The recent ACPICA patch
(ACPICA: FADT: Favor 32-bit register addresses for compatibility)
makes machine to use the right FADT HW addresses
and C-states now work fine.

http://bugzilla.kernel.org/show_bug.cgi?id=8246Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: Mark Doughty <me@markdoughty.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>

ACPI has smart batteries, which work in units of energy and measure
rate of (dis)charge as power, thus it is not appropriate to export it
as a current_now. Current_now will still be exported to allow
for userland applications to match.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>

When cpufreq driver call acpi_processor_preregister_performance() , function
will clean up pr->performance even if there is possibly already registered
other cpufreq driver. The patch fix this potential problem. It also remove
double checks in P domain basic validity code and move these checks to function
where _PSD data is captured.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>

In acpi_bus_ops, only the acpi_op_add and acpi_op_start flags are used,
so remove all the rest.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

No drivers use the .shutdown method, so remove it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

No drivers use the .lock and .scan methods, and the Linux/ACPI
code doesn't even provide a way to invoke them, so remove them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Due to poor thermal design or Linux driving hardware outside its thermal
envelope, some systems will reach critical temperature and shut down
under high load. This patch adds support for forcing a polling-based
passive trip point if the firmware doesn't provide one. The assumption
is made that the processor is the most practical means to reduce the
dynamic heat generation, so hitting the passive thermal limit will cause
the CPU to be throttled until the temperature stabalises around the
defined value.

UI is provided via a "passive" sysfs entry in the thermal zone
directory. It accepts a decimal value in millidegrees celsius, or "0" to
disable the functionality. Default behaviour is for this functionality
to be disabled.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>

> drivers/acpi/thermal.c: In function 'thermal_notify':
> drivers/acpi/thermal.c:768: error: 'struct device' has no member named 'bus_id'
>
> Caused by commit b1569e99 ("ACPI: move
> thermal trip handling to generic thermal layer") interacting with commit
> d4a078fca590911cdf87a8eaffee1b6e643c2558 ("driver core: get rid of struct
> device's bus_id string array").
>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Len Brown <len.brown@intel.com>

> arch/x86/kernel/cpu/cpufreq/longhaul.c: In function 'longhaul_setstate':
> arch/x86/kernel/cpu/cpufreq/longhaul.c:308: error: implicit declaration of function 'acpi_set_register'
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Compile-tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Len Brown <len.brown@intel.com>

This patch removes the suggestion that ec.o link order is important,
because it doesn't matter since acpi_ec_init() is no longer an initcall.
And it puts together most of the core modules that are not configurable.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

This patch makes acpi_init() call acpi_wakeup_device_init() directly.
Previously, acpi_wakeup_device_init() was a late_initcall (sequence 7).

acpi_wakeup_device_init() depends on acpi_wakeup_device_list, which
is populated when ACPI devices are enumerated by acpi_init() ->
acpi_scan_init().  Using late_initcall is certainly enough to make
sure acpi_wakeup_device_list is populated, but it is more than
necessary.  We can just as easily call acpi_wakeup_device_init()
directly from acpi_init(), which avoids the initcall magic.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

This patch makes acpi_init() call acpi_sleep_proc_init() directly.
Previously, acpi_sleep_proc_init() was a late_initcall (sequence 7),
apparently to make sure that the /proc hierarchy already exists:

    2003/02/13 12:38:03-06:00 mochel
    acpi sleep: demote sleep proc file creation.

    - Make acpi_sleep_proc_init() a late_initcall(), and not called from
      acpi_sleep_init(). This guarantees that the acpi proc hierarchy is at
      least there when we create the dang file.

This should no longer be an issue because acpi_bus_init() (called early
in acpi_init()) creates acpi_root_dir (/proc/acpi).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

This patch makes acpi_init() call init_acpi_device_notify() directly.
Previously, init_acpi_device_notify() was an arch_initcall (sequence 3),
so it was called before acpi_init() (a subsys_initcall at sequence 4).

init_acpi_device_notify() sets the platform_notify and
platform_notify_remove function pointers.  These pointers
are not used until acpi_init() enumerates ACPI devices in
this path:

    acpi_init()
	    acpi_scan_init()
		acpi_bus_scan()
		    acpi_add_single_object()
			acpi_device_register()
			    device_add()
				<use platform_notify>

So it is sufficient to have acpi_init() call init_acpi_device_notify()
directly before it enumerates devices.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

This patch makes acpi_init() call acpi_debug_init() directly.
Previously, both were subsys_initcalls.  acpi_debug_init()
must happen after acpi_init(), and it's better to call it
explicitly rather than rely on link ordering.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

This patch makes acpi_init() call acpi_system_init() directly.
Previously, both were subsys_initcalls.  acpi_system_init()
must happen after acpi_init(), and it's better to call it
explicitly rather than rely on link ordering.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

This patch makes acpi_init() call acpi_power_init() directly.
Previously, both were subsys_initcalls.  acpi_power_init()
must happen after acpi_init(), and it's better to call it
explicitly rather than rely on link ordering.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

This patch makes acpi_init() call acpi_ec_init() directly.
Previously, both were subsys_initcalls.  acpi_ec_init()
must happen after acpi_init(), and it's better to call it
explicitly rather than rely on link ordering.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>

This patch makes acpi_init() call acpi_scan_init() directly.

Previously, both acpi_init() and acpi_scan_init() were subsys_initcalls,
and acpi_init() was called first based on the link order from the
makefile (bus.o before scan.o).

acpi_scan_init() registers the ACPI bus type, creates the root device,
and enumerates fixed-feature and namespace devices.  All of this must
be done after acpi_init(), and it's better to call acpi_scan_init()
explicitly rather than rely on the link ordering.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

This patch makes acpi_init() exit early when ACPI is disabled.
This skips a DMI check that affects ACPI power management.   The
DMI check prints a notice that is misleading when ACPI is disabled.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Version 20090320.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

For predefined method validation. Index value in warning message
could be off by one.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

If both the 32-bit and 64-bit addresses are non-null, use the
32-bit address. Provides Windows compatibility.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Use the 32-bit register addresses whenever they are non-zero. This
means that the 32-bit addresses are favored over the 64-bit
(GAS) addresses. The 64-bit addresses are only used if the 32-bit
addresses are zero. This change provides compatibility with all
versions of Windows. The worst case that this solves is when both
the 32-bit and 64-bit addresses are non-zero, but only the 32-bit
addresses are actually valid. This appears to happen in some
BIOSes because in this case, Windows uses the 32-bit addresses.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Microsoft website uses 0xCF8-0xD00. Should be 0xCF8-0xCFF (Two
32-bit registers.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

One entry in the protected port table eliminated. Added extra
comments to describe each table entry.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Removed unused code for dump of args and locals. General cleanup
and splitting of long lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Affects PM1 Control register only. When reading the register, zero
the write-only bits as per the ACPI spec.  ACPICA BZ 443. Lin Ming.

http://www.acpica.org/bugzilla/show_bug.cgi?id=443Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

This interface is no longer necessary. Requests should be validated
on a per-field basis, not on the entire operation region.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Protect certain I/O ports from reads/writes. Provides MS
compatibility. New module, hwvalid.c
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

As per the ACPI specification, preserve (read/modify/write) all
bits that are defined as either reserved or ignored (PM control
control registers only.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Ignored bits must be preserved according to the ACPI spec.
Usually this means a read/modify/write when writing to the
register.  However, for status registers, writing a one means
clear the event.  Writing a zero means preserve the event (do not
clear.) This behavior is clarified in the ACPI 4.0 spec, and the
ACPICA code now simply always writes a zero to the ignored bit.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>