated onto the stack to be used for DMA by the USB layer. This has
been caught by my debugging-enabled kernel.

This patch change things in order to allocate that variable via
kmalloc, and it adjusts things to handle the kmalloc failure case,
propagating the error.

[ 7363.238852] ------------[ cut here ]------------
[ 7363.243529] WARNING: CPU: 1 PID: 5235 at lib/dma-debug.c:1153 check_for_stack+0xa4/0xf0()
[ 7363.251759] ehci-pci 0000:00:04.1: DMA-API: device driver maps memory fromstack [addr=ffff88006b81bad4]
[ 7363.261210] Modules linked in: rt2800usb(O+) rt2800lib(O) rt2x00usb(O) rt2x00lib(O) rtl818x_pci(O) rtl8187 led_class eeprom_93cx6 mac80211 cfg80211 [last unloaded: rt2x00lib]
[ 7363.277143] CPU: 1 PID: 5235 Comm: systemd-udevd Tainted: G           O  3.16.0-rc3-wl+ #31
[ 7363.285546] Hardware name: System manufacturer System Product Name/M3N78 PRO, BIOS ASUS M3N78 PRO ACPI BIOS Revision 1402 12/04/2009
[ 7363.297511]  0000000000000009 ffff88006b81b710 ffffffff8175dcad ffff88006b81b758
[ 7363.305062]  ffff88006b81b748 ffffffff8106d372 ffff88006cf10098 ffff88006cead6a0
[ 7363.312622]  ffff88006b81bad4 ffffffff81c1e7c0 ffff88006cf10098 ffff88006b81b7a8
[ 7363.320161] Call Trace:
[ 7363.322661]  [<ffffffff8175dcad>] dump_stack+0x4d/0x6f
[ 7363.327847]  [<ffffffff8106d372>] warn_slowpath_common+0x82/0xb0
[ 7363.333893]  [<ffffffff8106d3e7>] warn_slowpath_fmt+0x47/0x50
[ 7363.339686]  [<ffffffff813a93b4>] check_for_stack+0xa4/0xf0
[ 7363.345298]  [<ffffffff813a995c>] debug_dma_map_page+0x10c/0x150
[ 7363.351367]  [<ffffffff81521bd9>] usb_hcd_map_urb_for_dma+0x229/0x720
[ 7363.357890]  [<ffffffff8152256d>] usb_hcd_submit_urb+0x2fd/0x930
[ 7363.363929]  [<ffffffff810eac31>] ? irq_work_queue+0x71/0xd0
[ 7363.369617]  [<ffffffff810ab5a7>] ? wake_up_klogd+0x37/0x50
[ 7363.375219]  [<ffffffff810ab7a5>] ? console_unlock+0x1e5/0x420
[ 7363.381081]  [<ffffffff810abc25>] ? vprintk_emit+0x245/0x530
[ 7363.386773]  [<ffffffff81523d3c>] usb_submit_urb+0x30c/0x580
[ 7363.392462]  [<ffffffff81524295>] usb_start_wait_urb+0x65/0xf0
[ 7363.398325]  [<ffffffff815243ed>] usb_control_msg+0xcd/0x110
[ 7363.404014]  [<ffffffffa005514d>] rt2x00usb_vendor_request+0xbd/0x170 [rt2x00usb]
[ 7363.411544]  [<ffffffffa0074292>] rt2800usb_autorun_detect+0x32/0x50 [rt2800usb]
[ 7363.418986]  [<ffffffffa0074aa1>] rt2800usb_read_eeprom+0x11/0x70 [rt2800usb]
[ 7363.426168]  [<ffffffffa0063ffd>] rt2800_probe_hw+0x11d/0xf90 [rt2800lib]
[ 7363.432989]  [<ffffffffa0074b7d>] rt2800usb_probe_hw+0xd/0x50 [rt2800usb]
[ 7363.439808]  [<ffffffffa00453d8>] rt2x00lib_probe_dev+0x238/0x7c0 [rt2x00lib]
[ 7363.446992]  [<ffffffffa00bfa48>] ? ieee80211_led_names+0xb8/0x100 [mac80211]
[ 7363.454156]  [<ffffffffa0056116>] rt2x00usb_probe+0x156/0x1f0 [rt2x00usb]
[ 7363.460971]  [<ffffffffa0074250>] rt2800usb_probe+0x10/0x20 [rt2800usb]
[ 7363.467616]  [<ffffffff8152799e>] usb_probe_interface+0xce/0x1c0
[ 7363.473651]  [<ffffffff81480c20>] really_probe+0x70/0x240
[ 7363.479079]  [<ffffffff81480f01>] __driver_attach+0xa1/0xb0
[ 7363.484682]  [<ffffffff81480e60>] ? __device_attach+0x70/0x70
[ 7363.490461]  [<ffffffff8147eef3>] bus_for_each_dev+0x63/0xa0
[ 7363.496146]  [<ffffffff814807c9>] driver_attach+0x19/0x20
[ 7363.501570]  [<ffffffff81480468>] bus_add_driver+0x178/0x220
[ 7363.507270]  [<ffffffff8148151b>] driver_register+0x5b/0xe0
[ 7363.512874]  [<ffffffff815271b0>] usb_register_driver+0xa0/0x170
[ 7363.518905]  [<ffffffffa007a000>] ? 0xffffffffa0079fff
[ 7363.524074]  [<ffffffffa007a01e>] rt2800usb_driver_init+0x1e/0x20 [rt2800usb]
[ 7363.531247]  [<ffffffff810002d4>] do_one_initcall+0x84/0x1b0
[ 7363.536932]  [<ffffffff8113aa60>] ? kfree+0xd0/0x110
[ 7363.541931]  [<ffffffff8112730a>] ? __vunmap+0xaa/0xf0
[ 7363.547538]  [<ffffffff810ca07e>] load_module+0x1aee/0x2040
[ 7363.553141]  [<ffffffff810c6f10>] ? store_uevent+0x50/0x50
[ 7363.558676]  [<ffffffff810ca66e>] SyS_init_module+0x9e/0xc0
[ 7363.564285]  [<ffffffff81764012>] system_call_fastpath+0x16/0x1b
[ 7363.570338] ---[ end trace 01ef5f822bea9882 ]---
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>