Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In multi channel context (AP + STA case), adjust the TSF time of
the AP chanctx to keep its beacons at half beacon interval offset
relative to the STA chanctx.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update current offchannel duration during scan or roc request.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a basic state machine for switch channel context
for beacon transmission.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Save TSF in channel context for multiple operating channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Retrieve appropriate operating channel context while switching
between operating and off channels.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add channel context operations (add, remove, change, assign and
unassign) to enable support for multiple channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add remain on channel support in order to enable multi-channel
concurrency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Implement hw_scan support for enabling multi-channel cuncurrency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While leaving from or entering to active channel context, send out
nullfunc frame to inform to the AP about the presence of station.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Force queueing of all frames that belong to a virtual interface on
a different channel context, to ensure that they are sent on the
correct channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The channel context worker is used to switch to next requested
channel context.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add support to maintain per-channel ACs list.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The channel context structure is defined to enable
multi-channel concurrency support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since CL_PRINTF only ever takes a single argument, make sure a format
string cannot leak into printk.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix rsi_module_init() to propagate sdio_register_driver() errors.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

module_usb_driver eliminates the boilerplate and makes the code simpler,
in addition to the fact currently rsi_module_init() ignores usb_deregister() error.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For users who do not need wowlan, load mwifiex.ko with
disconnect_on_suspend = 1; or iw phy0 wowlan disable.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When magic-packet is generated as a UDP packet the offset should
be 20+8 more bytes to cover IPv4 header and UDP header. So the
total offset become 56.
Add a new MEF entry to support both magic-packet patterns
generated by different tools.

Cc: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Zhiyuan Yang <yangzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I've here a device detected as:
bcma: bus0: Found chip with id 0xD144, rev 0x01 and package 0x08
I couldn't find GPIO handling hw button until trying GPIO 20. It seems
BCM53572 also has 32 GPIOs.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We setup BCN_OFFSET{0,1} registers dynamically, don't have to
initialize them.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When no beaconing is needed, first stop beacon queue (disable beaconing
globally) to avoid possible sending of not prepared beacon on short
period after clearing beacon and before stop of BCN queue.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We setup MAC_BSSID_DW1_BSS_BCN_NUM dynamically when numbers of active
beacons increase. Change default to 0 to tell hardware that we want to
send only one beacon as default.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As reported by Matthias, on 5572 chip, even if we clear up TXWI
of corresponding beacon, hardware still try to send it or do other
action that increase power consumption peak up to 1A.

To avoid the issue, setup beaconing dynamically by configuring offsets
of currently active beacons and MAC_BSSID_DW1_BSS_BCN_NUM variable,
which limit number of beacons that hardware will try to send.
Reported-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch is needed for further changes to keep global variables
consistent when changing beaconing on diffrent vif's.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A custom regulatory domain was introduced in this commit:
cc0ba0d mwifiex: support custom world regulatory domain

The commit description says that it was introduced because the world
regulatory domain does not include channels 52-64 and 100-140. These
channels are described in the world regulatory domain now, so we can
drop this custom regulatory domain.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is a risk that the variables will be used without being initialized.
Have also moved variable to the part of the code where it is used.

This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is a risk that the variable will be used without being initialized.

This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is a risk that the variable will be used without being initialized.

This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>