This patch adds a driver workaround for a HW issue.

A race condition in the HW results in missing interrupts,
which can be avoided by a read/write with the ISR register.
All chips in the AR9002 series are affected by this bug - AR9003
and above do not have this problem.

Cc: stable@vger.kernel.org
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On Fedora systems, unloading rtl8192ce causes an oops. This patch fixes the
problem reported at https://bugzilla.redhat.com/show_bug.cgi?id=852761.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Pick the MAC address of the first virtual interface as the new hardware MAC
address. Set BSSID mask according to this MAC address. This fixes CVE-2013-4579.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Evan Huus found (by fuzzing in wireshark) that the radiotap
iterator code can access beyond the length of the buffer if
the first bitmap claims an extension but then there's no
data at all. Fix this.

Cc: stable@vger.kernel.org
Reported-by: Evan Huus <eapache@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When not aggregating packets, fi->framelen should be passed in as length
to calculate the duration. Before the tx path rework, ath_tx_fill_desc
was called for either one aggregate, or one single frame, with the
length of the packet or the aggregate as a parameter.
After the rework, ath_tx_sched_aggr can pass a burst of single frames to
ath_tx_fill_desc and sets len=0.
Fix broken duration calculation by overriding the length in ath_tx_fill_desc
before passing it to ath_buf_set_rate.

Cc: stable@vger.kernel.org
Reported-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211 allows re-association in managed mode and if a user
wants to re-associate to the same AP network after the time
period of IEEE80211_SCAN_RESULT_EXPIRE, cfg80211 warns with
the following message on receiving the connect result event.

------------[ cut here ]------------
WARNING: CPU: 0 PID: 13984 at net/wireless/sme.c:658
         __cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]()
Call Trace:
 [<ffffffff81747a41>] dump_stack+0x46/0x58
 [<ffffffff81045847>] warn_slowpath_common+0x87/0xb0
 [<ffffffff81045885>] warn_slowpath_null+0x15/0x20
 [<ffffffffa05345f6>] __cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]
 [<ffffffff8107168b>] ? update_rq_clock+0x2b/0x50
 [<ffffffff81078c01>] ? update_curr+0x1/0x160
 [<ffffffffa05133d2>] cfg80211_process_wdev_events+0xb2/0x1c0 [cfg80211]
 [<ffffffff81079303>] ? pick_next_task_fair+0x63/0x170
 [<ffffffffa0513518>] cfg80211_process_rdev_events+0x38/0x90 [cfg80211]
 [<ffffffffa050f03d>] cfg80211_event_work+0x1d/0x30 [cfg80211]
 [<ffffffff8105f21f>] process_one_work+0x17f/0x420
 [<ffffffff8105f90a>] worker_thread+0x11a/0x370
 [<ffffffff8105f7f0>] ? rescuer_thread+0x2f0/0x2f0
 [<ffffffff8106638b>] kthread+0xbb/0xc0
 [<ffffffff810662d0>] ? kthread_create_on_node+0x120/0x120
 [<ffffffff817574bc>] ret_from_fork+0x7c/0xb0
 [<ffffffff810662d0>] ? kthread_create_on_node+0x120/0x120
---[ end trace 61f3bddc9c4981f7 ]---

The reason is that, in connect result event cfg80211 unholds
the BSS to which the device is associated (and was held so
far). So, for the event with status successful, when cfg80211
wants to get that BSS from the device's BSS list it gets a
NULL BSS because the BSS has been expired and unheld already.

Fix it by reshuffling the code.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Building brcmfmac for sparc64 gave the following warning:

  CC [M]  drivers/net/wireless/brcm80211/brcmfmac/bcmsdh_sdmmc.o
    bcmsdh_sdmmc.c: In function 'brcmf_sdioh_request_byte':
     bcmsdh_sdmmc.c:89:6: warning: 'err_ret' may be used uninitialized
                          in this function [-Wuninitialized]

Inspecting the code it indeed had a path of execution in
which the return value was used uninitialized. This patch
fixes that code path.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If kmalloc fails wcn36xx_smd_rsp_process will attempt to dereference
a NULL pointer.  There might be a better error recovery then just
printing an error, but printing an error message is better then the
current behaviour.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Code in ath9k_hw_set_clockrate function indicates that ah->curchan
(and thus chan local variable) may be NULL.  If that is indeed the
case, IS_CHAN_HT40(chan) check has to be performed only in branch
where chan is not NULL.  Moving the code under already existing
if condition fixes this issue.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The EEPROM parameter to determine whether the bias
strength values for XLNA have to be applied is part
of the miscConfiguration field and not featureEnable.

Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bit 5 in the miscConfiguration field of the base EEPROM
header denotes whether QuickDrop is enabled or not. Fix
the incorrect usage of BIT(1) and also make sure that
this is done only for the required chips.

Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When external CSA IEs are received (beacons or action messages), a
channel switch is triggered as well. This should only be allowed on
devices which actually support channel switches, otherwise disconnect.
(For the corresponding userspace invocation, the wiphy flag is checked
in nl80211).
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The channel switch announcement code has some major locking problems
which can cause a deadlock in worst case. A series of fixes has been
proposed, but these are non-trivial and need to be tested first.
Therefore disable CSA completely for 3.13.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If the next seqno returned by the firmware is 0, we return an error
(-16) in the iwl_mvm_get_last_nonqos_seq() function.  This is because
we return an integer and don't use any casting when calculating the
last seqno from the one we received.  Fix this by using a cast to u16
when doing the calculation, so we return 0xfff0, as we should.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In an open BSS, after suspend/resume, we don't set the last seqno
because the iwl_mvm_setup_connection_keep() returns too early.  This
happens because the check to see if we have any keys was returning
immediately, without setting seqno and seqno_valid.  Fix this.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If we call ieee80211_hw_restart, it means that the
firmware is in bad condition and will be reset soon.
Since the firmware will be reset, there is no good
reason to keep sending host commands.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

A new firmware is coming out soon with new APIs.
To make sure that this new firmware won't be loaded on old
driver that don't support it, it's API version has been
updated to 8. In order to be able to load it, bump the API
version to 8.
API version 7 is still supported and will be for another
year or so.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Time event notification can have a failure status even if
the time event was scheduled:
* in START notification, this can happen if the time event
  was scheduled later than the requested apply time.
* in STOP notification, this can happen if the time event
  is truncated.

Even if both happened, the offchannel packets sent during
the remain on channel are very likely to have been sent.
Hence, don't WARN when this happens, but rather print a
discrete line in the kernel log.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>

This patch is very similar to a previous fix: 22cba0c0

When we disassociate, mac80211 removes the station and
then, it sets the bss it unsets the assoc bool in bss_info.

Since the firwmware wants it the opposite (first set the
MAC context as unassoc, and only then, remove the STA of
the API), we have a small period of time in which the STA
in firmware doesn't have a valid ieee80211_sta pointer.
During that time, iwl_mvm_vif->ap_sta_id, is still set
to the STA in firmware that represent the AP.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This feature isn't supported by the firmware (yet).
Note that settingt he values to BT_CFG_CMD is harmless if
the validity bit is clear - so keep the configuration
values in BT_CFG_CMD, but clear the validity bit until thes
feature is enabled in the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add new HW IDs and configurations for 7265 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We changed the timeout for the interrupt coealescing for
calibration, but that wasn't effective since we changed
that value back before loading the firmware. Since
calibrations are notification from firmware and not Rx
packets, this doesn't change anyway - the firmware will
fire an interrupt straight away regardless of the interrupt
coalescing value.
Also, a HW issue has been discovered in 7000 devices series.
The work around is to disable the new interrupt coalescing
timeout feature - do this by setting bit 31 in
CSR_INT_COALESCING.
This has been fixed in 7265 which means that we can't rely
on the device family and must have a hint in the iwl_cfg
structure.

Cc: stable@vger.kernel.org [3.10+]
Fixes: 99cd4714 ("iwlwifi: add 7000 series device configuration")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The station ID must be valid, if it's out of range then
the array access may crash. Validate the station ID to
the array length, and also validate the drain value even
if that doesn't matter all that much.

Cc: stable@vger.kernel.org
Fixes: 8ca151b5 ("iwlwifi: add the MVM driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

For IBSS join if the requested SSID matches current SSID,
it returns without freeing the allocated beacon IE buffer.

Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When building randconfigs with CONFIG_BCMA_DRIVER_GPIO=y, I get

drivers/built-in.o: In function `brcms_led_unregister':
(.text+0x351aca): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `brcms_led_register':
(.text+0x351c65): undefined reference to `led_classdev_register'

during final linking stage because brcmsmac/led.c needs LEDS_CLASS for
registering/deregistering the led device. Select the required symbols.

Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Rafał Miłecki" <zajec5@gmail.com>
Cc: <linux-wireless@vger.kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ATM, the first call of ieee80211_do_open will configure the hw as
non-idle, even if the interface being brought up is not a monitor, and
this leads to inconsistent sequences like:

register_hw()
	do_open(sta)
		hw_config(non-idle)
(.. sta is non-idle ..)
scan(sta)
	hw_config(idle) (after scan finishes)
do_stop(sta)
do_open(sta)
(.. sta is idle ..)
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Commit 3e8b1eb2 "mac80211/minstrel_ht: improve rate selection stability"
introduced a local capped prob in minstrel_ht_calc_tp but omitted to use
it to compute the per rate throughput.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Fixes wpa_supplicant p2p_find on 5GHz-only devices
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Commit 392b9ffb ("mac80211: change beacon/connection polling")
removed the IEEE80211_STA_BEACON_POLL flag.

However, it accidentally removed the setting of
IEEE80211_STA_CONNECTION_POLL, making the connection polling
completely useless (the flag is always clear, so the result
is never being checked). Fix it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

'mac80211_hwsim: Fix tracking of beaconing for multi-vif' introduced an
iteration of active interfaces into the bss_info_changed handler.
However, it used a wrong type of iteration and could result in a dead
lock since iflist_mtx can already be held. Fix this by using the atomic
version of the iteration function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Mesh STA receiving the mesh CSA action frame is not able to trigger
the mesh channel switch due to the incorrect handling and comparison
of mesh channel switch parameters element (MCSP)'s TTL. Make sure
the MCSP's TTL is updated accordingly before calling the
ieee80211_mesh_process_chnswitch. Also, we update the beacon before
forwarding the CSA action frame, so MCSP's precedence value and
initiator flag need to be updated prior to this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Multicast frames can't be transmitted as part of an aggregation
session (such a session couldn't even be set up) so don't try to
reorder them. Trying to do so would cause the reorder to stop
working correctly since multicast QoS frames (as transmitted by
the Aruba APs this was found with) would cause sequence number
confusion in the buffer.

Cc: stable@vger.kernel.org
Reported-by: Blaise Gassend <blaise@suitabletech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Due to nl80211 API breakage, 5/10 MHz support is broken for
all drivers. Fixing it requires adding new API, but that
can't be done as a bugfix commit since that would require
either updating all APIs in the trees needing the bugfix or
cause different kernels to have incompatible API.

Therefore, just disable 5/10 MHz support for all drivers.

Cc: stable@vger.kernel.org [3.12]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When initializing rates selections starting indexes upon stats update,
the minstrel_sta->max_* rates should be 'group * MCS_GROUP_RATES + i'
not 'i'. This affects settings where one of the peers does not support
any of the rates of the group 0 (i.e. when ht_cap.mcs.rx_mask[0] == 0).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Mesh beacon was not being rebuild after user triggered a mesh
powersave change.

To solve this issue use ieee80211_mbss_info_change_notify instead
of ieee80211_bss_info_change_notify. This helper function forces
mesh beacon to be rebuild and then notifies the driver about the
beacon change.
Signed-off-by: Javier Lopez <jlopex@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Commit "mac80211: implement SMPS for AP" applies to AP_VLAN as well.
It assumes that sta->sdata->vif.bss_conf.bssid is present, which did not
get set for AP_VLAN.
Initialize it to sdata->vif.addr like for other interface types.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>