- 10 Feb, 2017 3 commits
-
-
Boris Ostrovsky authored
rx_refill_timer should be deleted as soon as we disconnect from the backend since otherwise it is possible for the timer to go off before we get to xennet_destroy_queues(). If this happens we may dereference queue->rx.sring which is set to NULL in xennet_disconnect_backend(). Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> CC: stable@vger.kernel.org Reviewed-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ralf Baechle authored
If a USB-to-serial adapter is unplugged, the driver re-initializes, with dev->hard_header_len and dev->addr_len set to zero, instead of the correct values. If then a packet is sent through the half-dead interface, the kernel will panic due to running out of headroom in the skb when pushing for the AX.25 headers resulting in this panic: [<c0595468>] (skb_panic) from [<c0401f70>] (skb_push+0x4c/0x50) [<c0401f70>] (skb_push) from [<bf0bdad4>] (ax25_hard_header+0x34/0xf4 [ax25]) [<bf0bdad4>] (ax25_hard_header [ax25]) from [<bf0d05d4>] (ax_header+0x38/0x40 [mkiss]) [<bf0d05d4>] (ax_header [mkiss]) from [<c041b584>] (neigh_compat_output+0x8c/0xd8) [<c041b584>] (neigh_compat_output) from [<c043e7a8>] (ip_finish_output+0x2a0/0x914) [<c043e7a8>] (ip_finish_output) from [<c043f948>] (ip_output+0xd8/0xf0) [<c043f948>] (ip_output) from [<c043f04c>] (ip_local_out_sk+0x44/0x48) This patch makes mkiss behave like the 6pack driver. 6pack does not panic. In 6pack.c sp_setup() (same function name here) the values for dev->hard_header_len and dev->addr_len are set to the same values as in my mkiss patch. [ralf@linux-mips.org: Massages original submission to conform to the usual standards for patch submissions.] Signed-off-by:
Thomas Osterried <thomas@osterried.de> Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Kejian Yan authored
This patch fixes the device being used to DMA map skb->data. Erroneous device assignment causes the crash when SMMU is enabled. This happens during TX since buffer gets DMA mapped with device correspondign to net_device and gets unmapped using the device related to DSAF. Signed-off-by:
Kejian Yan <yankejian@huawei.com> Reviewed-by:
Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by:
Salil Mehta <salil.mehta@huawei.com> Signed-off-by:
-
- 09 Feb, 2017 9 commits
-
-
Yendapally Reddy Dhananjaya Reddy authored
USB PHYs need the MDIO clock divisor enabled earlier to work. Initialize mdio clock divisor in probe function. The ext bus bit available in the same register will be used by mdio mux to enable external mdio. Signed-off-by:
Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver") Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Jon Mason <jon.mason@broadcom.com> Signed-off-by:
-
Hangbin Liu authored
In function igmpv3/mld_add_delrec() we allocate pmc and put it in idev->mc_tomb, so we should free it when we don't need it in del_delrec(). But I removed kfree(pmc) incorrectly in latest two patches. Now fix it. Fixes: 24803f38 ("igmp: do not remove igmp souce list info when ...") Fixes: 1666d49e ("mld: do not remove mld souce list info when ...") Reported-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Signed-off-by:
-
Ross Lagerwall authored
This fixes a crash when running out of grant refs when creating many queues across many netdevs. * If creating queues fails (i.e. there are no grant refs available), call xenbus_dev_fatal() to ensure that the xenbus device is set to the closed state. * If no queues are created, don't call xennet_disconnect_backend as netdev->real_num_tx_queues will not have been set correctly. * If setup_netfront() fails, ensure that all the queues created are cleaned up, not just those that have been set up. * If any queues were set up and an error occurs, call xennet_destroy_queues() to clean up the napi context. * If any fatal error occurs, unregister and destroy the netdev to avoid leaving around a half setup network device. Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by:
-
David S. Miller authored
Stefan Brüns says: ==================== Fixes for sierra_net driver When trying to initiate a dual-stack (ipv4v6) connection, a MC7710, FW version SWI9200X_03.05.24.00ap answers with an unsupported LSI. Add support for this LSI. Also the link_type should be ignored when going idle, otherwise the modem is stuck in a bad link state. Tested on MC7710, T-Mobile DE, APN internet.telekom, IPv4v6 PDP type. Both IPv4 and IPv6 connections work. v2: Do not overwrite protocol field in rx_fixup v3: Remove leftover struct ethhdr *eth declaration ==================== Signed-off-by: -
Stefan Brüns authored
When the context is deactivated, the link_type is set to 0xff, which triggers a warning message, and results in a wrong link status, as the LSI is ignored. Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by:
-
Stefan Brüns authored
If a context is configured as dualstack ("IPv4v6"), the modem indicates the context activation with a slightly different indication message. The dual-stack indication omits the link_type (IPv4/v6) and adds additional address fields. IPv6 LSIs are identical to IPv4 LSIs, but have a different link type. Signed-off-by:Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
WANG Cong authored
Dmitry reported a kernel warning: WARNING: CPU: 3 PID: 2936 at net/kcm/kcmsock.c:627 kcm_write_msgs+0x12e3/0x1b90 net/kcm/kcmsock.c:627 CPU: 3 PID: 2936 Comm: a.out Not tainted 4.10.0-rc6+ #209 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:15 [inline] dump_stack+0x2ee/0x3ef lib/dump_stack.c:51 panic+0x1fb/0x412 kernel/panic.c:179 __warn+0x1c4/0x1e0 kernel/panic.c:539 warn_slowpath_null+0x2c/0x40 kernel/panic.c:582 kcm_write_msgs+0x12e3/0x1b90 net/kcm/kcmsock.c:627 kcm_sendmsg+0x163a/0x2200 net/kcm/kcmsock.c:1029 sock_sendmsg_nosec net/socket.c:635 [inline] sock_sendmsg+0xca/0x110 net/socket.c:645 sock_write_iter+0x326/0x600 net/socket.c:848 new_sync_write fs/read_write.c:499 [inline] __vfs_write+0x483/0x740 fs/read_write.c:512 vfs_write+0x187/0x530 fs/read_write.c:560 SYSC_write fs/read_write.c:607 [inline] SyS_write+0xfb/0x230 fs/read_write.c:599 entry_SYSCALL_64_fastpath+0x1f/0xc2 when calling syscall(__NR_write, sock2, 0x208aaf27ul, 0x0ul) on a KCM seqpacket socket. It appears that kcm_sendmsg() does not handle len==0 case correctly, which causes an empty skb is allocated and queued. Fix this by skipping the skb allocation for len==0 case. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Cc: Tom Herbert <tom@herbertland.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Vineeth Remanan Pillai authored
The commit 90c311b0 ("xen-netfront: Fix Rx stall during network stress and OOM") caused the refill timer to be triggerred almost on all invocations of xennet_alloc_rx_buffers for certain workloads. This reworks the fix by reverting to the old behaviour and taking into consideration the skb allocation failure. Refill timer is now triggered on insufficient requests or skb allocation failure. Signed-off-by:
Vineeth Remanan Pillai <vineethp@amazon.com> Fixes: 90c311b0 (xen-netfront: Fix Rx stall during network stress and OOM) Reported-by:
-
Florian Fainelli authored
The Generic PHY drivers gets assigned after we checked that the current PHY driver is NULL, so we need to check a few things before we can safely dereference d->driver. This would be causing a NULL deference to occur when a system binds to the Generic PHY driver. Update phy_attach_direct() to do the following: - grab the driver module reference after we have assigned the Generic PHY drivers accordingly, and remember we came from the generic PHY path - update the error path to clean up the module reference in case the Generic PHY probe function fails - split the error path involving phy_detacht() to avoid double free/put since phy_detach() does all the clean up - finally, have phy_detach() drop the module reference count before we call device_release_driver() for the Generic PHY driver case Fixes: cafe8df8 ("net: phy: Fix lack of reference count on PHY driver") Signed-off-by:
-
- 08 Feb, 2017 9 commits
-
-
Thanneeru Srinivasulu authored
This patch fixes the case where there is no phydev attached to a LMAC in DT due to non-existance of a PHY driver or due to usage of non-stanadard PHY which doesn't support autoneg. Changes dependeds on firmware to send correct info w.r.t PHY and autoneg capability. This patch also covers a case where a 10G/40G interface is used as a 1G with convertors with Cortina PHY in between. Signed-off-by:
Thanneeru Srinivasulu <tsrinivasulu@cavium.com> Signed-off-by:
Sunil Goutham <sgoutham@cavium.com> Signed-off-by:
-
Florian Fainelli authored
dsa_slave_create() can fail, and dsa_user_port_unapply() will properly check for the network device not being NULL before attempting to destroy it. We were not setting the slave network device as NULL if dsa_slave_create() failed, so we would later on be calling dsa_slave_destroy() on a now free'd and unitialized network device, causing crashes in dsa_slave_destroy(). Fixes: 83c0afae ("net: dsa: Add new binding implementation") Signed-off-by:
-
WANG Cong authored
Andrey reported a kernel crash: general protection fault: 0000 [#1] SMP KASAN Dumping ftrace buffer: (ftrace buffer empty) Modules linked in: CPU: 2 PID: 3880 Comm: syz-executor1 Not tainted 4.10.0-rc6+ #124 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 task: ffff880060048040 task.stack: ffff880069be8000 RIP: 0010:ping_v4_push_pending_frames net/ipv4/ping.c:647 [inline] RIP: 0010:ping_v4_sendmsg+0x1acd/0x23f0 net/ipv4/ping.c:837 RSP: 0018:ffff880069bef8b8 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: ffff880069befb90 RCX: 0000000000000000 RDX: 0000000000000018 RSI: ffff880069befa30 RDI: 00000000000000c2 RBP: ffff880069befbb8 R08: 0000000000000008 R09: 0000000000000000 R10: 0000000000000002 R11: 0000000000000000 R12: ffff880069befab0 R13: ffff88006c624a80 R14: ffff880069befa70 R15: 0000000000000000 FS: 00007f6f7c716700(0000) GS:ffff88006de00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000004a6f28 CR3: 000000003a134000 CR4: 00000000000006e0 Call Trace: inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:744 sock_sendmsg_nosec net/socket.c:635 [inline] sock_sendmsg+0xca/0x110 net/socket.c:645 SYSC_sendto+0x660/0x810 net/socket.c:1687 SyS_sendto+0x40/0x50 net/socket.c:1655 entry_SYSCALL_64_fastpath+0x1f/0xc2 This is because we miss a check for NULL pointer for skb_peek() when the queue is empty. Other places already have the same check. Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind") Reported-by:Andrey Konovalov <andreyknvl@google.com> Tested-by:
-
David S. Miller authored
Willem de Bruijn says: ==================== net: Fixes for header length truncation Packets should not enter the stack with truncated link layer headers and link layer headers should always be stored in the skb linear segment. Patch 1 ensures the first for PF_PACKET sockets Patch 2 ensures the second for PF_PACKET GSO sockets without tx_ring ==================== Signed-off-by: -
Willem de Bruijn authored
Link layer protocols may unconditionally pull headers, as Ethernet does in eth_type_trans. Ensure that the entire link layer header always lies in the skb linear segment. tpacket_snd has such a check. Extend this to packet_snd. Variable length link layer headers complicate the computation somewhat. Here skb->len may be smaller than dev->hard_header_len. Round up the linear length to be at least as long as the smallest of the two. Reported-by:
Willem de Bruijn <willemb@google.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Willem de Bruijn authored
The stack must not pass packets to device drivers that are shorter than the minimum link layer header length. Previously, packet sockets would drop packets smaller than or equal to dev->hard_header_len, but this has false positives. Zero length payload is used over Ethernet. Other link layer protocols support variable length headers. Support for validation of these protocols removed the min length check for all protocols. Introduce an explicit dev->min_header_len parameter and drop all packets below this value. Initially, set it to non-zero only for Ethernet and loopback. Other protocols can follow in a patch to net-next. Fixes: 9ed988cd ("packet: validate variable length ll headers") Reported-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by:
-
WANG Cong authored
Dmitry reported a double free in sit_init_net(): kernel BUG at mm/percpu.c:689! invalid opcode: 0000 [#1] SMP KASAN Dumping ftrace buffer: (ftrace buffer empty) Modules linked in: CPU: 0 PID: 15692 Comm: syz-executor1 Not tainted 4.10.0-rc6-next-20170206 #1 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 task: ffff8801c9cc27c0 task.stack: ffff88017d1d8000 RIP: 0010:pcpu_free_area+0x68b/0x810 mm/percpu.c:689 RSP: 0018:ffff88017d1df488 EFLAGS: 00010046 RAX: 0000000000010000 RBX: 00000000000007c0 RCX: ffffc90002829000 RDX: 0000000000010000 RSI: ffffffff81940efb RDI: ffff8801db841d94 RBP: ffff88017d1df590 R08: dffffc0000000000 R09: 1ffffffff0bb3bdd R10: dffffc0000000000 R11: 00000000000135dd R12: ffff8801db841d80 R13: 0000000000038e40 R14: 00000000000007c0 R15: 00000000000007c0 FS: 00007f6ea608f700(0000) GS:ffff8801dbe00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000002000aff8 CR3: 00000001c8d44000 CR4: 00000000001426f0 DR0: 0000000020000000 DR1: 0000000020000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000600 Call Trace: free_percpu+0x212/0x520 mm/percpu.c:1264 ipip6_dev_free+0x43/0x60 net/ipv6/sit.c:1335 sit_init_net+0x3cb/0xa10 net/ipv6/sit.c:1831 ops_init+0x10a/0x530 net/core/net_namespace.c:115 setup_net+0x2ed/0x690 net/core/net_namespace.c:291 copy_net_ns+0x26c/0x530 net/core/net_namespace.c:396 create_new_namespaces+0x409/0x860 kernel/nsproxy.c:106 unshare_nsproxy_namespaces+0xae/0x1e0 kernel/nsproxy.c:205 SYSC_unshare kernel/fork.c:2281 [inline] SyS_unshare+0x64e/0xfc0 kernel/fork.c:2231 entry_SYSCALL_64_fastpath+0x1f/0xc2 This is because when tunnel->dst_cache init fails, we free dev->tstats once in ipip6_tunnel_init() and twice in sit_init_net(). This looks redundant but its ndo_uinit() does not seem enough to clean up everything here. So avoid this by setting dev->tstats to NULL after the first free, at least for -net. Reported-by: -
David Ahern authored
An error was reported upgrading to 4.9.8: root@Typhoon:~# ip route add default table 210 nexthop dev eth0 via 10.68.64.1 weight 1 nexthop dev eth0 via 10.68.64.2 weight 1 RTNETLINK answers: Operation not supported The problem occurs when CONFIG_LWTUNNEL is not enabled and a multipath route is submitted. The point of lwtunnel_valid_encap_type_attr is catch modules that need to be loaded before any references are taken with rntl held. With CONFIG_LWTUNNEL disabled, there will be no modules to load so the lwtunnel_valid_encap_type_attr stub should just return 0. Fixes: 9ed59592 ("lwtunnel: fix autoload of lwt modules") Reported-by: pupilla@libero.it Signed-off-by:David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
Marcus Huewe authored
Under some circumstances it is possible that no new temporary addresses will be generated. For instance, addrconf_prefix_rcv_add_addr() indirectly calls ipv6_create_tempaddr(), which creates a tentative temporary address and starts dad. Next, addrconf_prefix_rcv_add_addr() indirectly calls addrconf_verify_rtnl(). Now, assume that the previously created temporary address has the least preferred lifetime among all existing addresses and is still tentative (that is, dad is still running). Hence, the next run of addrconf_verify_rtnl() is performed when the preferred lifetime of the temporary address ends. If dad succeeds before the next run, the temporary address becomes deprecated during the next run, but no new temporary address is generated. In order to fix this, schedule the next addrconf_verify_rtnl() run slightly before the temporary address becomes deprecated, if dad succeeded. Signed-off-by:
Marcus Huewe <suse-tux@gmx.de> Signed-off-by:
-
- 07 Feb, 2017 17 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Load correct firmware in rtl8192ce wireless driver, from Jurij Smakov. 2) Fix leak of tx_ring and tx_cq due to overwriting in mlx4 driver, from Martin KaFai Lau. 3) Need to reference count PHY driver module when it is attached, from Mao Wenan. 4) Don't do zero length vzalloc() in ethtool register dump, from Stanislaw Gruszka. 5) Defer net_disable_timestamp() to a workqueue to get out of locking issues, from Eric Dumazet. 6) We cannot drop the SKB dst when IP options refer to them, fix also from Eric Dumazet. 7) Incorrect packet header offset calculations in ip6_gre, again from Eric Dumazet. 8) Missing tcp_v6_restore_cb() causes use-after-free, from Eric too. 9) tcp_splice_read() can get into an infinite loop with URG, and hey it's from Eric once more. 10) vnet_hdr_sz can change asynchronously, so read it once during decision making in macvtap and tun, from Willem de Bruijn. 11) Can't use kernel stack for DMA transfers in USB networking drivers, from Ben Hutchings. 12) Handle csum errors properly in UDP by calling the proper destructor, from Eric Dumazet. 13) For non-deterministic softirq run when scheduling NAPI from a workqueue in mlx4, from Benjamin Poirier. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits) sctp: check af before verify address in sctp_addr_id2transport sctp: avoid BUG_ON on sctp_wait_for_sndbuf mlx4: Invoke softirqs after napi_reschedule udp: properly cope with csum errors catc: Use heap buffer for memory size test catc: Combine failure cleanup code in catc_probe() rtl8150: Use heap buffers for all register access pegasus: Use heap buffers for all register access macvtap: read vnet_hdr_size once tun: read vnet_hdr_sz once tcp: avoid infinite loop in tcp_splice_read() hns: avoid stack overflow with CONFIG_KASAN ipv6: Fix IPv6 packet loss in scenarios involving roaming + snooping switches ipv6: tcp: add a missing tcp_v6_restore_cb() nl80211: Fix mesh HT operation check mac80211: Fix adding of mesh vendor IEs mac80211: Allocate a sync skcipher explicitly for FILS AEAD mac80211: Fix FILS AEAD protection in Association Request frame ip6_gre: fix ip6gre_err() invalid reads netlabel: out of bound access in cipso_v4_validate() ... -
Hugh Dickins authored
Commit 6326fec1 ("mm: Use owner_priv bit for PageSwapCache, valid when PageSwapBacked") aliased PG_swapcache to PG_owner_priv_1 (and depending on PageSwapBacked being true). As a result, the KPF_SWAPCACHE bit in '/proc/kpageflags' should now be synthesized, instead of being shown on unrelated pages which just happen to have PG_owner_priv_1 set. Signed-off-by:
Hugh Dickins <hughd@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Xin Long authored
Commit 6f29a130 ("sctp: sctp_addr_id2transport should verify the addr before looking up assoc") invoked sctp_verify_addr to verify the addr. But it didn't check af variable beforehand, once users pass an address with family = 0 through sockopt, sctp_get_af_specific will return NULL and NULL pointer dereference will be caused by af->sockaddr_len. This patch is to fix it by returning NULL if af variable is NULL. Fixes: 6f29a130 ("sctp: sctp_addr_id2transport should verify the addr before looking up assoc") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Vineet Gupta authored
Reported-by:
Jo-Philipp Wich <jo@mein.io> Fixes: 9aed02fe ("ARC: [arcompact] handle unaligned access delay slot") Cc: linux-kernel@vger.kernel.org Cc: linux-snps-arc@lists.infradead.org Cc: stable@vger.kernel.org Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Marcelo Ricardo Leitner authored
Alexander Popov reported that an application may trigger a BUG_ON in sctp_wait_for_sndbuf if the socket tx buffer is full, a thread is waiting on it to queue more data and meanwhile another thread peels off the association being used by the first thread. This patch replaces the BUG_ON call with a proper error handling. It will return -EPIPE to the original sendmsg call, similarly to what would have been done if the association wasn't found in the first place. Acked-by:
Alexander Popov <alex.popov@linux.com> Signed-off-by:
-
Benjamin Poirier authored
mlx4 may schedule napi from a workqueue. Afterwards, softirqs are not run in a deterministic time frame and the following message may be logged: NOHZ: local_softirq_pending 08 The problem is the same as what was described in commit ec13ee80 ("virtio_net: invoke softirqs after __napi_schedule") and this patch applies the same fix to mlx4. Fixes: 07841f9d ("net/mlx4_en: Schedule napi when RX buffers allocation fails") Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
Benjamin Poirier <bpoirier@suse.com> Acked-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Eric Dumazet authored
Dmitry reported that UDP sockets being destroyed would trigger the WARN_ON(atomic_read(&sk->sk_rmem_alloc)); in inet_sock_destruct() It turns out we do not properly destroy skb(s) that have wrong UDP checksum. Thanks again to syzkaller team. Fixes : 7c13f97f ("udp: do fwd memory scheduling on dequeue") Reported-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
David S. Miller authored
Ben Hutchings says: ==================== net: Fix on-stack USB buffers Allocating USB buffers on the stack is not portable, and no longer works on x86_64 (with VMAP_STACK enabled as per default). This series fixes all the instances I could find where USB networking drivers do that. ==================== Signed-off-by: -
Ben Hutchings authored
Allocating USB buffers on the stack is not portable, and no longer works on x86_64 (with VMAP_STACK enabled as per default). Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
-
Ben Hutchings authored
Allocating USB buffers on the stack is not portable, and no longer works on x86_64 (with VMAP_STACK enabled as per default). Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Ben Hutchings authored
Allocating USB buffers on the stack is not portable, and no longer works on x86_64 (with VMAP_STACK enabled as per default). Fixes: 1da177e4 ("Linux-2.6.12-rc2") References: https://bugs.debian.org/852556Reported-by:
Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org> Tested-by:
-
David S. Miller authored
Willem de Bruijn says: ==================== read vnet_hdr_sz once Tuntap devices allow concurrent use and update of field vnet_hdr_sz. Read the field once to avoid TOCTOU. ==================== Signed-off-by: -
Willem de Bruijn authored
When IFF_VNET_HDR is enabled, a virtio_net header must precede data. Data length is verified to be greater than or equal to expected header length tun->vnet_hdr_sz before copying. Macvtap functions read the value once, but unless READ_ONCE is used, the compiler may ignore this and read multiple times. Enforce a single read and locally cached value to avoid updates between test and use. Signed-off-by:
-
Willem de Bruijn authored
When IFF_VNET_HDR is enabled, a virtio_net header must precede data. Data length is verified to be greater than or equal to expected header length tun->vnet_hdr_sz before copying. Read this value once and cache locally, as it can be updated between the test and use (TOCTOU). Signed-off-by:
-
Eric Dumazet authored
Splicing from TCP socket is vulnerable when a packet with URG flag is received and stored into receive queue. __tcp_splice_read() returns 0, and sk_wait_data() immediately returns since there is the problematic skb in queue. This is a nice way to burn cpu (aka infinite loop) and trigger soft lockups. Again, this gem was found by syzkaller tool. Fixes: 9c55e01c ("[TCP]: Splice receive support.") Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimmLinus Torvalds authored
Pull libnvdimm fixes from Dan Williams: "None of these are showstoppers for 4.10 and could wait for 4.11 merge window, but they are low enough risk for this late in the cycle and the fixes have waiting users . They have received a build success notification from the 0day robot, pass the latest ndctl unit tests, and appeared in next: - Fix a crash that can result when SIGINT is sent to a process that is awaiting completion of an address range scrub command. We were not properly cleaning up the workqueue after wait_event_interruptible(). - Fix a memory hotplug failure condition that results from not reserving enough space out of persistent memory for the memmap. By default we align to 2M allocations that the memory hotplug code assumes, but if the administrator specifies a non-default 4K-alignment then we can fail to correctly size the reservation. - A one line fix to improve the predictability of libnvdimm block device names. A common operation is to reconfigure /dev/pmem0 into a different mode. For example, a reconfiguration might set a new mode that reserves some of the capacity for a struct page memmap array. It surprises users if the device name changes to "/dev/pmem0.1" after the mode change and then back to /dev/pmem0 after a reboot. - Add 'const' to some function pointer tables" * 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: libnvdimm, pfn: fix memmap reservation size versus 4K alignment acpi, nfit: fix acpi_nfit_flush_probe() crash libnvdimm, namespace: do not delete namespace-id 0 nvdimm: constify device_type structures
-
- 06 Feb, 2017 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull power management fixes from Rafael Wysocki: "These add a quirk to intel_pstate to work around a firmware setting that leads to frequency scaling issues (discovered recently) on some Intel Kaby Lake processors, fix up the recently added brcmstb-avs cpufreq driver and avoid false-positive warnings from the runtime PM framework triggered by recent changes in i915. Specifics: - Add an intel_pstate driver quirk to work around a firmware setting that leads to frequency scaling issues on desktop Intel Kaby Lake processors in some configurations if the hardware-managed P-states (HWP) feature is in use (Srinivas Pandruvada) - Fix up the recently added brcmstb-avs cpufreq driver: fix a bug related to system suspend and change the sysfs interface to match the user space expectations (Markus Mayer) - Modify the runtime PM framework to avoid false-positive warnings from the might_sleep_if() assertions in it (Rafael Wysocki)" * tag 'pm-4.10-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: PM / runtime: Avoid false-positive warnings from might_sleep_if() cpufreq: intel_pstate: Disable energy efficiency optimization cpufreq: brcmstb-avs-cpufreq: properly retrieve P-state upon suspend cpufreq: brcmstb-avs-cpufreq: extend sysfs entry brcm_avs_pmap -
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dmLinus Torvalds authored
Pull device mapper fixes from Mike Snitzer: - a fix for a race in .request_fn request-based DM request handling vs DM device destruction - an RCU fix for dm-crypt's kernel keyring support that was included in 4.10-rc1 - a -Wbool-operation warning fix for DM multipath * tag 'dm-4.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: dm crypt: replace RCU read-side section with rwsem dm rq: cope with DM device destruction while in dm_old_request_fn() dm mpath: cleanup -Wbool-operation warning in choose_pgpath()
-
