Dropping a matching #ifdef check along with dropping of_match_ptr()
is just a cleanup, while dropping of_match_ptr() that has no
corresponding #ifdef fixes an actual warning.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The I2C Master Hub is a stripped down version of the GENI Serial Engine
QUP Wrapper Controller but only supporting I2C serial engines without
DMA support.

Add the I2C Master Hub serial engine compatible along the specific
requirements in a new desc struct passed through the device match data.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The I2C Master Hub is a stripped down version of the GENI Serial Engine
QUP Wrapper Controller but only supporting I2C serial engines without
DMA support.

Those I2C serial engines variants have some requirements:
- a separate "core" clock
- doesn't support DMA, thus no memory interconnect path
- fixed FIFO size not discoverable in the HW_PARAM_0 register

Add a desc struct specifying all those requirements which will be used in
a next change when adding the I2C Master Hub serial engine compatible.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The I2C Master Hub is a stripped down version of the GENI Serial Engine
QUP Wrapper Controller but only supporting I2C serial engines without
DMA support.

Add the clock list for the I2C Master Hub variant to a new desc struct
then pass it through the I2C Master Hub compatible match data.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The I2C Master Hub is a stripped down version of the GENI Serial Engine
QUP Wrapper Controller but only supporting I2C serial engines without
DMA support.

Prepare support for the I2C Master Hub variant by moving the required
clocks list to a new desc struct then passing it through the compatible
match data.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The I2C Master Hub is a stripped down version of the GENI Serial Engine
QUP Wrapper Controller but only supporting I2C serial engines without
DMA support.

Document the I2C Serial Engine variant used within the I2C Master
Hub Wrapper.

This serial engine variant lacks DMA support, requires a core clock,
and since DMA support is lacking the memory interconnect path isn't
needed.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The I2C Master Hub is a stripped down version of the GENI Serial Engine
QUP Wrapper Controller but only supporting I2C serial engines without
DMA support.

Document the variant compatible, forbid UART and SPI sub-nodes,
and remove requirement for the Master AHB clock and iommu property.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The RIIC block on the RZ/Five SoC is identical to one found on the RZ/G2UL
SoC. "renesas,riic-r9a07g043" compatible string will be used on the
RZ/Five SoC so to make this clear, update the comment to include RZ/Five
SoC.

No driver changes are required as generic compatible string
"renesas,riic-rz" will be used as a fallback on RZ/Five SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Set ACPI node as the primary fwnode of I2C adapter to allow
enumeration of child devices from the ACPI table
Signed-off-by: Zubair Waheed <zwaheed@nvidia.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

On my x05 laptop I got:
Memory type 0x12 not supported yet, not instantiating SPD

Adding the 0x12 case lead to a successful instantiated SPD AT24 EEPROM.
i801_smbus 0000:00:1f.3: SMBus using polling
i2c i2c-6: 2/2 memory slots populated (from DMI)
at24 6-0050: 256 byte spd EEPROM, read-only
i2c i2c-6: Successfully instantiated SPD at 0x50
at24 6-0051: 256 byte spd EEPROM, read-only

And then, I decoded it successfully via decode-dimms.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Introduces new helper function to aid in .probe_new() refactors. In order
to use existing i2c_get_device_id() on the probe callback, the device
match table needs to be accessible in that function, which would require
bigger refactors in some drivers using the deprecated .probe callback.

This issue was discussed in more detail in the IIO mailing list.

Link: https://lore.kernel.org/all/20221023132302.911644-11-u.kleine-koenig@pengutronix.de/Suggested-by: Nuno Sá <noname.nuno@gmail.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Angel Iglesias <ang.iglesiasg@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

This patch adds IRQ support to the PASemi I2C controller driver to
increase the performace of I2C transactions on platforms with PASemi I2C
controllers. While primarily intended for Apple silicon platforms, this
patch should also help in enabling IRQ support for older PASemi hardware
as well should the need arise.

This version of the patch has been tested on an M1 Ultra Mac Studio,
as well as an M1 MacBook Pro, and userspace launches successfully
while using the IRQ path for I2C transactions.
Signed-off-by: Arminder Singh <arminders208@outlook.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

DW_IC_COMP_VERSION register contains the ASCII representation of the
Synopsys component version. Here 0x3131312A == "111*" means version
1.11* required for DW_IC_SDA_HOLD register availability where '*' means
any letter starting from 'a'.

DW_IC_COMP_TYPE is constant and is derived from two ASCII letters "DW"
followed by a 16-bit unsigned number.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Align all defines to the same column.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Commit 90312351 ("i2c: designware: MASTER mode as separated driver")
introduced disable_int pointer but there is no real use for it. Both
i2c-designware-master.c and i2c-designware-slave.c set it to the same
i2c_dw_disable_int() and scope is inside the same kernel module.

Since i2c_dw_disable_int() is just masking interrupts and the direct
DW_IC_INTR_MASK register write looks more clear in the code use that and
remove it from common code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

In my opinion a few lines of spurious interrupt detection code can be
moved to the actual master interrupt handling function i2c_dw_isr()
without hurting readability.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

It is kind of needless to print interrupt status when code immediately
after that finds interrupt was not originating from this device.
Therefore move it after spurious interrupt detection.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Do not return with interrupt handled if host controller is off and thus
interrupt is originating from other device or is spurious.

Add a check to detect when controller is runtime suspended or
transitioning/reset. In latter case all raw interrupt status register
bits may read one. In both cases return IRQ_NONE to indicate interrupt
was not from this device.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Interrupt processing code in i2c-designware-slave.c is bit more readable
if not divided into another subroutine. Also explicit IRQ_NONE and
IRQ_HANDLED return values are more obvious.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Remove unused completion code from i2c-designware-slave.c. Used only in
i2c-designware-master.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

These struct dw_i2c_dev members are not used in i2c-designware-slave.c
so remove re-initialization of them from i2c_dw_reg_slave().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Define software status flags with a BIT() macro. While at it remove
STATUS_IDLE and replace its use with zero initialization and status
flags clearing with a mask.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Writes from I2C bus often fail when testing the i2c-designware-slave.c
with the slave-eeprom backend. The same writes work correctly when
testing with a real 24c02 EEPROM chip.

In the tests below an i2c-designware-slave.c instance with the
slave-eeprom backend is configured to act as a simulated 24c02 at
address 0x65 on an I2C host bus 6.

1. i2cset -y 6 0x65 0x00 0x55

Single byte 0x55 write into address 0x00. No data goes into simulated
EEPROM. Debug prints from the i2c_dw_irq_handler_slave():

0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4

2. i2ctransfer -y 6 w9@0x65 0x00 0xff-

Write 8 bytes with decrementing value starting from 0xff at address 0x00
and forward. Only some of the data goes into arbitrary addresses.
Content is something like below but varies:

00000000  f9 f8 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
00000050  00 00 00 00 00 00 ff fe  00 00 00 00 00 00 00 00  |................|
000000f0  00 00 00 00 00 00 00 00  00 00 00 00 00 fc fb fa  |................|

In this case debug prints were:

0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x510 : INTR_STAT=0x0

Both cases show there is more data coming from the receive FIFO still
after detecting the STOP condition. This can be seen from interrupt
status bits DW_IC_INTR_STOP_DET (0x200) and DW_IC_INTR_RX_FULL (0x4).

Perhaps due interrupt latencies the receive FIFO is not read fast
enough, STOP detection happens synchronously when it occurs on the I2C
bus and the DW_IC_INTR_RX_FULL keeps coming as long as there are more
bytes in the receive FIFO.

Fix this by reading the receive FIFO completely empty whenever
DW_IC_INTR_RX_FULL occurs. Use RFNE, Receive FIFO Not Empty bit in the
DW_IC_STATUS register to loop through bytes in the FIFO.

While at it do not test the return code from i2c_slave_event() for the
I2C_SLAVE_WRITE_RECEIVED since to my understanding this hardware cannot
generate NACK to incoming bytes and debug print itself does not have
much value.
Reported-by: Tian Ye <tianye@sugon.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Some read types from I2C bus don't work correctly when testing the
i2c-designware-slave.c with the slave-eeprom backend. The same reads
work correctly when testing with a real 24c02 EEPROM chip.

In the following tests an i2c-designware-slave.c instance with the
slave-eeprom backend is configured to act as a simulated 24c02 at
address 0x65 on an I2C host bus 6:

1. i2cdump -y 6 0x65 b (OK)
   Random read. Each byte are read using a byte address write with a
   current address read in a same message.
2. i2cdump -y 6 0x65 c (OK, was NOK before commit 3b5f7f10 when it
                        was repeating the 1st byte)
   Repeated current address read. One byte address write message
   followed by repeated current address read messages.
3. i2cdump -y 6 0x65 i (NOK, each 32 byte block repeats the 1st byte of
                        block)
   Sequential read using SMBus Block Read. For each 32 byte block a byte
   address write followed by 32 sequental reads in a same message.

These findings are explained because the implementation has had a
mismatch between hardware interrupts and what I2C slave events should be
sent after those interrupts. Despite that the case 1 happened to have
always the I2C slave events sent to a right order with a right data
between backend and the I2C bus.

Hardware generates the DW_IC_INTR_RD_REQ interrupt when another host is
attempting to read and for sequential reads after. DW_IC_INTR_RX_DONE
occurs when host does not acknowledge a transmitted byte which is an
indication the end of transmission.

Those interrupts do not match directly with I2C_SLAVE_READ_REQUESTED and
I2C_SLAVE_READ_PROCESSED events which is how the code was and is
practically using them. The slave-eeprom backend increases the buffer
index with the I2C_SLAVE_READ_PROCESSED event and returns the data from
current index when receiving only the I2C_SLAVE_READ_REQUESTED event.

That explains the repeated bytes in case 3 and also case 2 before
commit 3b5f7f10 ("i2c: designware: slave should do WRITE_REQUESTED
before WRITE_RECEIVED").

Patch fixes the case 3 while keep cases 1 and 2 working with following
changes:

- First DW_IC_INTR_RD_REQ interrupt will change the state machine to
  read in progress state, send I2C_SLAVE_READ_REQUESTED event and
  transmit the first byte from backend
- Subsequent DW_IC_INTR_RD_REQ interrupts will send
  I2C_SLAVE_READ_PROCESSED events and transmit next bytes from backend
- STOP won't change the state machine. Otherwise case 2 won't work since
  we cannot distinguish current address read from sequentiel read
- DW_IC_INTR_RX_DONE interrupt is needless since there is no mechanism
  to inform it to a backend. It cannot be used to change state machine
  at the end of read either due the same reason than above
- Next host write to us will change the state machine from read to write
  in progress state
- STATUS_WRITE_IN_PROGRESS and STATUS_READ_IN_PROGRESS are considered
  now to be status flags not the state of the driver. This is how we
  treat them in i2c-designware-master.c

While at it do not test the return code from i2c_slave_event() for
I2C_SLAVE_READ_REQUESTED and I2C_SLAVE_READ_PROCESSED since it returns
always 0.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add the new compatible for HiSilicon i2c.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The HiSilicon I2C controller can be used on embedded platform, which
boot from devicetree.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Acked-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The I2C controller IP used in the Allwinner F1C100s series of SoCs is
compatible with the ones used in the other Allwinner SoCs.

Add an F1C100s specific compatible string to the list of existing names.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

To make the code easier to understand, add longer names to the
definitions of register fields. These longer names are based on source
code published by DELL/AESS for WPCM450, but should apply just as well
to NPCM7xx and NPCM8xx.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The unlabelled registers NPCM_I2CCTL4 to NPCM_I2CSCLHT overlap with the
bank 1 registers below, and they are accessed after selecting bank 0, so
they clearly belong to bank 0.

Move them together with the other bank 0 registers, and move the
unrelated definition of npcm_i2caddr down to keep the banked registers
in one piece.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add i2c support for MT7986 SoC.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add i2c compatible for MT7986 SOC.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Use msix or msi interrupts if the hardware supports it. Else, fallback to
legacy interrupts.
Co-developed-by: Basavaraj Natikar <basavaraj.natikar@amd.com>
Signed-off-by: Basavaraj Natikar <basavaraj.natikar@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Pull fbdev fixes from Helge Deller:
 "A use-after-free bugfix in the smscufx driver and various minor error
  path fixes, smaller build fixes, sysfs fixes and typos in comments in
  the stifb, sisfb, da8xxfb, xilinxfb, sm501fb, gbefb and cyber2000fb
  drivers"

* tag 'fbdev-for-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
  fbdev: cyber2000fb: fix missing pci_disable_device()
  fbdev: sisfb: use explicitly signed char
  fbdev: smscufx: Fix several use-after-free bugs
  fbdev: xilinxfb: Make xilinxfb_release() return void
  fbdev: sisfb: fix repeated word in comment
  fbdev: gbefb: Convert sysfs snprintf to sysfs_emit
  fbdev: sm501fb: Convert sysfs snprintf to sysfs_emit
  fbdev: stifb: Fall back to cfb_fillrect() on 32-bit HCRX cards
  fbdev: da8xx-fb: Fix error handling in .remove()
  fbdev: MIPS supports iomem addresses

Pull char/misc fixes from Greg KH:
 "Some small driver fixes for 6.1-rc3.  They include:

   - iio driver bugfixes

   - counter driver bugfixes

   - coresight bugfixes, including a revert and then a second fix to get
     it right.

  All of these have been in linux-next with no reported problems"

* tag 'char-misc-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
  misc: sgi-gru: use explicitly signed char
  coresight: cti: Fix hang in cti_disable_hw()
  Revert "coresight: cti: Fix hang in cti_disable_hw()"
  counter: 104-quad-8: Fix race getting function mode and direction
  counter: microchip-tcb-capture: Handle Signal1 read and Synapse
  coresight: cti: Fix hang in cti_disable_hw()
  coresight: Fix possible deadlock with lock dependency
  counter: ti-ecap-capture: fix IS_ERR() vs NULL check
  counter: Reduce DEFINE_COUNTER_ARRAY_POLARITY() to defining counter_array
  iio: bmc150-accel-core: Fix unsafe buffer attributes
  iio: adxl367: Fix unsafe buffer attributes
  iio: adxl372: Fix unsafe buffer attributes
  iio: at91-sama5d2_adc: Fix unsafe buffer attributes
  iio: temperature: ltc2983: allocate iio channels once
  tools: iio: iio_utils: fix digit calculation
  iio: adc: stm32-adc: fix channel sampling time init
  iio: adc: mcp3911: mask out device ID in debug prints
  iio: adc: mcp3911: use correct id bits
  iio: adc: mcp3911: return proper error code on failure to allocate trigger
  iio: adc: mcp3911: fix sizeof() vs ARRAY_SIZE() bug
  ...

Pull USB fixes from Greg KH:
 "A few small USB fixes for 6.1-rc3. Include in here are:

   - MAINTAINERS update, including a big one for the USB gadget
     subsystem. Many thanks to Felipe for all of the years of hard work
     he has done on this codebase, it was greatly appreciated.

   - dwc3 driver fixes for reported problems.

   - xhci driver fixes for reported problems.

   - typec driver fixes for minor issues

   - uvc gadget driver change, and then revert as it wasn't relevant for
     6.1-final, as it is a new feature and people are still reviewing
     and modifying it.

  All of these have been in the linux-next tree with no reported issues"

* tag 'usb-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: dwc3: gadget: Don't set IMI for no_interrupt
  usb: dwc3: gadget: Stop processing more requests on IMI
  Revert "usb: gadget: uvc: limit isoc_sg to super speed gadgets"
  xhci: Remove device endpoints from bandwidth list when freeing the device
  xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices
  xhci: Add quirk to reset host back to default state at shutdown
  usb: xhci: add XHCI_SPURIOUS_SUCCESS to ASM1042 despite being a V0.96 controller
  usb: dwc3: st: Rely on child's compatible instead of name
  usb: gadget: uvc: limit isoc_sg to super speed gadgets
  usb: bdc: change state when port disconnected
  usb: typec: ucsi: acpi: Implement resume callback
  usb: typec: ucsi: Check the connection on resume
  usb: gadget: aspeed: Fix probe regression
  usb: gadget: uvc: fix sg handling during video encode
  usb: gadget: uvc: fix sg handling in error case
  usb: gadget: uvc: fix dropped frame after missed isoc
  usb: dwc3: gadget: Don't delay End Transfer on delayed_status
  usb: dwc3: Don't switch OTG -> peripheral if extcon is present
  MAINTAINERS: Update maintainers for broadcom USB
  MAINTAINERS: move USB gadget and phy entries under the main USB entry

Pull gpio fixes from Bartosz Golaszewski:

 - convert gpio-tegra to using an immutable irqchip

 - MAINTAINERS update

* tag 'gpio-fixes-for-v6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  MAINTAINERS: Change myself to a maintainer
  gpio: tegra: Convert to immutable irq chip

Pull perf fixes from Borislav Petkov:

 - Rename a perf memory level event define to denote it is of CXL type

 - Add Alder and Raptor Lakes support to RAPL

 - Make sure raw sample data is output with tracepoints

* tag 'perf_urgent_for_v6.1_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/mem: Rename PERF_MEM_LVLNUM_EXTN_MEM to PERF_MEM_LVLNUM_CXL
  perf/x86/rapl: Add support for Intel Raptor Lake
  perf/x86/rapl: Add support for Intel AlderLake-N
  perf: Fix missing raw data on tracepoint events