[Why]
Fix for some of the tool reported modes for FCLK
P-state deviations and UCLK P-state deviations that
are coming from DSC terms and/or Scaling terms
causing MinActiveFCLKChangeLatencySupported
and MaxActiveDRAMClockChangeLatencySupported
incorrectly calculated in DML for these configurations.
Reviewed-by: Chaitanya Dhere <Chaitanya.Dhere@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Certain 4K high refresh rate modes requiring DSC are exhibiting top
of screen underflow corruption. Increasing the DSC delay by a factor
of 6 percent stops the underflow for most use cases.

[How]
Multiply DSC delay requirement in DML by a factor.
Add debug option to make this DSC delay factor configurable.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
The DST_after_scaler value that DML spreadsheet outputs is
generally the driver value round up to the nearest int.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DSC config is calculated separately from DML calculations.
DML should use these separately calculated DSC params. The issue is
that the calculated bpp is not properly propagated into DML.

[How]
Correctly used forced_bpp value in DML.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCN32 DSC delay calculation had an unintentional integer division,
resulting in a mismatch against the DML spreadsheet.

[How]
Cast numerator to double before performing the division.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The recent change brought a bug on SRIOV envrionment. It caused
unloading amdgpu failed on Guest VM. The reason is that the VF
FLR was requested while unloading amdgpu driver, but the VF FLR
of SRIOV sequence is wrong while removing PCI device.

For SRIOV, the guest driver should not trigger the whole XGMI hive
to do the reset. Host driver control how the device been reset.

Fixes: f5c7e779 ("drm/amdgpu: Adjust removal control flow for smu v13_0_2")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Gavin Wan <Gavin.Wan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Temporary workaround to fix issues observed in some compute applications
when GFXOFF is enabled on GFX11.
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x

If a system does not have swap and memory is under 100% usage,
amdgpu will fail to evict resources.  Currently the suspend
carries on proceeding to reset the GPU:

```
[drm] evicting device resources failed
[drm:amdgpu_device_ip_suspend_phase2 [amdgpu]] *ERROR* suspend of IP block <vcn_v3_0> failed -12
[drm] free PSP TMR buffer
[TTM] Failed allocating page table
[drm] evicting device resources failed
amdgpu 0000:03:00.0: amdgpu: MODE1 reset
amdgpu 0000:03:00.0: amdgpu: GPU mode1 reset
amdgpu 0000:03:00.0: amdgpu: GPU smu mode1 reset
```

At this point if the suspend actually succeeded I think that amdgpu
would have recovered because the GPU would have power cut off and
restored.  However the kernel fails to continue the suspend from the
memory pressure and amdgpu fails to run the "resume" from the aborted
suspend.

```
ACPI: PM: Preparing to enter system sleep state S3
SLUB: Unable to allocate memory on node -1, gfp=0xdc0(GFP_KERNEL|__GFP_ZERO)
  cache: Acpi-State, object size: 80, buffer size: 80, default order: 0, min order: 0
  node 0: slabs: 22, objs: 1122, free: 0
ACPI Error: AE_NO_MEMORY, Could not update object reference count (20210730/utdelete-651)

[drm:psp_hw_start [amdgpu]] *ERROR* PSP load kdb failed!
[drm:psp_resume [amdgpu]] *ERROR* PSP resume failed
[drm:amdgpu_device_fw_loading [amdgpu]] *ERROR* resume of IP block <psp> failed -62
amdgpu 0000:03:00.0: amdgpu: amdgpu_device_ip_resume failed (-62).
PM: dpm_run_callback(): pci_pm_resume+0x0/0x100 returns -62
amdgpu 0000:03:00.0: PM: failed to resume async: error -62
```

To avoid this series of unfortunate events, fail amdgpu's suspend
when the memory eviction fails.  This will let the system gracefully
recover and the user can try suspend again when the memory pressure
is relieved.

Reported-by: post@davidak.de
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2223Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

./drivers/gpu/drm/amd/amdkfd/kfd_migrate.c:985:58-62: ERROR: p is NULL but dereferenced.

Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2549Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Use mes.sched_version, mes.kiq_version for debugfs as
mes.ucode_fw_version does not contain correct versioning information.
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch to fix the gdm3 start failure with virual display:

/usr/libexec/gdm-x-session[1711]: (II) AMDGPU(0): Setting screen physical size to 270 x 203
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): Failed to make import prime FD as pixmap: 22
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): failed to set mode: Invalid argument
/usr/libexec/gdm-x-session[1711]: (WW) AMDGPU(0): Failed to set mode on CRTC 0
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): Failed to enable any CRTC
gnome-shell[1840]: Running GNOME Shell (using mutter 42.2) as a X11 window and compositing manager
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): failed to set mode: Invalid argument

vkms doesn't have modifiers support, set fb_modifiers_not_supported to bring the gdm back.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tim Huang <Tim.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Missing send cursor_rect width & Height into DMUB. PSR-SU would use
these information. But missing these assignment in last refactor commit
Reported-by: Timur Kristóf <timur.kristof@gmail.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2227
Fixes: b73353f7 ("drm/amd/display: Use the same cursor info across features")
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Missed enabling timing sync on DCN32 because DCN32 has a different DML
param.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Cannot report 0 memclk levels even when SMU does not provide any.

[How]
When memclk levels reported by SMU is 0, set levels to 1.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x

Update DF related latencies based on new measurements.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x

[why]
Hardware team recommends we limit dispclock to 1950Mhz for all DCN3.2.x

[how]
Limit to 1950 when initializing clocks.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x

Ignore cable ID for DP2 receivers that does not support the feature.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

dcn314 has 4 DSC - conflicted hardware document updated and confirmed.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Leo Chen <sancchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x

Pull fbdev fixes from Helge Deller:
 "A use-after-free bugfix in the smscufx driver and various minor error
  path fixes, smaller build fixes, sysfs fixes and typos in comments in
  the stifb, sisfb, da8xxfb, xilinxfb, sm501fb, gbefb and cyber2000fb
  drivers"

* tag 'fbdev-for-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
  fbdev: cyber2000fb: fix missing pci_disable_device()
  fbdev: sisfb: use explicitly signed char
  fbdev: smscufx: Fix several use-after-free bugs
  fbdev: xilinxfb: Make xilinxfb_release() return void
  fbdev: sisfb: fix repeated word in comment
  fbdev: gbefb: Convert sysfs snprintf to sysfs_emit
  fbdev: sm501fb: Convert sysfs snprintf to sysfs_emit
  fbdev: stifb: Fall back to cfb_fillrect() on 32-bit HCRX cards
  fbdev: da8xx-fb: Fix error handling in .remove()
  fbdev: MIPS supports iomem addresses

Pull char/misc fixes from Greg KH:
 "Some small driver fixes for 6.1-rc3.  They include:

   - iio driver bugfixes

   - counter driver bugfixes

   - coresight bugfixes, including a revert and then a second fix to get
     it right.

  All of these have been in linux-next with no reported problems"

* tag 'char-misc-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
  misc: sgi-gru: use explicitly signed char
  coresight: cti: Fix hang in cti_disable_hw()
  Revert "coresight: cti: Fix hang in cti_disable_hw()"
  counter: 104-quad-8: Fix race getting function mode and direction
  counter: microchip-tcb-capture: Handle Signal1 read and Synapse
  coresight: cti: Fix hang in cti_disable_hw()
  coresight: Fix possible deadlock with lock dependency
  counter: ti-ecap-capture: fix IS_ERR() vs NULL check
  counter: Reduce DEFINE_COUNTER_ARRAY_POLARITY() to defining counter_array
  iio: bmc150-accel-core: Fix unsafe buffer attributes
  iio: adxl367: Fix unsafe buffer attributes
  iio: adxl372: Fix unsafe buffer attributes
  iio: at91-sama5d2_adc: Fix unsafe buffer attributes
  iio: temperature: ltc2983: allocate iio channels once
  tools: iio: iio_utils: fix digit calculation
  iio: adc: stm32-adc: fix channel sampling time init
  iio: adc: mcp3911: mask out device ID in debug prints
  iio: adc: mcp3911: use correct id bits
  iio: adc: mcp3911: return proper error code on failure to allocate trigger
  iio: adc: mcp3911: fix sizeof() vs ARRAY_SIZE() bug
  ...

Pull USB fixes from Greg KH:
 "A few small USB fixes for 6.1-rc3. Include in here are:

   - MAINTAINERS update, including a big one for the USB gadget
     subsystem. Many thanks to Felipe for all of the years of hard work
     he has done on this codebase, it was greatly appreciated.

   - dwc3 driver fixes for reported problems.

   - xhci driver fixes for reported problems.

   - typec driver fixes for minor issues

   - uvc gadget driver change, and then revert as it wasn't relevant for
     6.1-final, as it is a new feature and people are still reviewing
     and modifying it.

  All of these have been in the linux-next tree with no reported issues"

* tag 'usb-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: dwc3: gadget: Don't set IMI for no_interrupt
  usb: dwc3: gadget: Stop processing more requests on IMI
  Revert "usb: gadget: uvc: limit isoc_sg to super speed gadgets"
  xhci: Remove device endpoints from bandwidth list when freeing the device
  xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices
  xhci: Add quirk to reset host back to default state at shutdown
  usb: xhci: add XHCI_SPURIOUS_SUCCESS to ASM1042 despite being a V0.96 controller
  usb: dwc3: st: Rely on child's compatible instead of name
  usb: gadget: uvc: limit isoc_sg to super speed gadgets
  usb: bdc: change state when port disconnected
  usb: typec: ucsi: acpi: Implement resume callback
  usb: typec: ucsi: Check the connection on resume
  usb: gadget: aspeed: Fix probe regression
  usb: gadget: uvc: fix sg handling during video encode
  usb: gadget: uvc: fix sg handling in error case
  usb: gadget: uvc: fix dropped frame after missed isoc
  usb: dwc3: gadget: Don't delay End Transfer on delayed_status
  usb: dwc3: Don't switch OTG -> peripheral if extcon is present
  MAINTAINERS: Update maintainers for broadcom USB
  MAINTAINERS: move USB gadget and phy entries under the main USB entry

Pull gpio fixes from Bartosz Golaszewski:

 - convert gpio-tegra to using an immutable irqchip

 - MAINTAINERS update

* tag 'gpio-fixes-for-v6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  MAINTAINERS: Change myself to a maintainer
  gpio: tegra: Convert to immutable irq chip

Pull perf fixes from Borislav Petkov:

 - Rename a perf memory level event define to denote it is of CXL type

 - Add Alder and Raptor Lakes support to RAPL

 - Make sure raw sample data is output with tracepoints

* tag 'perf_urgent_for_v6.1_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/mem: Rename PERF_MEM_LVLNUM_EXTN_MEM to PERF_MEM_LVLNUM_CXL
  perf/x86/rapl: Add support for Intel Raptor Lake
  perf/x86/rapl: Add support for Intel AlderLake-N
  perf: Fix missing raw data on tracepoint events

Merge tag 'loongarch-fixes-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson

Pull LoongArch fixes from Huacai Chen:
 "Remove unused kernel stack padding, fix some build errors/warnings and
  two bugs in laptop platform driver"

* tag 'loongarch-fixes-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
  platform/loongarch: laptop: Fix possible UAF and simplify generic_acpi_laptop_init()
  platform/loongarch: laptop: Adjust resume order for loongson_hotkey_resume()
  LoongArch: BPF: Avoid declare variables in switch-case
  LoongArch: Use flexible-array member instead of zero-length array
  LoongArch: Remove unused kernel stack padding

Pull cifs fixes from Steve French:

 - use after free fix for reconnect race

 - two memory leak fixes

* tag '6.1-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix use-after-free caused by invalid pointer `hostname`
  cifs: Fix pages leak when writedata alloc failed in cifs_write_from_iter()
  cifs: Fix pages array leak when writedata alloc failed in cifs_writedata_alloc()

Pull random number generator fix from Jason Donenfeld:
 "One fix from Jean-Philippe Brucker, addressing a regression in which
  early boot code on ARM64 would use the non-_early variant of the
  arch_get_random family of functions, resulting in the architectural
  random number generator appearing unavailable during that early phase
  of boot.

  The fix simply changes arch_get_random*() to arch_get_random*_early().

  This distinction between these two functions is a bit of an old wart
  I'm not a fan of, and for 6.2 I'll see if I can make obsolete the
  _early variant, so that one function does the right thing in all
  contexts without overhead"

* tag 'random-6.1-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
  random: use arch_get_random*_early() in random_init()

Pull SCSI fixes from James Bottomley:
 "Varions small  fixes, all  in drivers.

  Some of these arrived during the merge window and got held over to
  make sure of testing on the -rc tree.

  The biggest change is for standards conformance in the target driver,
  closely followed by a set of bug fixes in megaraid_sas"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
  scsi: ufs: core: Fix typo in comment
  scsi: mpi3mr: Select CONFIG_SCSI_SAS_ATTRS
  scsi: ufs: core: Fix typo for register name in comments
  scsi: pm80xx: Display proc_name in sysfs
  scsi: ufs: core: Fix the error log in ufshcd_query_flag_retry()
  scsi: ufs: core: Remove unneeded casts from void *
  scsi: lpfc: Fix spelling mistake "unsolicted" -> "unsolicited"
  scsi: qla2xxx: Use transport-defined speed mask for supported_speeds
  scsi: target: iblock: Fold iblock_emulate_read_cap_with_block_size() into iblock_get_blocks()
  scsi: qla2xxx: Fix serialization of DCBX TLV data request
  scsi: ufs: qcom: Remove redundant dev_err() call
  scsi: megaraid_sas: Move megasas_dbg_lvl init to megasas_init()
  scsi: megaraid_sas: Remove unnecessary memset()
  scsi: megaraid_sas: Simplify megasas_update_device_list
  scsi: megaraid_sas: Correct an error message
  scsi: megaraid_sas: Correct value passed to scsi_device_lookup()
  scsi: target: core: UA on all LUNs after reset
  scsi: target: core: New key must be used for moved PR
  scsi: target: core: Abort all preempted regs if requested
  scsi: target: core: Fix memory leak in preempt_and_abort
  ...

Pull block fixes from Jens Axboe:

 - NVMe pull request via Christoph:
      - make the multipath dma alignment match the non-multipath one
        (Keith Busch)
      - fix a bogus use of sg_init_marker() (Nam Cao)
      - fix circulr locking in nvme-tcp (Sagi Grimberg)

 - Initialization fix for requests allocated via the special hw queue
   allocator (John)

 - Fix for a regression added in this release with the batched
   completions of end_io backed requests (Ming)

 - Error handling leak fix for rbd (Yang)

 - Error handling leak fix for add_disk() failure (Yu)

* tag 'block-6.1-2022-10-28' of git://git.kernel.dk/linux:
  blk-mq: Properly init requests from blk_mq_alloc_request_hctx()
  blk-mq: don't add non-pt request with ->end_io to batch
  rbd: fix possible memory leak in rbd_sysfs_init()
  nvme-multipath: set queue dma alignment to 3
  nvme-tcp: fix possible circular locking when deleting a controller under memory pressure
  nvme-tcp: replace sg_init_marker() with sg_init_table()
  block: fix memory leak for elevator on add_disk failure

Pull io_uring fix from Jens Axboe:
 "Just a fix for a locking regression introduced with the deferred
  task_work running from this merge window"

* tag 'io_uring-6.1-2022-10-28' of git://git.kernel.dk/linux:
  io_uring: unlock if __io_run_local_work locked inside
  io_uring: use io_run_local_work_locked helper

Pull misc hotfixes from Andrew Morton:
 "Eight fix pre-6.0 bugs and the remainder address issues which were
  introduced in the 6.1-rc merge cycle, or address issues which aren't
  considered sufficiently serious to warrant a -stable backport"

* tag 'mm-hotfixes-stable-2022-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (23 commits)
  mm: multi-gen LRU: move lru_gen_add_mm() out of IRQ-off region
  lib: maple_tree: remove unneeded initialization in mtree_range_walk()
  mmap: fix remap_file_pages() regression
  mm/shmem: ensure proper fallback if page faults
  mm/userfaultfd: replace kmap/kmap_atomic() with kmap_local_page()
  x86: fortify: kmsan: fix KMSAN fortify builds
  x86: asm: make sure __put_user_size() evaluates pointer once
  Kconfig.debug: disable CONFIG_FRAME_WARN for KMSAN by default
  x86/purgatory: disable KMSAN instrumentation
  mm: kmsan: export kmsan_copy_page_meta()
  mm: migrate: fix return value if all subpages of THPs are migrated successfully
  mm/uffd: fix vma check on userfault for wp
  mm: prep_compound_tail() clear page->private
  mm,madvise,hugetlb: fix unexpected data loss with MADV_DONTNEED on hugetlbfs
  mm/page_isolation: fix clang deadcode warning
  fs/ext4/super.c: remove unused `deprecated_msg'
  ipc/msg.c: fix percpu_counter use after free
  memory tier, sysfs: rename attribute "nodes" to "nodelist"
  MAINTAINERS: git://github.com -> https://github.com for nilfs2
  mm/kmemleak: prevent soft lockup in kmemleak_scan()'s object iteration loops
  ...

Pull powerpc fixes from Michael Ellerman:

 - Fix a case of rescheduling with user access unlocked, when preempt is
   enabled.

 - A follow-up fix for a recent fix, which could lead to IRQ state
   assertions firing incorrectly.

 - Two fixes for lockdep warnings seen when using kfence with the Hash
   MMU.

 - Two fixes for preempt warnings seen when using the Hash MMU.

 - Two fixes for the VAS coprocessor mechanism used on pseries.

 - Prevent building some of our older KVM backends when
   CONTEXT_TRACKING_USER is enabled, as it's known to cause crashes.

 - A couple of fixes for issues seen with PMU NMIs.

Thanks to Nicholas Piggin, Guenter Roeck, Frederic Barrat Haren Myneni,
Sachin Sant, and Samuel Holland.

* tag 'powerpc-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s/interrupt: Fix clear of PACA_IRQS_HARD_DIS when returning to soft-masked context
  powerpc/64s/interrupt: Perf NMI should not take normal exit path
  powerpc/64/interrupt: Prevent NMI PMI causing a dangerous warning
  KVM: PPC: BookS PR-KVM and BookE do not support context tracking
  powerpc: Fix reschedule bug in KUAP-unlocked user copy
  powerpc/64s: Fix hash__change_memory_range preemption warning
  powerpc/64s: Disable preemption in hash lazy mmu mode
  powerpc/64s: make linear_map_hash_lock a raw spinlock
  powerpc/64s: make HPTE lock and native_tlbie_lock irq-safe
  powerpc/64s: Add lockdep for HPTE lock
  powerpc/pseries: Use lparcfg to reconfig VAS windows for DLPAR CPU
  powerpc/pseries/vas: Add VAS IRQ primary handler

Currently the return value of 'sub_driver->init' is not checked. If
sparse_keymap_setup() called in the init function fails, 'generic_
inputdev' is freed, then it will lead a UAF when using it in generic_
acpi_laptop_init(). Fix it by checking the return value and setting
generic_inputdev to NULL after free, so as to avoid double free it.

The error code in generic_subdriver_init() is always negative, so the
return of generic_subdriver_init() can be simplified.

Fixes: 6246ed09 ("LoongArch: Add ACPI-based generic laptop driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>

Some laptops don't support SW_LID, but still have backlight control,
move backlight resuming before SW_LID event handling so as to avoid
backlight mistake due to early return.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>

Not all compilers support declare variables in switch-case, so move
declarations to the beginning of a function. Otherwise we may get such
build errors:

arch/loongarch/net/bpf_jit.c: In function ‘emit_atomic’:
arch/loongarch/net/bpf_jit.c:362:3: error: a label can only be part of a statement and a declaration is not a statement
   u8 r0 = regmap[BPF_REG_0];
   ^~
arch/loongarch/net/bpf_jit.c: In function ‘build_insn’:
arch/loongarch/net/bpf_jit.c:727:3: error: a label can only be part of a statement and a declaration is not a statement
   u8 t7 = -1;
   ^~
arch/loongarch/net/bpf_jit.c:778:3: error: a label can only be part of a statement and a declaration is not a statement
   int ret;
   ^~~
arch/loongarch/net/bpf_jit.c:779:3: error: expected expression before ‘u64’
   u64 func_addr;
   ^~~
arch/loongarch/net/bpf_jit.c:780:3: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
   bool func_addr_fixed;
   ^~~~
arch/loongarch/net/bpf_jit.c:784:11: error: ‘func_addr’ undeclared (first use in this function); did you mean ‘in_addr’?
          &func_addr, &func_addr_fixed);
           ^~~~~~~~~
           in_addr
arch/loongarch/net/bpf_jit.c:784:11: note: each undeclared identifier is reported only once for each function it appears in
arch/loongarch/net/bpf_jit.c:814:3: error: a label can only be part of a statement and a declaration is not a statement
   u64 imm64 = (u64)(insn + 1)->imm << 32 | (u32)insn->imm;
   ^~~
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>

Eliminate the following coccicheck warning:
./arch/loongarch/include/asm/ptrace.h:32:15-21: WARNING use flexible-array member instead
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Yushan Zhou <katrinzhou@tencent.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>

The current LoongArch kernel stack is padded as if obeying the MIPS o32
calling convention (32 bytes), signifying the port's MIPS lineage but no
longer making sense. Remove the padding for clarity.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>

Pull s390 fixes from Vasily Gorbik:

 - Remove outdated linux390 link from MAINTAINERS

 - Add few missing EX_TABLE entries to inline assemblies

 - Fix raw data collection for pai_ext PMU

 - Add kernel image secure boot trailer for future firmware versions

 - Fix out-of-bounds access on cio_ignore free

 - Fix memory allocation of mdev_types array in vfio-ap

* tag 's390-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/vfio-ap: Fix memory allocation for mdev_types array
  s390/cio: fix out-of-bounds access on cio_ignore free
  s390/pai: fix raw data collection for PMU pai_ext
  s390/boot: add secure boot trailer
  s390/pci: add missing EX_TABLE entries to __pcistg_mio_inuser()/__pcilg_mio_inuser()
  s390/futex: add missing EX_TABLE entry to __futex_atomic_op()
  s390/uaccess: add missing EX_TABLE entries to __clear_user()
  MAINTAINERS: remove outdated linux390 link

Pull RISC-V fixes from Palmer Dabbelt:

 - A fix for a build warning in the jump_label code

 - One of the git://github -> https://github cleanups, for the SiFive
   drivers

 - A fix for the kasan initialization code, this still likely warrants
   some cleanups but that's a bigger problem and at least this fixes the
   crashes in the short term

 - A pair of fixes for extension support detection on mixed LLVM/GNU
   toolchains

 - A fix for a runtime warning in the /proc/cpuinfo code

* tag 'riscv-for-linus-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  RISC-V: Fix /proc/cpuinfo cpumask warning
  riscv: fix detection of toolchain Zihintpause support
  riscv: fix detection of toolchain Zicbom support
  riscv: mm: add missing memcpy in kasan_init
  MAINTAINERS: git://github.com -> https://github.com for sifive
  riscv: jump_label: mark arguments as const to satisfy asm constraints

Pull ACPI and device properties fixes from Rafael Wysocki:
 "These fix device properties documentation and the ACPI PCC code, add a
  new IRQ override quirk for resource handling and add one more item to
  the list of device IDs to be ignored when returned by _DEP.

  Specifics:

   - Fix the documentation of the *_match_string() family of functions
     to properly cover the return value (Andy Shevchenko)

   - Fix a possible integer overflow during multiplication in the ACPI
     PCC code (Manank Patel)

   - Make the ACPI device resources code skip IRQ override on Asus
     Vivobook S5602ZA (Tamim Khan)

   - Add LATT2021 to the list of device IDs that are ignored when
     returned by _DEP, because there are no drivers for them in the
     kernel and no plans to add such drivers (Hans de Goede)"

* tag 'acpi-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: scan: Add LATT2021 to acpi_ignore_dep_ids[]
  ACPI: resource: Skip IRQ override on Asus Vivobook S5602ZA
  ACPI: PCC: Fix unintentional integer overflow
  device property: Fix documentation for *_match_string() APIs