Pull USB fixes from Greg KH:
 "Here are some USB fixes for 5.14-rc3 to resolve a bunch of tiny
  problems reported. Included in here are:

   - dtsi revert to resolve a problem which broke android systems that
     relied on the dts name to find the USB controller device.

     People are still working out the "real" solution for this, but for
     now the revert is needed.

   - core USB fix for pipe calculation found by syzbot

   - typec fixes

   - gadget driver fixes

   - new usb-serial device ids

   - new USB quirks

   - xhci fixes

   - usb hub fixes for power management issues reported

   - other tiny fixes

  All have been in linux-next with no reported problems"

* tag 'usb-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (27 commits)
  USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
  Revert "USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem"
  usb: cdc-wdm: fix build error when CONFIG_WWAN_CORE is not set
  Revert "arm64: dts: qcom: Harmonize DWC USB3 DT nodes name"
  usb: dwc2: gadget: Fix sending zero length packet in DDMA mode.
  usb: dwc2: Skip clock gating on Samsung SoCs
  usb: renesas_usbhs: Fix superfluous irqs happen after usb_pkt_pop()
  usb: dwc2: gadget: Fix GOUTNAK flow for Slave mode.
  usb: phy: Fix page fault from usb_phy_uevent
  usb: xhci: avoid renesas_usb_fw.mem when it's unusable
  usb: gadget: u_serial: remove WARN_ON on null port
  usb: dwc3: avoid NULL access of usb_gadget_driver
  usb: max-3421: Prevent corruption of freed memory
  usb: gadget: Fix Unbalanced pm_runtime_enable in tegra_xudc_probe
  MAINTAINERS: repair reference in USB IP DRIVER FOR HISILICON KIRIN 970
  usb: typec: stusb160x: Don't block probing of consumer of "connector" nodes
  usb: typec: stusb160x: register role switch before interrupt registration
  USB: usb-storage: Add LaCie Rugged USB3-FW to IGNORE_UAS
  usb: ehci: Prevent missed ehci interrupts with edge-triggered MSI
  usb: hub: Disable USB 3 device initiated lpm if exit latency is too high
  ...

Pull sound fixes from Takashi Iwai:
 "A collection of small fixes, mostly covering device-specific
  regressions and bugs over ASoC, HD-audio and USB-audio, while
  the ALSA PCM core received a few additional fixes for the
  possible (new and old) regressions"

* tag 'sound-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (29 commits)
  ALSA: usb-audio: Add registration quirk for JBL Quantum headsets
  ALSA: hda/hdmi: Add quirk to force pin connectivity on NUC10
  ALSA: pcm: Fix mmap without buffer preallocation
  ALSA: pcm: Fix mmap capability check
  ALSA: hda: intel-dsp-cfg: add missing ElkhartLake PCI ID
  ASoC: ti: j721e-evm: Check for not initialized parent_clk_id
  ASoC: ti: j721e-evm: Fix unbalanced domain activity tracking during startup
  ALSA: hda/realtek: Fix pop noise and 2 Front Mic issues on a machine
  ALSA: hdmi: Expose all pins on MSI MS-7C94 board
  ALSA: sb: Fix potential ABBA deadlock in CSP driver
  ASoC: rt5682: Fix the issue of garbled recording after powerd_dbus_suspend
  ASoC: amd: reverse stop sequence for stoneyridge platform
  ASoC: soc-pcm: add a flag to reverse the stop sequence
  ASoC: codecs: wcd938x: setup irq during component bind
  ASoC: dt-bindings: renesas: rsnd: Fix incorrect 'port' regex schema
  ALSA: usb-audio: Add missing proc text entry for BESPOKEN type
  ASoC: codecs: wcd938x: make sdw dependency explicit in Kconfig
  ASoC: SOF: Intel: Update ADL descriptor to use ACPI power states
  ASoC: rt5631: Fix regcache sync errors on resume
  ALSA: pcm: Call substream ack() method upon compat mmap commit
  ...

Pull drm fixes from Dave Airlie:
 "Regular fixes - a bunch of amdgpu fixes are the main thing mostly for
  the new gpus. There is also some i915 reverts for older changes that
  were having some unwanted side effects. One nouveau fix for a report
  regressions, and otherwise just some misc fixes.

  core:
   - fix for non-drm ioctls on drm fd

  panel:
   - avoid double free

  ttm:
   - refcounting fix
   - NULL checks

  amdgpu:
   - Yellow Carp updates
   - Add some Yellow Carp DIDs
   - Beige Goby updates
   - CIK 10bit 4K regression fix
   - GFX10 golden settings updates
   - eDP panel regression fix
   - Misc display fixes
   - Aldebaran fix
   - fix COW checks

  nouveau:
   - init BO GEM fields

  i915:
   - revert async command parsing
   - revert fence error propogation
   - GVT fix for shadow ppgtt

  vc4:
   - fix interrupt handling"

* tag 'drm-fixes-2021-07-23' of git://anongit.freedesktop.org/drm/drm: (34 commits)
  drm/panel: raspberrypi-touchscreen: Prevent double-free
  drm/amdgpu - Corrected the video codecs array name for yellow carp
  drm/amd/display: Fix ASSR regression on embedded panels
  drm/amdgpu: add yellow carp pci id (v2)
  drm/amdgpu: update yellow carp external rev_id handling
  drm/amd/pm: Support board calibration on aldebaran
  drm/amd/display: change zstate allow msg condition
  drm/amd/display: Populate dtbclk entries for dcn3.02/3.03
  drm/amd/display: Line Buffer changes
  drm/amd/display: Remove MALL function from DCN3.1
  drm/amd/display: Only set default brightness for OLED
  drm/amd/display: Update bounding box for DCN3.1
  drm/amd/display: Query VCO frequency from register for DCN3.1
  drm/amd/display: Populate socclk entries for dcn3.02/3.03
  drm/amd/display: Fix max vstartup calculation for modes with borders
  drm/amd/display: implement workaround for riommu related hang
  drm/amd/display: Fix comparison error in dcn21 DML
  drm/i915: Correct the docs for intel_engine_cmd_parser
  drm/ttm: add missing NULL checks
  drm/ttm: Force re-init if ttm_global_init() fails
  ...

Merge tag 'fallthrough-fixes-clang-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux

Pull fallthrough fix from Gustavo Silva:
 "Fix a fall-through warning when building with -Wimplicit-fallthrough
  on PowerPC"

* tag 'fallthrough-fixes-clang-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
  powerpc/pasemi: Fix fall-through warning for Clang

Short summary of fixes pull:

 * Return -ENOTTY for non-DRM ioctls
 * amdgpu: Fix COW checks
 * nouveau: init BO GME fields
 * panel: Avoid double free
 * ttm: Fix refcounting in ttm_global_init(); NULL checks
 * vc4: Fix interrupt handling
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YPlbkmH6S4VAHP9j@linux-uq9g.fritz.box

Merge tag 'drm-intel-fixes-2021-07-22' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

Couple reverts from Jason getting rid of asynchronous command parsing
and fence error propagation and a GVT fix of shadow ppgtt invalidation
with proper D3 state tracking from Colin.
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YPl1sIyruD0U5Orl@intel.com

Merge tag 'array-bounds-fixes-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux

Pull array bounds warning fix from Gustavo Silva:
 "Fix a couple of out-of-bounds warnings in the media subsystem.

  This is part of the ongoing efforts to globally enable -Warray-bounds"

* tag 'array-bounds-fixes-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
  media: ngene: Fix out-of-bounds bug in ngene_command_config_free_buf()

Merge tag 'usb-serial-5.14-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for 5.14-rc3

Here are some new device ids and a device-id comment fix.

All have been in linux-next with no reported issues.

* tag 'usb-serial-5.14-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
  USB: serial: cp210x: fix comments for GE CS1000
  USB: serial: option: add support for u-blox LARA-R6 family

Pull arm64 fixes from Will Deacon:
 "A pair of arm64 fixes for -rc3. The straightforward one is a fix to
  our firmware calling stub, which accidentally started corrupting the
  link register on machines with SVE. Since these machines don't really
  exist yet, it wasn't spotted in -next.

  The other fix is a revert-and-a-bit of a patch originally intended to
  allow PTE-level huge mappings for the VMAP area on 32-bit PPC 8xx. A
  side-effect of this change was that our pXd_set_huge() implementations
  could be replaced with generic dummy functions depending on the levels
  of page-table being used, which in turn broke the boot if we fail to
  create the linear mapping as a result of using these functions to
  operate on the pgd. Huge thanks to Michael Ellerman for modifying the
  revert so as not to regress PPC 8xx in terms of functionality.

  Anyway, that's the background and it's also available in the commit
  message along with Link tags pointing at all of the fun.

  Summary:

   - Fix hang when issuing SMC on SVE-capable system due to
     clobbered LR

   - Fix boot failure due to missing block mappings with folded
     page-table"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  Revert "mm/pgtable: add stubs for {pmd/pub}_{set/clear}_huge"
  arm64: smccc: Save lr before calling __arm_smccc_sve_check()

Merge tag 'hyperv-fixes-signed-20210722' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux

Pull hyperv fixes from Wei Liu:

 - bug fix from Haiyang for vmbus CPU assignment

 - revert of a bogus patch that went into 5.14-rc1

* tag 'hyperv-fixes-signed-20210722' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
  Revert "x86/hyperv: fix logical processor creation"
  Drivers: hv: vmbus: Fix duplicate CPU assignments within a device

Pull networking fixes from David Miller:

 1) Fix type of bind option flag in af_xdp, from Baruch Siach.

 2) Fix use after free in bpf_xdp_link_release(), from Xuan Zhao.

 3) PM refcnt imbakance in r8152, from Takashi Iwai.

 4) Sign extension ug in liquidio, from Colin Ian King.

 5) Mising range check in s390 bpf jit, from Colin Ian King.

 6) Uninit value in caif_seqpkt_sendmsg(), from Ziyong Xuan.

 7) Fix skb page recycling race, from Ilias Apalodimas.

 8) Fix memory leak in tcindex_partial_destroy_work, from Pave Skripkin.

 9) netrom timer sk refcnt issues, from Nguyen Dinh Phi.

10) Fix data races aroun tcp's tfo_active_disable_stamp, from Eric
    Dumazet.

11) act_skbmod should only operate on ethernet packets, from Peilin Ye.

12) Fix slab out-of-bpunds in fib6_nh_flush_exceptions(),, from Psolo
    Abeni.

13) Fix sparx5 dependencies, from Yajun Deng.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (74 commits)
  dpaa2-switch: seed the buffer pool after allocating the swp
  net: sched: cls_api: Fix the the wrong parameter
  net: sparx5: fix unmet dependencies warning
  net: dsa: tag_ksz: dont let the hardware process the layer 4 checksum
  net: dsa: ensure linearized SKBs in case of tail taggers
  ravb: Remove extra TAB
  ravb: Fix a typo in comment
  net: dsa: sja1105: make VID 4095 a bridge VLAN too
  tcp: disable TFO blackhole logic by default
  sctp: do not update transport pathmtu if SPP_PMTUD_ENABLE is not set
  net: ixp46x: fix ptp build failure
  ibmvnic: Remove the proper scrq flush
  selftests: net: add ESP-in-UDP PMTU test
  udp: check encap socket in __udp_lib_err
  sctp: update active_key for asoc when old key is being replaced
  r8169: Avoid duplicate sysfs entry creation error
  ixgbe: Fix packet corruption due to missing DMA sync
  Revert "qed: fix possible unpaired spin_{un}lock_bh in _qed_mcp_cmd_and_union()"
  ipv6: fix another slab-out-of-bounds in fib6_nh_flush_exceptions
  fsl/fman: Add fibre support
  ...

Pull MMC fixes from Ulf Hansson:

 - Use kref to fix KASAN splats triggered during card removal

 - Don't allocate IDA for OF aliases

* tag 'mmc-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: core: Don't allocate IDA for OF aliases
  mmc: core: Use kref in place of struct mmc_blk_data::usage

Any interraction with the buffer pool (seeding a buffer, acquire one) is
made through a software portal (SWP, a DPIO object).
There are circumstances where the dpaa2-switch driver probes on a DPSW
before any DPIO devices have been probed. In this case, seeding of the
buffer pool will lead to a panic since no SWPs are initialized.

To fix this, seed the buffer pool after making sure that the software
portals have been probed and are ready to be used.

Fixes: 0b1b7137 ("staging: dpaa2-switch: handle Rx path on control interface")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mipi_dsi_device allocated by mipi_dsi_device_register_full() is
already free'd on release.

Fixes: 2f733d61 ("drm/panel: Add support for the Raspberry Pi 7" Touchscreen.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720134525.563936-9-maxime@cerno.tech

The 4th parameter in tc_chain_notify() should be flags rather than seq.
Let's change it back correctly.

Fixes: 32a4f5ec ("net: sched: introduce chain object to uapi")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

WARNING: unmet direct dependencies detected for PHY_SPARX5_SERDES
  Depends on [n]: (ARCH_SPARX5 || COMPILE_TEST [=n]) && OF [=y] && HAS_IOMEM [=y]
  Selected by [y]:
  - SPARX5_SWITCH [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICROCHIP [=y] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y] && OF [=y]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These devices has two interfaces, but only the second interface
contains the capture endpoint, thus quirk is required to delay the
registration until the second interface appears.
Tested-by: Jakub Fišer <jakub@ufiseru.cz>
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210721235605.53741-1-alexander@tsoy.meSigned-off-by: Takashi Iwai <tiwai@suse.de>

Lino Sanfilippo says:

====================
Fixes for KSZ DSA switch

These patches fix issues I encountered while using a KSZ9897 as a DSA
switch with a broadcom GENET network device as the DSA master device.

PATCH 1 fixes an invalid access to an SKB in case it is scattered.
PATCH 2 fixes incorrect hardware checksum calculation caused by the DSA
tag.

Changes in v2:
- instead of linearizing the SKBs only for KSZ switches ensure linearized
  SKBs for all tail taggers by clearing the feature flags NETIF_F_HW_SG and
  NETIF_F_FRAGLIST (suggested by Vladimir Oltean)

The patches have been tested with a KSZ9897 and apply against net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If the checksum calculation is offloaded to the network device (e.g due to
NETIF_F_HW_CSUM inherited from the DSA master device), the calculated
layer 4 checksum is incorrect. This is since the DSA tag which is placed
after the layer 4 data is considered as being part of the daa and thus
errorneously included into the checksum calculation.
To avoid this, always calculate the layer 4 checksum in software.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function skb_put() that is used by tail taggers to make room for the
DSA tag must only be called for linearized SKBS. However in case that the
slave device inherited features like NETIF_F_HW_SG or NETIF_F_FRAGLIST the
SKB passed to the slaves transmit function may not be linearized.
Avoid those SKBs by clearing the NETIF_F_HW_SG and NETIF_F_FRAGLIST flags
for tail taggers.
Furthermore since the tagging protocol can be changed at runtime move the
code for setting up the slaves features into dsa_slave_setup_tagger().
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Align the member description comments for struct ravb_desc by
removing the extra TAB.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the typo RX->TX in comment, as the code following the comment
process TX and not RX.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This simple series of commands:

ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0

fails on sja1105 with the following error:
[   33.439103] sja1105 spi0.1: vlan-lookup-table needs to have at least the default untagged VLAN
[   33.447710] sja1105 spi0.1: Invalid config, cannot upload
Warning: sja1105: Failed to change VLAN Ethertype.

For context, sja1105 has 3 operating modes:
- SJA1105_VLAN_UNAWARE: the dsa_8021q_vlans are committed to hardware
- SJA1105_VLAN_FILTERING_FULL: the bridge_vlans are committed to hardware
- SJA1105_VLAN_FILTERING_BEST_EFFORT: both the dsa_8021q_vlans and the
  bridge_vlans are committed to hardware

Swapping out a VLAN list and another in happens in
sja1105_build_vlan_table(), which performs a delta update procedure.
That function is called from a few places, notably from
sja1105_vlan_filtering() which is called from the
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler.

The above set of 2 commands fails when run on a kernel pre-commit
8841f6e6 ("net: dsa: sja1105: make devlink property
best_effort_vlan_filtering true by default"). So the priv->vlan_state
transition that takes place is between VLAN-unaware and full VLAN
filtering. So the dsa_8021q_vlans are swapped out and the bridge_vlans
are swapped in.

So why does it fail?

Well, the bridge driver, through nbp_vlan_init(), first sets up the
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING attribute, and only then
proceeds to call nbp_vlan_add for the default_pvid.

So when we swap out the dsa_8021q_vlans and swap in the bridge_vlans in
the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler, there are no bridge
VLANs (yet). So we have wiped the VLAN table clean, and the low-level
static config checker complains of an invalid configuration. We _will_
add the bridge VLANs using the dynamic config interface, albeit later,
when nbp_vlan_add() calls us. So it is natural that it fails.

So why did it ever work?

Surprisingly, it looks like I only tested this configuration with 2
things set up in a particular way:
- a network manager that brings all ports up
- a kernel with CONFIG_VLAN_8021Q=y

It is widely known that commit ad1afb00 ("vlan_dev: VLAN 0 should be
treated as "no vlan tag" (802.1p packet)") installs VID 0 to every net
device that comes up. DSA treats these VLANs as bridge VLANs, and
therefore, in my testing, the list of bridge_vlans was never empty.

However, if CONFIG_VLAN_8021Q is not enabled, or the port is not up when
it joins a VLAN-aware bridge, the bridge_vlans list will be temporarily
empty, and the sja1105_static_config_reload() call from
sja1105_vlan_filtering() will fail.

To fix this, the simplest thing is to keep VID 4095, the one used for
CPU-injected control packets since commit ed040abc ("net: dsa:
sja1105: use 4095 as the private VLAN for untagged traffic"), in the
list of bridge VLANs too, not just the list of tag_8021q VLANs. This
ensures that the list of bridge VLANs will never be empty.

Fixes: ec5ae610 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Reported-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Multiple complaints have been raised from the TFO users on the internet
stating that the TFO blackhole logic is too aggressive and gets falsely
triggered too often.
(e.g. https://blog.apnic.net/2021/07/05/tcp-fast-open-not-so-fast/)
Considering that most middleboxes no longer drop TFO packets, we decide
to disable the blackhole logic by setting
/proc/sys/net/ipv4/tcp_fastopen_blackhole_timeout_set to 0 by default.

Fixes: cf1ef3f0 ("net/tcp_fastopen: Disable active side TFO in certain scenarios")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'amd-drm-fixes-5.14-2021-07-21' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-5.14-2021-07-21:

amdgpu:
- Yellow Carp updates
- Add some Yellow Carp DIDs
- Beige Goby updates
- CIK 10bit 4K regression fix
- GFX10 golden settings updates
- eDP panel regression fix
- Misc display fixes
- Aldebaran fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721215800.17590-1-alexander.deucher@amd.com

Signed-off-by: Veerabadhran Gopalakrishnan <veerabadhran.gopalakrishnan@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Currently, in sctp_packet_config(), sctp_transport_pmtu_check() is
called to update transport pathmtu with dst's mtu when dst's mtu
has been changed by non sctp stack like xfrm.

However, this should only happen when SPP_PMTUD_ENABLE is set, no
matter where dst's mtu changed. This patch is to fix by checking
SPP_PMTUD_ENABLE flag before calling sctp_transport_pmtu_check().

Thanks Jacek for reporting and looking into this issue.

v1->v2:
  - add the missing "{" to fix the build error.

Fixes: 69fec325 ('Revert "sctp: remove sctp_transport_pmtu_check"')
Reported-by: Jacek Szafraniec <jacek.szafraniec@nokia.com>
Tested-by: Jacek Szafraniec <jacek.szafraniec@nokia.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull s390 updates from Heiko Carstens:

 - fix / add expoline usage in "DMA" code

 - fix compat vdso Makefile to avoid permanent rebuild

 - fix ftrace_update_ftrace_func to avoid NULL pointer dereference

 - update defconfigs

 - trivial coding style fix

* tag 's390-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: update defconfigs
  s390/cpumf: fix semicolon.cocci warnings
  s390/boot: fix use of expolines in the DMA code
  s390/ftrace: fix ftrace_update_ftrace_func implementation
  s390/defconfig: allow early device mapper disks
  s390/vdso32: add vdso32.lds to targets

Pull spi fixes from Mark Brown:
 "A collection of driver specific fixes, there was a bit of a kerfuffle
  with some last minute review on hte spi-cadence-quadspi division by
  zero change but otherwise nothing terribly remarkable here - important
  fixes if you have the hardware but nothing with too wide an impact"

* tag 'spi-fix-v5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: spi-bcm2835: Fix deadlock
  spi: cadence: Correct initialisation of runtime PM again
  spi: cadence-quadspi: Disable Auto-HW polling
  spi: spi-cadence-quadspi: Fix division by zero warning
  spi: spi-cadence-quadspi: Revert "Fix division by zero warning"
  spi: spi-cadence-quadspi: Fix division by zero warning
  spi: mediatek: move devm_spi_register_master position
  spi: mediatek: fix fifo rx mode
  spi: atmel: Fix CS and initialization bug
  spi: stm32: fixes pm_runtime calls in probe/remove
  spi: imx: mx51-ecspi: Reinstate low-speed CONFIGREG delay
  spi: stm32h7: fix full duplex irq handler handling

Merge tag 'regulator-fix-v5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "A few driver specific fixes that came in since the merge window, plus
  a change to mark the regulator-fixed-domain DT binding as deprecated
  in order to try to to discourage any new users while a better solution
  is put in place"

* tag 'regulator-fix-v5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: hi6421: Fix getting wrong drvdata
  regulator: mtk-dvfsrc: Fix wrong dev pointer for devm_regulator_register
  regulator: fixed: Mark regulator-fixed-domain as deprecated
  regulator: bd9576: Fix testing wrong flag in check_temp_flag_mismatch
  regulator: hi6421v600: Fix getting wrong drvdata that causes boot failure
  regulator: rt5033: Fix n_voltages settings for BUCK and LDO
  regulator: rtmv20: Fix wrong mask for strobe-polarity-high

Pull AFS fixes from David Howells:

 - Fix a tracepoint that causes one of the tracing subsystem query files
   to crash if the module is loaded

 - Fix afs_writepages() to take account of whether the storage rpc
   actually succeeded when updating the cyclic writeback counter

 - Fix some error code propagation/handling

 - Fix place where afs_writepages() was setting writeback_index to a
   file position rather than a page index

* tag 'afs-fixes-20210721' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: Remove redundant assignment to ret
  afs: Fix setting of writeback_index
  afs: check function return
  afs: Fix tracepoint string placement with built-in AFS

[Why]
Regression found in some embedded panels traces back to the earliest
upstreamed ASSR patch. The changed code flow are causing problems
with some panels.

[How]
- Change ASSR enabling code while preserving original code flow
  as much as possible
- Simplify the code on guarding with internal display flag

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213779
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1620Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Add Yellow Carp PCI id support.

v2: add another DID
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

0x1681 has a different external revision id.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support for board power calibration on Aldebaran.
Board calibration is done after DC offset calibration.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
PMFW message which previously thought to only control Z9 controls both
Z9 and Z10. Also HW design team requested that Z9 must only be supported
on eDP due to content protection interop.

[How]
Change zstate support condition to match updated policy
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Populate dtbclk values from bwparams for dcn302, dcn303.

[How]
dtbclk values are fetched from bandwidthparams for all DPM levels and
for DPM levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
DCN31 doesn't have MALL in DMUB so to avoid sending unknown commands to
DMUB just remove the function pointer.

[how]
Remove apply_idle_power_optimizations from function pointers structure
for DCN31
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.

[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>