Having this hidden config below the COMMON_CLK_QCOM config causes
menuconfig to stop indenting config items after it.

        <*> Support for Qualcomm's clock controllers
        {M}   APQ8084 Global Clock Controller
        <M>   APQ8084 Multimedia Clock Controller
        {M}   IPQ806x Global Clock Controller
        <M>   IPQ806x LPASS Clock Controller
        <M> MSM8660 Global Clock Controller
        <M> MSM8916 Global Clock Controller
        {M} APQ8064/MSM8960 Global Clock Controller
        <M> APQ8064/MSM8960 LPASS Clock Controller
        <M> MSM8960 Multimedia Clock Controller
        {M} MSM8974 Global Clock Controller
        <M> MSM8974 Multimedia Clock Controller

Move it up above anything else so that we don't get odd
indenting.

Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Now that qcom_cc_remove() is a nop, drop calls to
qcom_cc_remove() and any empty driver remove functions.

Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Some APIs in qcom_cc_probe() don't have a devm counterpart, so we
have to use the calling device's platform data to pass pointers
to the remove path. Let's use devm_add_action() instead, so that
the remove path doesn't need to do anything, allowing us to
remove qcom_cc_remove() entirely.

Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Add support for new PLL-type for stih418 A9-PLL.
Currently the 407_A9_PLL type being used, it is corrected with this patch
4600c28 PLL allows to reach higher frequencies
so its programming algorithm is extended.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Change A9 PLL rate, as per requirement from the cpufreq framework,
for DVFS. For rate change, the A9 clock needs to be temporarily sourced
from PLL external to A9 and then sourced back to A9-PLL
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The patch adds support for enable/disable of the Clockgen PLLs.
clkgen_pll_enable/clkgen_pll_disable added as generic function for all PLLs.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The oxili_cx GDSC is inside the power domain of the oxili GDSC.
Add the dependency so that the CX domain can properly power up.
Reported-by: Rob Clark <robdclark@gmail.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Export these symbols so they can be used in loadable kernel
modules.

Cc: Rob Clark <robdclark@gmail.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

This patch adds the driver and devicetree documentation for the
Silicon Labs SI514 clock generator chip. This is an I2C controlled
oscillator capable of generating clock signals ranging from 100kHz
to 250MHz.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd@codeaurora.org: Drop clk.h include, remove some casts]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Pull mediatek clock support and fixes from James Liao:

"This is a collection of new Mediatek clocks support and fixes.
These patches come from Joe and me, including clock support for
subsystems, GPT and some minor fixes."

* 'v4.3-rc3-clk' of https://github.com/jamesjjliao/linux:
  clk: mediatek: Add USB clock support in MT8173 APMIXEDSYS
  clk: mediatek: Add subsystem clocks of MT8173
  dt-bindings: ARM: Mediatek: Document devicetree bindings for clock controllers
  clk: mediatek: Fix rate and dependency of MT8173 clocks
  clk: mediatek: Add fixed clocks support for Mediatek SoC.
  clk: mediatek: Add __initdata and __init for data and functions
  clk: mediatek: Remove unused code from MT8173.
  clk: mediatek: Removed unused dpi_ck clock from MT8173
  clk: mediatek: add 13mhz clock for MT8173

drivers/clk/samsung/clk-exynos7.c:896:33:
warning: symbol 'fixed_rate_clks_fsys0' was not declared. Should
it be static?
drivers/clk/samsung/clk-exynos7.c:1010:33:
warning: symbol 'fixed_rate_clks_fsys1' was not declared. Should
it be static?

Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Pull updates from Sylwester Nawrocki:

"Fixes, improvements and addition of some missing features
of the exynos7 clock controller driver."

* tag 'clk-samsung-4.4' of git://linuxtv.org/snawrocki/samsung:
  clk: samsung: exynos7: Add required clock tree for UFS
  clk: samsung: exynos7: Add missing fixed_clks to cmu_info
  clk: samsung: exynos7: Correct CMU_FSYS1 clocks names
  clk: samsung: exynos7: Correct CMU_FSYS0 clocks names
  clk: samsung: exynos7: Correct CMU_PERIS clocks names
  clk: samsung: exynos7: Correct CMU_PERIC1 clocks names
  clk: samsung: exynos7: Correct CMU_PERIC0 clocks names
  clk: samsung: exynos7: Correct CMU_CCORE clocks names
  clk: samsung: exynos7: Correct CMU_TOP1 clocks names
  clk: samsung: exynos7: Correct CMU_TOP0 clocks names
  clk: samsung: exynos7: Adds missing clocks gates of CMU_TOPC
  clk: samsung: exynos7: Change the CMU_TOPC block clock names
  clk: samsung: exynos7: Correct nr_clk_ids for fsys1
  clk: samsung: exynos7: Correct nr_clk_ids for fsys0
  clk: samsung: exynos7: Fix CMU TOP1 block
  clk: samsung: exynos7: Fix CMU TOPC block clock

* clk-fixes: (3 commits)
  clk: ti: dflt: fix enable_reg validity check
  clk: ti: fix dual-registration of uart4_ick
  clk: ti: clk-7xx: Remove hardwired ABE clock configuration

We have couple of standard but rare used baudrates which are not supported by
1,8432MHz reference frequency. Besides that user can potentially ask for any
baudrate (via BOTHER flag) and we currently don't fully support that. Since
clk-fractional-divider is moved to use rational best approximation for
reference frequency we may amend the driver to support whatever user wants.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

This patch converts the code to use rational best approximation algorithm which
is much more precise.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The ->mwidth and ->nwidth fields will be used by clk-fractional-divider when it
will be switched to rational base approximation algorithm.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The patch adds mwidth and nwidth fields to the struct clk_fractional_divider
for further usage. While here, use GENMASK() instead of open coding this
functionality.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Rename function parameter to be more explicit what it is for. This also makes
it in align with struct clk_ops.

There is no functional change.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Pull fixes from Tero Kristo:

"A few TI clock driver fixes to pull against 4.3-rc"

* 'for-4.3-rc/ti-clk-fixes' of https://github.com/t-kristo/linux-pm: (3 commits)
  clk: ti: dflt: fix enable_reg validity check
  clk: ti: fix dual-registration of uart4_ick
  clk: ti: clk-7xx: Remove hardwired ABE clock configuration

The default clock enabling functions for TI clocks -
omap2_dflt_clk_enable() and omap2_dflt_clk_disable() perform a
NULL check for the enable_reg field of the clk_hw_omap structure.
This enable_reg field however is merely a combination of the index
of the master IP module, and the offset from the master IP module's
base address. A value of 0 is perfectly valid, and the current error
checking will fail in these cases. The issue was found when trying
to enable the iva2_ck clock on OMAP3 platforms.

So, switch the check to use IS_ERR. This correction is similar to the
logic used in commit c807dbed ("clk: ti: fix ti_clk_get_reg_addr
error handling").

Fixes: 9f37e90e ("clk: ti: dflt: move support for default gate clock..")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

On the OMAP AM3517 platform the uart4_ick gets registered
twice, causing any power management to /dev/ttyO3 to fail
when trying to wake the device up.

This solves the following oops:

[] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa09e008
[] PC is at serial_omap_pm+0x48/0x15c
[] LR is at _raw_spin_unlock_irqrestore+0x30/0x5c

Fixes: aafd900c ("CLK: TI: add omap3 clock init file")
Cc: stable@vger.kernel.org
Cc: mturquette@baylibre.com
Cc: sboyd@codeaurora.org
Cc: linux-clk@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@lists.codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

The ABE related clocks should be configured via DT and not have it wired
inside of the kernel.

Fixes: a74c52de ("clk: ti: clk-7xx: Correct ABE DPLL configuration")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

This simplifies the given function by getting rid of the manual
sign extension as well as saving an absolute value in an extra
variable.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

mmc host controller's IO input/output timing is unpredictable if
bootloader execute tuning for HS200 mode. It might make kernel failed
to initialize mmc card in identification mode. The root cause is
tuning phase and degree setting for HS200 mode in bootloader aren't
applicable to that of identification mode in kernel stage. Anyway, we
can't force all bootloaders to reset tuning phase and degree setting
before into kernel. Simply reset it in rockchip_clk_register_mmc.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

On drivers/clk/mxs/clk-frac.c, the function clk_frac_round_rate returned a bad
result. The division before multiplication computes a wrong value ; the
calculation is inverted to fix the problem. The second issue is that the exact
rate have decimals and they are truncate. The consequence is that the function
clk_frac_set_rate (which use the result of clk_frac_round_rate) computes a
wrong value for the register (the rate generated can be closer to the desired
rate). The correction is : if there is decimal to the result, it is rounded to
the next larger integer.
On drivers/clk/mxs/clk-frac.c, the function clk_frac_recalc_rate returned
a bad result. The multiplication is made before the division to compute a
correct value.
Signed-off-by: Victorien Vedrine <victorien.vedrine@ophrys.net>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The function can return negative value.

The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Separate the update of pll registers from the actual set_rate function
so that the init callback does not need to access clk-API functions.

As we now have separated the getting and setting of the pll parameters
we can also directly use these new functions in other places too.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Add a new type of clocks that can be provided to a peripheral.
In addition to the peripheral clock, this new clock that can use several
input clocks as parents can generate divided rates.
This would allow a peripheral to have finer grained clocks for generating
a baud rate, clocking an asynchronous part or having more
options in frequency.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[sboyd@codeaurora.org: Transition to new clk_hw provider APIs]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Add support for the new sama5d2 SoC and adapt capabilities.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

As some more information is added to the PCR register, we'd better use
a copy of its content and modify just the peripheral-related bits.
Implement a read-modify-write for the enable() and disable() callbacks.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Add _MASK and _OFFSET values and cleanup register fields layout.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Add REF2USB_TX clock support into MT8173 APMIXEDSYS. This clock
is needed by USB 3.0.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>

Most multimedia subsystem clocks will be accessed by multiple
drivers, so it's a better way to manage these clocks in CCF.
This patch adds clock support for MM, IMG, VDEC, VENC and VENC_LT
subsystems.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>

This adds the binding documentation for the mmsys, imgsys, vdecsys,
vencsys and vencltsys controllers found on Mediatek SoCs.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>

Remove the dependency from clk_null, and give all root clocks a
typical rate, include clkph_mck_o, usb_syspll_125m and hdmitx_dig_cts.

dpi_ck was removed due to no clock reference to it.

Replace parent clock of infra_cpum with cpum_ck, which is an external
clock and can be defined in the device tree.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>

This patch adds fixed clocks support by using CCF fixed-rate
clock implementation.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>

Add __init for clock registration functions, and add __initdata for
mtk_gate_regs initial structures.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>

Remove unused header files from MT8173, and remove unused
keywords from function declaration.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>

The dpi_ck clock can be removed because it not actually used
in topckgen and subsystems.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>